Subversion Repositories dashGPS

Rev

Go to most recent revision | Blame | Compare with Previous | Last modification | View Log | Download | RSS feed

  1. /**
  2.   ******************************************************************************
  3.   * @file    stm32f1xx_hal_conf.h
  4.   * @author  MCD Application Team
  5.   * @brief   HAL configuration template file.
  6.   *          This file should be copied to the application folder and renamed
  7.   *          to stm32f1xx_hal_conf.h.
  8.   ******************************************************************************
  9.   * @attention
  10.   *
  11.   * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
  12.   * All rights reserved.</center></h2>
  13.   *
  14.   * This software component is licensed by ST under BSD 3-Clause license,
  15.   * the "License"; You may not use this file except in compliance with the
  16.   * License. You may obtain a copy of the License at:
  17.   *                        opensource.org/licenses/BSD-3-Clause
  18.   *
  19.   ******************************************************************************
  20.   */
  21.  
  22. /* Define to prevent recursive inclusion -------------------------------------*/
  23. #ifndef __STM32F1xx_HAL_CONF_H
  24. #define __STM32F1xx_HAL_CONF_H
  25.  
  26. #ifdef __cplusplus
  27. extern "C" {
  28. #endif
  29.  
  30. /* Exported types ------------------------------------------------------------*/
  31. /* Exported constants --------------------------------------------------------*/
  32.  
  33. /* ########################## Module Selection ############################## */
  34. /**
  35.   * @brief This is the list of modules to be used in the HAL driver
  36.   */
  37. #define HAL_MODULE_ENABLED
  38. #define HAL_ADC_MODULE_ENABLED
  39. #define HAL_CAN_MODULE_ENABLED
  40. /* #define HAL_CAN_LEGACY_MODULE_ENABLED */
  41. #define HAL_CEC_MODULE_ENABLED
  42. #define HAL_CORTEX_MODULE_ENABLED
  43. #define HAL_CRC_MODULE_ENABLED
  44. #define HAL_DAC_MODULE_ENABLED
  45. #define HAL_DMA_MODULE_ENABLED
  46. #define HAL_ETH_MODULE_ENABLED
  47. #define HAL_EXTI_MODULE_ENABLED
  48. #define HAL_FLASH_MODULE_ENABLED
  49. #define HAL_GPIO_MODULE_ENABLED
  50. #define HAL_HCD_MODULE_ENABLED
  51. #define HAL_I2C_MODULE_ENABLED
  52. #define HAL_I2S_MODULE_ENABLED
  53. #define HAL_IRDA_MODULE_ENABLED
  54. #define HAL_IWDG_MODULE_ENABLED
  55. #define HAL_NAND_MODULE_ENABLED
  56. #define HAL_NOR_MODULE_ENABLED
  57. #define HAL_PCCARD_MODULE_ENABLED
  58. #define HAL_PCD_MODULE_ENABLED
  59. #define HAL_PWR_MODULE_ENABLED
  60. #define HAL_RCC_MODULE_ENABLED
  61. #define HAL_RTC_MODULE_ENABLED
  62. #define HAL_SD_MODULE_ENABLED
  63. #define HAL_SMARTCARD_MODULE_ENABLED
  64. #define HAL_SPI_MODULE_ENABLED
  65. #define HAL_SRAM_MODULE_ENABLED
  66. #define HAL_TIM_MODULE_ENABLED
  67. #define HAL_UART_MODULE_ENABLED
  68. #define HAL_USART_MODULE_ENABLED
  69. #define HAL_WWDG_MODULE_ENABLED
  70. #define HAL_MMC_MODULE_ENABLED
  71.  
  72. /* ########################## Oscillator Values adaptation ####################*/
  73. /**
  74.   * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
  75.   *        This value is used by the RCC HAL module to compute the system frequency
  76.   *        (when HSE is used as system clock source, directly or through the PLL).
  77.   */
  78. #if !defined  (HSE_VALUE)
  79. #if defined(USE_STM3210C_EVAL)
  80. #define HSE_VALUE    25000000U /*!< Value of the External oscillator in Hz */
  81. #else
  82. #define HSE_VALUE    8000000U /*!< Value of the External oscillator in Hz */
  83. #endif
  84. #endif /* HSE_VALUE */
  85.  
  86. #if !defined  (HSE_STARTUP_TIMEOUT)
  87. #define HSE_STARTUP_TIMEOUT    100U      /*!< Time out for HSE start up, in ms */
  88. #endif /* HSE_STARTUP_TIMEOUT */
  89.  
