Subversion Repositories LedShow

Rev

Go to most recent revision | Blame | Compare with Previous | Last modification | View Log | Download | RSS feed

  1. /**
  2.   ******************************************************************************
  3.   * @file    stm32f1xx_hal_conf.h
  4.   * @brief   HAL configuration file.
  5.   ******************************************************************************
  6.   * @attention
  7.   *
  8.   * <h2><center>&copy; COPYRIGHT(c) 2019 STMicroelectronics</center></h2>
  9.   *
  10.   * Redistribution and use in source and binary forms, with or without modification,
  11.   * are permitted provided that the following conditions are met:
  12.   *   1. Redistributions of source code must retain the above copyright notice,
  13.   *      this list of conditions and the following disclaimer.
  14.   *   2. Redistributions in binary form must reproduce the above copyright notice,
  15.   *      this list of conditions and the following disclaimer in the documentation
  16.   *      and/or other materials provided with the distribution.
  17.   *   3. Neither the name of STMicroelectronics nor the names of its contributors
  18.   *      may be used to endorse or promote products derived from this software
  19.   *      without specific prior written permission.
  20.   *
  21.   * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  22.   * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  23.   * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  24.   * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
  25.   * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
  26.   * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  27.   * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
  28.   * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
  29.   * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
  30.   * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  31.   *
  32.   ******************************************************************************
  33.   */
  34.  
  35. /* Define to prevent recursive inclusion -------------------------------------*/
  36. #ifndef __STM32F1xx_HAL_CONF_H
  37. #define __STM32F1xx_HAL_CONF_H
  38.  
  39. #ifdef __cplusplus
  40.  extern "C" {
  41. #endif
  42.  
  43. /* Exported types ------------------------------------------------------------*/
  44. /* Exported constants --------------------------------------------------------*/
  45.  
  46. /* ########################## Module Selection ############################## */
  47. /**
  48.   * @brief This is the list of modules to be used in the HAL driver
  49.   */
  50.  
  51. #define HAL_MODULE_ENABLED  
  52. /*#define HAL_ADC_MODULE_ENABLED   */
  53. /*#define HAL_CRYP_MODULE_ENABLED   */
  54. /*#define HAL_CAN_MODULE_ENABLED   */
  55. /*#define HAL_CEC_MODULE_ENABLED   */
  56. /*#define HAL_CORTEX_MODULE_ENABLED   */
  57. /*#define HAL_CRC_MODULE_ENABLED   */
  58. /*#define HAL_DAC_MODULE_ENABLED   */
  59. #define HAL_DMA_MODULE_ENABLED
  60. /*#define HAL_ETH_MODULE_ENABLED   */
  61. /*#define HAL_FLASH_MODULE_ENABLED   */
  62. #define HAL_GPIO_MODULE_ENABLED
  63. /*#define HAL_I2C_MODULE_ENABLED   */
  64. /*#define HAL_I2S_MODULE_ENABLED   */
  65. /*#define HAL_IRDA_MODULE_ENABLED   */
  66. /*#define HAL_IWDG_MODULE_ENABLED   */
  67. /*#define HAL_NOR_MODULE_ENABLED   */
  68. /*#define HAL_NAND_MODULE_ENABLED   */
  69. /*#define HAL_PCCARD_MODULE_ENABLED   */
  70. #define HAL_PCD_MODULE_ENABLED
  71. /*#define HAL_HCD_MODULE_ENABLED   */
  72. /*#define HAL_PWR_MODULE_ENABLED   */
  73. /*#define HAL_RCC_MODULE_ENABLED   */
  74. /*#define HAL_RTC_MODULE_ENABLED   */
  75. /*#define HAL_SD_MODULE_ENABLED   */
  76. /*#define HAL_MMC_MODULE_ENABLED   */
  77. /*#define HAL_SDRAM_MODULE_ENABLED   */
  78. /*#define HAL_SMARTCARD_MODULE_ENABLED   */
  79. #define HAL_SPI_MODULE_ENABLED
  80. /*#define HAL_SRAM_MODULE_ENABLED   */
  81. /*#define HAL_TIM_MODULE_ENABLED   */
  82. #define HAL_UART_MODULE_ENABLED
  83. /*#define HAL_USART_MODULE_ENABLED   */
  84. /*#define HAL_WWDG_MODULE_ENABLED   */
  85. /*#define HAL_EXTI_MODULE_ENABLED   */
  86.  
