Subversion Repositories LedShow

Rev

Go to most recent revision | Blame | Compare with Previous | Last modification | View Log | Download | RSS feed

  1. /**
  2.   ******************************************************************************
  3.   * @file    stm32f1xx_hal_conf.h
  4.   * @author  MCD Application Team
  5.   * @brief   HAL configuration template file.
  6.   *          This file should be copied to the application folder and renamed
  7.   *          to stm32f1xx_hal_conf.h.
  8.   ******************************************************************************
  9.   * @attention
  10.   *
  11.   * <h2><center>&copy; COPYRIGHT(c) 2017 STMicroelectronics</center></h2>
  12.   *
  13.   * Redistribution and use in source and binary forms, with or without modification,
  14.   * are permitted provided that the following conditions are met:
  15.   *   1. Redistributions of source code must retain the above copyright notice,
  16.   *      this list of conditions and the following disclaimer.
  17.   *   2. Redistributions in binary form must reproduce the above copyright notice,
  18.   *      this list of conditions and the following disclaimer in the documentation
  19.   *      and/or other materials provided with the distribution.
  20.   *   3. Neither the name of STMicroelectronics nor the names of its contributors
  21.   *      may be used to endorse or promote products derived from this software
  22.   *      without specific prior written permission.
  23.   *
  24.   * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  25.   * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  26.   * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  27.   * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
  28.   * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
  29.   * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  30.   * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
  31.   * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
  32.   * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
  33.   * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  34.   *
  35.   ******************************************************************************
  36.   */
  37.  
  38. /* Define to prevent recursive inclusion -------------------------------------*/
  39. #ifndef __STM32F1xx_HAL_CONF_H
  40. #define __STM32F1xx_HAL_CONF_H
  41.  
  42. #ifdef __cplusplus
  43. extern "C" {
  44. #endif
  45.  
  46. /* Exported types ------------------------------------------------------------*/
  47. /* Exported constants --------------------------------------------------------*/
  48.  
  49. /* ########################## Module Selection ############################## */
  50. /**
  51.   * @brief This is the list of modules to be used in the HAL driver
  52.   */
  53. #define HAL_MODULE_ENABLED
  54. #define HAL_ADC_MODULE_ENABLED
  55. #define HAL_CAN_MODULE_ENABLED
  56. /* #define HAL_CAN_LEGACY_MODULE_ENABLED */
  57. #define HAL_CEC_MODULE_ENABLED
  58. #define HAL_CORTEX_MODULE_ENABLED
  59. #define HAL_CRC_MODULE_ENABLED
  60. #define HAL_DAC_MODULE_ENABLED
  61. #define HAL_DMA_MODULE_ENABLED
  62. #define HAL_ETH_MODULE_ENABLED
  63. #define HAL_FLASH_MODULE_ENABLED
  64. #define HAL_GPIO_MODULE_ENABLED
  65. #define HAL_HCD_MODULE_ENABLED
  66. #define HAL_I2C_MODULE_ENABLED
  67. #define HAL_I2S_MODULE_ENABLED
  68. #define HAL_IRDA_MODULE_ENABLED
  69. #define HAL_IWDG_MODULE_ENABLED
  70. #define HAL_NAND_MODULE_ENABLED
  71. #define HAL_NOR_MODULE_ENABLED
  72. #define HAL_PCCARD_MODULE_ENABLED
  73. #define HAL_PCD_MODULE_ENABLED
  74. #define HAL_PWR_MODULE_ENABLED
  75. #define HAL_RCC_MODULE_ENABLED
  76. #define HAL_RTC_MODULE_ENABLED
  77. #define HAL_SD_MODULE_ENABLED
  78. #define HAL_SMARTCARD_MODULE_ENABLED
  79. #define HAL_SPI_MODULE_ENABLED
  80. #define HAL_SRAM_MODULE_ENABLED
  81. #define HAL_TIM_MODULE_ENABLED
  82. #define HAL_UART_MODULE_ENABLED
  83. #define HAL_USART_MODULE_ENABLED
  84. #define HAL_WWDG_MODULE_ENABLED
  85. #define HAL_MMC_MODULE_ENABLED
  86.  
