Subversion Repositories libSerial

Rev

Blame | Last modification | View Log | Download | RSS feed

  1. /* USER CODE BEGIN Header */
  2. /**
  3.   ******************************************************************************
  4.   * @file    stm32f1xx_hal_conf.h
  5.   * @brief   HAL configuration file.
  6.   ******************************************************************************
  7.   * @attention
  8.   *
  9.   * Copyright (c) 2017 STMicroelectronics.
  10.   * All rights reserved.
  11.   *
  12.   * This software is licensed under terms that can be found in the LICENSE file
  13.   * in the root directory of this software component.
  14.   * If no LICENSE file comes with this software, it is provided AS-IS.
  15.   *
  16.   ******************************************************************************
  17.   */
  18. /* USER CODE END Header */
  19.  
  20. /* Define to prevent recursive inclusion -------------------------------------*/
  21. #ifndef __STM32F1xx_HAL_CONF_H
  22. #define __STM32F1xx_HAL_CONF_H
  23.  
  24. #ifdef __cplusplus
  25.  extern "C" {
  26. #endif
  27.  
  28. /* Exported types ------------------------------------------------------------*/
  29. /* Exported constants --------------------------------------------------------*/
  30.  
  31. /* ########################## Module Selection ############################## */
  32. /**
  33.   * @brief This is the list of modules to be used in the HAL driver
  34.   */
  35.  
  36. #define HAL_MODULE_ENABLED
  37.   /*#define HAL_ADC_MODULE_ENABLED   */
  38. /*#define HAL_CRYP_MODULE_ENABLED   */
  39. #define HAL_CAN_MODULE_ENABLED
  40. /*#define HAL_CAN_LEGACY_MODULE_ENABLED   */
  41. /*#define HAL_CEC_MODULE_ENABLED   */
  42. /*#define HAL_CORTEX_MODULE_ENABLED   */
  43. /*#define HAL_CRC_MODULE_ENABLED   */
  44. /*#define HAL_DAC_MODULE_ENABLED   */
  45. /*#define HAL_DMA_MODULE_ENABLED   */
  46. /*#define HAL_ETH_MODULE_ENABLED   */
  47. /*#define HAL_FLASH_MODULE_ENABLED   */
  48. #define HAL_GPIO_MODULE_ENABLED
  49. /*#define HAL_I2C_MODULE_ENABLED   */
  50. /*#define HAL_I2S_MODULE_ENABLED   */
  51. /*#define HAL_IRDA_MODULE_ENABLED   */
  52. /*#define HAL_IWDG_MODULE_ENABLED   */
  53. /*#define HAL_NOR_MODULE_ENABLED   */
  54. /*#define HAL_NAND_MODULE_ENABLED   */
  55. /*#define HAL_PCCARD_MODULE_ENABLED   */
  56. /*#define HAL_PCD_MODULE_ENABLED   */
  57. /*#define HAL_HCD_MODULE_ENABLED   */
  58. /*#define HAL_PWR_MODULE_ENABLED   */
  59. /*#define HAL_RCC_MODULE_ENABLED   */
  60. /*#define HAL_RTC_MODULE_ENABLED   */
  61. /*#define HAL_SD_MODULE_ENABLED   */
  62. /*#define HAL_MMC_MODULE_ENABLED   */
  63. /*#define HAL_SDRAM_MODULE_ENABLED   */
  64. /*#define HAL_SMARTCARD_MODULE_ENABLED   */
  65. #define HAL_SPI_MODULE_ENABLED
  66. /*#define HAL_SRAM_MODULE_ENABLED   */
  67. /*#define HAL_TIM_MODULE_ENABLED   */
  68. #define HAL_UART_MODULE_ENABLED
  69. /*#define HAL_USART_MODULE_ENABLED   */
  70. /*#define HAL_WWDG_MODULE_ENABLED   */
  71.  
  72. #define HAL_CORTEX_MODULE_ENABLED
  73. #define HAL_DMA_MODULE_ENABLED
  74. #define HAL_FLASH_MODULE_ENABLED
  75. #define HAL_EXTI_MODULE_ENABLED
  76. #define HAL_GPIO_MODULE_ENABLED
  77. #define HAL_PWR_MODULE_ENABLED
  78. #define HAL_RCC_MODULE_ENABLED
  79.  
  80. /* ########################## Oscillator Values adaptation ####################*/
  81. /**
  82.   * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
  83.   *        This value is used by the RCC HAL module to compute the system frequency
  84.   *        (when HSE is used as system clock source, directly or through the PLL).