  87. #define HAL_CORTEX_MODULE_ENABLED
  88. #define HAL_DMA_MODULE_ENABLED
  89. #define HAL_FLASH_MODULE_ENABLED
  90. #define HAL_GPIO_MODULE_ENABLED
  91. #define HAL_PWR_MODULE_ENABLED
  92. #define HAL_RCC_MODULE_ENABLED
  93.  
  94. /* ########################## Oscillator Values adaptation ####################*/
  95. /**
  96.   * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
  97.   *        This value is used by the RCC HAL module to compute the system frequency
  98.   *        (when HSE is used as system clock source, directly or through the PLL).  
  99.   */
  100. #if !defined  (HSE_VALUE)
  101.   #define HSE_VALUE    ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */
  102. #endif /* HSE_VALUE */
  103.  
  104. #if !defined  (HSE_STARTUP_TIMEOUT)
  105.   #define HSE_STARTUP_TIMEOUT    ((uint32_t)100)   /*!< Time out for HSE start up, in ms */
  106. #endif /* HSE_STARTUP_TIMEOUT */
  107.  
  108. /**
  109.   * @brief Internal High Speed oscillator (HSI) value.
  110.   *        This value is used by the RCC HAL module to compute the system frequency
  111.   *        (when HSI is used as system clock source, directly or through the PLL).
  112.   */
  113. #if !defined  (HSI_VALUE)
  114.   #define HSI_VALUE    ((uint32_t)8000000) /*!< Value of the Internal oscillator in Hz*/
  115. #endif /* HSI_VALUE */
  116.  
  117. /**
  118.   * @brief Internal Low Speed oscillator (LSI) value.
  119.   */
  120. #if !defined  (LSI_VALUE)
  121.  #define LSI_VALUE               40000U    /*!< LSI Typical Value in Hz */
  122. #endif /* LSI_VALUE */                     /*!< Value of the Internal Low Speed oscillator in Hz
  123.                                                 The real value may vary depending on the variations
  124.                                                 in voltage and temperature. */
  125.  
  126. /**
  127.   * @brief External Low Speed oscillator (LSE) value.
  128.   *        This value is used by the UART, RTC HAL module to compute the system frequency
  129.   */
  130. #if !defined  (LSE_VALUE)
  131.   #define LSE_VALUE    ((uint32_t)32768) /*!< Value of the External oscillator in Hz*/
  132. #endif /* LSE_VALUE */
  133.  
  134. #if !defined  (LSE_STARTUP_TIMEOUT)
  135.   #define LSE_STARTUP_TIMEOUT    ((uint32_t)5000)   /*!< Time out for LSE start up, in ms */
  136. #endif /* LSE_STARTUP_TIMEOUT */
  137.  
  138. /* Tip: To avoid modifying this file each time you need to use different HSE,
  139.    ===  you can define the HSE value in your toolchain compiler preprocessor. */
  140.  
  141. /* ########################### System Configuration ######################### */
  142. /**
  143.   * @brief This is the HAL system configuration section
  144.   */    
  145. #define  VDD_VALUE                    ((uint32_t)3300) /*!< Value of VDD in mv */          
  146. #define  TICK_INT_PRIORITY            ((uint32_t)0)    /*!< tick interrupt priority (lowest by default)  */            
  147. #define  USE_RTOS                     0
  148. #define  PREFETCH_ENABLE              1
  149.  
