/**
******************************************************************************
* @file stm32f0xx_hal_pwr.h
* @author MCD Application Team
* @brief Header file of PWR HAL module.
******************************************************************************
* @attention
*
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
* All rights reserved.</center></h2>
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32F0xx_HAL_PWR_H
#define __STM32F0xx_HAL_PWR_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "stm32f0xx_hal_def.h"
/** @addtogroup STM32F0xx_HAL_Driver
* @{
*/
/** @addtogroup PWR PWR
* @{
*/
/* Exported types ------------------------------------------------------------*/
/* Exported constants --------------------------------------------------------*/
/** @defgroup PWR_Exported_Constants PWR Exported Constants
* @{
*/
/** @defgroup PWR_Regulator_state_in_STOP_mode PWR Regulator state in STOP mode
* @{
*/
#define PWR_MAINREGULATOR_ON (0x00000000U)
#define PWR_LOWPOWERREGULATOR_ON PWR_CR_LPDS
#define IS_PWR_REGULATOR(REGULATOR) (((REGULATOR) == PWR_MAINREGULATOR_ON) || \
((REGULATOR) == PWR_LOWPOWERREGULATOR_ON))
/**
* @}
*/
/** @defgroup PWR_SLEEP_mode_entry PWR SLEEP mode entry
* @{
*/
#define PWR_SLEEPENTRY_WFI ((uint8_t)0x01U)
#define PWR_SLEEPENTRY_WFE ((uint8_t)0x02U)
#define IS_PWR_SLEEP_ENTRY(ENTRY) (((ENTRY) == PWR_SLEEPENTRY_WFI) || ((ENTRY) == PWR_SLEEPENTRY_WFE))
/**
* @}
*/
/** @defgroup PWR_STOP_mode_entry PWR STOP mode entry
* @{
*/
#define PWR_STOPENTRY_WFI ((uint8_t)0x01U)
#define PWR_STOPENTRY_WFE ((uint8_t)0x02U)
#define IS_PWR_STOP_ENTRY(ENTRY) (((ENTRY) == PWR_STOPENTRY_WFI) || ((ENTRY) == PWR_STOPENTRY_WFE))
/**
* @}
*/
/**
* @}
*/
/* Exported macro ------------------------------------------------------------*/
/** @defgroup PWR_Exported_Macro PWR Exported Macro
* @{
*/
/** @brief Check PWR flag is set or not.
* @param __FLAG__ specifies the flag to check.
* This parameter can be one of the following values:
* @arg PWR_FLAG_WU: Wake Up flag. This flag indicates that a wakeup event
* was received from the WKUP pin or from the RTC alarm (Alarm A),
* RTC Tamper event, RTC TimeStamp event or RTC Wakeup.
* An additional wakeup event is detected if the WKUP pin is enabled
* (by setting the EWUP bit) when the WKUP pin level is already high.
* @arg PWR_FLAG_SB: StandBy flag. This flag indicates that the system was
* resumed from StandBy mode.
* @arg PWR_FLAG_PVDO: PVD Output. This flag is valid only if PVD is enabled
* by the HAL_PWR_EnablePVD() function. The PVD is stopped by Standby mode
* For this reason, this bit is equal to 0 after Standby or reset
* until the PVDE bit is set.
* Warning: this Flag is not available on STM32F030x8 products
* @arg PWR_FLAG_VREFINTRDY: This flag indicates that the internal reference
* voltage VREFINT is ready.
* Warning: this Flag is not available on STM32F030x8 products
* @retval The new state of __FLAG__ (TRUE or FALSE).
*/
#define __HAL_PWR_GET_FLAG(__FLAG__) ((PWR->CSR & (__FLAG__)) == (__FLAG__))
/** @brief Clear the PWR's pending flags.
* @param __FLAG__ specifies the flag to clear.
* This parameter can be one of the following values:
* @arg PWR_FLAG_WU: Wake Up flag
* @arg PWR_FLAG_SB: StandBy flag
*/
#define __HAL_PWR_CLEAR_FLAG(__FLAG__) (PWR->CR |= (__FLAG__) << 2U)
/**
* @}
*/
/* Include PWR HAL Extension module */
#include "stm32f0xx_hal_pwr_ex.h"
/* Exported functions --------------------------------------------------------*/
/** @addtogroup PWR_Exported_Functions PWR Exported Functions
* @{
*/
/** @addtogroup PWR_Exported_Functions_Group1 Initialization and de-initialization functions
* @{
*/
/* Initialization and de-initialization functions *****************************/
void HAL_PWR_DeInit(void);
/**
* @}
*/
/** @addtogroup PWR_Exported_Functions_Group2 Peripheral Control functions
* @{
*/
/* Peripheral Control functions **********************************************/
void HAL_PWR_EnableBkUpAccess(void);
void HAL_PWR_DisableBkUpAccess(void);
/* WakeUp pins configuration functions ****************************************/
void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinx);
void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx);
/* Low Power modes configuration functions ************************************/
void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry);
void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry);
void HAL_PWR_EnterSTANDBYMode(void);
void HAL_PWR_EnableSleepOnExit(void);
void HAL_PWR_DisableSleepOnExit(void);
void HAL_PWR_EnableSEVOnPend(void);
void HAL_PWR_DisableSEVOnPend(void);
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* __STM32F0xx_HAL_PWR_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/