  87. /* ########################## Oscillator Values adaptation ####################*/
  88. /**
  89.   * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
  90.   *        This value is used by the RCC HAL module to compute the system frequency
  91.   *        (when HSE is used as system clock source, directly or through the PLL).
  92.   */
  93. #if !defined  (HSE_VALUE)
  94. #if defined(USE_STM3210C_EVAL)
  95. #define HSE_VALUE    25000000U /*!< Value of the External oscillator in Hz */
  96. #else
  97. #define HSE_VALUE    8000000U /*!< Value of the External oscillator in Hz */
  98. #endif
  99. #endif /* HSE_VALUE */
  100.  
  101. #if !defined  (HSE_STARTUP_TIMEOUT)
  102. #define HSE_STARTUP_TIMEOUT    100U      /*!< Time out for HSE start up, in ms */
  103. #endif /* HSE_STARTUP_TIMEOUT */
  104.  
  105. /**
  106.   * @brief Internal High Speed oscillator (HSI) value.
  107.   *        This value is used by the RCC HAL module to compute the system frequency
  108.   *        (when HSI is used as system clock source, directly or through the PLL).
  109.   */
  110. #if !defined  (HSI_VALUE)
  111. #define HSI_VALUE              8000000U  /*!< Value of the Internal oscillator in Hz */
  112. #endif /* HSI_VALUE */
  113.  
  114. /**
  115.   * @brief Internal Low Speed oscillator (LSI) value.
  116.   */
  117. #if !defined  (LSI_VALUE)
  118. #define LSI_VALUE               32000U     /*!< LSI Typical Value in Hz */
  119. #endif /* LSI_VALUE */                     /*!< Value of the Internal Low Speed oscillator in Hz
  120.                                                 The real value may vary depending on the variations
  121.                                                 in voltage and temperature. */
  122. /**
  123.   * @brief External Low Speed oscillator (LSE) value.
  124.   *        This value is used by the UART, RTC HAL module to compute the system frequency
  125.   */
  126. #if !defined  (LSE_VALUE)
  127. #define LSE_VALUE               32768U    /*!< Value of the External Low Speed oscillator in Hz */
  128. #endif /* LSE_VALUE */
  129.  
  130. #if !defined  (LSE_STARTUP_TIMEOUT)
  131. #define LSE_STARTUP_TIMEOUT    5000U     /*!< Time out for LSE start up, in ms */
  132. #endif /* LSE_STARTUP_TIMEOUT */
  133.  
  134. /* Tip: To avoid modifying this file each time you need to use different HSE,
  135.    ===  you can define the HSE value in your toolchain compiler preprocessor. */
  136.  
  137. /* ########################### System Configuration ######################### */
  138. /**
  139.   * @brief This is the HAL system configuration section
  140.   */
  141. #define  VDD_VALUE                    3300U /*!< Value of VDD in mv */
  142. #define  TICK_INT_PRIORITY            0x0FU /*!< tick interrupt priority */
  143. #define  USE_RTOS                     0U
  144. #define  PREFETCH_ENABLE              1U
  145.  
  146. /* ########################## Assert Selection ############################## */
  147. /**
  148.   * @brief Uncomment the line below to expanse the "assert_param" macro in the
  149.   *        HAL drivers code
  150.   */
  151. /* #define USE_FULL_ASSERT    1U */
  152.  
  153. /* ################## Ethernet peripheral configuration ##################### */
  154.  
  155. /* Section 1 : Ethernet peripheral configuration */
  156.  
  157. /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
  158. #define MAC_ADDR0   2U
  159. #define MAC_ADDR1   0U
  160. #define MAC_ADDR2   0U
  161. #define MAC_ADDR3   0U
  162. #define MAC_ADDR4   0U
  163. #define MAC_ADDR5   0U
  164.  
