Subversion Repositories DashDisplay

Rev

Rev 61 | Blame | Compare with Previous | Last modification | View Log | Download | RSS feed

  1. /**
  2.   ******************************************************************************
  3.   * @file    stm32l1xx_hal_sd.c
  4.   * @author  MCD Application Team
  5.   * @brief   SD card HAL module driver.
  6.   *          This file provides firmware functions to manage the following
  7.   *          functionalities of the Secure Digital (SD) peripheral:
  8.   *           + Initialization and de-initialization functions
  9.   *           + IO operation functions
  10.   *           + Peripheral Control functions
  11.   *           + Peripheral State functions
  12.   *
  13.   ******************************************************************************
  14.   * @attention
  15.   *
  16.   * Copyright (c) 2016 STMicroelectronics.
  17.   * All rights reserved.
  18.   *
  19.   * This software is licensed under terms that can be found in the LICENSE file
  20.   * in the root directory of this software component.
  21.   * If no LICENSE file comes with this software, it is provided AS-IS.
  22.   *
  23.   ******************************************************************************
  24.   @verbatim
  25.   ==============================================================================
  26.                         ##### How to use this driver #####
  27.   ==============================================================================
  28.   [..]
  29.     This driver implements a high level communication layer for read and write from/to
  30.     this memory. The needed STM32 hardware resources (SDIO and GPIO) are performed by
  31.     the user in HAL_SD_MspInit() function (MSP layer).
  32.     Basically, the MSP layer configuration should be the same as we provide in the
  33.     examples.
  34.     You can easily tailor this configuration according to hardware resources.
  35.  
  36.   [..]
  37.     This driver is a generic layered driver for SDIO memories which uses the HAL
  38.     SDIO driver functions to interface with SD and uSD cards devices.
  39.     It is used as follows:
  40.  
  41.     (#)Initialize the SDIO low level resources by implementing the HAL_SD_MspInit() API:
  42.         (##) Enable the SDIO interface clock using __HAL_RCC_SDIO_CLK_ENABLE();
  43.         (##) SDIO pins configuration for SD card
  44.             (+++) Enable the clock for the SDIO GPIOs using the functions __HAL_RCC_GPIOx_CLK_ENABLE();
  45.             (+++) Configure these SDIO pins as alternate function pull-up using HAL_GPIO_Init()
  46.                   and according to your pin assignment;
  47.         (##) DMA configuration if you need to use DMA process (HAL_SD_ReadBlocks_DMA()
  48.              and HAL_SD_WriteBlocks_DMA() APIs).
  49.             (+++) Enable the DMAx interface clock using __HAL_RCC_DMAx_CLK_ENABLE();
  50.             (+++) Configure the DMA using the function HAL_DMA_Init() with predeclared and filled.
  51.         (##) NVIC configuration if you need to use interrupt process when using DMA transfer.
  52.             (+++) Configure the SDIO and DMA interrupt priorities using functions
  53.                   HAL_NVIC_SetPriority(); DMA priority is superior to SDIO's priority
  54.             (+++) Enable the NVIC DMA and SDIO IRQs using function HAL_NVIC_EnableIRQ()
  55.             (+++) SDIO interrupts are managed using the macros __HAL_SD_ENABLE_IT()
  56.                   and __HAL_SD_DISABLE_IT() inside the communication process.
  57.             (+++) SDIO interrupts pending bits are managed using the macros __HAL_SD_GET_IT()
  58.                   and __HAL_SD_CLEAR_IT()
  59.         (##) NVIC configuration if you need to use interrupt process (HAL_SD_ReadBlocks_IT()
  60.              and HAL_SD_WriteBlocks_IT() APIs).
  61.             (+++) Configure the SDIO interrupt priorities using function HAL_NVIC_SetPriority();
  62.             (+++) Enable the NVIC SDIO IRQs using function HAL_NVIC_EnableIRQ()
  63.             (+++) SDIO interrupts are managed using the macros __HAL_SD_ENABLE_IT()
  64.                   and __HAL_SD_DISABLE_IT() inside the communication process.
  65.             (+++) SDIO interrupts pending bits are managed using the macros __HAL_SD_GET_IT()
  66.                   and __HAL_SD_CLEAR_IT()
  67.     (#) At this stage, you can perform SD read/write/erase operations after SD card initialization
  68.  
  69.  
  70.   *** SD Card Initialization and configuration ***
  71.   ================================================
  72.   [..]
  73.     To initialize the SD Card, use the HAL_SD_Init() function. It Initializes
  74.     SDIO Peripheral(STM32 side) and the SD Card, and put it into StandBy State (Ready for data transfer).
  75.     This function provide the following operations:
  76.  
  77.     (#) Apply the SD Card initialization process at 400KHz and check the SD Card
  78.         type (Standard Capacity or High Capacity). You can change or adapt this
  79.         frequency by adjusting the "ClockDiv" field.
  80.         The SD Card frequency (SDIO_CK) is computed as follows:
  81.  
  82.            SDIO_CK = SDIOCLK / (ClockDiv + 2)
  83.  
  84.         In initialization mode and according to the SD Card standard,
  85.         make sure that the SDIO_CK frequency doesn't exceed 400KHz.
  86.  
  87.         This phase of initialization is done through SDIO_Init() and
  88.         SDIO_PowerState_ON() SDIO low level APIs.
  89.  
  90.     (#) Initialize the SD card. The API used is HAL_SD_InitCard().
  91.         This phase allows the card initialization and identification
  92.         and check the SD Card type (Standard Capacity or High Capacity)
  93.         The initialization flow is compatible with SD standard.
  94.  
  95.         This API (HAL_SD_InitCard()) could be used also to reinitialize the card in case
  96.         of plug-off plug-in.
  97.  
  98.     (#) Configure the SD Card Data transfer frequency. You can change or adapt this
  99.         frequency by adjusting the "ClockDiv" field.
  100.         In transfer mode and according to the SD Card standard, make sure that the
  101.         SDIO_CK frequency doesn't exceed 25MHz and 50MHz in High-speed mode switch.
  102.         To be able to use a frequency higher than 24MHz, you should use the SDIO
  103.         peripheral in bypass mode. Refer to the corresponding reference manual
  104.         for more details.
  105.  
  106.     (#) Select the corresponding SD Card according to the address read with the step 2.
  107.  
  108.     (#) Configure the SD Card in wide bus mode: 4-bits data.
  109.  
  110.   *** SD Card Read operation ***
  111.   ==============================
  112.   [..]
  113.     (+) You can read from SD card in polling mode by using function HAL_SD_ReadBlocks().
  114.         This function support only 512-bytes block length (the block size should be
  115.         chosen as 512 bytes).
  116.         You can choose either one block read operation or multiple block read operation
  117.         by adjusting the "NumberOfBlocks" parameter.
  118.         After this, you have to ensure that the transfer is done correctly. The check is done
  119.         through HAL_SD_GetCardState() function for SD card state.
  120.  
  121.     (+) You can read from SD card in DMA mode by using function HAL_SD_ReadBlocks_DMA().
  122.         This function support only 512-bytes block length (the block size should be
  123.         chosen as 512 bytes).
  124.         You can choose either one block read operation or multiple block read operation
  125.         by adjusting the "NumberOfBlocks" parameter.
  126.         After this, you have to ensure that the transfer is done correctly. The check is done
  127.         through HAL_SD_GetCardState() function for SD card state.
  128.         You could also check the DMA transfer process through the SD Rx interrupt event.
  129.  
  130.     (+) You can read from SD card in Interrupt mode by using function HAL_SD_ReadBlocks_IT().
  131.         This function support only 512-bytes block length (the block size should be
  132.         chosen as 512 bytes).
  133.         You can choose either one block read operation or multiple block read operation
  134.         by adjusting the "NumberOfBlocks" parameter.
  135.         After this, you have to ensure that the transfer is done correctly. The check is done
  136.         through HAL_SD_GetCardState() function for SD card state.
  137.         You could also check the IT transfer process through the SD Rx interrupt event.
  138.  
  139.   *** SD Card Write operation ***
  140.   ===============================
  141.   [..]
  142.     (+) You can write to SD card in polling mode by using function HAL_SD_WriteBlocks().
  143.         This function support only 512-bytes block length (the block size should be
  144.         chosen as 512 bytes).
  145.         You can choose either one block read operation or multiple block read operation
  146.         by adjusting the "NumberOfBlocks" parameter.
  147.         After this, you have to ensure that the transfer is done correctly. The check is done
  148.         through HAL_SD_GetCardState() function for SD card state.
  149.  
  150.     (+) You can write to SD card in DMA mode by using function HAL_SD_WriteBlocks_DMA().
  151.         This function support only 512-bytes block length (the block size should be
  152.         chosen as 512 bytes).
  153.         You can choose either one block read operation or multiple block read operation
  154.         by adjusting the "NumberOfBlocks" parameter.
  155.         After this, you have to ensure that the transfer is done correctly. The check is done
  156.         through HAL_SD_GetCardState() function for SD card state.
  157.         You could also check the DMA transfer process through the SD Tx interrupt event.
  158.  
  159.     (+) You can write to SD card in Interrupt mode by using function HAL_SD_WriteBlocks_IT().
  160.         This function support only 512-bytes block length (the block size should be
  161.         chosen as 512 bytes).
  162.         You can choose either one block read operation or multiple block read operation
  163.         by adjusting the "NumberOfBlocks" parameter.
  164.         After this, you have to ensure that the transfer is done correctly. The check is done
  165.         through HAL_SD_GetCardState() function for SD card state.
  166.         You could also check the IT transfer process through the SD Tx interrupt event.
  167.  
  168.   *** SD card status ***
  169.   ======================
  170.   [..]
  171.     (+) The SD Status contains status bits that are related to the SD Memory
  172.         Card proprietary features. To get SD card status use the HAL_SD_GetCardStatus().
  173.  
  174.   *** SD card information ***
  175.   ===========================
  176.   [..]
  177.     (+) To get SD card information, you can use the function HAL_SD_GetCardInfo().
  178.         It returns useful information about the SD card such as block size, card type,
  179.         block number ...
  180.  
  181.   *** SD card CSD register ***
  182.   ============================
  183.     (+) The HAL_SD_GetCardCSD() API allows to get the parameters of the CSD register.
  184.         Some of the CSD parameters are useful for card initialization and identification.
  185.  
  186.   *** SD card CID register ***
  187.   ============================
  188.     (+) The HAL_SD_GetCardCID() API allows to get the parameters of the CID register.
  189.         Some of the CSD parameters are useful for card initialization and identification.
  190.  
  191.   *** SD HAL driver macros list ***
  192.   ==================================
  193.   [..]
  194.     Below the list of most used macros in SD HAL driver.
  195.  
  196.     (+) __HAL_SD_ENABLE : Enable the SD device
  197.     (+) __HAL_SD_DISABLE : Disable the SD device
  198.     (+) __HAL_SD_DMA_ENABLE: Enable the SDIO DMA transfer
  199.     (+) __HAL_SD_DMA_DISABLE: Disable the SDIO DMA transfer
  200.     (+) __HAL_SD_ENABLE_IT: Enable the SD device interrupt
  201.     (+) __HAL_SD_DISABLE_IT: Disable the SD device interrupt
  202.     (+) __HAL_SD_GET_FLAG:Check whether the specified SD flag is set or not
  203.     (+) __HAL_SD_CLEAR_FLAG: Clear the SD's pending flags
  204.  
  205.     (@) You can refer to the SD HAL driver header file for more useful macros
  206.  
  207.   *** Callback registration ***
  208.   =============================================
  209.   [..]
  210.     The compilation define USE_HAL_SD_REGISTER_CALLBACKS when set to 1
  211.     allows the user to configure dynamically the driver callbacks.
  212.  
  213.     Use Functions HAL_SD_RegisterCallback() to register a user callback,
  214.     it allows to register following callbacks:
  215.       (+) TxCpltCallback : callback when a transmission transfer is completed.
  216.       (+) RxCpltCallback : callback when a reception transfer is completed.
  217.       (+) ErrorCallback : callback when error occurs.
  218.       (+) AbortCpltCallback : callback when abort is completed.
  219.       (+) MspInitCallback    : SD MspInit.