  90. /**
  91.   * @brief Internal High Speed oscillator (HSI) value.
  92.   *        This value is used by the RCC HAL module to compute the system frequency
  93.   *        (when HSI is used as system clock source, directly or through the PLL).
  94.   */
  95. #if !defined  (HSI_VALUE)
  96. #define HSI_VALUE              8000000U  /*!< Value of the Internal oscillator in Hz */
  97. #endif /* HSI_VALUE */
  98.  
  99. /**
  100.   * @brief Internal Low Speed oscillator (LSI) value.
  101.   */
  102. #if !defined  (LSI_VALUE)
  103. #define LSI_VALUE               40000U     /*!< LSI Typical Value in Hz */
  104. #endif /* LSI_VALUE */                     /*!< Value of the Internal Low Speed oscillator in Hz
  105.                                                 The real value may vary depending on the variations
  106.                                                 in voltage and temperature. */
  107. /**
  108.   * @brief External Low Speed oscillator (LSE) value.
  109.   *        This value is used by the UART, RTC HAL module to compute the system frequency
  110.   */
  111. #if !defined  (LSE_VALUE)
  112. #define LSE_VALUE               32768U    /*!< Value of the External Low Speed oscillator in Hz */
  113. #endif /* LSE_VALUE */
  114.  
  115. #if !defined  (LSE_STARTUP_TIMEOUT)
  116. #define LSE_STARTUP_TIMEOUT    5000U     /*!< Time out for LSE start up, in ms */
  117. #endif /* LSE_STARTUP_TIMEOUT */
  118.  
  119. /* Tip: To avoid modifying this file each time you need to use different HSE,
  120.    ===  you can define the HSE value in your toolchain compiler preprocessor. */
  121.  
  122. /* ########################### System Configuration ######################### */
  123. /**
  124.   * @brief This is the HAL system configuration section
  125.   */
  126. #define  VDD_VALUE                    3300U /*!< Value of VDD in mv */
  127. #define  TICK_INT_PRIORITY            0x0FU /*!< tick interrupt priority */
  128. #define  USE_RTOS                     0U
  129. #define  PREFETCH_ENABLE              1U
  130.  
  131. #define  USE_HAL_ADC_REGISTER_CALLBACKS         0U /* ADC register callback disabled       */
  132. #define  USE_HAL_CAN_REGISTER_CALLBACKS         0U /* CAN register callback disabled       */
  133. #define  USE_HAL_CEC_REGISTER_CALLBACKS         0U /* CEC register callback disabled       */
  134. #define  USE_HAL_DAC_REGISTER_CALLBACKS         0U /* DAC register callback disabled       */
  135. #define  USE_HAL_ETH_REGISTER_CALLBACKS         0U /* ETH register callback disabled       */
  136. #define  USE_HAL_HCD_REGISTER_CALLBACKS         0U /* HCD register callback disabled       */
  137. #define  USE_HAL_I2C_REGISTER_CALLBACKS         0U /* I2C register callback disabled       */
  138. #define  USE_HAL_I2S_REGISTER_CALLBACKS         0U /* I2S register callback disabled       */
  139. #define  USE_HAL_MMC_REGISTER_CALLBACKS         0U /* MMC register callback disabled       */
  140. #define  USE_HAL_NAND_REGISTER_CALLBACKS        0U /* NAND register callback disabled      */
  141. #define  USE_HAL_NOR_REGISTER_CALLBACKS         0U /* NOR register callback disabled       */
  142. #define  USE_HAL_PCCARD_REGISTER_CALLBACKS      0U /* PCCARD register callback disabled    */
  143. #define  USE_HAL_PCD_REGISTER_CALLBACKS         0U /* PCD register callback disabled       */
  144. #define  USE_HAL_RTC_REGISTER_CALLBACKS         0U /* RTC register callback disabled       */
  145. #define  USE_HAL_SD_REGISTER_CALLBACKS          0U /* SD register callback disabled        */
  146. #define  USE_HAL_SMARTCARD_REGISTER_CALLBACKS   0U /* SMARTCARD register callback disabled */
  147. #define  USE_HAL_IRDA_REGISTER_CALLBACKS        0U /* IRDA register callback disabled      */
  148. #define  USE_HAL_SRAM_REGISTER_CALLBACKS        0U /* SRAM register callback disabled      */
  149. #define  USE_HAL_SPI_REGISTER_CALLBACKS         0U /* SPI register callback disabled       */
  150. #define  USE_HAL_TIM_REGISTER_CALLBACKS         0U /* TIM register callback disabled       */
  151. #define  USE_HAL_UART_REGISTER_CALLBACKS        0U /* UART register callback disabled      */
  152. #define  USE_HAL_USART_REGISTER_CALLBACKS       0U /* USART register callback disabled     */
  153. #define  USE_HAL_WWDG_REGISTER_CALLBACKS        0U /* WWDG register callback disabled      */
  154.  
