/**
******************************************************************************
* @file stm32f1xx_hal_pcd_ex.c
* @author MCD Application Team
* @brief PCD Extended HAL module driver.
* This file provides firmware functions to manage the following
* functionalities of the USB Peripheral Controller:
* + Extended features functions
*
******************************************************************************
* @attention
*
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
* All rights reserved.</center></h2>
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32f1xx_hal.h"
/** @addtogroup STM32F1xx_HAL_Driver
* @{
*/
/** @defgroup PCDEx PCDEx
* @brief PCD Extended HAL module driver
* @{
*/
#ifdef HAL_PCD_MODULE_ENABLED
#if defined (USB) || defined (USB_OTG_FS)
/* Private types -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private constants ---------------------------------------------------------*/
/* Private macros ------------------------------------------------------------*/
/* Private functions ---------------------------------------------------------*/
/* Exported functions --------------------------------------------------------*/
/** @defgroup PCDEx_Exported_Functions PCDEx Exported Functions
* @{
*/
/** @defgroup PCDEx_Exported_Functions_Group1 Peripheral Control functions
* @brief PCDEx control functions
*
@verbatim
===============================================================================
##### Extended features functions #####
===============================================================================
[..] This section provides functions allowing to:
(+) Update FIFO configuration
@endverbatim
* @{
*/
#if defined (USB_OTG_FS)
/**
* @brief Set Tx FIFO
* @param hpcd PCD handle
* @param fifo The number of Tx fifo
* @param size Fifo size
* @retval HAL status
*/
HAL_StatusTypeDef HAL_PCDEx_SetTxFiFo(PCD_HandleTypeDef *hpcd, uint8_t fifo, uint16_t size)
{
uint8_t i;
uint32_t Tx_Offset;
/* TXn min size = 16 words. (n : Transmit FIFO index)
When a TxFIFO is not used, the Configuration should be as follows:
case 1 : n > m and Txn is not used (n,m : Transmit FIFO indexes)
--> Txm can use the space allocated for Txn.
case2 : n < m and Txn is not used (n,m : Transmit FIFO indexes)
--> Txn should be configured with the minimum space of 16 words
The FIFO is used optimally when used TxFIFOs are allocated in the top
of the FIFO.Ex: use EP1 and EP2 as IN instead of EP1 and EP3 as IN ones.
When DMA is used 3n * FIFO locations should be reserved for internal DMA registers */
Tx_Offset = hpcd->Instance->GRXFSIZ;
if (fifo == 0U)
{
hpcd->Instance->DIEPTXF0_HNPTXFSIZ = ((uint32_t)size << 16) | Tx_Offset;
}
else
{
Tx_Offset += (hpcd->Instance->DIEPTXF0_HNPTXFSIZ) >> 16;
for (i = 0U; i < (fifo - 1U); i++)
{
Tx_Offset += (hpcd->Instance->DIEPTXF[i] >> 16);
}
/* Multiply Tx_Size by 2 to get higher performance */
hpcd->Instance->DIEPTXF[fifo - 1U] = ((uint32_t)size << 16) | Tx_Offset;
}
return HAL_OK;
}
/**
* @brief Set Rx FIFO
* @param hpcd PCD handle
* @param size Size of Rx fifo
* @retval HAL status
*/
HAL_StatusTypeDef HAL_PCDEx_SetRxFiFo(PCD_HandleTypeDef *hpcd, uint16_t size)
{
hpcd->Instance->GRXFSIZ = size;
return HAL_OK;
}
#endif /* defined (USB_OTG_FS) */
#if defined (USB)
/**
* @brief Configure PMA for EP
* @param hpcd Device instance
* @param ep_addr endpoint address
* @param ep_kind endpoint Kind
* USB_SNG_BUF: Single Buffer used
* USB_DBL_BUF: Double Buffer used
* @param pmaadress: EP address in The PMA: In case of single buffer endpoint
* this parameter is 16-bit value providing the address
* in PMA allocated to endpoint.
* In case of double buffer endpoint this parameter
* is a 32-bit value providing the endpoint buffer 0 address
* in the LSB part of 32-bit value and endpoint buffer 1 address
* in the MSB part of 32-bit value.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_PCDEx_PMAConfig(PCD_HandleTypeDef *hpcd,
uint16_t ep_addr,
uint16_t ep_kind,
uint32_t pmaadress)
{
PCD_EPTypeDef *ep;
/* initialize ep structure*/
if ((0x80U & ep_addr) == 0x80U)
{
ep = &hpcd->IN_ep[ep_addr & EP_ADDR_MSK];
}
else
{
ep = &hpcd->OUT_ep[ep_addr];
}
/* Here we check if the endpoint is single or double Buffer*/
if (ep_kind == PCD_SNG_BUF)
{
/* Single Buffer */
ep->doublebuffer = 0U;
/* Configure the PMA */
ep->pmaadress = (uint16_t)pmaadress;
}
else /* USB_DBL_BUF */
{
/* Double Buffer Endpoint */
ep->doublebuffer = 1U;
/* Configure the PMA */
ep->pmaaddr0 = (uint16_t)(pmaadress & 0xFFFFU);
ep->pmaaddr1 = (uint16_t)((pmaadress & 0xFFFF0000U) >> 16);
}
return HAL_OK;
}
/**
* @brief Software Device Connection,
* this function is not required by USB OTG FS peripheral, it is used
* only by USB Device FS peripheral.
* @param hpcd: PCD handle
* @param state: connection state (0 : disconnected / 1: connected)
* @retval None
*/
__weak void HAL_PCDEx_SetConnectionState(PCD_HandleTypeDef *hpcd, uint8_t state)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hpcd);
UNUSED(state);
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_PCDEx_SetConnectionState could be implemented in the user file
*/
}
#endif /* defined (USB) */
/**
* @brief Send LPM message to user layer callback.
* @param hpcd PCD handle
* @param msg LPM message
* @retval HAL status
*/
__weak void HAL_PCDEx_LPM_Callback(PCD_HandleTypeDef *hpcd, PCD_LPM_MsgTypeDef msg)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hpcd);
UNUSED(msg);
/* NOTE : This function should not be modified, when the callback is needed,
the HAL_PCDEx_LPM_Callback could be implemented in the user file
*/
}
/**
* @brief Send BatteryCharging message to user layer callback.
* @param hpcd PCD handle
* @param msg LPM message
* @retval HAL status
*/
__weak void HAL_PCDEx_BCD_Callback(PCD_HandleTypeDef *hpcd, PCD_BCD_MsgTypeDef msg)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hpcd);
UNUSED(msg);
/* NOTE : This function should not be modified, when the callback is needed,
the HAL_PCDEx_BCD_Callback could be implemented in the user file
*/
}
/**
* @}
*/
/**
* @}
*/
#endif /* defined (USB) || defined (USB_OTG_FS) */
#endif /* HAL_PCD_MODULE_ENABLED */
/**
* @}
*/
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/