  220.       (+) MspDeInitCallback  : SD MspDeInit.
  221.     This function takes as parameters the HAL peripheral handle, the Callback ID
  222.     and a pointer to the user callback function.
  223.  
  224.     Use function HAL_SD_UnRegisterCallback() to reset a callback to the default
  225.     weak (surcharged) function. It allows to reset following callbacks:
  226.       (+) TxCpltCallback : callback when a transmission transfer is completed.
  227.       (+) RxCpltCallback : callback when a reception transfer is completed.
  228.       (+) ErrorCallback : callback when error occurs.
  229.       (+) AbortCpltCallback : callback when abort is completed.
  230.       (+) MspInitCallback    : SD MspInit.
  231.       (+) MspDeInitCallback  : SD MspDeInit.
  232.     This function) takes as parameters the HAL peripheral handle and the Callback ID.
  233.  
  234.     By default, after the HAL_SD_Init and if the state is HAL_SD_STATE_RESET
  235.     all callbacks are reset to the corresponding legacy weak (surcharged) functions.
  236.     Exception done for MspInit and MspDeInit callbacks that are respectively
  237.     reset to the legacy weak (surcharged) functions in the HAL_SD_Init
  238.     and  HAL_SD_DeInit only when these callbacks are null (not registered beforehand).
  239.     If not, MspInit or MspDeInit are not null, the HAL_SD_Init and HAL_SD_DeInit
  240.     keep and use the user MspInit/MspDeInit callbacks (registered beforehand)
  241.  
  242.     Callbacks can be registered/unregistered in READY state only.
  243.     Exception done for MspInit/MspDeInit callbacks that can be registered/unregistered
  244.     in READY or RESET state, thus registered (user) MspInit/DeInit callbacks can be used
  245.     during the Init/DeInit.
  246.     In that case first register the MspInit/MspDeInit user callbacks
  247.     using HAL_SD_RegisterCallback before calling HAL_SD_DeInit
  248.     or HAL_SD_Init function.
  249.  
  250.     When The compilation define USE_HAL_SD_REGISTER_CALLBACKS is set to 0 or
  251.     not defined, the callback registering feature is not available
  252.     and weak (surcharged) callbacks are used.
  253.  
  254.   @endverbatim
  255.   ******************************************************************************
  256.   */
  257.  
  258. /* Includes ------------------------------------------------------------------*/
  259. #include "stm32l1xx_hal.h"
  260.  
  261. #if defined(SDIO)
  262.  
  263. /** @addtogroup STM32L1xx_HAL_Driver
  264.   * @{
  265.   */
  266.  
  267. /** @addtogroup SD
  268.   * @{
  269.   */
  270.  
  271. #ifdef HAL_SD_MODULE_ENABLED
  272.  
  273. /* Private typedef -----------------------------------------------------------*/
  274. /* Private define ------------------------------------------------------------*/
  275. /** @addtogroup SD_Private_Defines
  276.   * @{
  277.   */
  278.  
  279. /**
  280.   * @}
  281.   */
  282.  
  283. /* Private macro -------------------------------------------------------------*/
  284. /* Private variables ---------------------------------------------------------*/
  285. /* Private function prototypes -----------------------------------------------*/
  286. /* Private functions ---------------------------------------------------------*/
  287. /** @defgroup SD_Private_Functions SD Private Functions
  288.   * @{
  289.   */
  290. static uint32_t SD_InitCard(SD_HandleTypeDef *hsd);
  291. static uint32_t SD_PowerON(SD_HandleTypeDef *hsd);
  292. static uint32_t SD_SendSDStatus(SD_HandleTypeDef *hsd, uint32_t *pSDstatus);
  293. static uint32_t SD_SendStatus(SD_HandleTypeDef *hsd, uint32_t *pCardStatus);
  294. static uint32_t SD_WideBus_Enable(SD_HandleTypeDef *hsd);
  295. static uint32_t SD_WideBus_Disable(SD_HandleTypeDef *hsd);
  296. static uint32_t SD_FindSCR(SD_HandleTypeDef *hsd, uint32_t *pSCR);
  297. static void SD_PowerOFF(SD_HandleTypeDef *hsd);
  298. static void SD_Write_IT(SD_HandleTypeDef *hsd);
  299. static void SD_Read_IT(SD_HandleTypeDef *hsd);
  300. static void SD_DMATransmitCplt(DMA_HandleTypeDef *hdma);
  301. static void SD_DMAReceiveCplt(DMA_HandleTypeDef *hdma);
  302. static void SD_DMAError(DMA_HandleTypeDef *hdma);
  303. static void SD_DMATxAbort(DMA_HandleTypeDef *hdma);
  304. static void SD_DMARxAbort(DMA_HandleTypeDef *hdma);
  305. /**
  306.   * @}
  307.   */
  308.  
  309. /* Exported functions --------------------------------------------------------*/
  310. /** @addtogroup SD_Exported_Functions
  311.   * @{
  312.   */
  313.  
  314. /** @addtogroup SD_Exported_Functions_Group1
  315.  *  @brief   Initialization and de-initialization functions
  316.  *
  317. @verbatim
  318.   ==============================================================================
  319.           ##### Initialization and de-initialization functions #####
  320.   ==============================================================================
  321.   [..]
  322.     This section provides functions allowing to initialize/de-initialize the SD
  323.     card device to be ready for use.
  324.  
  325. @endverbatim
  326.   * @{
  327.   */
  328.  
  329. /**
  330.   * @brief  Initializes the SD according to the specified parameters in the
  331.             SD_HandleTypeDef and create the associated handle.
  332.   * @param  hsd: Pointer to the SD handle
  333.   * @retval HAL status
  334.   */
  335. HAL_StatusTypeDef HAL_SD_Init(SD_HandleTypeDef *hsd)
  336. {
  337.   /* Check the SD handle allocation */
  338.   if(hsd == NULL)
  339.   {
  340.     return HAL_ERROR;
  341.   }
  342.  
  343.   /* Check the parameters */
  344.   assert_param(IS_SDIO_ALL_INSTANCE(hsd->Instance));
  345.   assert_param(IS_SDIO_CLOCK_EDGE(hsd->Init.ClockEdge));
  346.   assert_param(IS_SDIO_CLOCK_BYPASS(hsd->Init.ClockBypass));
  347.   assert_param(IS_SDIO_CLOCK_POWER_SAVE(hsd->Init.ClockPowerSave));
  348.   assert_param(IS_SDIO_BUS_WIDE(hsd->Init.BusWide));
  349.   assert_param(IS_SDIO_HARDWARE_FLOW_CONTROL(hsd->Init.HardwareFlowControl));
  350.   assert_param(IS_SDIO_CLKDIV(hsd->Init.ClockDiv));
  351.  
  352.   if(hsd->State == HAL_SD_STATE_RESET)
  353.   {
  354.     /* Allocate lock resource and initialize it */
  355.     hsd->Lock = HAL_UNLOCKED;
  356. #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U)
  357.     /* Reset Callback pointers in HAL_SD_STATE_RESET only */
  358.     hsd->TxCpltCallback    = HAL_SD_TxCpltCallback;
  359.     hsd->RxCpltCallback    = HAL_SD_RxCpltCallback;
  360.     hsd->ErrorCallback     = HAL_SD_ErrorCallback;
  361.     hsd->AbortCpltCallback = HAL_SD_AbortCallback;
  362.  
  363.     if(hsd->MspInitCallback == NULL)
  364.     {
  365.       hsd->MspInitCallback = HAL_SD_MspInit;
  366.     }
  367.  
  368.     /* Init the low level hardware */
  369.     hsd->MspInitCallback(hsd);
  370. #else
  371.     /* Init the low level hardware : GPIO, CLOCK, CORTEX...etc */
  372.     HAL_SD_MspInit(hsd);
  373. #endif /* USE_HAL_SD_REGISTER_CALLBACKS */
  374.   }
  375.  
  376.   hsd->State = HAL_SD_STATE_BUSY;
  377.  
  378.   /* Initialize the Card parameters */
  379.   if (HAL_SD_InitCard(hsd) != HAL_OK)
  380.   {
  381.     return HAL_ERROR;
  382.   }
  383.  
  384.   /* Initialize the error code */
  385.   hsd->ErrorCode = HAL_SD_ERROR_NONE;
  386.  
  387.   /* Initialize the SD operation */
  388.   hsd->Context = SD_CONTEXT_NONE;
  389.  
  390.   /* Initialize the SD state */
  391.   hsd->State = HAL_SD_STATE_READY;
  392.  
  393.   return HAL_OK;
  394. }
  395.  
  396. /**
  397.   * @brief  Initializes the SD Card.
  398.   * @param  hsd: Pointer to SD handle
  399.   * @note   This function initializes the SD card. It could be used when a card
  400.             re-initialization is needed.
  401.   * @retval HAL status
  402.   */
  403. HAL_StatusTypeDef HAL_SD_InitCard(SD_HandleTypeDef *hsd)
  404. {
  405.   uint32_t errorstate;
  406.   HAL_StatusTypeDef status;
  407.   SD_InitTypeDef Init;
  408.  
  409.   /* Default SDIO peripheral configuration for SD card initialization */
  410.   Init.ClockEdge           = SDIO_CLOCK_EDGE_RISING;
  411.   Init.ClockBypass         = SDIO_CLOCK_BYPASS_DISABLE;
  412.   Init.ClockPowerSave      = SDIO_CLOCK_POWER_SAVE_DISABLE;
  413.   Init.BusWide             = SDIO_BUS_WIDE_1B;
  414.   Init.HardwareFlowControl = SDIO_HARDWARE_FLOW_CONTROL_DISABLE;
  415.   Init.ClockDiv            = SDIO_INIT_CLK_DIV;
  416.  
  417.   /* Initialize SDIO peripheral interface with default configuration */
  418.   status = SDIO_Init(hsd->Instance, Init);
  419.   if(status != HAL_OK)
  420.   {
  421.     return HAL_ERROR;
  422.   }
  423.  
  424.   /* Disable SDIO Clock */
  425.   __HAL_SD_DISABLE(hsd);
  426.  
  427.   /* Set Power State to ON */
  428.   (void)SDIO_PowerState_ON(hsd->Instance);
  429.  
  430.   /* Enable SDIO Clock */
  431.   __HAL_SD_ENABLE(hsd);
  432.  
  433.   /* Required power up waiting time before starting the SD initialization  sequence */
  434.   HAL_Delay(2);
  435.  
  436.   /* Identify card operating voltage */
  437.   errorstate = SD_PowerON(hsd);
  438.   if(errorstate != HAL_SD_ERROR_NONE)
  439.   {
  440.     hsd->State = HAL_SD_STATE_READY;
  441.     hsd->ErrorCode |= errorstate;
  442.     return HAL_ERROR;
  443.   }
  444.  
  445.   /* Card initialization */
  446.   errorstate = SD_InitCard(hsd);
  447.   if(errorstate != HAL_SD_ERROR_NONE)
  448.   {
  449.     hsd->State = HAL_SD_STATE_READY;
  450.     hsd->ErrorCode |= errorstate;
  451.     return HAL_ERROR;
  452.   }
  453.  
  454.   /* Set Block Size for Card */
  455.   errorstate = SDMMC_CmdBlockLength(hsd->Instance, BLOCKSIZE);
  456.   if(errorstate != HAL_SD_ERROR_NONE)
  457.   {
  458.     /* Clear all the static flags */
  459.     __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  460.     hsd->ErrorCode |= errorstate;
  461.     hsd->State = HAL_SD_STATE_READY;
  462.     return HAL_ERROR;
  463.   }
  464.  
  465.   return HAL_OK;
  466. }
  467.  
  468. /**
  469.   * @brief  De-Initializes the SD card.
  470.   * @param  hsd: Pointer to SD handle
  471.   * @retval HAL status
  472.   */
  473. HAL_StatusTypeDef HAL_SD_DeInit(SD_HandleTypeDef *hsd)
  474. {
  475.   /* Check the SD handle allocation */
  476.   if(hsd == NULL)
  477.   {
  478.     return HAL_ERROR;
  479.   }
  480.  