  155. /* ########################## Assert Selection ############################## */
  156. /**
  157.   * @brief Uncomment the line below to expanse the "assert_param" macro in the
  158.   *        HAL drivers code
  159.   */
  160. /* #define USE_FULL_ASSERT    1U */
  161.  
  162. /* ################## Ethernet peripheral configuration ##################### */
  163.  
  164. /* Section 1 : Ethernet peripheral configuration */
  165.  
  166. /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
  167. #define MAC_ADDR0   2U
  168. #define MAC_ADDR1   0U
  169. #define MAC_ADDR2   0U
  170. #define MAC_ADDR3   0U
  171. #define MAC_ADDR4   0U
  172. #define MAC_ADDR5   0U
  173.  
  174. /* Definition of the Ethernet driver buffers size and count */
  175. #define ETH_RX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for receive               */
  176. #define ETH_TX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for transmit              */
  177. #define ETH_RXBUFNB                    8U                  /* 8 Rx buffers of size ETH_RX_BUF_SIZE  */
  178. #define ETH_TXBUFNB                    4U                  /* 4 Tx buffers of size ETH_TX_BUF_SIZE  */
  179.  
  180. /* Section 2: PHY configuration section */
  181.  
  182. /* DP83848 PHY Address*/
  183. #define DP83848_PHY_ADDRESS             0x01U
  184. /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
  185. #define PHY_RESET_DELAY                 0x000000FFU
  186. /* PHY Configuration delay */
  187. #define PHY_CONFIG_DELAY                0x00000FFFU
  188.  
  189. #define PHY_READ_TO                     0x0000FFFFU
  190. #define PHY_WRITE_TO                    0x0000FFFFU
  191.  
  192. /* Section 3: Common PHY Registers */
  193.  
  194. #define PHY_BCR                         ((uint16_t)0x0000)  /*!< Transceiver Basic Control Register   */
  195. #define PHY_BSR                         ((uint16_t)0x0001)  /*!< Transceiver Basic Status Register    */
  196.  
  197. #define PHY_RESET                       ((uint16_t)0x8000)  /*!< PHY Reset */
  198. #define PHY_LOOPBACK                    ((uint16_t)0x4000)  /*!< Select loop-back mode */
  199. #define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100)  /*!< Set the full-duplex mode at 100 Mb/s */
  200. #define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000)  /*!< Set the half-duplex mode at 100 Mb/s */
  201. #define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100)  /*!< Set the full-duplex mode at 10 Mb/s  */
  202. #define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000)  /*!< Set the half-duplex mode at 10 Mb/s  */
  203. #define PHY_AUTONEGOTIATION             ((uint16_t)0x1000)  /*!< Enable auto-negotiation function     */
  204. #define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200)  /*!< Restart auto-negotiation function    */
  205. #define PHY_POWERDOWN                   ((uint16_t)0x0800)  /*!< Select the power down mode           */
  206. #define PHY_ISOLATE                     ((uint16_t)0x0400)  /*!< Isolate PHY from MII                 */
  207.  
  208. #define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020)  /*!< Auto-Negotiation process completed   */
  209. #define PHY_LINKED_STATUS               ((uint16_t)0x0004)  /*!< Valid link established               */
  210. #define PHY_JABBER_DETECTION            ((uint16_t)0x0002)  /*!< Jabber condition detected            */
  211.  
  212. /* Section 4: Extended PHY Registers */
  213.  
  214. #define PHY_SR                          ((uint16_t)0x0010)  /*!< PHY status register Offset                      */
  215. #define PHY_MICR                        ((uint16_t)0x0011)  /*!< MII Interrupt Control Register                  */
  216. #define PHY_MISR                        ((uint16_t)0x0012)  /*!< MII Interrupt Status and Misc. Control Register */
  217.  
  218. #define PHY_LINK_STATUS                 ((uint16_t)0x0001)  /*!< PHY Link mask                                   */
  219. #define PHY_SPEED_STATUS                ((uint16_t)0x0002)  /*!< PHY Speed mask                                  */
  220. #define PHY_DUPLEX_STATUS               ((uint16_t)0x0004)  /*!< PHY Duplex mask                                 */
  221.  
