/**
******************************************************************************
* @file stm32f1xx_ll_usb.h
* @author MCD Application Team
* @brief Header file of USB Low Layer HAL module.
******************************************************************************
* @attention
*
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
* All rights reserved.</center></h2>
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef STM32F1xx_LL_USB_H
#define STM32F1xx_LL_USB_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "stm32f1xx_hal_def.h"
#if defined (USB) || defined (USB_OTG_FS)
/** @addtogroup STM32F1xx_HAL_Driver
* @{
*/
/** @addtogroup USB_LL
* @{
*/
/* Exported types ------------------------------------------------------------*/
/**
* @brief USB Mode definition
*/
#if defined (USB_OTG_FS)
typedef enum
{
USB_DEVICE_MODE = 0,
USB_HOST_MODE = 1,
USB_DRD_MODE = 2
} USB_ModeTypeDef;
/**
* @brief URB States definition
*/
typedef enum
{
URB_IDLE = 0,
URB_DONE,
URB_NOTREADY,
URB_NYET,
URB_ERROR,
URB_STALL
} USB_OTG_URBStateTypeDef;
/**
* @brief Host channel States definition
*/
typedef enum
{
HC_IDLE = 0,
HC_XFRC,
HC_HALTED,
HC_NAK,
HC_NYET,
HC_STALL,
HC_XACTERR,
HC_BBLERR,
HC_DATATGLERR
} USB_OTG_HCStateTypeDef;
/**
* @brief USB Instance Initialization Structure definition
*/
typedef struct
{
uint32_t dev_endpoints; /*!< Device Endpoints number.
This parameter depends on the used USB core.
This parameter must be a number between Min_Data = 1 and Max_Data = 15 */
uint32_t Host_channels; /*!< Host Channels number.
This parameter Depends on the used USB core.
This parameter must be a number between Min_Data = 1 and Max_Data = 15 */
uint32_t speed; /*!< USB Core speed.
This parameter can be any value of @ref USB_Core_Speed */
uint32_t dma_enable; /*!< Enable or disable of the USB embedded DMA used only for OTG HS. */
uint32_t ep0_mps; /*!< Set the Endpoint 0 Max Packet size. */
uint32_t phy_itface; /*!< Select the used PHY interface.
This parameter can be any value of @ref USB_Core_PHY */
uint32_t Sof_enable; /*!< Enable or disable the output of the SOF signal. */
uint32_t low_power_enable; /*!< Enable or disable the low power mode. */
uint32_t lpm_enable; /*!< Enable or disable Link Power Management. */
uint32_t battery_charging_enable; /*!< Enable or disable Battery charging. */
uint32_t vbus_sensing_enable; /*!< Enable or disable the VBUS Sensing feature. */
uint32_t use_dedicated_ep1; /*!< Enable or disable the use of the dedicated EP1 interrupt. */
uint32_t use_external_vbus; /*!< Enable or disable the use of the external VBUS. */
} USB_OTG_CfgTypeDef;
typedef struct
{
uint8_t num; /*!< Endpoint number
This parameter must be a number between Min_Data = 1 and Max_Data = 15 */
uint8_t is_in; /*!< Endpoint direction
This parameter must be a number between Min_Data = 0 and Max_Data = 1 */
uint8_t is_stall; /*!< Endpoint stall condition
This parameter must be a number between Min_Data = 0 and Max_Data = 1 */
uint8_t type; /*!< Endpoint type
This parameter can be any value of @ref USB_EP_Type_ */
uint8_t data_pid_start; /*!< Initial data PID
This parameter must be a number between Min_Data = 0 and Max_Data = 1 */
uint8_t even_odd_frame; /*!< IFrame parity
This parameter must be a number between Min_Data = 0 and Max_Data = 1 */
uint16_t tx_fifo_num; /*!< Transmission FIFO number
This parameter must be a number between Min_Data = 1 and Max_Data = 15 */
uint32_t maxpacket; /*!< Endpoint Max packet size
This parameter must be a number between Min_Data = 0 and Max_Data = 64KB */
uint8_t *xfer_buff; /*!< Pointer to transfer buffer */
uint32_t dma_addr; /*!< 32 bits aligned transfer buffer address */
uint32_t xfer_len; /*!< Current transfer length */
uint32_t xfer_count; /*!< Partial transfer length in case of multi packet transfer */
} USB_OTG_EPTypeDef;
typedef struct
{
uint8_t dev_addr; /*!< USB device address.