  481.   /* Check the parameters */
  482.   assert_param(IS_SDIO_ALL_INSTANCE(hsd->Instance));
  483.  
  484.   hsd->State = HAL_SD_STATE_BUSY;
  485.  
  486.   /* Set SD power state to off */
  487.   SD_PowerOFF(hsd);
  488.  
  489. #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U)
  490.   if(hsd->MspDeInitCallback == NULL)
  491.   {
  492.     hsd->MspDeInitCallback = HAL_SD_MspDeInit;
  493.   }
  494.  
  495.   /* DeInit the low level hardware */
  496.   hsd->MspDeInitCallback(hsd);
  497. #else
  498.   /* De-Initialize the MSP layer */
  499.   HAL_SD_MspDeInit(hsd);
  500. #endif /* USE_HAL_SD_REGISTER_CALLBACKS */
  501.  
  502.   hsd->ErrorCode = HAL_SD_ERROR_NONE;
  503.   hsd->State = HAL_SD_STATE_RESET;
  504.  
  505.   return HAL_OK;
  506. }
  507.  
  508.  
  509. /**
  510.   * @brief  Initializes the SD MSP.
  511.   * @param  hsd: Pointer to SD handle
  512.   * @retval None
  513.   */
  514. __weak void HAL_SD_MspInit(SD_HandleTypeDef *hsd)
  515. {
  516.   /* Prevent unused argument(s) compilation warning */
  517.   UNUSED(hsd);
  518.  
  519.   /* NOTE : This function should not be modified, when the callback is needed,
  520.             the HAL_SD_MspInit could be implemented in the user file
  521.    */
  522. }
  523.  
  524. /**
  525.   * @brief  De-Initialize SD MSP.
  526.   * @param  hsd: Pointer to SD handle
  527.   * @retval None
  528.   */
  529. __weak void HAL_SD_MspDeInit(SD_HandleTypeDef *hsd)
  530. {
  531.   /* Prevent unused argument(s) compilation warning */
  532.   UNUSED(hsd);
  533.  
  534.   /* NOTE : This function should not be modified, when the callback is needed,
  535.             the HAL_SD_MspDeInit could be implemented in the user file
  536.    */
  537. }
  538.  
  539. /**
  540.   * @}
  541.   */
  542.  
  543. /** @addtogroup SD_Exported_Functions_Group2
  544.  *  @brief   Data transfer functions
  545.  *
  546. @verbatim
  547.   ==============================================================================
  548.                         ##### IO operation functions #####
  549.   ==============================================================================
  550.   [..]
  551.     This subsection provides a set of functions allowing to manage the data
  552.     transfer from/to SD card.
  553.  
  554. @endverbatim
  555.   * @{
  556.   */
  557.  
  558. /**
  559.   * @brief  Reads block(s) from a specified address in a card. The Data transfer
  560.   *         is managed by polling mode.
  561.   * @note   This API should be followed by a check on the card state through
  562.   *         HAL_SD_GetCardState().
  563.   * @param  hsd: Pointer to SD handle
  564.   * @param  pData: pointer to the buffer that will contain the received data
  565.   * @param  BlockAdd: Block Address from where data is to be read
  566.   * @param  NumberOfBlocks: Number of SD blocks to read
  567.   * @param  Timeout: Specify timeout value
  568.   * @retval HAL status
  569.   */
  570. HAL_StatusTypeDef HAL_SD_ReadBlocks(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks, uint32_t Timeout)
  571. {
  572.   SDIO_DataInitTypeDef config;
  573.   uint32_t errorstate;
  574.   uint32_t tickstart = HAL_GetTick();
  575.   uint32_t count, data, dataremaining;
  576.   uint32_t add = BlockAdd;
  577.   uint8_t *tempbuff = pData;
  578.  
  579.   if(NULL == pData)
  580.   {
  581.     hsd->ErrorCode |= HAL_SD_ERROR_PARAM;
  582.     return HAL_ERROR;
  583.   }
  584.  
  585.   if(hsd->State == HAL_SD_STATE_READY)
  586.   {
  587.     hsd->ErrorCode = HAL_SD_ERROR_NONE;
  588.  
  589.     if((add + NumberOfBlocks) > (hsd->SdCard.LogBlockNbr))
  590.     {
  591.       hsd->ErrorCode |= HAL_SD_ERROR_ADDR_OUT_OF_RANGE;
  592.       return HAL_ERROR;
  593.     }
  594.  
  595.     hsd->State = HAL_SD_STATE_BUSY;
  596.  
  597.     /* Initialize data control register */
  598.     hsd->Instance->DCTRL = 0U;
  599.  
  600.     if(hsd->SdCard.CardType != CARD_SDHC_SDXC)
  601.     {
  602.       add *= 512U;
  603.     }
  604.  
  605.     /* Configure the SD DPSM (Data Path State Machine) */
  606.     config.DataTimeOut   = SDMMC_DATATIMEOUT;
  607.     config.DataLength    = NumberOfBlocks * BLOCKSIZE;
  608.     config.DataBlockSize = SDIO_DATABLOCK_SIZE_512B;
  609.     config.TransferDir   = SDIO_TRANSFER_DIR_TO_SDIO;
  610.     config.TransferMode  = SDIO_TRANSFER_MODE_BLOCK;
  611.     config.DPSM          = SDIO_DPSM_ENABLE;
  612.     (void)SDIO_ConfigData(hsd->Instance, &config);
  613.  
  614.     /* Read block(s) in polling mode */
  615.     if(NumberOfBlocks > 1U)
  616.     {
  617.       hsd->Context = SD_CONTEXT_READ_MULTIPLE_BLOCK;
  618.  
  619.       /* Read Multi Block command */
  620.       errorstate = SDMMC_CmdReadMultiBlock(hsd->Instance, add);
  621.     }
  622.     else
  623.     {
  624.       hsd->Context = SD_CONTEXT_READ_SINGLE_BLOCK;
  625.  
  626.       /* Read Single Block command */
  627.       errorstate = SDMMC_CmdReadSingleBlock(hsd->Instance, add);
  628.     }
  629.     if(errorstate != HAL_SD_ERROR_NONE)
  630.     {
  631.       /* Clear all the static flags */
  632.       __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  633.       hsd->ErrorCode |= errorstate;
  634.       hsd->State = HAL_SD_STATE_READY;
  635.       hsd->Context = SD_CONTEXT_NONE;
  636.       return HAL_ERROR;
  637.     }
  638.  
  639.     /* Poll on SDIO flags */
  640.     dataremaining = config.DataLength;
  641.     while(!__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXOVERR | SDIO_FLAG_DCRCFAIL | SDIO_FLAG_DTIMEOUT | SDIO_FLAG_DATAEND | SDIO_FLAG_STBITERR))
  642.     {
  643.       if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXFIFOHF) && (dataremaining > 0U))
  644.       {
  645.         /* Read data from SDIO Rx FIFO */
  646.         for(count = 0U; count < 8U; count++)
  647.         {
  648.           data = SDIO_ReadFIFO(hsd->Instance);
  649.           *tempbuff = (uint8_t)(data & 0xFFU);
  650.           tempbuff++;
  651.           dataremaining--;
  652.           *tempbuff = (uint8_t)((data >> 8U) & 0xFFU);
  653.           tempbuff++;
  654.           dataremaining--;
  655.           *tempbuff = (uint8_t)((data >> 16U) & 0xFFU);
  656.           tempbuff++;
  657.           dataremaining--;
  658.           *tempbuff = (uint8_t)((data >> 24U) & 0xFFU);
  659.           tempbuff++;
  660.           dataremaining--;
  661.         }
  662.       }
  663.  
  664.       if(((HAL_GetTick()-tickstart) >=  Timeout) || (Timeout == 0U))
  665.       {
  666.         /* Clear all the static flags */
  667.         __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  668.         hsd->ErrorCode |= HAL_SD_ERROR_TIMEOUT;
  669.         hsd->State= HAL_SD_STATE_READY;
  670.         hsd->Context = SD_CONTEXT_NONE;
  671.         return HAL_TIMEOUT;
  672.       }
  673.     }
  674.    
  675.     /* Send stop transmission command in case of multiblock read */
  676.     if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DATAEND) && (NumberOfBlocks > 1U))
  677.     {
  678.       if(hsd->SdCard.CardType != CARD_SECURED)
  679.       {
  680.         /* Send stop transmission command */
  681.         errorstate = SDMMC_CmdStopTransfer(hsd->Instance);
  682.         if(errorstate != HAL_SD_ERROR_NONE)
  683.         {
  684.           /* Clear all the static flags */
  685.           __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  686.           hsd->ErrorCode |= errorstate;
  687.           hsd->State = HAL_SD_STATE_READY;
  688.           hsd->Context = SD_CONTEXT_NONE;
  689.           return HAL_ERROR;
  690.         }
  691.       }
  692.     }
  693.  
  694.     /* Get error state */
  695.     if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DTIMEOUT))
  696.     {
  697.       /* Clear all the static flags */
  698.       __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  699.       hsd->ErrorCode |= HAL_SD_ERROR_DATA_TIMEOUT;
  700.       hsd->State = HAL_SD_STATE_READY;
  701.       hsd->Context = SD_CONTEXT_NONE;
  702.       return HAL_ERROR;
  703.     }
  704.     else if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DCRCFAIL))
  705.     {
  706.       /* Clear all the static flags */
  707.       __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  708.       hsd->ErrorCode |= HAL_SD_ERROR_DATA_CRC_FAIL;
  709.       hsd->State = HAL_SD_STATE_READY;
  710.       hsd->Context = SD_CONTEXT_NONE;
  711.       return HAL_ERROR;
  712.     }
  713.     else if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXOVERR))
  714.     {
  715.       /* Clear all the static flags */
  716.       __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  717.       hsd->ErrorCode |= HAL_SD_ERROR_RX_OVERRUN;
  718.       hsd->State = HAL_SD_STATE_READY;
  719.       hsd->Context = SD_CONTEXT_NONE;
  720.       return HAL_ERROR;
  721.     }
  722.     else
  723.     {
  724.       /* Nothing to do */
  725.     }
  726.  
  727.     /* Empty FIFO if there is still any data */
  728.     while ((__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXDAVL)) && (dataremaining > 0U))
  729.     {
  730.       data = SDIO_ReadFIFO(hsd->Instance);
  731.       *tempbuff = (uint8_t)(data & 0xFFU);
  732.       tempbuff++;
  733.       dataremaining--;
  734.       *tempbuff = (uint8_t)((data >> 8U) & 0xFFU);
  735.       tempbuff++;
  736.       dataremaining--;
  737.       *tempbuff = (uint8_t)((data >> 16U) & 0xFFU);
  738.       tempbuff++;
  739.       dataremaining--;
  740.       *tempbuff = (uint8_t)((data >> 24U) & 0xFFU);
  741.       tempbuff++;
  742.       dataremaining--;
  743.  
  744.       if(((HAL_GetTick()-tickstart) >=  Timeout) || (Timeout == 0U))
  745.       {
  746.         /* Clear all the static flags */
  747.         __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  748.         hsd->ErrorCode |= HAL_SD_ERROR_TIMEOUT;
  749.         hsd->State= HAL_SD_STATE_READY;
  750.         hsd->Context = SD_CONTEXT_NONE;
  751.         return HAL_ERROR;
  752.       }
  753.     }
  754.  
  755.     /* Clear all the static flags */
  756.     __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS);
  757.  
  758.     hsd->State = HAL_SD_STATE_READY;
  759.  
  760.     return HAL_OK;
  761.   }
  762.   else
  763.   {
  764.     hsd->ErrorCode |= HAL_SD_ERROR_BUSY;
  765.     return HAL_ERROR;
  766.   }
  767. }
  768.  
  769. /**
  770.   * @brief  Allows to write block(s) to a specified address in a card. The Data
  771.   *         transfer is managed by polling mode.
  772.   * @note   This API should be followed by a check on the card state through
  773.   *         HAL_SD_GetCardState().