  165. /* Definition of the Ethernet driver buffers size and count */
  166. #define ETH_RX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for receive               */
  167. #define ETH_TX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for transmit              */
  168. #define ETH_RXBUFNB                    8U                  /* 8 Rx buffers of size ETH_RX_BUF_SIZE  */
  169. #define ETH_TXBUFNB                    4U                  /* 4 Tx buffers of size ETH_TX_BUF_SIZE  */
  170.  
  171. /* Section 2: PHY configuration section */
  172.  
  173. /* DP83848 PHY Address*/
  174. #define DP83848_PHY_ADDRESS             0x01U
  175. /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
  176. #define PHY_RESET_DELAY                 0x000000FFU
  177. /* PHY Configuration delay */
  178. #define PHY_CONFIG_DELAY                0x00000FFFU
  179.  
  180. #define PHY_READ_TO                     0x0000FFFFU
  181. #define PHY_WRITE_TO                    0x0000FFFFU
  182.  
  183. /* Section 3: Common PHY Registers */
  184.  
  185. #define PHY_BCR                         ((uint16_t)0x0000)  /*!< Transceiver Basic Control Register   */
  186. #define PHY_BSR                         ((uint16_t)0x0001)  /*!< Transceiver Basic Status Register    */
  187.  
  188. #define PHY_RESET                       ((uint16_t)0x8000)  /*!< PHY Reset */
  189. #define PHY_LOOPBACK                    ((uint16_t)0x4000)  /*!< Select loop-back mode */
  190. #define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100)  /*!< Set the full-duplex mode at 100 Mb/s */
  191. #define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000)  /*!< Set the half-duplex mode at 100 Mb/s */
  192. #define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100)  /*!< Set the full-duplex mode at 10 Mb/s  */
  193. #define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000)  /*!< Set the half-duplex mode at 10 Mb/s  */
  194. #define PHY_AUTONEGOTIATION             ((uint16_t)0x1000)  /*!< Enable auto-negotiation function     */
  195. #define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200)  /*!< Restart auto-negotiation function    */
  196. #define PHY_POWERDOWN                   ((uint16_t)0x0800)  /*!< Select the power down mode           */
  197. #define PHY_ISOLATE                     ((uint16_t)0x0400)  /*!< Isolate PHY from MII                 */
  198.  
  199. #define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020)  /*!< Auto-Negotiation process completed   */
  200. #define PHY_LINKED_STATUS               ((uint16_t)0x0004)  /*!< Valid link established               */
  201. #define PHY_JABBER_DETECTION            ((uint16_t)0x0002)  /*!< Jabber condition detected            */
  202.  
  203. /* Section 4: Extended PHY Registers */
  204.  
  205. #define PHY_SR                          ((uint16_t)0x0010)  /*!< PHY status register Offset                      */
  206. #define PHY_MICR                        ((uint16_t)0x0011)  /*!< MII Interrupt Control Register                  */
  207. #define PHY_MISR                        ((uint16_t)0x0012)  /*!< MII Interrupt Status and Misc. Control Register */
  208.  
  209. #define PHY_LINK_STATUS                 ((uint16_t)0x0001)  /*!< PHY Link mask                                   */
  210. #define PHY_SPEED_STATUS                ((uint16_t)0x0002)  /*!< PHY Speed mask                                  */
  211. #define PHY_DUPLEX_STATUS               ((uint16_t)0x0004)  /*!< PHY Duplex mask                                 */
  212.  
  213. #define PHY_MICR_INT_EN                 ((uint16_t)0x0002)  /*!< PHY Enable interrupts                           */
  214. #define PHY_MICR_INT_OE                 ((uint16_t)0x0001)  /*!< PHY Enable output interrupt events              */
  215.  
  216. #define PHY_MISR_LINK_INT_EN            ((uint16_t)0x0020)  /*!< Enable Interrupt on change of link status       */
  217. #define PHY_LINK_INTERRUPT              ((uint16_t)0x2000)  /*!< PHY link status interrupt mask                  */
  218.  
  219. /* ################## SPI peripheral configuration ########################## */
  220.  