This parameter must be a number between Min_Data = 1 and Max_Data = 255 */
uint8_t ch_num; /*!< Host channel number.
This parameter must be a number between Min_Data = 1 and Max_Data = 15 */
uint8_t ep_num; /*!< Endpoint number.
This parameter must be a number between Min_Data = 1 and Max_Data = 15 */
uint8_t ep_is_in; /*!< Endpoint direction
This parameter must be a number between Min_Data = 0 and Max_Data = 1 */
uint8_t speed; /*!< USB Host speed.
This parameter can be any value of @ref USB_Core_Speed_ */
uint8_t do_ping; /*!< Enable or disable the use of the PING protocol for HS mode. */
uint8_t process_ping; /*!< Execute the PING protocol for HS mode. */
uint8_t ep_type; /*!< Endpoint Type.
This parameter can be any value of @ref USB_EP_Type_ */
uint16_t max_packet; /*!< Endpoint Max packet size.
This parameter must be a number between Min_Data = 0 and Max_Data = 64KB */
uint8_t data_pid; /*!< Initial data PID.
This parameter must be a number between Min_Data = 0 and Max_Data = 1 */
uint8_t *xfer_buff; /*!< Pointer to transfer buffer. */
uint32_t xfer_len; /*!< Current transfer length. */
uint32_t xfer_count; /*!< Partial transfer length in case of multi packet transfer. */
uint8_t toggle_in; /*!< IN transfer current toggle flag.
This parameter must be a number between Min_Data = 0 and Max_Data = 1 */
uint8_t toggle_out; /*!< OUT transfer current toggle flag
This parameter must be a number between Min_Data = 0 and Max_Data = 1 */
uint32_t dma_addr; /*!< 32 bits aligned transfer buffer address. */
uint32_t ErrCnt; /*!< Host channel error count. */
USB_OTG_URBStateTypeDef urb_state; /*!< URB state.
This parameter can be any value of @ref USB_OTG_URBStateTypeDef */
USB_OTG_HCStateTypeDef state; /*!< Host Channel state.
This parameter can be any value of @ref USB_OTG_HCStateTypeDef */
} USB_OTG_HCTypeDef;
#endif /* defined (USB_OTG_FS) */
#if defined (USB)
typedef enum
{
USB_DEVICE_MODE = 0
} USB_ModeTypeDef;
/**
* @brief USB Initialization Structure definition
*/
typedef struct
{
uint32_t dev_endpoints; /*!< Device Endpoints number.
This parameter depends on the used USB core.
This parameter must be a number between Min_Data = 1 and Max_Data = 15 */
uint32_t speed; /*!< USB Core speed.
This parameter can be any value of @ref USB_Core_Speed */
uint32_t ep0_mps; /*!< Set the Endpoint 0 Max Packet size. */
uint32_t phy_itface; /*!< Select the used PHY interface.