  774.   * @param  hsd: Pointer to SD handle
  775.   * @param  pData: pointer to the buffer that will contain the data to transmit
  776.   * @param  BlockAdd: Block Address where data will be written
  777.   * @param  NumberOfBlocks: Number of SD blocks to write
  778.   * @param  Timeout: Specify timeout value
  779.   * @note   Due to limitation "SDIO hardware flow control" indicated in Errata Sheet :
  780.   *         In 4-bits bus wide mode, do not use this API otherwise underrun will occur and
  781.   *         there is not possibility to activate the flow control.
  782.   *         Use DMA mode when using 4-bits bus wide mode or decrease the frequency.
  783.   * @retval HAL status
  784.   */
  785. HAL_StatusTypeDef HAL_SD_WriteBlocks(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks, uint32_t Timeout)
  786. {
  787.   SDIO_DataInitTypeDef config;
  788.   uint32_t errorstate;
  789.   uint32_t tickstart = HAL_GetTick();
  790.   uint32_t count, data, dataremaining;
  791.   uint32_t add = BlockAdd;
  792.   uint8_t *tempbuff = pData;
  793.  
  794.   if(NULL == pData)
  795.   {
  796.     hsd->ErrorCode |= HAL_SD_ERROR_PARAM;
  797.     return HAL_ERROR;
  798.   }
  799.  
  800.   if(hsd->State == HAL_SD_STATE_READY)
  801.   {
  802.     hsd->ErrorCode = HAL_SD_ERROR_NONE;
  803.  
  804.     if((add + NumberOfBlocks) > (hsd->SdCard.LogBlockNbr))
  805.     {
  806.       hsd->ErrorCode |= HAL_SD_ERROR_ADDR_OUT_OF_RANGE;
  807.       return HAL_ERROR;
  808.     }
  809.  
  810.     hsd->State = HAL_SD_STATE_BUSY;
  811.  
  812.     /* Initialize data control register */
  813.     hsd->Instance->DCTRL = 0U;
  814.  
  815.     if(hsd->SdCard.CardType != CARD_SDHC_SDXC)
  816.     {
  817.       add *= 512U;
  818.     }
  819.  
  820.     /* Configure the SD DPSM (Data Path State Machine) */
  821.     config.DataTimeOut   = SDMMC_DATATIMEOUT;
  822.     config.DataLength    = NumberOfBlocks * BLOCKSIZE;
  823.     config.DataBlockSize = SDIO_DATABLOCK_SIZE_512B;
  824.     config.TransferDir   = SDIO_TRANSFER_DIR_TO_CARD;
  825.     config.TransferMode  = SDIO_TRANSFER_MODE_BLOCK;
  826.     config.DPSM          = SDIO_DPSM_ENABLE;
  827.     (void)SDIO_ConfigData(hsd->Instance, &config);
  828.  
  829.     /* Write Blocks in Polling mode */
  830.     if(NumberOfBlocks > 1U)
  831.     {
  832.       hsd->Context = SD_CONTEXT_WRITE_MULTIPLE_BLOCK;
  833.  
  834.       /* Write Multi Block command */
  835.       errorstate = SDMMC_CmdWriteMultiBlock(hsd->Instance, add);
  836.     }
  837.     else
  838.     {
  839.       hsd->Context = SD_CONTEXT_WRITE_SINGLE_BLOCK;
  840.  
  841.       /* Write Single Block command */
  842.       errorstate = SDMMC_CmdWriteSingleBlock(hsd->Instance, add);
  843.     }
  844.     if(errorstate != HAL_SD_ERROR_NONE)
  845.     {
  846.       /* Clear all the static flags */
  847.       __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  848.       hsd->ErrorCode |= errorstate;
  849.       hsd->State = HAL_SD_STATE_READY;
  850.       hsd->Context = SD_CONTEXT_NONE;
  851.       return HAL_ERROR;
  852.     }
  853.  
  854.     /* Write block(s) in polling mode */
  855.     dataremaining = config.DataLength;
  856.     while(!__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_TXUNDERR | SDIO_FLAG_DCRCFAIL | SDIO_FLAG_DTIMEOUT | SDIO_FLAG_DATAEND | SDIO_FLAG_STBITERR))
  857.     {
  858.       if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_TXFIFOHE) && (dataremaining > 0U))
  859.       {
  860.         /* Write data to SDIO Tx FIFO */
  861.         for(count = 0U; count < 8U; count++)
  862.         {
  863.           data = (uint32_t)(*tempbuff);
  864.           tempbuff++;
  865.           dataremaining--;
  866.           data |= ((uint32_t)(*tempbuff) << 8U);
  867.           tempbuff++;
  868.           dataremaining--;
  869.           data |= ((uint32_t)(*tempbuff) << 16U);
  870.           tempbuff++;
  871.           dataremaining--;
  872.           data |= ((uint32_t)(*tempbuff) << 24U);
  873.           tempbuff++;
  874.           dataremaining--;
  875.           (void)SDIO_WriteFIFO(hsd->Instance, &data);
  876.         }
  877.       }
  878.  
  879.       if(((HAL_GetTick()-tickstart) >=  Timeout) || (Timeout == 0U))
  880.       {
  881.         /* Clear all the static flags */
  882.         __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  883.         hsd->ErrorCode |= errorstate;
  884.         hsd->State = HAL_SD_STATE_READY;
  885.         hsd->Context = SD_CONTEXT_NONE;
  886.         return HAL_TIMEOUT;
  887.       }
  888.     }
  889.  
  890.     /* Send stop transmission command in case of multiblock write */
  891.     if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DATAEND) && (NumberOfBlocks > 1U))
  892.     {
  893.       if(hsd->SdCard.CardType != CARD_SECURED)
  894.       {
  895.         /* Send stop transmission command */
  896.         errorstate = SDMMC_CmdStopTransfer(hsd->Instance);
  897.         if(errorstate != HAL_SD_ERROR_NONE)
  898.         {
  899.           /* Clear all the static flags */
  900.           __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  901.           hsd->ErrorCode |= errorstate;
  902.           hsd->State = HAL_SD_STATE_READY;
  903.           hsd->Context = SD_CONTEXT_NONE;
  904.           return HAL_ERROR;
  905.         }
  906.       }
  907.     }
  908.  
  909.     /* Get error state */
  910.     if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DTIMEOUT))
  911.     {
  912.       /* Clear all the static flags */
  913.       __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  914.       hsd->ErrorCode |= HAL_SD_ERROR_DATA_TIMEOUT;
  915.       hsd->State = HAL_SD_STATE_READY;
  916.       hsd->Context = SD_CONTEXT_NONE;
  917.       return HAL_ERROR;
  918.     }
  919.     else if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DCRCFAIL))
  920.     {
  921.       /* Clear all the static flags */
  922.       __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  923.       hsd->ErrorCode |= HAL_SD_ERROR_DATA_CRC_FAIL;
  924.       hsd->State = HAL_SD_STATE_READY;
  925.       hsd->Context = SD_CONTEXT_NONE;
  926.       return HAL_ERROR;
  927.     }
  928.     else if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_TXUNDERR))
  929.     {
  930.       /* Clear all the static flags */
  931.       __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  932.       hsd->ErrorCode |= HAL_SD_ERROR_TX_UNDERRUN;
  933.       hsd->State = HAL_SD_STATE_READY;
  934.       hsd->Context = SD_CONTEXT_NONE;
  935.       return HAL_ERROR;
  936.     }
  937.     else
  938.     {
  939.       /* Nothing to do */
  940.     }
  941.  
  942.     /* Clear all the static flags */
  943.     __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS);
  944.  
  945.     hsd->State = HAL_SD_STATE_READY;
  946.  
  947.     return HAL_OK;
  948.   }
  949.   else
  950.   {
  951.     hsd->ErrorCode |= HAL_SD_ERROR_BUSY;
  952.     return HAL_ERROR;
  953.   }
  954. }
  955.  
  956. /**
  957.   * @brief  Reads block(s) from a specified address in a card. The Data transfer
  958.   *         is managed in interrupt mode.
  959.   * @note   This API should be followed by a check on the card state through
  960.   *         HAL_SD_GetCardState().
  961.   * @note   You could also check the IT transfer process through the SD Rx
  962.   *         interrupt event.
  963.   * @param  hsd: Pointer to SD handle
  964.   * @param  pData: Pointer to the buffer that will contain the received data
  965.   * @param  BlockAdd: Block Address from where data is to be read
  966.   * @param  NumberOfBlocks: Number of blocks to read.
  967.   * @retval HAL status
  968.   */
  969. HAL_StatusTypeDef HAL_SD_ReadBlocks_IT(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks)
  970. {
  971.   SDIO_DataInitTypeDef config;
  972.   uint32_t errorstate;
  973.   uint32_t add = BlockAdd;
  974.  
  975.   if(NULL == pData)
  976.   {
  977.     hsd->ErrorCode |= HAL_SD_ERROR_PARAM;
  978.     return HAL_ERROR;
  979.   }
  980.  
  981.   if(hsd->State == HAL_SD_STATE_READY)
  982.   {
  983.     hsd->ErrorCode = HAL_SD_ERROR_NONE;
  984.  
  985.     if((add + NumberOfBlocks) > (hsd->SdCard.LogBlockNbr))
  986.     {
  987.       hsd->ErrorCode |= HAL_SD_ERROR_ADDR_OUT_OF_RANGE;
  988.       return HAL_ERROR;
  989.     }
  990.  
  991.     hsd->State = HAL_SD_STATE_BUSY;
  992.  
  993.     /* Initialize data control register */
  994.     hsd->Instance->DCTRL = 0U;
  995.  
  996.     hsd->pRxBuffPtr = pData;
  997.     hsd->RxXferSize = BLOCKSIZE * NumberOfBlocks;
  998.  
  999.     __HAL_SD_ENABLE_IT(hsd, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_RXOVERR | SDIO_IT_DATAEND | SDIO_FLAG_RXFIFOHF | SDIO_IT_STBITERR));
  1000.  
  1001.     if(hsd->SdCard.CardType != CARD_SDHC_SDXC)
  1002.     {
  1003.       add *= 512U;
  1004.     }
  1005.  
  1006.     /* Configure the SD DPSM (Data Path State Machine) */
  1007.     config.DataTimeOut   = SDMMC_DATATIMEOUT;
  1008.     config.DataLength    = BLOCKSIZE * NumberOfBlocks;
  1009.     config.DataBlockSize = SDIO_DATABLOCK_SIZE_512B;
  1010.     config.TransferDir   = SDIO_TRANSFER_DIR_TO_SDIO;
  1011.     config.TransferMode  = SDIO_TRANSFER_MODE_BLOCK;
  1012.     config.DPSM          = SDIO_DPSM_ENABLE;
  1013.     (void)SDIO_ConfigData(hsd->Instance, &config);
  1014.  
  1015.     /* Read Blocks in IT mode */
  1016.     if(NumberOfBlocks > 1U)
  1017.     {
  1018.       hsd->Context = (SD_CONTEXT_READ_MULTIPLE_BLOCK | SD_CONTEXT_IT);
  1019.  
  1020.       /* Read Multi Block command */
  1021.       errorstate = SDMMC_CmdReadMultiBlock(hsd->Instance, add);
  1022.     }
  1023.     else
  1024.     {
  1025.       hsd->Context = (SD_CONTEXT_READ_SINGLE_BLOCK | SD_CONTEXT_IT);
  1026.  
  1027.       /* Read Single Block command */
  1028.       errorstate = SDMMC_CmdReadSingleBlock(hsd->Instance, add);
  1029.     }
  1030.     if(errorstate != HAL_SD_ERROR_NONE)
  1031.     {
  1032.       /* Clear all the static flags */
  1033.       __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  1034.       hsd->ErrorCode |= errorstate;
  1035.       hsd->State = HAL_SD_STATE_READY;
  1036.       hsd->Context = SD_CONTEXT_NONE;
  1037.       return HAL_ERROR;
  1038.     }
  1039.  
  1040.     return HAL_OK;
  1041.   }
  1042.   else
  1043.   {
  1044.     return HAL_BUSY;
  1045.   }
  1046. }
  1047.  
  1048. /**
  1049.   * @brief  Writes block(s) to a specified address in a card. The Data transfer
  1050.   *         is managed in interrupt mode.
  1051.   * @note   This API should be followed by a check on the card state through
  1052.   *         HAL_SD_GetCardState().
