Subversion Repositories AFRtranscoder

Rev

Blame | Last modification | View Log | Download | RSS feed

  1. /**
  2.   ******************************************************************************
  3.   * @file    stm32f1xx_hal_conf.h
  4.   * @author  MCD Application Team
  5.   * @brief   HAL configuration template file.
  6.   *          This file should be copied to the application folder and renamed
  7.   *          to stm32f1xx_hal_conf.h.
  8.   ******************************************************************************
  9.   * @attention
  10.   *
  11.   * Copyright (c) 2017 STMicroelectronics.
  12.   * All rights reserved.
  13.   *
  14.   * This software is licensed under terms that can be found in the LICENSE file
  15.   * in the root directory of this software component.
  16.   * If no LICENSE file comes with this software, it is provided AS-IS.
  17.   *
  18.   ******************************************************************************
  19.   */
  20.  
  21. /* Define to prevent recursive inclusion -------------------------------------*/
  22. #ifndef __STM32F1xx_HAL_CONF_H
  23. #define __STM32F1xx_HAL_CONF_H
  24.  
  25. #ifdef __cplusplus
  26. extern "C" {
  27. #endif
  28.  
  29. /* Exported types ------------------------------------------------------------*/
  30. /* Exported constants --------------------------------------------------------*/
  31.  
  32. /* ########################## Module Selection ############################## */
  33. /**
  34.   * @brief This is the list of modules to be used in the HAL driver
  35.   */
  36. #define HAL_MODULE_ENABLED
  37. #define HAL_ADC_MODULE_ENABLED
  38. #define HAL_CAN_MODULE_ENABLED
  39. /* #define HAL_CAN_LEGACY_MODULE_ENABLED */
  40. #define HAL_CEC_MODULE_ENABLED
  41. #define HAL_CORTEX_MODULE_ENABLED
  42. #define HAL_CRC_MODULE_ENABLED
  43. #define HAL_DAC_MODULE_ENABLED
  44. #define HAL_DMA_MODULE_ENABLED
  45. #define HAL_ETH_MODULE_ENABLED
  46. #define HAL_EXTI_MODULE_ENABLED
  47. #define HAL_FLASH_MODULE_ENABLED
  48. #define HAL_GPIO_MODULE_ENABLED
  49. #define HAL_HCD_MODULE_ENABLED
  50. #define HAL_I2C_MODULE_ENABLED
  51. #define HAL_I2S_MODULE_ENABLED
  52. #define HAL_IRDA_MODULE_ENABLED
  53. #define HAL_IWDG_MODULE_ENABLED
  54. #define HAL_NAND_MODULE_ENABLED
  55. #define HAL_NOR_MODULE_ENABLED
  56. #define HAL_PCCARD_MODULE_ENABLED
  57. #define HAL_PCD_MODULE_ENABLED
  58. #define HAL_PWR_MODULE_ENABLED
  59. #define HAL_RCC_MODULE_ENABLED
  60. #define HAL_RTC_MODULE_ENABLED
  61. #define HAL_SD_MODULE_ENABLED
  62. #define HAL_SMARTCARD_MODULE_ENABLED
  63. #define HAL_SPI_MODULE_ENABLED
  64. #define HAL_SRAM_MODULE_ENABLED
  65. #define HAL_TIM_MODULE_ENABLED
  66. #define HAL_UART_MODULE_ENABLED
  67. #define HAL_USART_MODULE_ENABLED
  68. #define HAL_WWDG_MODULE_ENABLED
  69. #define HAL_MMC_MODULE_ENABLED
  70.  
  71. /* ########################## Oscillator Values adaptation ####################*/
  72. /**
  73.   * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
  74.   *        This value is used by the RCC HAL module to compute the system frequency
  75.   *        (when HSE is used as system clock source, directly or through the PLL).
  76.   */
  77. #if !defined  (HSE_VALUE)
  78. #if defined(USE_STM3210C_EVAL)
  79. #define HSE_VALUE    25000000U /*!< Value of the External oscillator in Hz */
  80. #else
  81. #define HSE_VALUE    8000000U /*!< Value of the External oscillator in Hz */
  82. #endif
  83. #endif /* HSE_VALUE */
  84.  
  85. #if !defined  (HSE_STARTUP_TIMEOUT)
  86. #define HSE_STARTUP_TIMEOUT    100U      /*!< Time out for HSE start up, in ms */
  87. #endif /* HSE_STARTUP_TIMEOUT */
  88.  