  150. /* ########################## Assert Selection ############################## */
  151. /**
  152.   * @brief Uncomment the line below to expanse the "assert_param" macro in the
  153.   *        HAL drivers code
  154.   */
  155. /* #define USE_FULL_ASSERT    1U */
  156.  
  157. /* ################## Ethernet peripheral configuration ##################### */
  158.  
  159. /* Section 1 : Ethernet peripheral configuration */
  160.  
  161. /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
  162. #define MAC_ADDR0   2
  163. #define MAC_ADDR1   0
  164. #define MAC_ADDR2   0
  165. #define MAC_ADDR3   0
  166. #define MAC_ADDR4   0
  167. #define MAC_ADDR5   0
  168.  
  169. /* Definition of the Ethernet driver buffers size and count */  
  170. #define ETH_RX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for receive               */
  171. #define ETH_TX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for transmit              */
  172. #define ETH_RXBUFNB                    ((uint32_t)8)       /* 4 Rx buffers of size ETH_RX_BUF_SIZE  */
  173. #define ETH_TXBUFNB                    ((uint32_t)4)       /* 4 Tx buffers of size ETH_TX_BUF_SIZE  */
  174.  
  175. /* Section 2: PHY configuration section */
  176.  
  177. /* DP83848_PHY_ADDRESS Address*/
  178. #define DP83848_PHY_ADDRESS           0x01U
  179. /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
  180. #define PHY_RESET_DELAY                 ((uint32_t)0x000000FF)
  181. /* PHY Configuration delay */
  182. #define PHY_CONFIG_DELAY                ((uint32_t)0x00000FFF)
  183.  
  184. #define PHY_READ_TO                     ((uint32_t)0x0000FFFF)
  185. #define PHY_WRITE_TO                    ((uint32_t)0x0000FFFF)
  186.  
  187. /* Section 3: Common PHY Registers */
  188.  
  189. #define PHY_BCR                         ((uint16_t)0x00)    /*!< Transceiver Basic Control Register   */
  190. #define PHY_BSR                         ((uint16_t)0x01)    /*!< Transceiver Basic Status Register    */
  191.  
  192. #define PHY_RESET                       ((uint16_t)0x8000)  /*!< PHY Reset */
  193. #define PHY_LOOPBACK                    ((uint16_t)0x4000)  /*!< Select loop-back mode */
  194. #define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100)  /*!< Set the full-duplex mode at 100 Mb/s */
  195. #define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000)  /*!< Set the half-duplex mode at 100 Mb/s */
  196. #define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100)  /*!< Set the full-duplex mode at 10 Mb/s  */
  197. #define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000)  /*!< Set the half-duplex mode at 10 Mb/s  */
  198. #define PHY_AUTONEGOTIATION             ((uint16_t)0x1000)  /*!< Enable auto-negotiation function     */
  199. #define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200)  /*!< Restart auto-negotiation function    */
  200. #define PHY_POWERDOWN                   ((uint16_t)0x0800)  /*!< Select the power down mode           */
  201. #define PHY_ISOLATE                     ((uint16_t)0x0400)  /*!< Isolate PHY from MII                 */
  202.  
  203. #define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020)  /*!< Auto-Negotiation process completed   */
  204. #define PHY_LINKED_STATUS               ((uint16_t)0x0004)  /*!< Valid link established               */
  205. #define PHY_JABBER_DETECTION            ((uint16_t)0x0002)  /*!< Jabber condition detected            */
  206.  
  207. /* Section 4: Extended PHY Registers */
  208. #define PHY_SR                          ((uint16_t)0x10U)    /*!< PHY status register Offset                      */
  209.  
  210. #define PHY_SPEED_STATUS                ((uint16_t)0x0002U)  /*!< PHY Speed mask                                  */
  211. #define PHY_DUPLEX_STATUS               ((uint16_t)0x0004U)  /*!< PHY Duplex mask                                 */
  212.  
  213. /* Includes ------------------------------------------------------------------*/
  214. /**
  215.   * @brief Include module's header file
  216.   */
  217.  