  1053.   * @note   You could also check the IT transfer process through the SD Tx
  1054.   *         interrupt event.
  1055.   * @param  hsd: Pointer to SD handle
  1056.   * @param  pData: Pointer to the buffer that will contain the data to transmit
  1057.   * @param  BlockAdd: Block Address where data will be written
  1058.   * @param  NumberOfBlocks: Number of blocks to write
  1059.   * @note   Due to limitation "SDIO hardware flow control" indicated in Errata Sheet :
  1060.   *         In 4-bits bus wide mode, do not use this API otherwise underrun will occur and
  1061.   *         there is not possibility to activate the flow control.
  1062.   *         Use DMA mode when using 4-bits bus wide mode or decrease the frequency.
  1063.   * @retval HAL status
  1064.   */
  1065. HAL_StatusTypeDef HAL_SD_WriteBlocks_IT(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks)
  1066. {
  1067.   SDIO_DataInitTypeDef config;
  1068.   uint32_t errorstate;
  1069.   uint32_t add = BlockAdd;
  1070.  
  1071.   if(NULL == pData)
  1072.   {
  1073.     hsd->ErrorCode |= HAL_SD_ERROR_PARAM;
  1074.     return HAL_ERROR;
  1075.   }
  1076.  
  1077.   if(hsd->State == HAL_SD_STATE_READY)
  1078.   {
  1079.     hsd->ErrorCode = HAL_SD_ERROR_NONE;
  1080.  
  1081.     if((add + NumberOfBlocks) > (hsd->SdCard.LogBlockNbr))
  1082.     {
  1083.       hsd->ErrorCode |= HAL_SD_ERROR_ADDR_OUT_OF_RANGE;
  1084.       return HAL_ERROR;
  1085.     }
  1086.  
  1087.     hsd->State = HAL_SD_STATE_BUSY;
  1088.  
  1089.     /* Initialize data control register */
  1090.     hsd->Instance->DCTRL = 0U;
  1091.  
  1092.     hsd->pTxBuffPtr = pData;
  1093.     hsd->TxXferSize = BLOCKSIZE * NumberOfBlocks;
  1094.  
  1095.     /* Enable transfer interrupts */
  1096.     __HAL_SD_ENABLE_IT(hsd, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_TXUNDERR | SDIO_IT_DATAEND | SDIO_FLAG_TXFIFOHE | SDIO_IT_STBITERR));
  1097.  
  1098.     if(hsd->SdCard.CardType != CARD_SDHC_SDXC)
  1099.     {
  1100.       add *= 512U;
  1101.     }
  1102.  
  1103.     /* Write Blocks in Polling mode */
  1104.     if(NumberOfBlocks > 1U)
  1105.     {
  1106.       hsd->Context = (SD_CONTEXT_WRITE_MULTIPLE_BLOCK| SD_CONTEXT_IT);
  1107.  
  1108.       /* Write Multi Block command */
  1109.       errorstate = SDMMC_CmdWriteMultiBlock(hsd->Instance, add);
  1110.     }
  1111.     else
  1112.     {
  1113.       hsd->Context = (SD_CONTEXT_WRITE_SINGLE_BLOCK | SD_CONTEXT_IT);
  1114.  
  1115.       /* Write Single Block command */
  1116.       errorstate = SDMMC_CmdWriteSingleBlock(hsd->Instance, add);
  1117.     }
  1118.     if(errorstate != HAL_SD_ERROR_NONE)
  1119.     {
  1120.       /* Clear all the static flags */
  1121.       __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  1122.       hsd->ErrorCode |= errorstate;
  1123.       hsd->State = HAL_SD_STATE_READY;
  1124.       hsd->Context = SD_CONTEXT_NONE;
  1125.       return HAL_ERROR;
  1126.     }
  1127.  
  1128.     /* Configure the SD DPSM (Data Path State Machine) */
  1129.     config.DataTimeOut   = SDMMC_DATATIMEOUT;
  1130.     config.DataLength    = BLOCKSIZE * NumberOfBlocks;
  1131.     config.DataBlockSize = SDIO_DATABLOCK_SIZE_512B;
  1132.     config.TransferDir   = SDIO_TRANSFER_DIR_TO_CARD;
  1133.     config.TransferMode  = SDIO_TRANSFER_MODE_BLOCK;
  1134.     config.DPSM          = SDIO_DPSM_ENABLE;
  1135.     (void)SDIO_ConfigData(hsd->Instance, &config);
  1136.  
  1137.     return HAL_OK;
  1138.   }
  1139.   else
  1140.   {
  1141.     return HAL_BUSY;
  1142.   }
  1143. }
  1144.  
  1145. /**
  1146.   * @brief  Reads block(s) from a specified address in a card. The Data transfer
  1147.   *         is managed by DMA mode.
  1148.   * @note   This API should be followed by a check on the card state through
  1149.   *         HAL_SD_GetCardState().
  1150.   * @note   You could also check the DMA transfer process through the SD Rx
  1151.   *         interrupt event.
  1152.   * @param  hsd: Pointer SD handle
  1153.   * @param  pData: Pointer to the buffer that will contain the received data
  1154.   * @param  BlockAdd: Block Address from where data is to be read
  1155.   * @param  NumberOfBlocks: Number of blocks to read.
  1156.   * @retval HAL status
  1157.   */
  1158. HAL_StatusTypeDef HAL_SD_ReadBlocks_DMA(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks)
  1159. {
  1160.   SDIO_DataInitTypeDef config;
  1161.   uint32_t errorstate;
  1162.   uint32_t add = BlockAdd;
  1163.  
  1164.   if(NULL == pData)
  1165.   {
  1166.     hsd->ErrorCode |= HAL_SD_ERROR_PARAM;
  1167.     return HAL_ERROR;
  1168.   }
  1169.  
  1170.   if(hsd->State == HAL_SD_STATE_READY)
  1171.   {
  1172.     hsd->ErrorCode = HAL_SD_ERROR_NONE;
  1173.  
  1174.     if((add + NumberOfBlocks) > (hsd->SdCard.LogBlockNbr))
  1175.     {
  1176.       hsd->ErrorCode |= HAL_SD_ERROR_ADDR_OUT_OF_RANGE;
  1177.       return HAL_ERROR;
  1178.     }
  1179.  
  1180.     hsd->State = HAL_SD_STATE_BUSY;
  1181.  
  1182.     /* Initialize data control register */
  1183.     hsd->Instance->DCTRL = 0U;
  1184.  
  1185.     __HAL_SD_ENABLE_IT(hsd, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_RXOVERR | SDIO_IT_DATAEND | SDIO_IT_STBITERR));
  1186.  
  1187.     /* Set the DMA transfer complete callback */
  1188.     hsd->hdmarx->XferCpltCallback = SD_DMAReceiveCplt;
  1189.  
  1190.     /* Set the DMA error callback */
  1191.     hsd->hdmarx->XferErrorCallback = SD_DMAError;
  1192.  
  1193.     /* Set the DMA Abort callback */
  1194.     hsd->hdmarx->XferAbortCallback = NULL;
  1195.  
  1196.     /* Force DMA Direction */
  1197.     hsd->hdmarx->Init.Direction = DMA_PERIPH_TO_MEMORY;
  1198.     MODIFY_REG(hsd->hdmarx->Instance->CCR, DMA_CCR_DIR, hsd->hdmarx->Init.Direction);
  1199.  
  1200.     /* Enable the DMA Channel */
  1201.     if(HAL_DMA_Start_IT(hsd->hdmarx, (uint32_t)&hsd->Instance->FIFO, (uint32_t)pData, (uint32_t)(BLOCKSIZE * NumberOfBlocks)/4U) != HAL_OK)
  1202.     {
  1203.       __HAL_SD_DISABLE_IT(hsd, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_RXOVERR | SDIO_IT_DATAEND));
  1204.       __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  1205.       hsd->ErrorCode |= HAL_SD_ERROR_DMA;
  1206.       hsd->State = HAL_SD_STATE_READY;
  1207.       return HAL_ERROR;
  1208.     }
  1209.     else
  1210.     {
  1211.       /* Enable SD DMA transfer */
  1212.       __HAL_SD_DMA_ENABLE(hsd);
  1213.  
  1214.       if(hsd->SdCard.CardType != CARD_SDHC_SDXC)
  1215.       {
  1216.         add *= 512U;
  1217.       }
  1218.  
  1219.       /* Configure the SD DPSM (Data Path State Machine) */
  1220.       config.DataTimeOut   = SDMMC_DATATIMEOUT;
  1221.       config.DataLength    = BLOCKSIZE * NumberOfBlocks;
  1222.       config.DataBlockSize = SDIO_DATABLOCK_SIZE_512B;
  1223.       config.TransferDir   = SDIO_TRANSFER_DIR_TO_SDIO;
  1224.       config.TransferMode  = SDIO_TRANSFER_MODE_BLOCK;
  1225.       config.DPSM          = SDIO_DPSM_ENABLE;
  1226.       (void)SDIO_ConfigData(hsd->Instance, &config);
  1227.  
  1228.       /* Read Blocks in DMA mode */
  1229.       if(NumberOfBlocks > 1U)
  1230.       {
  1231.         hsd->Context = (SD_CONTEXT_READ_MULTIPLE_BLOCK | SD_CONTEXT_DMA);
  1232.  
  1233.         /* Read Multi Block command */
  1234.         errorstate = SDMMC_CmdReadMultiBlock(hsd->Instance, add);
  1235.       }
  1236.       else
  1237.       {
  1238.         hsd->Context = (SD_CONTEXT_READ_SINGLE_BLOCK | SD_CONTEXT_DMA);
  1239.  
  1240.         /* Read Single Block command */
  1241.         errorstate = SDMMC_CmdReadSingleBlock(hsd->Instance, add);
  1242.       }
  1243.       if(errorstate != HAL_SD_ERROR_NONE)
  1244.       {
  1245.         /* Clear all the static flags */
  1246.         __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  1247.         hsd->ErrorCode |= errorstate;
  1248.         hsd->State = HAL_SD_STATE_READY;
  1249.         hsd->Context = SD_CONTEXT_NONE;
  1250.         return HAL_ERROR;
  1251.       }
  1252.  
  1253.       return HAL_OK;
  1254.     }
  1255.   }
  1256.   else
  1257.   {
  1258.     return HAL_BUSY;
  1259.   }
  1260. }
  1261.  
  1262. /**
  1263.   * @brief  Writes block(s) to a specified address in a card. The Data transfer
  1264.   *         is managed by DMA mode.
  1265.   * @note   This API should be followed by a check on the card state through
  1266.   *         HAL_SD_GetCardState().
  1267.   * @note   You could also check the DMA transfer process through the SD Tx
  1268.   *         interrupt event.
  1269.   * @param  hsd: Pointer to SD handle
  1270.   * @param  pData: Pointer to the buffer that will contain the data to transmit
  1271.   * @param  BlockAdd: Block Address where data will be written
  1272.   * @param  NumberOfBlocks: Number of blocks to write
  1273.   * @retval HAL status
  1274.   */
  1275. HAL_StatusTypeDef HAL_SD_WriteBlocks_DMA(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks)
  1276. {
  1277.   SDIO_DataInitTypeDef config;
  1278.   uint32_t errorstate;
  1279.   uint32_t add = BlockAdd;
  1280.  
  1281.   if(NULL == pData)
  1282.   {
  1283.     hsd->ErrorCode |= HAL_SD_ERROR_PARAM;
  1284.     return HAL_ERROR;
  1285.   }
  1286.  
  1287.   if(hsd->State == HAL_SD_STATE_READY)
  1288.   {
  1289.     hsd->ErrorCode = HAL_SD_ERROR_NONE;
  1290.  
  1291.     if((add + NumberOfBlocks) > (hsd->SdCard.LogBlockNbr))
  1292.     {
  1293.       hsd->ErrorCode |= HAL_SD_ERROR_ADDR_OUT_OF_RANGE;
  1294.       return HAL_ERROR;
  1295.     }
  1296.  
  1297.     hsd->State = HAL_SD_STATE_BUSY;
  1298.  
  1299.     /* Initialize data control register */
  1300.     hsd->Instance->DCTRL = 0U;
  1301.  