  85.   */
  86. #if !defined  (HSE_VALUE)
  87.   #define HSE_VALUE    8000000U /*!< Value of the External oscillator in Hz */
  88. #endif /* HSE_VALUE */
  89.  
  90. #if !defined  (HSE_STARTUP_TIMEOUT)
  91.   #define HSE_STARTUP_TIMEOUT    100U   /*!< Time out for HSE start up, in ms */
  92. #endif /* HSE_STARTUP_TIMEOUT */
  93.  
  94. /**
  95.   * @brief Internal High Speed oscillator (HSI) value.
  96.   *        This value is used by the RCC HAL module to compute the system frequency
  97.   *        (when HSI is used as system clock source, directly or through the PLL).
  98.   */
  99. #if !defined  (HSI_VALUE)
  100.   #define HSI_VALUE    8000000U /*!< Value of the Internal oscillator in Hz*/
  101. #endif /* HSI_VALUE */
  102.  
  103. /**
  104.   * @brief Internal Low Speed oscillator (LSI) value.
  105.   */
  106. #if !defined  (LSI_VALUE)
  107.  #define LSI_VALUE               40000U    /*!< LSI Typical Value in Hz */
  108. #endif /* LSI_VALUE */                     /*!< Value of the Internal Low Speed oscillator in Hz
  109.                                                 The real value may vary depending on the variations
  110.                                                 in voltage and temperature. */
  111.  
  112. /**
  113.   * @brief External Low Speed oscillator (LSE) value.
  114.   *        This value is used by the UART, RTC HAL module to compute the system frequency
  115.   */
  116. #if !defined  (LSE_VALUE)
  117.   #define LSE_VALUE    32768U /*!< Value of the External oscillator in Hz*/
  118. #endif /* LSE_VALUE */
  119.  
  120. #if !defined  (LSE_STARTUP_TIMEOUT)
  121.   #define LSE_STARTUP_TIMEOUT    5000U   /*!< Time out for LSE start up, in ms */
  122. #endif /* LSE_STARTUP_TIMEOUT */
  123.  
  124. /* Tip: To avoid modifying this file each time you need to use different HSE,
  125.    ===  you can define the HSE value in your toolchain compiler preprocessor. */
  126.  
  127. /* ########################### System Configuration ######################### */
  128. /**
  129.   * @brief This is the HAL system configuration section
  130.   */
  131. #define  VDD_VALUE                    3300U /*!< Value of VDD in mv */
  132. #define  TICK_INT_PRIORITY            15U    /*!< tick interrupt priority (lowest by default)  */
  133. #define  USE_RTOS                     0U
  134. #define  PREFETCH_ENABLE              1U
  135.  
  136. #define  USE_HAL_ADC_REGISTER_CALLBACKS         0U /* ADC register callback disabled       */
  137. #define  USE_HAL_CAN_REGISTER_CALLBACKS         0U /* CAN register callback disabled       */
  138. #define  USE_HAL_CEC_REGISTER_CALLBACKS         0U /* CEC register callback disabled       */
  139. #define  USE_HAL_DAC_REGISTER_CALLBACKS         0U /* DAC register callback disabled       */
  140. #define  USE_HAL_ETH_REGISTER_CALLBACKS         0U /* ETH register callback disabled       */
  141. #define  USE_HAL_HCD_REGISTER_CALLBACKS         0U /* HCD register callback disabled       */
  142. #define  USE_HAL_I2C_REGISTER_CALLBACKS         0U /* I2C register callback disabled       */
  143. #define  USE_HAL_I2S_REGISTER_CALLBACKS         0U /* I2S register callback disabled       */
  144. #define  USE_HAL_MMC_REGISTER_CALLBACKS         0U /* MMC register callback disabled       */
  145. #define  USE_HAL_NAND_REGISTER_CALLBACKS        0U /* NAND register callback disabled      */
  146. #define  USE_HAL_NOR_REGISTER_CALLBACKS         0U /* NOR register callback disabled       */
  147. #define  USE_HAL_PCCARD_REGISTER_CALLBACKS      0U /* PCCARD register callback disabled    */
  148. #define  USE_HAL_PCD_REGISTER_CALLBACKS         0U /* PCD register callback disabled       */
  149. #define  USE_HAL_RTC_REGISTER_CALLBACKS         0U /* RTC register callback disabled       */
  150. #define  USE_HAL_SD_REGISTER_CALLBACKS          0U /* SD register callback disabled        */
  151. #define  USE_HAL_SMARTCARD_REGISTER_CALLBACKS   0U /* SMARTCARD register callback disabled */
  152. #define  USE_HAL_IRDA_REGISTER_CALLBACKS        0U /* IRDA register callback disabled      */
  153. #define  USE_HAL_SRAM_REGISTER_CALLBACKS        0U /* SRAM register callback disabled      */
  154. #define  USE_HAL_SPI_REGISTER_CALLBACKS         0U /* SPI register callback disabled       */
  155. #define  USE_HAL_TIM_REGISTER_CALLBACKS         0U /* TIM register callback disabled       */
  156. #define  USE_HAL_UART_REGISTER_CALLBACKS        0U /* UART register callback disabled      */
  157. #define  USE_HAL_USART_REGISTER_CALLBACKS       0U /* USART register callback disabled     */
  158. #define  USE_HAL_WWDG_REGISTER_CALLBACKS        0U /* WWDG register callback disabled      */
  159.  