  218. #ifdef HAL_RCC_MODULE_ENABLED
  219.  #include "stm32f1xx_hal_rcc.h"
  220. #endif /* HAL_RCC_MODULE_ENABLED */
  221.  
  222. #ifdef HAL_EXTI_MODULE_ENABLED
  223.  #include "stm32f1xx_hal_exti.h"
  224. #endif /* HAL_EXTI_MODULE_ENABLED */
  225.  
  226. #ifdef HAL_GPIO_MODULE_ENABLED
  227.  #include "stm32f1xx_hal_gpio.h"
  228. #endif /* HAL_GPIO_MODULE_ENABLED */
  229.    
  230. #ifdef HAL_DMA_MODULE_ENABLED
  231.   #include "stm32f1xx_hal_dma.h"
  232. #endif /* HAL_DMA_MODULE_ENABLED */
  233.    
  234. #ifdef HAL_ETH_MODULE_ENABLED
  235.   #include "stm32f1xx_hal_eth.h"
  236. #endif /* HAL_ETH_MODULE_ENABLED */  
  237.    
  238. #ifdef HAL_CAN_MODULE_ENABLED
  239.  #include "stm32f1xx_hal_can.h"
  240. #endif /* HAL_CAN_MODULE_ENABLED */
  241.  
  242. #ifdef HAL_CEC_MODULE_ENABLED
  243.  #include "stm32f1xx_hal_cec.h"
  244. #endif /* HAL_CEC_MODULE_ENABLED */
  245.  
  246. #ifdef HAL_CORTEX_MODULE_ENABLED
  247.  #include "stm32f1xx_hal_cortex.h"
  248. #endif /* HAL_CORTEX_MODULE_ENABLED */
  249.  
  250. #ifdef HAL_ADC_MODULE_ENABLED
  251.  #include "stm32f1xx_hal_adc.h"
  252. #endif /* HAL_ADC_MODULE_ENABLED */
  253.  
  254. #ifdef HAL_CRC_MODULE_ENABLED
  255.  #include "stm32f1xx_hal_crc.h"
  256. #endif /* HAL_CRC_MODULE_ENABLED */
  257.  
  258. #ifdef HAL_DAC_MODULE_ENABLED
  259.  #include "stm32f1xx_hal_dac.h"
  260. #endif /* HAL_DAC_MODULE_ENABLED */
  261.  
  262. #ifdef HAL_FLASH_MODULE_ENABLED
  263.  #include "stm32f1xx_hal_flash.h"
  264. #endif /* HAL_FLASH_MODULE_ENABLED */
  265.  
  266. #ifdef HAL_SRAM_MODULE_ENABLED
  267.  #include "stm32f1xx_hal_sram.h"
  268. #endif /* HAL_SRAM_MODULE_ENABLED */
  269.  
  270. #ifdef HAL_NOR_MODULE_ENABLED
  271.  #include "stm32f1xx_hal_nor.h"
  272. #endif /* HAL_NOR_MODULE_ENABLED */
  273.  
  274. #ifdef HAL_I2C_MODULE_ENABLED
  275.  #include "stm32f1xx_hal_i2c.h"
  276. #endif /* HAL_I2C_MODULE_ENABLED */
  277.  
  278. #ifdef HAL_I2S_MODULE_ENABLED
  279.  #include "stm32f1xx_hal_i2s.h"
  280. #endif /* HAL_I2S_MODULE_ENABLED */
  281.  
  282. #ifdef HAL_IWDG_MODULE_ENABLED
  283.  #include "stm32f1xx_hal_iwdg.h"
  284. #endif /* HAL_IWDG_MODULE_ENABLED */
  285.  
  286. #ifdef HAL_PWR_MODULE_ENABLED
  287.  #include "stm32f1xx_hal_pwr.h"
  288. #endif /* HAL_PWR_MODULE_ENABLED */
  289.  