  1302.     /* Enable SD Error interrupts */
  1303.     __HAL_SD_ENABLE_IT(hsd, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_TXUNDERR | SDIO_IT_STBITERR));
  1304.  
  1305.     /* Set the DMA transfer complete callback */
  1306.     hsd->hdmatx->XferCpltCallback = SD_DMATransmitCplt;
  1307.  
  1308.     /* Set the DMA error callback */
  1309.     hsd->hdmatx->XferErrorCallback = SD_DMAError;
  1310.  
  1311.     /* Set the DMA Abort callback */
  1312.     hsd->hdmatx->XferAbortCallback = NULL;
  1313.  
  1314.     if(hsd->SdCard.CardType != CARD_SDHC_SDXC)
  1315.     {
  1316.       add *= 512U;
  1317.     }
  1318.  
  1319.     /* Write Blocks in Polling mode */
  1320.     if(NumberOfBlocks > 1U)
  1321.     {
  1322.       hsd->Context = (SD_CONTEXT_WRITE_MULTIPLE_BLOCK | SD_CONTEXT_DMA);
  1323.  
  1324.       /* Write Multi Block command */
  1325.       errorstate = SDMMC_CmdWriteMultiBlock(hsd->Instance, add);
  1326.     }
  1327.     else
  1328.     {
  1329.       hsd->Context = (SD_CONTEXT_WRITE_SINGLE_BLOCK | SD_CONTEXT_DMA);
  1330.  
  1331.       /* Write Single Block command */
  1332.       errorstate = SDMMC_CmdWriteSingleBlock(hsd->Instance, add);
  1333.     }
  1334.     if(errorstate != HAL_SD_ERROR_NONE)
  1335.     {
  1336.       /* Clear all the static flags */
  1337.       __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  1338.       hsd->ErrorCode |= errorstate;
  1339.       hsd->State = HAL_SD_STATE_READY;
  1340.       hsd->Context = SD_CONTEXT_NONE;
  1341.       return HAL_ERROR;
  1342.     }
  1343.  
  1344.     /* Enable SDIO DMA transfer */
  1345.     __HAL_SD_DMA_ENABLE(hsd);
  1346.  
  1347.     /* Force DMA Direction */
  1348.     hsd->hdmatx->Init.Direction = DMA_MEMORY_TO_PERIPH;
  1349.     MODIFY_REG(hsd->hdmatx->Instance->CCR, DMA_CCR_DIR, hsd->hdmatx->Init.Direction);
  1350.  
  1351.     /* Enable the DMA Channel */
  1352.     if(HAL_DMA_Start_IT(hsd->hdmatx, (uint32_t)pData, (uint32_t)&hsd->Instance->FIFO, (uint32_t)(BLOCKSIZE * NumberOfBlocks)/4U) != HAL_OK)
  1353.     {
  1354.       __HAL_SD_DISABLE_IT(hsd, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_TXUNDERR | SDIO_IT_STBITERR));
  1355.       __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  1356.       hsd->ErrorCode |= HAL_SD_ERROR_DMA;
  1357.       hsd->State = HAL_SD_STATE_READY;
  1358.       hsd->Context = SD_CONTEXT_NONE;
  1359.       return HAL_ERROR;
  1360.     }
  1361.     else
  1362.     {
  1363.       /* Configure the SD DPSM (Data Path State Machine) */
  1364.       config.DataTimeOut   = SDMMC_DATATIMEOUT;
  1365.       config.DataLength    = BLOCKSIZE * NumberOfBlocks;
  1366.       config.DataBlockSize = SDIO_DATABLOCK_SIZE_512B;
  1367.       config.TransferDir   = SDIO_TRANSFER_DIR_TO_CARD;
  1368.       config.TransferMode  = SDIO_TRANSFER_MODE_BLOCK;
  1369.       config.DPSM          = SDIO_DPSM_ENABLE;
  1370.       (void)SDIO_ConfigData(hsd->Instance, &config);
  1371.  
  1372.       return HAL_OK;
  1373.     }
  1374.   }
  1375.   else
  1376.   {
  1377.     return HAL_BUSY;
  1378.   }
  1379. }
  1380.  
  1381. /**
  1382.   * @brief  Erases the specified memory area of the given SD card.
  1383.   * @note   This API should be followed by a check on the card state through
  1384.   *         HAL_SD_GetCardState().
  1385.   * @param  hsd: Pointer to SD handle
  1386.   * @param  BlockStartAdd: Start Block address
  1387.   * @param  BlockEndAdd: End Block address
  1388.   * @retval HAL status
  1389.   */
  1390. HAL_StatusTypeDef HAL_SD_Erase(SD_HandleTypeDef *hsd, uint32_t BlockStartAdd, uint32_t BlockEndAdd)
  1391. {
  1392.   uint32_t errorstate;
  1393.   uint32_t start_add = BlockStartAdd;
  1394.   uint32_t end_add = BlockEndAdd;
  1395.  
  1396.   if(hsd->State == HAL_SD_STATE_READY)
  1397.   {
  1398.     hsd->ErrorCode = HAL_SD_ERROR_NONE;
  1399.  
  1400.     if(end_add < start_add)
  1401.     {
  1402.       hsd->ErrorCode |= HAL_SD_ERROR_PARAM;
  1403.       return HAL_ERROR;
  1404.     }
  1405.  
  1406.     if(end_add > (hsd->SdCard.LogBlockNbr))
  1407.     {
  1408.       hsd->ErrorCode |= HAL_SD_ERROR_ADDR_OUT_OF_RANGE;
  1409.       return HAL_ERROR;
  1410.     }
  1411.  
  1412.     hsd->State = HAL_SD_STATE_BUSY;
  1413.  
  1414.     /* Check if the card command class supports erase command */
  1415.     if(((hsd->SdCard.Class) & SDIO_CCCC_ERASE) == 0U)
  1416.     {
  1417.       /* Clear all the static flags */
  1418.       __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  1419.       hsd->ErrorCode |= HAL_SD_ERROR_REQUEST_NOT_APPLICABLE;
  1420.       hsd->State = HAL_SD_STATE_READY;
  1421.       return HAL_ERROR;
  1422.     }
  1423.  
  1424.     if((SDIO_GetResponse(hsd->Instance, SDIO_RESP1) & SDMMC_CARD_LOCKED) == SDMMC_CARD_LOCKED)
  1425.     {
  1426.       /* Clear all the static flags */
  1427.       __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  1428.       hsd->ErrorCode |= HAL_SD_ERROR_LOCK_UNLOCK_FAILED;
  1429.       hsd->State = HAL_SD_STATE_READY;
  1430.       return HAL_ERROR;
  1431.     }
  1432.  
  1433.     /* Get start and end block for high capacity cards */
  1434.     if(hsd->SdCard.CardType != CARD_SDHC_SDXC)
  1435.     {
  1436.       start_add *= 512U;
  1437.       end_add   *= 512U;
  1438.     }
  1439.  
  1440.     /* According to sd-card spec 1.0 ERASE_GROUP_START (CMD32) and erase_group_end(CMD33) */
  1441.     if(hsd->SdCard.CardType != CARD_SECURED)
  1442.     {
  1443.       /* Send CMD32 SD_ERASE_GRP_START with argument as addr  */
  1444.       errorstate = SDMMC_CmdSDEraseStartAdd(hsd->Instance, start_add);
  1445.       if(errorstate != HAL_SD_ERROR_NONE)
  1446.       {
  1447.         /* Clear all the static flags */
  1448.         __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  1449.         hsd->ErrorCode |= errorstate;
  1450.         hsd->State = HAL_SD_STATE_READY;
  1451.         return HAL_ERROR;
  1452.       }
  1453.  
  1454.       /* Send CMD33 SD_ERASE_GRP_END with argument as addr  */
  1455.       errorstate = SDMMC_CmdSDEraseEndAdd(hsd->Instance, end_add);
  1456.       if(errorstate != HAL_SD_ERROR_NONE)
  1457.       {
  1458.         /* Clear all the static flags */
  1459.         __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  1460.         hsd->ErrorCode |= errorstate;
  1461.         hsd->State = HAL_SD_STATE_READY;
  1462.         return HAL_ERROR;
  1463.       }
  1464.     }
  1465.  
  1466.     /* Send CMD38 ERASE */
  1467.     errorstate = SDMMC_CmdErase(hsd->Instance);
  1468.     if(errorstate != HAL_SD_ERROR_NONE)
  1469.     {
  1470.       /* Clear all the static flags */
  1471.       __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  1472.       hsd->ErrorCode |= errorstate;
  1473.       hsd->State = HAL_SD_STATE_READY;
  1474.       return HAL_ERROR;
  1475.     }
  1476.  
  1477.     hsd->State = HAL_SD_STATE_READY;
  1478.  
  1479.     return HAL_OK;
  1480.   }
  1481.   else
  1482.   {
  1483.     return HAL_BUSY;
  1484.   }
  1485. }
  1486.  
  1487. /**
  1488.   * @brief  This function handles SD card interrupt request.
  1489.   * @param  hsd: Pointer to SD handle
  1490.   * @retval None
  1491.   */
  1492. void HAL_SD_IRQHandler(SD_HandleTypeDef *hsd)
  1493. {
  1494.   uint32_t errorstate;
  1495.   uint32_t context = hsd->Context;
  1496.  
  1497.   /* Check for SDIO interrupt flags */
  1498.   if((__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXFIFOHF) != RESET) && ((context & SD_CONTEXT_IT) != 0U))
  1499.   {
  1500.     SD_Read_IT(hsd);
  1501.   }
  1502.  
  1503.   else if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DATAEND) != RESET)
  1504.   {
  1505.     __HAL_SD_CLEAR_FLAG(hsd, SDIO_FLAG_DATAEND);
  1506.  
  1507.     __HAL_SD_DISABLE_IT(hsd, SDIO_IT_DATAEND  | SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT|\
  1508.                              SDIO_IT_TXUNDERR | SDIO_IT_RXOVERR  | SDIO_IT_TXFIFOHE |\
  1509.                              SDIO_IT_RXFIFOHF | SDIO_IT_STBITERR);
  1510.  
  1511.     hsd->Instance->DCTRL &= ~(SDIO_DCTRL_DTEN);
  1512.    
  1513.     if((context & SD_CONTEXT_IT) != 0U)
  1514.     {
  1515.       if(((context & SD_CONTEXT_READ_MULTIPLE_BLOCK) != 0U) || ((context & SD_CONTEXT_WRITE_MULTIPLE_BLOCK) != 0U))
  1516.       {
  1517.         errorstate = SDMMC_CmdStopTransfer(hsd->Instance);
  1518.         if(errorstate != HAL_SD_ERROR_NONE)
  1519.         {
  1520.           hsd->ErrorCode |= errorstate;
  1521. #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U)
  1522.           hsd->ErrorCallback(hsd);
  1523. #else
  1524.           HAL_SD_ErrorCallback(hsd);
  1525. #endif /* USE_HAL_SD_REGISTER_CALLBACKS */
  1526.         }
  1527.       }
  1528.  
  1529.       /* Clear all the static flags */
  1530.       __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS);
  1531.  
  1532.       hsd->State = HAL_SD_STATE_READY;
  1533.       hsd->Context = SD_CONTEXT_NONE;
  1534.       if(((context & SD_CONTEXT_READ_SINGLE_BLOCK) != 0U) || ((context & SD_CONTEXT_READ_MULTIPLE_BLOCK) != 0U))
  1535.       {
  1536. #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U)
  1537.         hsd->RxCpltCallback(hsd);
  1538. #else
  1539.         HAL_SD_RxCpltCallback(hsd);
  1540. #endif /* USE_HAL_SD_REGISTER_CALLBACKS */
  1541.       }
  1542.       else
  1543.       {
  1544. #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U)
  1545.         hsd->TxCpltCallback(hsd);
  1546. #else
  1547.         HAL_SD_TxCpltCallback(hsd);
  1548. #endif /* USE_HAL_SD_REGISTER_CALLBACKS */
  1549.       }
  1550.     }
  1551.     else if((context & SD_CONTEXT_DMA) != 0U)
  1552.     {
  1553.       if((context & SD_CONTEXT_WRITE_MULTIPLE_BLOCK) != 0U)
  1554.       {
  1555.         errorstate = SDMMC_CmdStopTransfer(hsd->Instance);
  1556.         if(errorstate != HAL_SD_ERROR_NONE)
  1557.         {
  1558.           hsd->ErrorCode |= errorstate;
  1559. #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U)
  1560.           hsd->ErrorCallback(hsd);
  1561. #else
  1562.           HAL_SD_ErrorCallback(hsd);
  1563. #endif /* USE_HAL_SD_REGISTER_CALLBACKS */
  1564.         }
  1565.       }
  1566.       if(((context & SD_CONTEXT_READ_SINGLE_BLOCK) == 0U) && ((context & SD_CONTEXT_READ_MULTIPLE_BLOCK) == 0U))
  1567.       {
  1568.         /* Disable the DMA transfer for transmit request by setting the DMAEN bit
  1569.         in the SD DCTRL register */
  1570.         hsd->Instance->DCTRL &= (uint32_t)~((uint32_t)SDIO_DCTRL_DMAEN);
  1571.  