This parameter can be any value of @ref USB_Core_PHY */
uint32_t Sof_enable; /*!< Enable or disable the output of the SOF signal. */
uint32_t low_power_enable; /*!< Enable or disable Low Power mode */
uint32_t lpm_enable; /*!< Enable or disable Battery charging. */
uint32_t battery_charging_enable; /*!< Enable or disable Battery charging. */
} USB_CfgTypeDef;
typedef struct
{
uint8_t num; /*!< Endpoint number
This parameter must be a number between Min_Data = 1 and Max_Data = 15 */
uint8_t is_in; /*!< Endpoint direction
This parameter must be a number between Min_Data = 0 and Max_Data = 1 */
uint8_t is_stall; /*!< Endpoint stall condition
This parameter must be a number between Min_Data = 0 and Max_Data = 1 */
uint8_t type; /*!< Endpoint type
This parameter can be any value of @ref USB_EP_Type */
uint8_t data_pid_start; /*!< Initial data PID
This parameter must be a number between Min_Data = 0 and Max_Data = 1 */
uint16_t pmaadress; /*!< PMA Address
This parameter can be any value between Min_addr = 0 and Max_addr = 1K */
uint16_t pmaaddr0; /*!< PMA Address0
This parameter can be any value between Min_addr = 0 and Max_addr = 1K */
uint16_t pmaaddr1; /*!< PMA Address1
This parameter can be any value between Min_addr = 0 and Max_addr = 1K */
uint8_t doublebuffer; /*!< Double buffer enable
This parameter can be 0 or 1 */
uint16_t tx_fifo_num; /*!< This parameter is not required by USB Device FS peripheral, it is used
only by USB OTG FS peripheral
This parameter is added to ensure compatibility across USB peripherals */
uint32_t maxpacket; /*!< Endpoint Max packet size
This parameter must be a number between Min_Data = 0 and Max_Data = 64KB */
uint8_t *xfer_buff; /*!< Pointer to transfer buffer */
uint32_t xfer_len; /*!< Current transfer length */
uint32_t xfer_count; /*!< Partial transfer length in case of multi packet transfer */
uint32_t xfer_len_db; /*!< double buffer transfer length used with bulk double buffer in */
uint8_t xfer_fill_db; /*!< double buffer Need to Fill new buffer used with bulk_in */
} USB_EPTypeDef;
#endif /* defined (USB) */
/* Exported constants --------------------------------------------------------*/
/** @defgroup PCD_Exported_Constants PCD Exported Constants
* @{
*/
#if defined (USB_OTG_FS)
/** @defgroup USB_OTG_CORE VERSION ID
* @{
*/
#define USB_OTG_CORE_ID_300A 0x4F54300AU
#define USB_OTG_CORE_ID_310A 0x4F54310AU
/**
* @}
*/
/** @defgroup USB_Core_Mode_ USB Core Mode
* @{
*/
#define USB_OTG_MODE_DEVICE 0U
#define USB_OTG_MODE_HOST 1U
#define USB_OTG_MODE_DRD 2U
/**
* @}
*/
/** @defgroup USB_LL Device Speed
* @{
*/
#define USBD_FS_SPEED 2U
#define USBH_FSLS_SPEED 1U
/**
* @}
*/
/** @defgroup USB_LL_Core_Speed USB Low Layer Core Speed