  89. /**
  90.   * @brief Internal High Speed oscillator (HSI) value.
  91.   *        This value is used by the RCC HAL module to compute the system frequency
  92.   *        (when HSI is used as system clock source, directly or through the PLL).
  93.   */
  94. #if !defined  (HSI_VALUE)
  95. #define HSI_VALUE              8000000U  /*!< Value of the Internal oscillator in Hz */
  96. #endif /* HSI_VALUE */
  97.  
  98. /**
  99.   * @brief Internal Low Speed oscillator (LSI) value.
  100.   */
  101. #if !defined  (LSI_VALUE)
  102. #define LSI_VALUE               40000U     /*!< LSI Typical Value in Hz */
  103. #endif /* LSI_VALUE */                     /*!< Value of the Internal Low Speed oscillator in Hz
  104.                                                 The real value may vary depending on the variations
  105.                                                 in voltage and temperature. */
  106. /**
  107.   * @brief External Low Speed oscillator (LSE) value.
  108.   *        This value is used by the UART, RTC HAL module to compute the system frequency
  109.   */
  110. #if !defined  (LSE_VALUE)
  111. #define LSE_VALUE               32768U    /*!< Value of the External Low Speed oscillator in Hz */
  112. #endif /* LSE_VALUE */
  113.  
  114. #if !defined  (LSE_STARTUP_TIMEOUT)
  115. #define LSE_STARTUP_TIMEOUT    5000U     /*!< Time out for LSE start up, in ms */
  116. #endif /* LSE_STARTUP_TIMEOUT */
  117.  
  118. /* Tip: To avoid modifying this file each time you need to use different HSE,
  119.    ===  you can define the HSE value in your toolchain compiler preprocessor. */
  120.  
  121. /* ########################### System Configuration ######################### */
  122. /**
  123.   * @brief This is the HAL system configuration section
  124.   */
  125. #define  VDD_VALUE                    3300U /*!< Value of VDD in mv */
  126. #define  TICK_INT_PRIORITY            0x0FU /*!< tick interrupt priority */
  127. #define  USE_RTOS                     0U
  128. #define  PREFETCH_ENABLE              1U
  129.  
  130. #define  USE_HAL_ADC_REGISTER_CALLBACKS         0U /* ADC register callback disabled       */
  131. #define  USE_HAL_CAN_REGISTER_CALLBACKS         0U /* CAN register callback disabled       */
  132. #define  USE_HAL_CEC_REGISTER_CALLBACKS         0U /* CEC register callback disabled       */
  133. #define  USE_HAL_DAC_REGISTER_CALLBACKS         0U /* DAC register callback disabled       */
  134. #define  USE_HAL_ETH_REGISTER_CALLBACKS         0U /* ETH register callback disabled       */
  135. #define  USE_HAL_HCD_REGISTER_CALLBACKS         0U /* HCD register callback disabled       */
  136. #define  USE_HAL_I2C_REGISTER_CALLBACKS         0U /* I2C register callback disabled       */
  137. #define  USE_HAL_I2S_REGISTER_CALLBACKS         0U /* I2S register callback disabled       */
  138. #define  USE_HAL_MMC_REGISTER_CALLBACKS         0U /* MMC register callback disabled       */
  139. #define  USE_HAL_NAND_REGISTER_CALLBACKS        0U /* NAND register callback disabled      */
  140. #define  USE_HAL_NOR_REGISTER_CALLBACKS         0U /* NOR register callback disabled       */
  141. #define  USE_HAL_PCCARD_REGISTER_CALLBACKS      0U /* PCCARD register callback disabled    */
  142. #define  USE_HAL_PCD_REGISTER_CALLBACKS         0U /* PCD register callback disabled       */
  143. #define  USE_HAL_RTC_REGISTER_CALLBACKS         0U /* RTC register callback disabled       */
  144. #define  USE_HAL_SD_REGISTER_CALLBACKS          0U /* SD register callback disabled        */
  145. #define  USE_HAL_SMARTCARD_REGISTER_CALLBACKS   0U /* SMARTCARD register callback disabled */
  146. #define  USE_HAL_IRDA_REGISTER_CALLBACKS        0U /* IRDA register callback disabled      */
  147. #define  USE_HAL_SRAM_REGISTER_CALLBACKS        0U /* SRAM register callback disabled      */
  148. #define  USE_HAL_SPI_REGISTER_CALLBACKS         0U /* SPI register callback disabled       */
  149. #define  USE_HAL_TIM_REGISTER_CALLBACKS         0U /* TIM register callback disabled       */
  150. #define  USE_HAL_UART_REGISTER_CALLBACKS        0U /* UART register callback disabled      */
  151. #define  USE_HAL_USART_REGISTER_CALLBACKS       0U /* USART register callback disabled     */
  152. #define  USE_HAL_WWDG_REGISTER_CALLBACKS        0U /* WWDG register callback disabled      */
  153.  