  160. /* ########################## Assert Selection ############################## */
  161. /**
  162.   * @brief Uncomment the line below to expanse the "assert_param" macro in the
  163.   *        HAL drivers code
  164.   */
  165. /* #define USE_FULL_ASSERT    1U */
  166.  
  167. /* ################## Ethernet peripheral configuration ##################### */
  168.  
  169. /* Section 1 : Ethernet peripheral configuration */
  170.  
  171. /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
  172. #define MAC_ADDR0   2U
  173. #define MAC_ADDR1   0U
  174. #define MAC_ADDR2   0U
  175. #define MAC_ADDR3   0U
  176. #define MAC_ADDR4   0U
  177. #define MAC_ADDR5   0U
  178.  
  179. /* Definition of the Ethernet driver buffers size and count */
  180. #define ETH_RX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for receive               */
  181. #define ETH_TX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for transmit              */
  182. #define ETH_RXBUFNB                    8U       /* 4 Rx buffers of size ETH_RX_BUF_SIZE  */
  183. #define ETH_TXBUFNB                    4U       /* 4 Tx buffers of size ETH_TX_BUF_SIZE  */
  184.  
  185. /* Section 2: PHY configuration section */
  186.  
  187. /* DP83848_PHY_ADDRESS Address*/
  188. #define DP83848_PHY_ADDRESS           0x01U
  189. /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
  190. #define PHY_RESET_DELAY                 0x000000FFU
  191. /* PHY Configuration delay */
  192. #define PHY_CONFIG_DELAY                0x00000FFFU
  193.  
  194. #define PHY_READ_TO                     0x0000FFFFU
  195. #define PHY_WRITE_TO                    0x0000FFFFU
  196.  
  197. /* Section 3: Common PHY Registers */
  198.  
  199. #define PHY_BCR                         ((uint16_t)0x00)    /*!< Transceiver Basic Control Register   */
  200. #define PHY_BSR                         ((uint16_t)0x01)    /*!< Transceiver Basic Status Register    */
  201.  
  202. #define PHY_RESET                       ((uint16_t)0x8000)  /*!< PHY Reset */
  203. #define PHY_LOOPBACK                    ((uint16_t)0x4000)  /*!< Select loop-back mode */
  204. #define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100)  /*!< Set the full-duplex mode at 100 Mb/s */
  205. #define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000)  /*!< Set the half-duplex mode at 100 Mb/s */
  206. #define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100)  /*!< Set the full-duplex mode at 10 Mb/s  */
  207. #define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000)  /*!< Set the half-duplex mode at 10 Mb/s  */
  208. #define PHY_AUTONEGOTIATION             ((uint16_t)0x1000)  /*!< Enable auto-negotiation function     */
  209. #define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200)  /*!< Restart auto-negotiation function    */
  210. #define PHY_POWERDOWN                   ((uint16_t)0x0800)  /*!< Select the power down mode           */
  211. #define PHY_ISOLATE                     ((uint16_t)0x0400)  /*!< Isolate PHY from MII                 */
  212.  
  213. #define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020)  /*!< Auto-Negotiation process completed   */
  214. #define PHY_LINKED_STATUS               ((uint16_t)0x0004)  /*!< Valid link established               */
  215. #define PHY_JABBER_DETECTION            ((uint16_t)0x0002)  /*!< Jabber condition detected            */
  216.  
