Subversion Repositories DashDisplay

Rev

Rev 3 | Go to most recent revision | Blame | Compare with Previous | Last modification | View Log | Download | RSS feed

  1. /**
  2.   ******************************************************************************
  3.   * @file    stm32f1xx_hal_conf.h
  4.   * @brief   HAL configuration file.
  5.   ******************************************************************************
  6.   * @attention
  7.   *
  8.   * <h2><center>&copy; COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
  9.   *
  10.   * Redistribution and use in source and binary forms, with or without modification,
  11.   * are permitted provided that the following conditions are met:
  12.   *   1. Redistributions of source code must retain the above copyright notice,
  13.   *      this list of conditions and the following disclaimer.
  14.   *   2. Redistributions in binary form must reproduce the above copyright notice,
  15.   *      this list of conditions and the following disclaimer in the documentation
  16.   *      and/or other materials provided with the distribution.
  17.   *   3. Neither the name of STMicroelectronics nor the names of its contributors
  18.   *      may be used to endorse or promote products derived from this software
  19.   *      without specific prior written permission.
  20.   *
  21.   * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  22.   * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  23.   * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  24.   * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
  25.   * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
  26.   * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  27.   * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
  28.   * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
  29.   * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
  30.   * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  31.   *
  32.   ******************************************************************************
  33.   */
  34.  
  35. /* Define to prevent recursive inclusion -------------------------------------*/
  36. #ifndef __STM32F1xx_HAL_CONF_H
  37. #define __STM32F1xx_HAL_CONF_H
  38.  
  39. #ifdef __cplusplus
  40.  extern "C" {
  41. #endif
  42.  
  43. #include "mxconstants.h"
  44.  
  45. /* Exported types ------------------------------------------------------------*/
  46. /* Exported constants --------------------------------------------------------*/
  47.  
  48. /* ########################## Module Selection ############################## */
  49. /**
  50.   * @brief This is the list of modules to be used in the HAL driver
  51.   */
  52. #define HAL_MODULE_ENABLED  
  53. #define HAL_ADC_MODULE_ENABLED
  54. //#define HAL_CAN_MODULE_ENABLED  
  55. //#define HAL_CEC_MODULE_ENABLED  
  56. //#define HAL_CORTEX_MODULE_ENABLED  
  57. //#define HAL_CRC_MODULE_ENABLED  
  58. //#define HAL_DAC_MODULE_ENABLED  
  59. //#define HAL_DMA_MODULE_ENABLED  
  60. //#define HAL_ETH_MODULE_ENABLED  
  61. //#define HAL_FLASH_MODULE_ENABLED  
  62. #define HAL_GPIO_MODULE_ENABLED
  63. //#define HAL_I2C_MODULE_ENABLED  
  64. //#define HAL_I2S_MODULE_ENABLED  
  65. #define HAL_IRDA_MODULE_ENABLED
  66. //#define HAL_IWDG_MODULE_ENABLED  
  67. //#define HAL_NOR_MODULE_ENABLED  
  68. //#define HAL_NAND_MODULE_ENABLED  
  69. //#define HAL_PCCARD_MODULE_ENABLED  
  70. #define HAL_PCD_MODULE_ENABLED
  71. //#define HAL_HCD_MODULE_ENABLED  
  72. //#define HAL_PWR_MODULE_ENABLED  
  73. //#define HAL_RCC_MODULE_ENABLED  
  74. //#define HAL_RTC_MODULE_ENABLED  
  75. //#define HAL_SD_MODULE_ENABLED  
  76. //#define HAL_SDRAM_MODULE_ENABLED  
  77. //#define HAL_SMARTCARD_MODULE_ENABLED  
  78. #define HAL_SPI_MODULE_ENABLED
  79. //#define HAL_SRAM_MODULE_ENABLED  
  80. //#define HAL_TIM_MODULE_ENABLED  
  81. #define HAL_UART_MODULE_ENABLED
  82. //#define HAL_USART_MODULE_ENABLED  
  83. //#define HAL_WWDG_MODULE_ENABLED  
  84.  
  85. #define HAL_CORTEX_MODULE_ENABLED
  86. #define HAL_DMA_MODULE_ENABLED
  87. #define HAL_FLASH_MODULE_ENABLED
  88. #define HAL_GPIO_MODULE_ENABLED
  89. #define HAL_PWR_MODULE_ENABLED
  90. #define HAL_RCC_MODULE_ENABLED
  91.  
  92. /* ########################## Oscillator Values adaptation ####################*/
  93. /**
  94.   * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
  95.   *        This value is used by the RCC HAL module to compute the system frequency
  96.   *        (when HSE is used as system clock source, directly or through the PLL).  
  97.   */
  98. #if !defined  (HSE_VALUE)
  99.   #define HSE_VALUE    ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */
  100. #endif /* HSE_VALUE */
  101.  