  154. /* ########################## Assert Selection ############################## */
  155. /**
  156.   * @brief Uncomment the line below to expanse the "assert_param" macro in the
  157.   *        HAL drivers code
  158.   */
  159. /* #define USE_FULL_ASSERT    1U */
  160.  
  161. /* ################## Ethernet peripheral configuration ##################### */
  162.  
  163. /* Section 1 : Ethernet peripheral configuration */
  164.  
  165. /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
  166. #define MAC_ADDR0   2U
  167. #define MAC_ADDR1   0U
  168. #define MAC_ADDR2   0U
  169. #define MAC_ADDR3   0U
  170. #define MAC_ADDR4   0U
  171. #define MAC_ADDR5   0U
  172.  
  173. /* Definition of the Ethernet driver buffers size and count */
  174. #define ETH_RX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for receive               */
  175. #define ETH_TX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for transmit              */
  176. #define ETH_RXBUFNB                    8U                  /* 8 Rx buffers of size ETH_RX_BUF_SIZE  */
  177. #define ETH_TXBUFNB                    4U                  /* 4 Tx buffers of size ETH_TX_BUF_SIZE  */
  178.  
  179. /* Section 2: PHY configuration section */
  180.  
  181. /* DP83848 PHY Address*/
  182. #define DP83848_PHY_ADDRESS             0x01U
  183. /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
  184. #define PHY_RESET_DELAY                 0x000000FFU
  185. /* PHY Configuration delay */
  186. #define PHY_CONFIG_DELAY                0x00000FFFU
  187.  
  188. #define PHY_READ_TO                     0x0000FFFFU
  189. #define PHY_WRITE_TO                    0x0000FFFFU
  190.  
  191. /* Section 3: Common PHY Registers */
  192.  
  193. #define PHY_BCR                         ((uint16_t)0x0000)  /*!< Transceiver Basic Control Register   */
  194. #define PHY_BSR                         ((uint16_t)0x0001)  /*!< Transceiver Basic Status Register    */
  195.  
  196. #define PHY_RESET                       ((uint16_t)0x8000)  /*!< PHY Reset */
  197. #define PHY_LOOPBACK                    ((uint16_t)0x4000)  /*!< Select loop-back mode */
  198. #define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100)  /*!< Set the full-duplex mode at 100 Mb/s */
  199. #define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000)  /*!< Set the half-duplex mode at 100 Mb/s */
  200. #define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100)  /*!< Set the full-duplex mode at 10 Mb/s  */
  201. #define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000)  /*!< Set the half-duplex mode at 10 Mb/s  */
  202. #define PHY_AUTONEGOTIATION             ((uint16_t)0x1000)  /*!< Enable auto-negotiation function     */
  203. #define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200)  /*!< Restart auto-negotiation function    */
  204. #define PHY_POWERDOWN                   ((uint16_t)0x0800)  /*!< Select the power down mode           */
  205. #define PHY_ISOLATE                     ((uint16_t)0x0400)  /*!< Isolate PHY from MII                 */
  206.  
  207. #define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020)  /*!< Auto-Negotiation process completed   */
  208. #define PHY_LINKED_STATUS               ((uint16_t)0x0004)  /*!< Valid link established               */
  209. #define PHY_JABBER_DETECTION            ((uint16_t)0x0002)  /*!< Jabber condition detected            */
  210.  
  211. /* Section 4: Extended PHY Registers */
  212.  
  213. #define PHY_SR                          ((uint16_t)0x0010)  /*!< PHY status register Offset                      */
  214. #define PHY_MICR                        ((uint16_t)0x0011)  /*!< MII Interrupt Control Register                  */
  215. #define PHY_MISR                        ((uint16_t)0x0012)  /*!< MII Interrupt Status and Misc. Control Register */
  216.  
  217. #define PHY_LINK_STATUS                 ((uint16_t)0x0001)  /*!< PHY Link mask                                   */
  218. #define PHY_SPEED_STATUS                ((uint16_t)0x0002)  /*!< PHY Speed mask                                  */
  219. #define PHY_DUPLEX_STATUS               ((uint16_t)0x0004)  /*!< PHY Duplex mask                                 */
  220.  