  1572.         hsd->State = HAL_SD_STATE_READY;
  1573.  
  1574. #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U)
  1575.         hsd->TxCpltCallback(hsd);
  1576. #else
  1577.         HAL_SD_TxCpltCallback(hsd);
  1578. #endif /* USE_HAL_SD_REGISTER_CALLBACKS */
  1579.       }
  1580.     }
  1581.     else
  1582.     {
  1583.       /* Nothing to do */
  1584.     }
  1585.   }
  1586.  
  1587.   else if((__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_TXFIFOHE) != RESET) && ((context & SD_CONTEXT_IT) != 0U))
  1588.   {
  1589.     SD_Write_IT(hsd);
  1590.   }
  1591.  
  1592.   else if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DCRCFAIL | SDIO_FLAG_DTIMEOUT | SDIO_FLAG_RXOVERR | SDIO_FLAG_TXUNDERR | SDIO_FLAG_STBITERR) != RESET)
  1593.   {
  1594.     /* Set Error code */
  1595.     if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DCRCFAIL) != RESET)
  1596.     {
  1597.       hsd->ErrorCode |= HAL_SD_ERROR_DATA_CRC_FAIL;
  1598.     }
  1599.     if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DTIMEOUT) != RESET)
  1600.     {
  1601.       hsd->ErrorCode |= HAL_SD_ERROR_DATA_TIMEOUT;
  1602.     }
  1603.     if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXOVERR) != RESET)
  1604.     {
  1605.       hsd->ErrorCode |= HAL_SD_ERROR_RX_OVERRUN;
  1606.     }
  1607.     if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_TXUNDERR) != RESET)
  1608.     {
  1609.       hsd->ErrorCode |= HAL_SD_ERROR_TX_UNDERRUN;
  1610.     }
  1611.     if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_STBITERR) != RESET)
  1612.     {
  1613.       hsd->ErrorCode |= HAL_SD_ERROR_DATA_TIMEOUT;
  1614.     }
  1615.  
  1616.     /* Clear All flags */
  1617.     __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS | SDIO_FLAG_STBITERR);
  1618.  
  1619.     /* Disable all interrupts */
  1620.     __HAL_SD_DISABLE_IT(hsd, SDIO_IT_DATAEND | SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT|\
  1621.                              SDIO_IT_TXUNDERR| SDIO_IT_RXOVERR | SDIO_IT_STBITERR);
  1622.  
  1623.     hsd->ErrorCode |= SDMMC_CmdStopTransfer(hsd->Instance);
  1624.  
  1625.     if((context & SD_CONTEXT_IT) != 0U)
  1626.     {
  1627.       /* Set the SD state to ready to be able to start again the process */
  1628.       hsd->State = HAL_SD_STATE_READY;
  1629.       hsd->Context = SD_CONTEXT_NONE;
  1630. #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U)
  1631.       hsd->ErrorCallback(hsd);
  1632. #else
  1633.       HAL_SD_ErrorCallback(hsd);
  1634. #endif /* USE_HAL_SD_REGISTER_CALLBACKS */
  1635.     }
  1636.     else if((context & SD_CONTEXT_DMA) != 0U)
  1637.     {
  1638.       /* Abort the SD DMA channel */
  1639.       if(((context & SD_CONTEXT_WRITE_SINGLE_BLOCK) != 0U) || ((context & SD_CONTEXT_WRITE_MULTIPLE_BLOCK) != 0U))
  1640.       {
  1641.         /* Set the DMA Tx abort callback */
  1642.         hsd->hdmatx->XferAbortCallback = SD_DMATxAbort;
  1643.         /* Abort DMA in IT mode */
  1644.         if(HAL_DMA_Abort_IT(hsd->hdmatx) != HAL_OK)
  1645.         {
  1646.           SD_DMATxAbort(hsd->hdmatx);
  1647.         }
  1648.       }
  1649.       else if(((context & SD_CONTEXT_READ_SINGLE_BLOCK) != 0U) || ((context & SD_CONTEXT_READ_MULTIPLE_BLOCK) != 0U))
  1650.       {
  1651.         /* Set the DMA Rx abort callback */
  1652.         hsd->hdmarx->XferAbortCallback = SD_DMARxAbort;
  1653.         /* Abort DMA in IT mode */
  1654.         if(HAL_DMA_Abort_IT(hsd->hdmarx) != HAL_OK)
  1655.         {
  1656.           SD_DMARxAbort(hsd->hdmarx);
  1657.         }
  1658.       }
  1659.       else
  1660.       {
  1661.         hsd->ErrorCode = HAL_SD_ERROR_NONE;
  1662.         hsd->State = HAL_SD_STATE_READY;
  1663.         hsd->Context = SD_CONTEXT_NONE;
  1664. #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U)
  1665.         hsd->AbortCpltCallback(hsd);
  1666. #else
  1667.         HAL_SD_AbortCallback(hsd);
  1668. #endif /* USE_HAL_SD_REGISTER_CALLBACKS */
  1669.       }
  1670.     }
  1671.     else
  1672.     {
  1673.       /* Nothing to do */
  1674.     }
  1675.   }
  1676.   else
  1677.   {
  1678.     /* Nothing to do */
  1679.   }
  1680. }
  1681.  
  1682. /**
  1683.   * @brief return the SD state
  1684.   * @param hsd: Pointer to sd handle
  1685.   * @retval HAL state
  1686.   */
  1687. HAL_SD_StateTypeDef HAL_SD_GetState(SD_HandleTypeDef *hsd)
  1688. {
  1689.   return hsd->State;
  1690. }
  1691.  
  1692. /**
  1693. * @brief  Return the SD error code
  1694. * @param  hsd : Pointer to a SD_HandleTypeDef structure that contains
  1695.   *              the configuration information.
  1696. * @retval SD Error Code
  1697. */
  1698. uint32_t HAL_SD_GetError(SD_HandleTypeDef *hsd)
  1699. {
  1700.   return hsd->ErrorCode;
  1701. }
  1702.  
  1703. /**
  1704.   * @brief Tx Transfer completed callbacks
  1705.   * @param hsd: Pointer to SD handle
  1706.   * @retval None
  1707.   */
  1708. __weak void HAL_SD_TxCpltCallback(SD_HandleTypeDef *hsd)
  1709. {
  1710.   /* Prevent unused argument(s) compilation warning */
  1711.   UNUSED(hsd);
  1712.  
  1713.   /* NOTE : This function should not be modified, when the callback is needed,
  1714.             the HAL_SD_TxCpltCallback can be implemented in the user file
  1715.    */
  1716. }
  1717.  
  1718. /**
  1719.   * @brief Rx Transfer completed callbacks
  1720.   * @param hsd: Pointer SD handle
  1721.   * @retval None
  1722.   */
  1723. __weak void HAL_SD_RxCpltCallback(SD_HandleTypeDef *hsd)
  1724. {
  1725.   /* Prevent unused argument(s) compilation warning */
  1726.   UNUSED(hsd);
  1727.  
  1728.   /* NOTE : This function should not be modified, when the callback is needed,
  1729.             the HAL_SD_RxCpltCallback can be implemented in the user file
  1730.    */
  1731. }
  1732.  
  1733. /**
  1734.   * @brief SD error callbacks
  1735.   * @param hsd: Pointer SD handle
  1736.   * @retval None
  1737.   */
  1738. __weak void HAL_SD_ErrorCallback(SD_HandleTypeDef *hsd)
  1739. {
  1740.   /* Prevent unused argument(s) compilation warning */
  1741.   UNUSED(hsd);
  1742.  
  1743.   /* NOTE : This function should not be modified, when the callback is needed,
  1744.             the HAL_SD_ErrorCallback can be implemented in the user file
  1745.    */
  1746. }
  1747.  
  1748. /**
  1749.   * @brief SD Abort callbacks
  1750.   * @param hsd: Pointer SD handle
  1751.   * @retval None
  1752.   */
  1753. __weak void HAL_SD_AbortCallback(SD_HandleTypeDef *hsd)
  1754. {
  1755.   /* Prevent unused argument(s) compilation warning */
  1756.   UNUSED(hsd);
  1757.  
  1758.   /* NOTE : This function should not be modified, when the callback is needed,
  1759.             the HAL_SD_AbortCallback can be implemented in the user file
  1760.    */
  1761. }
  1762.  
  1763. #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U)
  1764. /**
  1765.   * @brief  Register a User SD Callback
  1766.   *         To be used instead of the weak (surcharged) predefined callback
  1767.   * @param hsd : SD handle
  1768.   * @param CallbackID : ID of the callback to be registered
  1769.   *        This parameter can be one of the following values:
  1770.   *          @arg @ref HAL_SD_TX_CPLT_CB_ID    SD Tx Complete Callback ID
  1771.   *          @arg @ref HAL_SD_RX_CPLT_CB_ID    SD Rx Complete Callback ID
  1772.   *          @arg @ref HAL_SD_ERROR_CB_ID      SD Error Callback ID
  1773.   *          @arg @ref HAL_SD_ABORT_CB_ID      SD Abort Callback ID
  1774.   *          @arg @ref HAL_SD_MSP_INIT_CB_ID   SD MspInit Callback ID
  1775.   *          @arg @ref HAL_SD_MSP_DEINIT_CB_ID SD MspDeInit Callback ID
  1776.   * @param pCallback : pointer to the Callback function
  1777.   * @retval status
  1778.   */
  1779. HAL_StatusTypeDef HAL_SD_RegisterCallback(SD_HandleTypeDef *hsd, HAL_SD_CallbackIDTypeDef CallbackID, pSD_CallbackTypeDef pCallback)
  1780. {
  1781.   HAL_StatusTypeDef status = HAL_OK;
  1782.  
  1783.   if(pCallback == NULL)
  1784.   {
  1785.     /* Update the error code */
  1786.     hsd->ErrorCode |= HAL_SD_ERROR_INVALID_CALLBACK;
  1787.     return HAL_ERROR;
  1788.   }
  1789.  
  1790.   /* Process locked */
  1791.   __HAL_LOCK(hsd);
  1792.  