  102. #if !defined  (HSE_STARTUP_TIMEOUT)
  103.   #define HSE_STARTUP_TIMEOUT    ((uint32_t)100)   /*!< Time out for HSE start up, in ms */
  104. #endif /* HSE_STARTUP_TIMEOUT */
  105.  
  106. /**
  107.   * @brief Internal High Speed oscillator (HSI) value.
  108.   *        This value is used by the RCC HAL module to compute the system frequency
  109.   *        (when HSI is used as system clock source, directly or through the PLL).
  110.   */
  111. #if !defined  (HSI_VALUE)
  112.   #define HSI_VALUE    ((uint32_t)8000000) /*!< Value of the Internal oscillator in Hz*/
  113. #endif /* HSI_VALUE */
  114.  
  115. /**
  116.   * @brief External Low Speed oscillator (LSE) value.
  117.   *        This value is used by the UART, RTC HAL module to compute the system frequency
  118.   */
  119. #if !defined  (LSE_VALUE)
  120.   #define LSE_VALUE    ((uint32_t)32768) /*!< Value of the External oscillator in Hz*/
  121. #endif /* LSE_VALUE */
  122.  
  123. #if !defined  (LSE_STARTUP_TIMEOUT)
  124.   #define LSE_STARTUP_TIMEOUT    ((uint32_t)5000)   /*!< Time out for LSE start up, in ms */
  125. #endif /* HSE_STARTUP_TIMEOUT */
  126.  
  127. /* Tip: To avoid modifying this file each time you need to use different HSE,
  128.    ===  you can define the HSE value in your toolchain compiler preprocessor. */
  129.  
  130. /* ########################### System Configuration ######################### */
  131. /**
  132.   * @brief This is the HAL system configuration section
  133.   */    
  134. #define  VDD_VALUE                    ((uint32_t)3300) /*!< Value of VDD in mv */          
  135. #define  TICK_INT_PRIORITY            ((uint32_t)0)    /*!< tick interrupt priority (lowest by default)  */            
  136. #define  USE_RTOS                     0
  137. #define  PREFETCH_ENABLE              1
  138.  
  139. /* ########################## Assert Selection ############################## */
  140. /**
  141.   * @brief Uncomment the line below to expanse the "assert_param" macro in the
  142.   *        HAL drivers code
  143.   */
  144. /* #define USE_FULL_ASSERT    1 */
  145.  
  146. /* ################## Ethernet peripheral configuration ##################### */
  147.  
  148. /* Section 1 : Ethernet peripheral configuration */
  149.  
  150. /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
  151. #define MAC_ADDR0   2
  152. #define MAC_ADDR1   0
  153. #define MAC_ADDR2   0
  154. #define MAC_ADDR3   0
  155. #define MAC_ADDR4   0
  156. #define MAC_ADDR5   0
  157.  
  158. /* Definition of the Ethernet driver buffers size and count */  
  159. #define ETH_RX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for receive               */
  160. #define ETH_TX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for transmit              */
  161. #define ETH_RXBUFNB                    ((uint32_t)8)       /* 4 Rx buffers of size ETH_RX_BUF_SIZE  */
  162. #define ETH_TXBUFNB                    ((uint32_t)4)       /* 4 Tx buffers of size ETH_TX_BUF_SIZE  */
  163.  
  164. /* Section 2: PHY configuration section */
  165.  
  166. /* DP83848 PHY Address*/
  167. #define DP83848_PHY_ADDRESS             0x01
  168. /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
  169. #define PHY_RESET_DELAY                 ((uint32_t)0x000000FF)
  170. /* PHY Configuration delay */
  171. #define PHY_CONFIG_DELAY                ((uint32_t)0x00000FFF)
  172.  
  173. #define PHY_READ_TO                     ((uint32_t)0x0000FFFF)
  174. #define PHY_WRITE_TO                    ((uint32_t)0x0000FFFF)
  175.  
  176. /* Section 3: Common PHY Registers */
  177.  
  178. #define PHY_BCR                         ((uint16_t)0x00)    /*!< Transceiver Basic Control Register   */
  179. #define PHY_BSR                         ((uint16_t)0x01)    /*!< Transceiver Basic Status Register    */
  180.  
  181. #define PHY_RESET                       ((uint16_t)0x8000)  /*!< PHY Reset */
  182. #define PHY_LOOPBACK                    ((uint16_t)0x4000)  /*!< Select loop-back mode */
  183. #define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100)  /*!< Set the full-duplex mode at 100 Mb/s */
  184. #define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000)  /*!< Set the half-duplex mode at 100 Mb/s */
  185. #define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100)  /*!< Set the full-duplex mode at 10 Mb/s  */
  186. #define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000)  /*!< Set the half-duplex mode at 10 Mb/s  */
  187. #define PHY_AUTONEGOTIATION             ((uint16_t)0x1000)  /*!< Enable auto-negotiation function     */
  188. #define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200)  /*!< Restart auto-negotiation function    */
  189. #define PHY_POWERDOWN                   ((uint16_t)0x0800)  /*!< Select the power down mode           */
  190. #define PHY_ISOLATE                     ((uint16_t)0x0400)  /*!< Isolate PHY from MII                 */
  191.  