  221. #define PHY_MICR_INT_EN                 ((uint16_t)0x0002)  /*!< PHY Enable interrupts                           */
  222. #define PHY_MICR_INT_OE                 ((uint16_t)0x0001)  /*!< PHY Enable output interrupt events              */
  223.  
  224. #define PHY_MISR_LINK_INT_EN            ((uint16_t)0x0020)  /*!< Enable Interrupt on change of link status       */
  225. #define PHY_LINK_INTERRUPT              ((uint16_t)0x2000)  /*!< PHY link status interrupt mask                  */
  226.  
  227. /* ################## SPI peripheral configuration ########################## */
  228.  
  229. /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
  230. * Activated: CRC code is present inside driver
  231. * Deactivated: CRC code cleaned from driver
  232. */
  233.  
  234. #define USE_SPI_CRC                     1U
  235.  
  236. /* Includes ------------------------------------------------------------------*/
  237. /**
  238.   * @brief Include module's header file
  239.   */
  240.  
  241. #ifdef HAL_RCC_MODULE_ENABLED
  242. #include "stm32f1xx_hal_rcc.h"
  243. #endif /* HAL_RCC_MODULE_ENABLED */
  244.  
  245. #ifdef HAL_GPIO_MODULE_ENABLED
  246. #include "stm32f1xx_hal_gpio.h"
  247. #endif /* HAL_GPIO_MODULE_ENABLED */
  248.  
  249. #ifdef HAL_EXTI_MODULE_ENABLED
  250. #include "stm32f1xx_hal_exti.h"
  251. #endif /* HAL_EXTI_MODULE_ENABLED */
  252.  
  253. #ifdef HAL_DMA_MODULE_ENABLED
  254. #include "stm32f1xx_hal_dma.h"
  255. #endif /* HAL_DMA_MODULE_ENABLED */
  256.  
  257. #ifdef HAL_ETH_MODULE_ENABLED
  258. #include "stm32f1xx_hal_eth.h"
  259. #endif /* HAL_ETH_MODULE_ENABLED */
  260.  
  261. #ifdef HAL_CAN_MODULE_ENABLED
  262. #include "stm32f1xx_hal_can.h"
  263. #endif /* HAL_CAN_MODULE_ENABLED */
  264.  
  265. #ifdef HAL_CAN_LEGACY_MODULE_ENABLED
  266.   #include "Legacy/stm32f1xx_hal_can_legacy.h"
  267. #endif /* HAL_CAN_LEGACY_MODULE_ENABLED */
  268.  
  269. #ifdef HAL_CEC_MODULE_ENABLED
  270. #include "stm32f1xx_hal_cec.h"
  271. #endif /* HAL_CEC_MODULE_ENABLED */
  272.  
  273. #ifdef HAL_CORTEX_MODULE_ENABLED
  274. #include "stm32f1xx_hal_cortex.h"
  275. #endif /* HAL_CORTEX_MODULE_ENABLED */
  276.  
  277. #ifdef HAL_ADC_MODULE_ENABLED
  278. #include "stm32f1xx_hal_adc.h"
  279. #endif /* HAL_ADC_MODULE_ENABLED */
  280.  
  281. #ifdef HAL_CRC_MODULE_ENABLED
  282. #include "stm32f1xx_hal_crc.h"
  283. #endif /* HAL_CRC_MODULE_ENABLED */
  284.  
  285. #ifdef HAL_DAC_MODULE_ENABLED
  286. #include "stm32f1xx_hal_dac.h"
  287. #endif /* HAL_DAC_MODULE_ENABLED */
  288.  
  289. #ifdef HAL_FLASH_MODULE_ENABLED
  290. #include "stm32f1xx_hal_flash.h"
  291. #endif /* HAL_FLASH_MODULE_ENABLED */
  292.  
  293. #ifdef HAL_SRAM_MODULE_ENABLED
  294. #include "stm32f1xx_hal_sram.h"
  295. #endif /* HAL_SRAM_MODULE_ENABLED */
  296.  
  297. #ifdef HAL_NOR_MODULE_ENABLED
  298. #include "stm32f1xx_hal_nor.h"
  299. #endif /* HAL_NOR_MODULE_ENABLED */
  300.  
  301. #ifdef HAL_I2C_MODULE_ENABLED
  302. #include "stm32f1xx_hal_i2c.h"
  303. #endif /* HAL_I2C_MODULE_ENABLED */
  304.  