  222. #define PHY_MICR_INT_EN                 ((uint16_t)0x0002)  /*!< PHY Enable interrupts                           */
  223. #define PHY_MICR_INT_OE                 ((uint16_t)0x0001)  /*!< PHY Enable output interrupt events              */
  224.  
  225. #define PHY_MISR_LINK_INT_EN            ((uint16_t)0x0020)  /*!< Enable Interrupt on change of link status       */
  226. #define PHY_LINK_INTERRUPT              ((uint16_t)0x2000)  /*!< PHY link status interrupt mask                  */
  227.  
  228. /* ################## SPI peripheral configuration ########################## */
  229.  
  230. /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
  231. * Activated: CRC code is present inside driver
  232. * Deactivated: CRC code cleaned from driver
  233. */
  234.  
  235. #define USE_SPI_CRC                     1U
  236.  
  237. /* Includes ------------------------------------------------------------------*/
  238. /**
  239.   * @brief Include module's header file
  240.   */
  241.  
  242. #ifdef HAL_RCC_MODULE_ENABLED
  243. #include "stm32f1xx_hal_rcc.h"
  244. #endif /* HAL_RCC_MODULE_ENABLED */
  245.  
  246. #ifdef HAL_GPIO_MODULE_ENABLED
  247. #include "stm32f1xx_hal_gpio.h"
  248. #endif /* HAL_GPIO_MODULE_ENABLED */
  249.  
  250. #ifdef HAL_EXTI_MODULE_ENABLED
  251. #include "stm32f1xx_hal_exti.h"
  252. #endif /* HAL_EXTI_MODULE_ENABLED */
  253.  
  254. #ifdef HAL_DMA_MODULE_ENABLED
  255. #include "stm32f1xx_hal_dma.h"
  256. #endif /* HAL_DMA_MODULE_ENABLED */
  257.  
  258. #ifdef HAL_ETH_MODULE_ENABLED
  259. #include "stm32f1xx_hal_eth.h"
  260. #endif /* HAL_ETH_MODULE_ENABLED */
  261.  
  262. #ifdef HAL_CAN_MODULE_ENABLED
  263. #include "stm32f1xx_hal_can.h"
  264. #endif /* HAL_CAN_MODULE_ENABLED */
  265.  
  266. #ifdef HAL_CAN_LEGACY_MODULE_ENABLED
  267.   #include "Legacy/stm32f1xx_hal_can_legacy.h"
  268. #endif /* HAL_CAN_LEGACY_MODULE_ENABLED */
  269.  
  270. #ifdef HAL_CEC_MODULE_ENABLED
  271. #include "stm32f1xx_hal_cec.h"
  272. #endif /* HAL_CEC_MODULE_ENABLED */
  273.  
  274. #ifdef HAL_CORTEX_MODULE_ENABLED
  275. #include "stm32f1xx_hal_cortex.h"
  276. #endif /* HAL_CORTEX_MODULE_ENABLED */
  277.  
  278. #ifdef HAL_ADC_MODULE_ENABLED
  279. #include "stm32f1xx_hal_adc.h"
  280. #endif /* HAL_ADC_MODULE_ENABLED */
  281.  
  282. #ifdef HAL_CRC_MODULE_ENABLED
  283. #include "stm32f1xx_hal_crc.h"
  284. #endif /* HAL_CRC_MODULE_ENABLED */
  285.  
  286. #ifdef HAL_DAC_MODULE_ENABLED
  287. #include "stm32f1xx_hal_dac.h"
  288. #endif /* HAL_DAC_MODULE_ENABLED */
  289.  
  290. #ifdef HAL_FLASH_MODULE_ENABLED
  291. #include "stm32f1xx_hal_flash.h"
  292. #endif /* HAL_FLASH_MODULE_ENABLED */
  293.  
  294. #ifdef HAL_SRAM_MODULE_ENABLED
  295. #include "stm32f1xx_hal_sram.h"
  296. #endif /* HAL_SRAM_MODULE_ENABLED */
  297.  
  298. #ifdef HAL_NOR_MODULE_ENABLED
  299. #include "stm32f1xx_hal_nor.h"
  300. #endif /* HAL_NOR_MODULE_ENABLED */
  301.  
  302. #ifdef HAL_I2C_MODULE_ENABLED
  303. #include "stm32f1xx_hal_i2c.h"
  304. #endif /* HAL_I2C_MODULE_ENABLED */
  305.  