  221. /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
  222. * Activated: CRC code is present inside driver
  223. * Deactivated: CRC code cleaned from driver
  224. */
  225.  
  226. #define USE_SPI_CRC                     1U
  227.  
  228. /* Includes ------------------------------------------------------------------*/
  229. /**
  230.   * @brief Include module's header file
  231.   */
  232.  
  233. #ifdef HAL_RCC_MODULE_ENABLED
  234. #include "stm32f1xx_hal_rcc.h"
  235. #endif /* HAL_RCC_MODULE_ENABLED */
  236.  
  237. #ifdef HAL_GPIO_MODULE_ENABLED
  238. #include "stm32f1xx_hal_gpio.h"
  239. #endif /* HAL_GPIO_MODULE_ENABLED */
  240.  
  241. #ifdef HAL_DMA_MODULE_ENABLED
  242. #include "stm32f1xx_hal_dma.h"
  243. #endif /* HAL_DMA_MODULE_ENABLED */
  244.  
  245. #ifdef HAL_ETH_MODULE_ENABLED
  246. #include "stm32f1xx_hal_eth.h"
  247. #endif /* HAL_ETH_MODULE_ENABLED */
  248.  
  249. #ifdef HAL_CAN_MODULE_ENABLED
  250. #include "stm32f1xx_hal_can.h"
  251. #endif /* HAL_CAN_MODULE_ENABLED */
  252.  
  253. #ifdef HAL_CAN_LEGACY_MODULE_ENABLED
  254.   #include "Legacy/stm32f1xx_hal_can_legacy.h"
  255. #endif /* HAL_CAN_LEGACY_MODULE_ENABLED */
  256.  
  257. #ifdef HAL_CEC_MODULE_ENABLED
  258. #include "stm32f1xx_hal_cec.h"
  259. #endif /* HAL_CEC_MODULE_ENABLED */
  260.  
  261. #ifdef HAL_CORTEX_MODULE_ENABLED
  262. #include "stm32f1xx_hal_cortex.h"
  263. #endif /* HAL_CORTEX_MODULE_ENABLED */
  264.  
  265. #ifdef HAL_ADC_MODULE_ENABLED
  266. #include "stm32f1xx_hal_adc.h"
  267. #endif /* HAL_ADC_MODULE_ENABLED */
  268.  
  269. #ifdef HAL_CRC_MODULE_ENABLED
  270. #include "stm32f1xx_hal_crc.h"
  271. #endif /* HAL_CRC_MODULE_ENABLED */
  272.  
  273. #ifdef HAL_DAC_MODULE_ENABLED
  274. #include "stm32f1xx_hal_dac.h"
  275. #endif /* HAL_DAC_MODULE_ENABLED */
  276.  
  277. #ifdef HAL_FLASH_MODULE_ENABLED
  278. #include "stm32f1xx_hal_flash.h"
  279. #endif /* HAL_FLASH_MODULE_ENABLED */
  280.  
  281. #ifdef HAL_SRAM_MODULE_ENABLED
  282. #include "stm32f1xx_hal_sram.h"
  283. #endif /* HAL_SRAM_MODULE_ENABLED */
  284.  
  285. #ifdef HAL_NOR_MODULE_ENABLED
  286. #include "stm32f1xx_hal_nor.h"
  287. #endif /* HAL_NOR_MODULE_ENABLED */
  288.  
  289. #ifdef HAL_I2C_MODULE_ENABLED
  290. #include "stm32f1xx_hal_i2c.h"
  291. #endif /* HAL_I2C_MODULE_ENABLED */
  292.  
  293. #ifdef HAL_I2S_MODULE_ENABLED
  294. #include "stm32f1xx_hal_i2s.h"
  295. #endif /* HAL_I2S_MODULE_ENABLED */
  296.  
  297. #ifdef HAL_IWDG_MODULE_ENABLED
  298. #include "stm32f1xx_hal_iwdg.h"
  299. #endif /* HAL_IWDG_MODULE_ENABLED */
  300.  