* @{
*/
#define USB_OTG_SPEED_FULL 3U
/**
* @}
*/
/** @defgroup USB_LL_Core_PHY USB Low Layer Core PHY
* @{
*/
#define USB_OTG_ULPI_PHY 1U
#define USB_OTG_EMBEDDED_PHY 2U
/**
* @}
*/
/** @defgroup USB_LL_Turnaround_Timeout Turnaround Timeout Value
* @{
*/
#ifndef USBD_FS_TRDT_VALUE
#define USBD_FS_TRDT_VALUE 5U
#define USBD_DEFAULT_TRDT_VALUE 9U
#endif /* USBD_HS_TRDT_VALUE */
/**
* @}
*/
/** @defgroup USB_LL_Core_MPS USB Low Layer Core MPS
* @{
*/
#define USB_OTG_FS_MAX_PACKET_SIZE 64U
#define USB_OTG_MAX_EP0_SIZE 64U
/**
* @}
*/
/** @defgroup USB_LL_Core_PHY_Frequency USB Low Layer Core PHY Frequency
* @{
*/
#define DSTS_ENUMSPD_HS_PHY_30MHZ_OR_60MHZ (0U << 1)
#define DSTS_ENUMSPD_FS_PHY_30MHZ_OR_60MHZ (1U << 1)
#define DSTS_ENUMSPD_FS_PHY_48MHZ (3U << 1)
/**
* @}
*/
/** @defgroup USB_LL_CORE_Frame_Interval USB Low Layer Core Frame Interval
* @{
*/
#define DCFG_FRAME_INTERVAL_80 0U
#define DCFG_FRAME_INTERVAL_85 1U
#define DCFG_FRAME_INTERVAL_90 2U
#define DCFG_FRAME_INTERVAL_95 3U
/**
* @}
*/
/** @defgroup USB_LL_EP0_MPS USB Low Layer EP0 MPS
* @{
*/
#define EP_MPS_64 0U
#define EP_MPS_32 1U
#define EP_MPS_16 2U
#define EP_MPS_8 3U
/**
* @}
*/
/** @defgroup USB_LL_EP_Speed USB Low Layer EP Speed
* @{
*/
#define EP_SPEED_LOW 0U
#define EP_SPEED_FULL 1U
#define EP_SPEED_HIGH 2U
/**
* @}
*/
/** @defgroup USB_LL_EP_Type USB Low Layer EP Type
* @{
*/
#define EP_TYPE_CTRL 0U
#define EP_TYPE_ISOC 1U
#define EP_TYPE_BULK 2U
#define EP_TYPE_INTR 3U
#define EP_TYPE_MSK 3U
/**
* @}
*/
/** @defgroup USB_LL_STS_Defines USB Low Layer STS Defines
* @{
*/
#define STS_GOUT_NAK 1U
#define STS_DATA_UPDT 2U
#define STS_XFER_COMP 3U
#define STS_SETUP_COMP 4U
#define STS_SETUP_UPDT 6U
/**
* @}
*/
/** @defgroup USB_LL_HCFG_SPEED_Defines USB Low Layer HCFG Speed Defines
* @{
*/
#define HCFG_30_60_MHZ 0U
#define HCFG_48_MHZ 1U
#define HCFG_6_MHZ 2U
/**
* @}
*/
/** @defgroup USB_LL_HPRT0_PRTSPD_SPEED_Defines USB Low Layer HPRT0 PRTSPD Speed Defines
* @{
*/
#define HPRT0_PRTSPD_HIGH_SPEED 0U
#define HPRT0_PRTSPD_FULL_SPEED 1U
#define HPRT0_PRTSPD_LOW_SPEED 2U
/**
* @}
*/
#define HCCHAR_CTRL 0U
#define HCCHAR_ISOC 1U
#define HCCHAR_BULK 2U
#define HCCHAR_INTR 3U
#define HC_PID_DATA0 0U
#define HC_PID_DATA2 1U
#define HC_PID_DATA1 2U
#define HC_PID_SETUP 3U
#define GRXSTS_PKTSTS_IN 2U
#define GRXSTS_PKTSTS_IN_XFER_COMP 3U
#define GRXSTS_PKTSTS_DATA_TOGGLE_ERR 5U
#define GRXSTS_PKTSTS_CH_HALTED 7U
#define USBx_PCGCCTL *(__IO uint32_t *)((uint32_t)USBx_BASE + USB_OTG_PCGCCTL_BASE)
#define USBx_HPRT0 *(__IO uint32_t *)((uint32_t)USBx_BASE + USB_OTG_HOST_PORT_BASE)
#define USBx_DEVICE ((USB_OTG_DeviceTypeDef *)(USBx_BASE + USB_OTG_DEVICE_BASE))