  290. #ifdef HAL_RTC_MODULE_ENABLED
  291.  #include "stm32f1xx_hal_rtc.h"
  292. #endif /* HAL_RTC_MODULE_ENABLED */
  293.  
  294. #ifdef HAL_PCCARD_MODULE_ENABLED
  295.  #include "stm32f1xx_hal_pccard.h"
  296. #endif /* HAL_PCCARD_MODULE_ENABLED */
  297.  
  298. #ifdef HAL_SD_MODULE_ENABLED
  299.  #include "stm32f1xx_hal_sd.h"
  300. #endif /* HAL_SD_MODULE_ENABLED */  
  301.  
  302. #ifdef HAL_MMC_MODULE_ENABLED
  303.  #include "stm32f1xx_hal_mmc.h"
  304. #endif /* HAL_MMC_MODULE_ENABLED */
  305.  
  306. #ifdef HAL_NAND_MODULE_ENABLED
  307.  #include "stm32f1xx_hal_nand.h"
  308. #endif /* HAL_NAND_MODULE_ENABLED */    
  309.  
  310. #ifdef HAL_SPI_MODULE_ENABLED
  311.  #include "stm32f1xx_hal_spi.h"
  312. #endif /* HAL_SPI_MODULE_ENABLED */
  313.  
  314. #ifdef HAL_TIM_MODULE_ENABLED
  315.  #include "stm32f1xx_hal_tim.h"
  316. #endif /* HAL_TIM_MODULE_ENABLED */
  317.  
  318. #ifdef HAL_UART_MODULE_ENABLED
  319.  #include "stm32f1xx_hal_uart.h"
  320. #endif /* HAL_UART_MODULE_ENABLED */
  321.  
  322. #ifdef HAL_USART_MODULE_ENABLED
  323.  #include "stm32f1xx_hal_usart.h"
  324. #endif /* HAL_USART_MODULE_ENABLED */
  325.  
  326. #ifdef HAL_IRDA_MODULE_ENABLED
  327.  #include "stm32f1xx_hal_irda.h"
  328. #endif /* HAL_IRDA_MODULE_ENABLED */
  329.  
  330. #ifdef HAL_SMARTCARD_MODULE_ENABLED
  331.  #include "stm32f1xx_hal_smartcard.h"
  332. #endif /* HAL_SMARTCARD_MODULE_ENABLED */
  333.  
  334. #ifdef HAL_WWDG_MODULE_ENABLED
  335.  #include "stm32f1xx_hal_wwdg.h"
  336. #endif /* HAL_WWDG_MODULE_ENABLED */
  337.  
  338. #ifdef HAL_PCD_MODULE_ENABLED
  339.  #include "stm32f1xx_hal_pcd.h"
  340. #endif /* HAL_PCD_MODULE_ENABLED */
  341.  
  342. #ifdef HAL_HCD_MODULE_ENABLED
  343.  #include "stm32f1xx_hal_hcd.h"
  344. #endif /* HAL_HCD_MODULE_ENABLED */  
  345.    
  346.  
  347. /* Exported macro ------------------------------------------------------------*/
  348. #ifdef  USE_FULL_ASSERT
  349. /**
  350.   * @brief  The assert_param macro is used for function's parameters check.
  351.   * @param  expr: If expr is false, it calls assert_failed function
  352.   *         which reports the name of the source file and the source
  353.   *         line number of the call that failed.
  354.   *         If expr is true, it returns no value.
  355.   * @retval None
  356.   */
  357.   #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
  358. /* Exported functions ------------------------------------------------------- */
  359.   void assert_failed(uint8_t* file, uint32_t line);
  360. #else
  361.   #define assert_param(expr) ((void)0U)
  362. #endif /* USE_FULL_ASSERT */
  363.  
  364. #ifdef __cplusplus
  365. }
  366. #endif
  367.  
  368. #endif /* __STM32F1xx_HAL_CONF_H */
  369.  
  370. /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
  371.