  301. #ifdef HAL_PWR_MODULE_ENABLED
  302. #include "stm32f1xx_hal_pwr.h"
  303. #endif /* HAL_PWR_MODULE_ENABLED */
  304.  
  305. #ifdef HAL_RTC_MODULE_ENABLED
  306. #include "stm32f1xx_hal_rtc.h"
  307. #endif /* HAL_RTC_MODULE_ENABLED */
  308.  
  309. #ifdef HAL_PCCARD_MODULE_ENABLED
  310. #include "stm32f1xx_hal_pccard.h"
  311. #endif /* HAL_PCCARD_MODULE_ENABLED */
  312.  
  313. #ifdef HAL_SD_MODULE_ENABLED
  314. #include "stm32f1xx_hal_sd.h"
  315. #endif /* HAL_SD_MODULE_ENABLED */
  316.  
  317. #ifdef HAL_NAND_MODULE_ENABLED
  318. #include "stm32f1xx_hal_nand.h"
  319. #endif /* HAL_NAND_MODULE_ENABLED */
  320.  
  321. #ifdef HAL_SPI_MODULE_ENABLED
  322. #include "stm32f1xx_hal_spi.h"
  323. #endif /* HAL_SPI_MODULE_ENABLED */
  324.  
  325. #ifdef HAL_TIM_MODULE_ENABLED
  326. #include "stm32f1xx_hal_tim.h"
  327. #endif /* HAL_TIM_MODULE_ENABLED */
  328.  
  329. #ifdef HAL_UART_MODULE_ENABLED
  330. #include "stm32f1xx_hal_uart.h"
  331. #endif /* HAL_UART_MODULE_ENABLED */
  332.  
  333. #ifdef HAL_USART_MODULE_ENABLED
  334. #include "stm32f1xx_hal_usart.h"
  335. #endif /* HAL_USART_MODULE_ENABLED */
  336.  
  337. #ifdef HAL_IRDA_MODULE_ENABLED
  338. #include "stm32f1xx_hal_irda.h"
  339. #endif /* HAL_IRDA_MODULE_ENABLED */
  340.  
  341. #ifdef HAL_SMARTCARD_MODULE_ENABLED
  342. #include "stm32f1xx_hal_smartcard.h"
  343. #endif /* HAL_SMARTCARD_MODULE_ENABLED */
  344.  
  345. #ifdef HAL_WWDG_MODULE_ENABLED
  346. #include "stm32f1xx_hal_wwdg.h"
  347. #endif /* HAL_WWDG_MODULE_ENABLED */
  348.  
  349. #ifdef HAL_PCD_MODULE_ENABLED
  350. #include "stm32f1xx_hal_pcd.h"
  351. #endif /* HAL_PCD_MODULE_ENABLED */
  352.  
  353. #ifdef HAL_HCD_MODULE_ENABLED
  354. #include "stm32f1xx_hal_hcd.h"
  355. #endif /* HAL_HCD_MODULE_ENABLED */
  356.  
  357. #ifdef HAL_MMC_MODULE_ENABLED
  358. #include "stm32f1xx_hal_mmc.h"
  359. #endif /* HAL_MMC_MODULE_ENABLED */
  360.  
  361. /* Exported macro ------------------------------------------------------------*/
  362. #ifdef  USE_FULL_ASSERT
  363. /**
  364.   * @brief  The assert_param macro is used for function's parameters check.
  365.   * @param  expr: If expr is false, it calls assert_failed function
  366.   *         which reports the name of the source file and the source
  367.   *         line number of the call that failed.
  368.   *         If expr is true, it returns no value.
  369.   * @retval None
  370.   */
  371. #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
  372. /* Exported functions ------------------------------------------------------- */
  373. void assert_failed(uint8_t *file, uint32_t line);
  374. #else
  375. #define assert_param(expr) ((void)0U)
  376. #endif /* USE_FULL_ASSERT */
  377.  
  378.  
  379. #ifdef __cplusplus
  380. }
  381. #endif
  382.  
  383. #endif /* __STM32F1xx_HAL_CONF_H */
  384.  
  385.  
  386. /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
  387.