#define USBx_INEP(i) ((USB_OTG_INEndpointTypeDef *)(USBx_BASE + USB_OTG_IN_ENDPOINT_BASE + ((i) * USB_OTG_EP_REG_SIZE)))
#define USBx_OUTEP(i) ((USB_OTG_OUTEndpointTypeDef *)(USBx_BASE + USB_OTG_OUT_ENDPOINT_BASE + ((i) * USB_OTG_EP_REG_SIZE)))
#define USBx_DFIFO(i) *(__IO uint32_t *)(USBx_BASE + USB_OTG_FIFO_BASE + ((i) * USB_OTG_FIFO_SIZE))
#define USBx_HOST ((USB_OTG_HostTypeDef *)(USBx_BASE + USB_OTG_HOST_BASE))
#define USBx_HC(i) ((USB_OTG_HostChannelTypeDef *)(USBx_BASE + USB_OTG_HOST_CHANNEL_BASE + ((i) * USB_OTG_HOST_CHANNEL_SIZE)))
#endif /* defined (USB_OTG_FS) */
#if defined (USB)
/** @defgroup USB_LL_EP0_MPS USB Low Layer EP0 MPS
* @{
*/
#define EP_MPS_64 0U
#define EP_MPS_32 1U
#define EP_MPS_16 2U
#define EP_MPS_8 3U
/**
* @}
*/
/** @defgroup USB_LL_EP_Type USB Low Layer EP Type
* @{
*/
#define EP_TYPE_CTRL 0U
#define EP_TYPE_ISOC 1U
#define EP_TYPE_BULK 2U
#define EP_TYPE_INTR 3U
#define EP_TYPE_MSK 3U
/**
* @}
*/
/** @defgroup USB_LL Device Speed
* @{
*/
#define USBD_FS_SPEED 2U
/**
* @}
*/
#define BTABLE_ADDRESS 0x000U
#define PMA_ACCESS 2U
#endif /* defined (USB) */
#if defined (USB_OTG_FS)
#define EP_ADDR_MSK 0xFU
#endif /* defined (USB_OTG_FS) */
#if defined (USB)
#define EP_ADDR_MSK 0x7U
#endif /* defined (USB) */
/**
* @}
*/
/* Exported macro ------------------------------------------------------------*/
/** @defgroup USB_LL_Exported_Macros USB Low Layer Exported Macros
* @{
*/
#if defined (USB_OTG_FS)
#define USB_MASK_INTERRUPT(__INSTANCE__, __INTERRUPT__) ((__INSTANCE__)->GINTMSK &= ~(__INTERRUPT__))
#define USB_UNMASK_INTERRUPT(__INSTANCE__, __INTERRUPT__) ((__INSTANCE__)->GINTMSK |= (__INTERRUPT__))
#define CLEAR_IN_EP_INTR(__EPNUM__, __INTERRUPT__) (USBx_INEP(__EPNUM__)->DIEPINT = (__INTERRUPT__))
#define CLEAR_OUT_EP_INTR(__EPNUM__, __INTERRUPT__) (USBx_OUTEP(__EPNUM__)->DOEPINT = (__INTERRUPT__))
#endif /* defined (USB_OTG_FS) */
/**
* @}
*/
/* Exported functions --------------------------------------------------------*/
/** @addtogroup USB_LL_Exported_Functions USB Low Layer Exported Functions
* @{
*/
#if defined (USB_OTG_FS)
HAL_StatusTypeDef USB_CoreInit(USB_OTG_GlobalTypeDef *USBx, USB_OTG_CfgTypeDef cfg);
HAL_StatusTypeDef USB_DevInit(USB_OTG_GlobalTypeDef *USBx, USB_OTG_CfgTypeDef cfg);
HAL_StatusTypeDef USB_EnableGlobalInt(USB_OTG_GlobalTypeDef *USBx);
HAL_StatusTypeDef USB_DisableGlobalInt(USB_OTG_GlobalTypeDef *USBx);
HAL_StatusTypeDef USB_SetTurnaroundTime(USB_OTG_GlobalTypeDef *USBx, uint32_t hclk, uint8_t speed);
HAL_StatusTypeDef USB_SetCurrentMode(USB_OTG_GlobalTypeDef *USBx, USB_ModeTypeDef mode);
HAL_StatusTypeDef USB_SetDevSpeed(USB_OTG_GlobalTypeDef *USBx, uint8_t speed);
HAL_StatusTypeDef USB_FlushRxFifo(USB_OTG_GlobalTypeDef *USBx);