  305. #ifdef HAL_I2S_MODULE_ENABLED
  306. #include "stm32f1xx_hal_i2s.h"
  307. #endif /* HAL_I2S_MODULE_ENABLED */
  308.  
  309. #ifdef HAL_IWDG_MODULE_ENABLED
  310. #include "stm32f1xx_hal_iwdg.h"
  311. #endif /* HAL_IWDG_MODULE_ENABLED */
  312.  
  313. #ifdef HAL_PWR_MODULE_ENABLED
  314. #include "stm32f1xx_hal_pwr.h"
  315. #endif /* HAL_PWR_MODULE_ENABLED */
  316.  
  317. #ifdef HAL_RTC_MODULE_ENABLED
  318. #include "stm32f1xx_hal_rtc.h"
  319. #endif /* HAL_RTC_MODULE_ENABLED */
  320.  
  321. #ifdef HAL_PCCARD_MODULE_ENABLED
  322. #include "stm32f1xx_hal_pccard.h"
  323. #endif /* HAL_PCCARD_MODULE_ENABLED */
  324.  
  325. #ifdef HAL_SD_MODULE_ENABLED
  326. #include "stm32f1xx_hal_sd.h"
  327. #endif /* HAL_SD_MODULE_ENABLED */
  328.  
  329. #ifdef HAL_NAND_MODULE_ENABLED
  330. #include "stm32f1xx_hal_nand.h"
  331. #endif /* HAL_NAND_MODULE_ENABLED */
  332.  
  333. #ifdef HAL_SPI_MODULE_ENABLED
  334. #include "stm32f1xx_hal_spi.h"
  335. #endif /* HAL_SPI_MODULE_ENABLED */
  336.  
  337. #ifdef HAL_TIM_MODULE_ENABLED
  338. #include "stm32f1xx_hal_tim.h"
  339. #endif /* HAL_TIM_MODULE_ENABLED */
  340.  
  341. #ifdef HAL_UART_MODULE_ENABLED
  342. #include "stm32f1xx_hal_uart.h"
  343. #endif /* HAL_UART_MODULE_ENABLED */
  344.  
  345. #ifdef HAL_USART_MODULE_ENABLED
  346. #include "stm32f1xx_hal_usart.h"
  347. #endif /* HAL_USART_MODULE_ENABLED */
  348.  
  349. #ifdef HAL_IRDA_MODULE_ENABLED
  350. #include "stm32f1xx_hal_irda.h"
  351. #endif /* HAL_IRDA_MODULE_ENABLED */
  352.  
  353. #ifdef HAL_SMARTCARD_MODULE_ENABLED
  354. #include "stm32f1xx_hal_smartcard.h"
  355. #endif /* HAL_SMARTCARD_MODULE_ENABLED */
  356.  
  357. #ifdef HAL_WWDG_MODULE_ENABLED
  358. #include "stm32f1xx_hal_wwdg.h"
  359. #endif /* HAL_WWDG_MODULE_ENABLED */
  360.  
  361. #ifdef HAL_PCD_MODULE_ENABLED
  362. #include "stm32f1xx_hal_pcd.h"
  363. #endif /* HAL_PCD_MODULE_ENABLED */
  364.  
  365. #ifdef HAL_HCD_MODULE_ENABLED
  366. #include "stm32f1xx_hal_hcd.h"
  367. #endif /* HAL_HCD_MODULE_ENABLED */
  368.  
  369. #ifdef HAL_MMC_MODULE_ENABLED
  370. #include "stm32f1xx_hal_mmc.h"
  371. #endif /* HAL_MMC_MODULE_ENABLED */
  372.  
  373. /* Exported macro ------------------------------------------------------------*/
  374. #ifdef  USE_FULL_ASSERT
  375. /**
  376.   * @brief  The assert_param macro is used for function's parameters check.
  377.   * @param  expr If expr is false, it calls assert_failed function
  378.   *         which reports the name of the source file and the source
  379.   *         line number of the call that failed.
  380.   *         If expr is true, it returns no value.
  381.   * @retval None
  382.   */
  383. #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
  384. /* Exported functions ------------------------------------------------------- */
  385. void assert_failed(uint8_t* file, uint32_t line);
  386. #else
  387. #define assert_param(expr) ((void)0U)
  388. #endif /* USE_FULL_ASSERT */
  389.  
  390.  
  391. #ifdef __cplusplus
  392. }
  393. #endif
  394.  
  395. #endif /* __STM32F1xx_HAL_CONF_H */
  396.  
  397.  
  398.  
  399.