  306. #ifdef HAL_I2S_MODULE_ENABLED
  307. #include "stm32f1xx_hal_i2s.h"
  308. #endif /* HAL_I2S_MODULE_ENABLED */
  309.  
  310. #ifdef HAL_IWDG_MODULE_ENABLED
  311. #include "stm32f1xx_hal_iwdg.h"
  312. #endif /* HAL_IWDG_MODULE_ENABLED */
  313.  
  314. #ifdef HAL_PWR_MODULE_ENABLED
  315. #include "stm32f1xx_hal_pwr.h"
  316. #endif /* HAL_PWR_MODULE_ENABLED */
  317.  
  318. #ifdef HAL_RTC_MODULE_ENABLED
  319. #include "stm32f1xx_hal_rtc.h"
  320. #endif /* HAL_RTC_MODULE_ENABLED */
  321.  
  322. #ifdef HAL_PCCARD_MODULE_ENABLED
  323. #include "stm32f1xx_hal_pccard.h"
  324. #endif /* HAL_PCCARD_MODULE_ENABLED */
  325.  
  326. #ifdef HAL_SD_MODULE_ENABLED
  327. #include "stm32f1xx_hal_sd.h"
  328. #endif /* HAL_SD_MODULE_ENABLED */
  329.  
  330. #ifdef HAL_NAND_MODULE_ENABLED
  331. #include "stm32f1xx_hal_nand.h"
  332. #endif /* HAL_NAND_MODULE_ENABLED */
  333.  
  334. #ifdef HAL_SPI_MODULE_ENABLED
  335. #include "stm32f1xx_hal_spi.h"
  336. #endif /* HAL_SPI_MODULE_ENABLED */
  337.  
  338. #ifdef HAL_TIM_MODULE_ENABLED
  339. #include "stm32f1xx_hal_tim.h"
  340. #endif /* HAL_TIM_MODULE_ENABLED */
  341.  
  342. #ifdef HAL_UART_MODULE_ENABLED
  343. #include "stm32f1xx_hal_uart.h"
  344. #endif /* HAL_UART_MODULE_ENABLED */
  345.  
  346. #ifdef HAL_USART_MODULE_ENABLED
  347. #include "stm32f1xx_hal_usart.h"
  348. #endif /* HAL_USART_MODULE_ENABLED */
  349.  
  350. #ifdef HAL_IRDA_MODULE_ENABLED
  351. #include "stm32f1xx_hal_irda.h"
  352. #endif /* HAL_IRDA_MODULE_ENABLED */
  353.  
  354. #ifdef HAL_SMARTCARD_MODULE_ENABLED
  355. #include "stm32f1xx_hal_smartcard.h"
  356. #endif /* HAL_SMARTCARD_MODULE_ENABLED */
  357.  
  358. #ifdef HAL_WWDG_MODULE_ENABLED
  359. #include "stm32f1xx_hal_wwdg.h"
  360. #endif /* HAL_WWDG_MODULE_ENABLED */
  361.  
  362. #ifdef HAL_PCD_MODULE_ENABLED
  363. #include "stm32f1xx_hal_pcd.h"
  364. #endif /* HAL_PCD_MODULE_ENABLED */
  365.  
  366. #ifdef HAL_HCD_MODULE_ENABLED
  367. #include "stm32f1xx_hal_hcd.h"
  368. #endif /* HAL_HCD_MODULE_ENABLED */
  369.  
  370. #ifdef HAL_MMC_MODULE_ENABLED
  371. #include "stm32f1xx_hal_mmc.h"
  372. #endif /* HAL_MMC_MODULE_ENABLED */
  373.  
  374. /* Exported macro ------------------------------------------------------------*/
  375. #ifdef  USE_FULL_ASSERT
  376. /**
  377.   * @brief  The assert_param macro is used for function's parameters check.
  378.   * @param  expr If expr is false, it calls assert_failed function
  379.   *         which reports the name of the source file and the source
  380.   *         line number of the call that failed.
  381.   *         If expr is true, it returns no value.
  382.   * @retval None
  383.   */
  384. #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
  385. /* Exported functions ------------------------------------------------------- */
  386. void assert_failed(uint8_t* file, uint32_t line);
  387. #else
  388. #define assert_param(expr) ((void)0U)
  389. #endif /* USE_FULL_ASSERT */
  390.  
  391.  
  392. #ifdef __cplusplus
  393. }
  394. #endif
  395.  
  396. #endif /* __STM32F1xx_HAL_CONF_H */
  397.  
  398.  
  399. /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
  400.