HAL_StatusTypeDef USB_FlushTxFifo(USB_OTG_GlobalTypeDef *USBx, uint32_t num);
HAL_StatusTypeDef USB_ActivateEndpoint(USB_OTG_GlobalTypeDef *USBx, USB_OTG_EPTypeDef *ep);
HAL_StatusTypeDef USB_DeactivateEndpoint(USB_OTG_GlobalTypeDef *USBx, USB_OTG_EPTypeDef *ep);
HAL_StatusTypeDef USB_ActivateDedicatedEndpoint(USB_OTG_GlobalTypeDef *USBx, USB_OTG_EPTypeDef *ep);
HAL_StatusTypeDef USB_DeactivateDedicatedEndpoint(USB_OTG_GlobalTypeDef *USBx, USB_OTG_EPTypeDef *ep);
HAL_StatusTypeDef USB_EPStartXfer(USB_OTG_GlobalTypeDef *USBx, USB_OTG_EPTypeDef *ep);
HAL_StatusTypeDef USB_EP0StartXfer(USB_OTG_GlobalTypeDef *USBx, USB_OTG_EPTypeDef *ep);
HAL_StatusTypeDef USB_WritePacket(USB_OTG_GlobalTypeDef *USBx, uint8_t *src,
uint8_t ch_ep_num, uint16_t len);
void *USB_ReadPacket(USB_OTG_GlobalTypeDef *USBx, uint8_t *dest, uint16_t len);
HAL_StatusTypeDef USB_EPSetStall(USB_OTG_GlobalTypeDef *USBx, USB_OTG_EPTypeDef *ep);
HAL_StatusTypeDef USB_EPClearStall(USB_OTG_GlobalTypeDef *USBx, USB_OTG_EPTypeDef *ep);
HAL_StatusTypeDef USB_SetDevAddress(USB_OTG_GlobalTypeDef *USBx, uint8_t address);
HAL_StatusTypeDef USB_DevConnect(USB_OTG_GlobalTypeDef *USBx);
HAL_StatusTypeDef USB_DevDisconnect(USB_OTG_GlobalTypeDef *USBx);
HAL_StatusTypeDef USB_StopDevice(USB_OTG_GlobalTypeDef *USBx);
HAL_StatusTypeDef USB_ActivateSetup(USB_OTG_GlobalTypeDef *USBx);
HAL_StatusTypeDef USB_EP0_OutStart(USB_OTG_GlobalTypeDef *USBx, uint8_t *psetup);
uint8_t USB_GetDevSpeed(USB_OTG_GlobalTypeDef *USBx);
uint32_t USB_GetMode(USB_OTG_GlobalTypeDef *USBx);
uint32_t USB_ReadInterrupts(USB_OTG_GlobalTypeDef *USBx);
uint32_t USB_ReadDevAllOutEpInterrupt(USB_OTG_GlobalTypeDef *USBx);
uint32_t USB_ReadDevOutEPInterrupt(USB_OTG_GlobalTypeDef *USBx, uint8_t epnum);
uint32_t USB_ReadDevAllInEpInterrupt(USB_OTG_GlobalTypeDef *USBx);
uint32_t USB_ReadDevInEPInterrupt(USB_OTG_GlobalTypeDef *USBx, uint8_t epnum);
void USB_ClearInterrupts(USB_OTG_GlobalTypeDef *USBx, uint32_t interrupt);
HAL_StatusTypeDef USB_HostInit(USB_OTG_GlobalTypeDef *USBx, USB_OTG_CfgTypeDef cfg);
HAL_StatusTypeDef USB_InitFSLSPClkSel(USB_OTG_GlobalTypeDef *USBx, uint8_t freq);
HAL_StatusTypeDef USB_ResetPort(USB_OTG_GlobalTypeDef *USBx);
HAL_StatusTypeDef USB_DriveVbus(USB_OTG_GlobalTypeDef *USBx, uint8_t state);
uint32_t USB_GetHostSpeed(USB_OTG_GlobalTypeDef *USBx);
uint32_t USB_GetCurrentFrame(USB_OTG_GlobalTypeDef *USBx);
HAL_StatusTypeDef USB_HC_Init(USB_OTG_GlobalTypeDef *USBx, uint8_t ch_num,
uint8_t epnum, uint8_t dev_address, uint8_t speed,
uint8_t ep_type, uint16_t mps);
HAL_StatusTypeDef USB_HC_StartXfer(USB_OTG_GlobalTypeDef *USBx,
USB_OTG_HCTypeDef *hc);
uint32_t USB_HC_ReadInterrupt(USB_OTG_GlobalTypeDef *USBx);