  192. #define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020)  /*!< Auto-Negotiation process completed   */
  193. #define PHY_LINKED_STATUS               ((uint16_t)0x0004)  /*!< Valid link established               */
  194. #define PHY_JABBER_DETECTION            ((uint16_t)0x0002)  /*!< Jabber condition detected            */
  195.  
  196. /* Section 4: Extended PHY Registers */
  197.  
  198. #define PHY_SR                          ((uint16_t)0x10)    /*!< PHY status register Offset                      */
  199. #define PHY_MICR                        ((uint16_t)0x11)    /*!< MII Interrupt Control Register                  */
  200. #define PHY_MISR                        ((uint16_t)0x12)    /*!< MII Interrupt Status and Misc. Control Register */
  201.  
  202. #define PHY_LINK_STATUS                 ((uint16_t)0x0001)  /*!< PHY Link mask                                   */
  203. #define PHY_SPEED_STATUS                ((uint16_t)0x0002)  /*!< PHY Speed mask                                  */
  204. #define PHY_DUPLEX_STATUS               ((uint16_t)0x0004)  /*!< PHY Duplex mask                                 */
  205.  
  206. #define PHY_MICR_INT_EN                 ((uint16_t)0x0002)  /*!< PHY Enable interrupts                           */
  207. #define PHY_MICR_INT_OE                 ((uint16_t)0x0001)  /*!< PHY Enable output interrupt events              */
  208.  
  209. #define PHY_MISR_LINK_INT_EN            ((uint16_t)0x0020)  /*!< Enable Interrupt on change of link status       */
  210. #define PHY_LINK_INTERRUPT              ((uint16_t)0x2000)  /*!< PHY link status interrupt mask                  */
  211.  
  212. /* Includes ------------------------------------------------------------------*/
  213. /**
  214.   * @brief Include module's header file
  215.   */
  216.  
  217. #ifdef HAL_RCC_MODULE_ENABLED
  218.  #include "stm32f1xx_hal_rcc.h"
  219. #endif /* HAL_RCC_MODULE_ENABLED */
  220.  
  221. #ifdef HAL_GPIO_MODULE_ENABLED
  222.  #include "stm32f1xx_hal_gpio.h"
  223. #endif /* HAL_GPIO_MODULE_ENABLED */
  224.    
  225. #ifdef HAL_DMA_MODULE_ENABLED
  226.   #include "stm32f1xx_hal_dma.h"
  227. #endif /* HAL_DMA_MODULE_ENABLED */
  228.    
  229. #ifdef HAL_ETH_MODULE_ENABLED
  230.   #include "stm32f1xx_hal_eth.h"
  231. #endif /* HAL_ETH_MODULE_ENABLED */  
  232.    
  233. #ifdef HAL_CAN_MODULE_ENABLED
  234.  #include "stm32f1xx_hal_can.h"
  235. #endif /* HAL_CAN_MODULE_ENABLED */
  236.  
  237. #ifdef HAL_CEC_MODULE_ENABLED
  238.  #include "stm32f1xx_hal_cec.h"
  239. #endif /* HAL_CEC_MODULE_ENABLED */
  240.  
  241. #ifdef HAL_CORTEX_MODULE_ENABLED
  242.  #include "stm32f1xx_hal_cortex.h"
  243. #endif /* HAL_CORTEX_MODULE_ENABLED */
  244.  
  245. #ifdef HAL_ADC_MODULE_ENABLED
  246.  #include "stm32f1xx_hal_adc.h"
  247. #endif /* HAL_ADC_MODULE_ENABLED */
  248.  
  249. #ifdef HAL_CRC_MODULE_ENABLED
  250.  #include "stm32f1xx_hal_crc.h"
  251. #endif /* HAL_CRC_MODULE_ENABLED */
  252.  
  253. #ifdef HAL_DAC_MODULE_ENABLED
  254.  #include "stm32f1xx_hal_dac.h"
  255. #endif /* HAL_DAC_MODULE_ENABLED */
  256.  
  257. #ifdef HAL_FLASH_MODULE_ENABLED
  258.  #include "stm32f1xx_hal_flash.h"
  259. #endif /* HAL_FLASH_MODULE_ENABLED */
  260.  
  261. #ifdef HAL_SRAM_MODULE_ENABLED
  262.  #include "stm32f1xx_hal_sram.h"
  263. #endif /* HAL_SRAM_MODULE_ENABLED */
  264.  