  217. /* Section 4: Extended PHY Registers */
  218. #define PHY_SR                          ((uint16_t)0x10U)    /*!< PHY status register Offset                      */
  219.  
  220. #define PHY_SPEED_STATUS                ((uint16_t)0x0002U)  /*!< PHY Speed mask                                  */
  221. #define PHY_DUPLEX_STATUS               ((uint16_t)0x0004U)  /*!< PHY Duplex mask                                 */
  222.  
  223. /* ################## SPI peripheral configuration ########################## */
  224.  
  225. /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
  226. * Activated: CRC code is present inside driver
  227. * Deactivated: CRC code cleaned from driver
  228. */
  229.  
  230. #define USE_SPI_CRC                     0U
  231.  
  232. /* Includes ------------------------------------------------------------------*/
  233. /**
  234.   * @brief Include module's header file
  235.   */
  236.  
  237. #ifdef HAL_RCC_MODULE_ENABLED
  238. #include "stm32f1xx_hal_rcc.h"
  239. #endif /* HAL_RCC_MODULE_ENABLED */
  240.  
  241. #ifdef HAL_GPIO_MODULE_ENABLED
  242. #include "stm32f1xx_hal_gpio.h"
  243. #endif /* HAL_GPIO_MODULE_ENABLED */
  244.  
  245. #ifdef HAL_EXTI_MODULE_ENABLED
  246. #include "stm32f1xx_hal_exti.h"
  247. #endif /* HAL_EXTI_MODULE_ENABLED */
  248.  
  249. #ifdef HAL_DMA_MODULE_ENABLED
  250. #include "stm32f1xx_hal_dma.h"
  251. #endif /* HAL_DMA_MODULE_ENABLED */
  252.  
  253. #ifdef HAL_ETH_MODULE_ENABLED
  254. #include "stm32f1xx_hal_eth.h"
  255. #endif /* HAL_ETH_MODULE_ENABLED */
  256.  
  257. #ifdef HAL_CAN_MODULE_ENABLED
  258. #include "stm32f1xx_hal_can.h"
  259. #endif /* HAL_CAN_MODULE_ENABLED */
  260.  
  261. #ifdef HAL_CAN_LEGACY_MODULE_ENABLED
  262.   #include "Legacy/stm32f1xx_hal_can_legacy.h"
  263. #endif /* HAL_CAN_LEGACY_MODULE_ENABLED */
  264.  
  265. #ifdef HAL_CEC_MODULE_ENABLED
  266. #include "stm32f1xx_hal_cec.h"
  267. #endif /* HAL_CEC_MODULE_ENABLED */
  268.  
  269. #ifdef HAL_CORTEX_MODULE_ENABLED
  270. #include "stm32f1xx_hal_cortex.h"
  271. #endif /* HAL_CORTEX_MODULE_ENABLED */
  272.  
  273. #ifdef HAL_ADC_MODULE_ENABLED
  274. #include "stm32f1xx_hal_adc.h"
  275. #endif /* HAL_ADC_MODULE_ENABLED */
  276.  
  277. #ifdef HAL_CRC_MODULE_ENABLED
  278. #include "stm32f1xx_hal_crc.h"
  279. #endif /* HAL_CRC_MODULE_ENABLED */
  280.  
  281. #ifdef HAL_DAC_MODULE_ENABLED
  282. #include "stm32f1xx_hal_dac.h"
  283. #endif /* HAL_DAC_MODULE_ENABLED */
  284.  
  285. #ifdef HAL_FLASH_MODULE_ENABLED
  286. #include "stm32f1xx_hal_flash.h"
  287. #endif /* HAL_FLASH_MODULE_ENABLED */
  288.  
  289. #ifdef HAL_SRAM_MODULE_ENABLED
  290. #include "stm32f1xx_hal_sram.h"
  291. #endif /* HAL_SRAM_MODULE_ENABLED */
  292.  
  293. #ifdef HAL_NOR_MODULE_ENABLED
  294. #include "stm32f1xx_hal_nor.h"
  295. #endif /* HAL_NOR_MODULE_ENABLED */
  296.  
  297. #ifdef HAL_I2C_MODULE_ENABLED
  298. #include "stm32f1xx_hal_i2c.h"
  299. #endif /* HAL_I2C_MODULE_ENABLED */
  300.  