HAL_StatusTypeDef USB_HC_Halt(USB_OTG_GlobalTypeDef *USBx, uint8_t hc_num);
HAL_StatusTypeDef USB_DoPing(USB_OTG_GlobalTypeDef *USBx, uint8_t ch_num);
HAL_StatusTypeDef USB_StopHost(USB_OTG_GlobalTypeDef *USBx);
HAL_StatusTypeDef USB_ActivateRemoteWakeup(USB_OTG_GlobalTypeDef *USBx);
HAL_StatusTypeDef USB_DeActivateRemoteWakeup(USB_OTG_GlobalTypeDef *USBx);
#endif /* defined (USB_OTG_FS) */
#if defined (USB)
HAL_StatusTypeDef USB_CoreInit(USB_TypeDef *USBx, USB_CfgTypeDef cfg);
HAL_StatusTypeDef USB_DevInit(USB_TypeDef *USBx, USB_CfgTypeDef cfg);
HAL_StatusTypeDef USB_EnableGlobalInt(USB_TypeDef *USBx);
HAL_StatusTypeDef USB_DisableGlobalInt(USB_TypeDef *USBx);
HAL_StatusTypeDef USB_SetCurrentMode(USB_TypeDef *USBx, USB_ModeTypeDef mode);
HAL_StatusTypeDef USB_SetDevSpeed(USB_TypeDef *USBx, uint8_t speed);
HAL_StatusTypeDef USB_FlushRxFifo(USB_TypeDef *USBx);
HAL_StatusTypeDef USB_FlushTxFifo(USB_TypeDef *USBx, uint32_t num);
HAL_StatusTypeDef USB_ActivateEndpoint(USB_TypeDef *USBx, USB_EPTypeDef *ep);
HAL_StatusTypeDef USB_DeactivateEndpoint(USB_TypeDef *USBx, USB_EPTypeDef *ep);
HAL_StatusTypeDef USB_EPStartXfer(USB_TypeDef *USBx, USB_EPTypeDef *ep);
HAL_StatusTypeDef USB_EPSetStall(USB_TypeDef *USBx, USB_EPTypeDef *ep);
HAL_StatusTypeDef USB_EPClearStall(USB_TypeDef *USBx, USB_EPTypeDef *ep);
HAL_StatusTypeDef USB_SetDevAddress(USB_TypeDef *USBx, uint8_t address);
HAL_StatusTypeDef USB_DevConnect(USB_TypeDef *USBx);
HAL_StatusTypeDef USB_DevDisconnect(USB_TypeDef *USBx);
HAL_StatusTypeDef USB_StopDevice(USB_TypeDef *USBx);
HAL_StatusTypeDef USB_EP0_OutStart(USB_TypeDef *USBx, uint8_t *psetup);
HAL_StatusTypeDef USB_WritePacket(USB_TypeDef *USBx, uint8_t *src,
uint8_t ch_ep_num, uint16_t len);
void *USB_ReadPacket(USB_TypeDef *USBx, uint8_t *dest, uint16_t len);
uint32_t USB_ReadInterrupts(USB_TypeDef *USBx);
uint32_t USB_ReadDevAllOutEpInterrupt(USB_TypeDef *USBx);
uint32_t USB_ReadDevOutEPInterrupt(USB_TypeDef *USBx, uint8_t epnum);
uint32_t USB_ReadDevAllInEpInterrupt(USB_TypeDef *USBx);
uint32_t USB_ReadDevInEPInterrupt(USB_TypeDef *USBx, uint8_t epnum);
void USB_ClearInterrupts(USB_TypeDef *USBx, uint32_t interrupt);
HAL_StatusTypeDef USB_ActivateRemoteWakeup(USB_TypeDef *USBx);
HAL_StatusTypeDef USB_DeActivateRemoteWakeup(USB_TypeDef *USBx);
void USB_WritePMA(USB_TypeDef *USBx, uint8_t *pbUsrBuf,
uint16_t wPMABufAddr, uint16_t wNBytes);
void USB_ReadPMA(USB_TypeDef *USBx, uint8_t *pbUsrBuf,
uint16_t wPMABufAddr, uint16_t wNBytes);
#endif /* defined (USB) */
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#endif /* defined (USB) || defined (USB_OTG_FS) */
#ifdef __cplusplus
}
#endif
#endif /* STM32F1xx_LL_USB_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/