  265. #ifdef HAL_NOR_MODULE_ENABLED
  266.  #include "stm32f1xx_hal_nor.h"
  267. #endif /* HAL_NOR_MODULE_ENABLED */
  268.  
  269. #ifdef HAL_I2C_MODULE_ENABLED
  270.  #include "stm32f1xx_hal_i2c.h"
  271. #endif /* HAL_I2C_MODULE_ENABLED */
  272.  
  273. #ifdef HAL_I2S_MODULE_ENABLED
  274.  #include "stm32f1xx_hal_i2s.h"
  275. #endif /* HAL_I2S_MODULE_ENABLED */
  276.  
  277. #ifdef HAL_IWDG_MODULE_ENABLED
  278.  #include "stm32f1xx_hal_iwdg.h"
  279. #endif /* HAL_IWDG_MODULE_ENABLED */
  280.  
  281. #ifdef HAL_PWR_MODULE_ENABLED
  282.  #include "stm32f1xx_hal_pwr.h"
  283. #endif /* HAL_PWR_MODULE_ENABLED */
  284.  
  285. #ifdef HAL_RTC_MODULE_ENABLED
  286.  #include "stm32f1xx_hal_rtc.h"
  287. #endif /* HAL_RTC_MODULE_ENABLED */
  288.  
  289. #ifdef HAL_PCCARD_MODULE_ENABLED
  290.  #include "stm32f1xx_hal_pccard.h"
  291. #endif /* HAL_PCCARD_MODULE_ENABLED */
  292.  
  293. #ifdef HAL_SD_MODULE_ENABLED
  294.  #include "stm32f1xx_hal_sd.h"
  295. #endif /* HAL_SD_MODULE_ENABLED */  
  296.  
  297. #ifdef HAL_NAND_MODULE_ENABLED
  298.  #include "stm32f1xx_hal_nand.h"
  299. #endif /* HAL_NAND_MODULE_ENABLED */    
  300.  
  301. #ifdef HAL_SPI_MODULE_ENABLED
  302.  #include "stm32f1xx_hal_spi.h"
  303. #endif /* HAL_SPI_MODULE_ENABLED */
  304.  
  305. #ifdef HAL_TIM_MODULE_ENABLED
  306.  #include "stm32f1xx_hal_tim.h"
  307. #endif /* HAL_TIM_MODULE_ENABLED */
  308.  
  309. #ifdef HAL_UART_MODULE_ENABLED
  310.  #include "stm32f1xx_hal_uart.h"
  311. #endif /* HAL_UART_MODULE_ENABLED */
  312.  
  313. #ifdef HAL_USART_MODULE_ENABLED
  314.  #include "stm32f1xx_hal_usart.h"
  315. #endif /* HAL_USART_MODULE_ENABLED */
  316.  
  317. #ifdef HAL_IRDA_MODULE_ENABLED
  318.  #include "stm32f1xx_hal_irda.h"
  319. #endif /* HAL_IRDA_MODULE_ENABLED */
  320.  
  321. #ifdef HAL_SMARTCARD_MODULE_ENABLED
  322.  #include "stm32f1xx_hal_smartcard.h"
  323. #endif /* HAL_SMARTCARD_MODULE_ENABLED */
  324.  
  325. #ifdef HAL_WWDG_MODULE_ENABLED
  326.  #include "stm32f1xx_hal_wwdg.h"
  327. #endif /* HAL_WWDG_MODULE_ENABLED */
  328.  
  329. #ifdef HAL_PCD_MODULE_ENABLED
  330.  #include "stm32f1xx_hal_pcd.h"
  331. #endif /* HAL_PCD_MODULE_ENABLED */
  332.  
  333. #ifdef HAL_HCD_MODULE_ENABLED
  334.  #include "stm32f1xx_hal_hcd.h"
  335. #endif /* HAL_HCD_MODULE_ENABLED */  
  336.    
  337.  
  338. /* Exported macro ------------------------------------------------------------*/
  339. #ifdef  USE_FULL_ASSERT
  340. /**
  341.   * @brief  The assert_param macro is used for function's parameters check.
  342.   * @param  expr: If expr is false, it calls assert_failed function
  343.   *         which reports the name of the source file and the source
  344.   *         line number of the call that failed.
  345.   *         If expr is true, it returns no value.
  346.   * @retval None
  347.   */
  348.   #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
  349. /* Exported functions ------------------------------------------------------- */
  350.   void assert_failed(uint8_t* file, uint32_t line);
  351. #else
  352.   #define assert_param(expr) ((void)0)
  353. #endif /* USE_FULL_ASSERT */
  354.  
  355. #ifdef __cplusplus
  356. }
  357. #endif
  358.  
  359. #endif /* __STM32F1xx_HAL_CONF_H */
  360.  
  361. /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
  362.