  301. #ifdef HAL_I2S_MODULE_ENABLED
  302. #include "stm32f1xx_hal_i2s.h"
  303. #endif /* HAL_I2S_MODULE_ENABLED */
  304.  
  305. #ifdef HAL_IWDG_MODULE_ENABLED
  306. #include "stm32f1xx_hal_iwdg.h"
  307. #endif /* HAL_IWDG_MODULE_ENABLED */
  308.  
  309. #ifdef HAL_PWR_MODULE_ENABLED
  310. #include "stm32f1xx_hal_pwr.h"
  311. #endif /* HAL_PWR_MODULE_ENABLED */
  312.  
  313. #ifdef HAL_RTC_MODULE_ENABLED
  314. #include "stm32f1xx_hal_rtc.h"
  315. #endif /* HAL_RTC_MODULE_ENABLED */
  316.  
  317. #ifdef HAL_PCCARD_MODULE_ENABLED
  318. #include "stm32f1xx_hal_pccard.h"
  319. #endif /* HAL_PCCARD_MODULE_ENABLED */
  320.  
  321. #ifdef HAL_SD_MODULE_ENABLED
  322. #include "stm32f1xx_hal_sd.h"
  323. #endif /* HAL_SD_MODULE_ENABLED */
  324.  
  325. #ifdef HAL_NAND_MODULE_ENABLED
  326. #include "stm32f1xx_hal_nand.h"
  327. #endif /* HAL_NAND_MODULE_ENABLED */
  328.  
  329. #ifdef HAL_SPI_MODULE_ENABLED
  330. #include "stm32f1xx_hal_spi.h"
  331. #endif /* HAL_SPI_MODULE_ENABLED */
  332.  
  333. #ifdef HAL_TIM_MODULE_ENABLED
  334. #include "stm32f1xx_hal_tim.h"
  335. #endif /* HAL_TIM_MODULE_ENABLED */
  336.  
  337. #ifdef HAL_UART_MODULE_ENABLED
  338. #include "stm32f1xx_hal_uart.h"
  339. #endif /* HAL_UART_MODULE_ENABLED */
  340.  
  341. #ifdef HAL_USART_MODULE_ENABLED
  342. #include "stm32f1xx_hal_usart.h"
  343. #endif /* HAL_USART_MODULE_ENABLED */
  344.  
  345. #ifdef HAL_IRDA_MODULE_ENABLED
  346. #include "stm32f1xx_hal_irda.h"
  347. #endif /* HAL_IRDA_MODULE_ENABLED */
  348.  
  349. #ifdef HAL_SMARTCARD_MODULE_ENABLED
  350. #include "stm32f1xx_hal_smartcard.h"
  351. #endif /* HAL_SMARTCARD_MODULE_ENABLED */
  352.  
  353. #ifdef HAL_WWDG_MODULE_ENABLED
  354. #include "stm32f1xx_hal_wwdg.h"
  355. #endif /* HAL_WWDG_MODULE_ENABLED */
  356.  
  357. #ifdef HAL_PCD_MODULE_ENABLED
  358. #include "stm32f1xx_hal_pcd.h"
  359. #endif /* HAL_PCD_MODULE_ENABLED */
  360.  
  361. #ifdef HAL_HCD_MODULE_ENABLED
  362. #include "stm32f1xx_hal_hcd.h"
  363. #endif /* HAL_HCD_MODULE_ENABLED */
  364.  
  365. #ifdef HAL_MMC_MODULE_ENABLED
  366. #include "stm32f1xx_hal_mmc.h"
  367. #endif /* HAL_MMC_MODULE_ENABLED */
  368.  
  369. /* Exported macro ------------------------------------------------------------*/
  370. #ifdef  USE_FULL_ASSERT
  371. /**
  372.   * @brief  The assert_param macro is used for function's parameters check.
  373.   * @param  expr If expr is false, it calls assert_failed function
  374.   *         which reports the name of the source file and the source
  375.   *         line number of the call that failed.
  376.   *         If expr is true, it returns no value.
  377.   * @retval None
  378.   */
  379. #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
  380. /* Exported functions ------------------------------------------------------- */
  381. void assert_failed(uint8_t* file, uint32_t line);
  382. #else
  383. #define assert_param(expr) ((void)0U)
  384. #endif /* USE_FULL_ASSERT */
  385.  
  386. #ifdef __cplusplus
  387. }
  388. #endif
  389.  
  390. #endif /* __STM32F1xx_HAL_CONF_H */
  391.  
  392.