  1793.   if(hsd->State == HAL_SD_STATE_READY)
  1794.   {
  1795.     switch (CallbackID)
  1796.     {
  1797.     case HAL_SD_TX_CPLT_CB_ID :
  1798.       hsd->TxCpltCallback = pCallback;
  1799.       break;
  1800.     case HAL_SD_RX_CPLT_CB_ID :
  1801.       hsd->RxCpltCallback = pCallback;
  1802.       break;
  1803.     case HAL_SD_ERROR_CB_ID :
  1804.       hsd->ErrorCallback = pCallback;
  1805.       break;
  1806.     case HAL_SD_ABORT_CB_ID :
  1807.       hsd->AbortCpltCallback = pCallback;
  1808.       break;
  1809.     case HAL_SD_MSP_INIT_CB_ID :
  1810.       hsd->MspInitCallback = pCallback;
  1811.       break;
  1812.     case HAL_SD_MSP_DEINIT_CB_ID :
  1813.       hsd->MspDeInitCallback = pCallback;
  1814.       break;
  1815.     default :
  1816.       /* Update the error code */
  1817.       hsd->ErrorCode |= HAL_SD_ERROR_INVALID_CALLBACK;
  1818.       /* update return status */
  1819.       status =  HAL_ERROR;
  1820.       break;
  1821.     }
  1822.   }
  1823.   else if (hsd->State == HAL_SD_STATE_RESET)
  1824.   {
  1825.     switch (CallbackID)
  1826.     {
  1827.     case HAL_SD_MSP_INIT_CB_ID :
  1828.       hsd->MspInitCallback = pCallback;
  1829.       break;
  1830.     case HAL_SD_MSP_DEINIT_CB_ID :
  1831.       hsd->MspDeInitCallback = pCallback;
  1832.       break;
  1833.     default :
  1834.       /* Update the error code */
  1835.       hsd->ErrorCode |= HAL_SD_ERROR_INVALID_CALLBACK;
  1836.       /* update return status */
  1837.       status =  HAL_ERROR;
  1838.       break;
  1839.     }
  1840.   }
  1841.   else
  1842.   {
  1843.     /* Update the error code */
  1844.     hsd->ErrorCode |= HAL_SD_ERROR_INVALID_CALLBACK;
  1845.     /* update return status */
  1846.     status =  HAL_ERROR;
  1847.   }
  1848.  
  1849.   /* Release Lock */
  1850.   __HAL_UNLOCK(hsd);
  1851.   return status;
  1852. }
  1853.  
  1854. /**
  1855.   * @brief  Unregister a User SD Callback
  1856.   *         SD Callback is redirected to the weak (surcharged) predefined callback
  1857.   * @param hsd : SD handle
  1858.   * @param CallbackID : ID of the callback to be unregistered
  1859.   *        This parameter can be one of the following values:
  1860.   *          @arg @ref HAL_SD_TX_CPLT_CB_ID    SD Tx Complete Callback ID
  1861.   *          @arg @ref HAL_SD_RX_CPLT_CB_ID    SD Rx Complete Callback ID
  1862.   *          @arg @ref HAL_SD_ERROR_CB_ID      SD Error Callback ID
  1863.   *          @arg @ref HAL_SD_ABORT_CB_ID      SD Abort Callback ID
  1864.   *          @arg @ref HAL_SD_MSP_INIT_CB_ID   SD MspInit Callback ID
  1865.   *          @arg @ref HAL_SD_MSP_DEINIT_CB_ID SD MspDeInit Callback ID
  1866.   * @retval status
  1867.   */
  1868. HAL_StatusTypeDef HAL_SD_UnRegisterCallback(SD_HandleTypeDef *hsd, HAL_SD_CallbackIDTypeDef CallbackID)
  1869. {
  1870.   HAL_StatusTypeDef status = HAL_OK;
  1871.  
  1872.   /* Process locked */
  1873.   __HAL_LOCK(hsd);
  1874.  
  1875.   if(hsd->State == HAL_SD_STATE_READY)
  1876.   {
  1877.     switch (CallbackID)
  1878.     {
  1879.     case HAL_SD_TX_CPLT_CB_ID :
  1880.       hsd->TxCpltCallback = HAL_SD_TxCpltCallback;
  1881.       break;
  1882.     case HAL_SD_RX_CPLT_CB_ID :
  1883.       hsd->RxCpltCallback = HAL_SD_RxCpltCallback;
  1884.       break;
  1885.     case HAL_SD_ERROR_CB_ID :
  1886.       hsd->ErrorCallback = HAL_SD_ErrorCallback;
  1887.       break;
  1888.     case HAL_SD_ABORT_CB_ID :
  1889.       hsd->AbortCpltCallback = HAL_SD_AbortCallback;
  1890.       break;
  1891.     case HAL_SD_MSP_INIT_CB_ID :
  1892.       hsd->MspInitCallback = HAL_SD_MspInit;
  1893.       break;
  1894.     case HAL_SD_MSP_DEINIT_CB_ID :
  1895.       hsd->MspDeInitCallback = HAL_SD_MspDeInit;
  1896.       break;
  1897.     default :
  1898.       /* Update the error code */
  1899.       hsd->ErrorCode |= HAL_SD_ERROR_INVALID_CALLBACK;
  1900.       /* update return status */
  1901.       status =  HAL_ERROR;
  1902.       break;
  1903.     }
  1904.   }
  1905.   else if (hsd->State == HAL_SD_STATE_RESET)
  1906.   {
  1907.     switch (CallbackID)
  1908.     {
  1909.     case HAL_SD_MSP_INIT_CB_ID :
  1910.       hsd->MspInitCallback = HAL_SD_MspInit;
  1911.       break;
  1912.     case HAL_SD_MSP_DEINIT_CB_ID :
  1913.       hsd->MspDeInitCallback = HAL_SD_MspDeInit;
  1914.       break;
  1915.     default :
  1916.       /* Update the error code */
  1917.       hsd->ErrorCode |= HAL_SD_ERROR_INVALID_CALLBACK;
  1918.       /* update return status */
  1919.       status =  HAL_ERROR;
  1920.       break;
  1921.     }
  1922.   }
  1923.   else
  1924.   {
  1925.     /* Update the error code */
  1926.     hsd->ErrorCode |= HAL_SD_ERROR_INVALID_CALLBACK;
  1927.     /* update return status */
  1928.     status =  HAL_ERROR;
  1929.   }
  1930.  
  1931.   /* Release Lock */
  1932.   __HAL_UNLOCK(hsd);
  1933.   return status;
  1934. }
  1935. #endif /* USE_HAL_SD_REGISTER_CALLBACKS */
  1936.  
  1937. /**
  1938.   * @}
  1939.   */
  1940.  
  1941. /** @addtogroup SD_Exported_Functions_Group3
  1942.  *  @brief   management functions
  1943.  *
  1944. @verbatim
  1945.   ==============================================================================
  1946.                       ##### Peripheral Control functions #####
  1947.   ==============================================================================
  1948.   [..]
  1949.     This subsection provides a set of functions allowing to control the SD card
  1950.     operations and get the related information
  1951.  
  1952. @endverbatim
  1953.   * @{
  1954.   */
  1955.  
  1956. /**
  1957.   * @brief  Returns information the information of the card which are stored on
  1958.   *         the CID register.
  1959.   * @param  hsd: Pointer to SD handle
  1960.   * @param  pCID: Pointer to a HAL_SD_CardCIDTypeDef structure that  
  1961.   *         contains all CID register parameters
  1962.   * @retval HAL status
  1963.   */
  1964. HAL_StatusTypeDef HAL_SD_GetCardCID(SD_HandleTypeDef *hsd, HAL_SD_CardCIDTypeDef *pCID)
  1965. {
  1966.   pCID->ManufacturerID = (uint8_t)((hsd->CID[0] & 0xFF000000U) >> 24U);
  1967.  
  1968.   pCID->OEM_AppliID = (uint16_t)((hsd->CID[0] & 0x00FFFF00U) >> 8U);
  1969.  
  1970.   pCID->ProdName1 = (((hsd->CID[0] & 0x000000FFU) << 24U) | ((hsd->CID[1] & 0xFFFFFF00U) >> 8U));
  1971.  
  1972.   pCID->ProdName2 = (uint8_t)(hsd->CID[1] & 0x000000FFU);
  1973.  
  1974.   pCID->ProdRev = (uint8_t)((hsd->CID[2] & 0xFF000000U) >> 24U);
  1975.  
  1976.   pCID->ProdSN = (((hsd->CID[2] & 0x00FFFFFFU) << 8U) | ((hsd->CID[3] & 0xFF000000U) >> 24U));
  1977.  
  1978.   pCID->Reserved1 = (uint8_t)((hsd->CID[3] & 0x00F00000U) >> 20U);
  1979.  
  1980.   pCID->ManufactDate = (uint16_t)((hsd->CID[3] & 0x000FFF00U) >> 8U);
  1981.  
  1982.   pCID->CID_CRC = (uint8_t)((hsd->CID[3] & 0x000000FEU) >> 1U);
  1983.  
  1984.   pCID->Reserved2 = 1U;
  1985.  
  1986.   return HAL_OK;
  1987. }
  1988.  
  1989. /**
  1990.   * @brief  Returns information the information of the card which are stored on
  1991.   *         the CSD register.
  1992.   * @param  hsd: Pointer to SD handle
  1993.   * @param  pCSD: Pointer to a HAL_SD_CardCSDTypeDef structure that  
  1994.   *         contains all CSD register parameters
  1995.   * @retval HAL status
  1996.   */
  1997. HAL_StatusTypeDef HAL_SD_GetCardCSD(SD_HandleTypeDef *hsd, HAL_SD_CardCSDTypeDef *pCSD)
  1998. {
  1999.   pCSD->CSDStruct = (uint8_t)((hsd->CSD[0] & 0xC0000000U) >> 30U);
  2000.  
  2001.   pCSD->SysSpecVersion = (uint8_t)((hsd->CSD[0] & 0x3C000000U) >> 26U);
  2002.  
  2003.   pCSD->Reserved1 = (uint8_t)((hsd->CSD[0] & 0x03000000U) >> 24U);
  2004.  
  2005.   pCSD->TAAC = (uint8_t)((hsd->CSD[0] & 0x00FF0000U) >> 16U);
  2006.  
  2007.   pCSD->NSAC = (uint8_t)((hsd->CSD[0] & 0x0000FF00U) >> 8U);
  2008.  
  2009.   pCSD->MaxBusClkFrec = (uint8_t)(hsd->CSD[0] & 0x000000FFU);
  2010.  
  2011.   pCSD->CardComdClasses = (uint16_t)((hsd->CSD[1] & 0xFFF00000U) >> 20U);
  2012.  
  2013.   pCSD->RdBlockLen = (uint8_t)((hsd->CSD[1] & 0x000F0000U) >> 16U);
  2014.  
  2015.   pCSD->PartBlockRead   = (uint8_t)((hsd->CSD[1] & 0x00008000U) >> 15U);
  2016.  
  2017.   pCSD->WrBlockMisalign = (uint8_t)((hsd->CSD[1] & 0x00004000U) >> 14U);
  2018.  
  2019.   pCSD->RdBlockMisalign = (uint8_t)((hsd->CSD[1] & 0x00002000U) >> 13U);
  2020.  
  2021.   pCSD->DSRImpl = (uint8_t)((hsd->CSD[1] & 0x00001000U) >> 12U);
  2022.  
  2023.   pCSD->Reserved2 = 0U; /*!< Reserved */
  2024.  
  2025.   if(hsd->SdCard.CardType == CARD_SDSC)
  2026.   {
  2027.     pCSD->DeviceSize = (((hsd->CSD[1] & 0x000003FFU) << 2U) | ((hsd->CSD[2] & 0xC0000000U) >> 30U));
  2028.  
  2029.     pCSD->MaxRdCurrentVDDMin = (uint8_t)((hsd->CSD[2] & 0x38000000U) >> 27U);
  2030.  
  2031.     pCSD->MaxRdCurrentVDDMax = (uint8_t)((hsd->CSD[2] & 0x07000000U) >> 24U);
  2032.  
  2033.     pCSD->MaxWrCurrentVDDMin = (uint8_t)((hsd->CSD[2] & 0x00E00000U) >> 21U);
  2034.  
  2035.     pCSD->MaxWrCurrentVDDMax = (uint8_t)((hsd->CSD[2] & 0x001C0000U) >> 18U);
  2036.  
  2037.     pCSD->DeviceSizeMul = (uint8_t)((hsd->CSD[2] & 0x00038000U) >> 15U);
  2038.  
  2039.     hsd->SdCard.BlockNbr  = (pCSD->DeviceSize + 1U) ;
  2040.     hsd->SdCard.BlockNbr *= (1UL << ((pCSD->DeviceSizeMul & 0x07U) + 2U));
  2041.     hsd->SdCard.BlockSize = (1UL << (pCSD->RdBlockLen & 0x0FU));
  2042.  
  2043.     hsd->SdCard.LogBlockNbr =  (hsd->SdCard.BlockNbr) * ((hsd->SdCard.BlockSize) / 512U);
  2044.     hsd->SdCard.LogBlockSize = 512U;
  2045.   }
  2046.   else if(hsd->SdCard.CardType == CARD_SDHC_SDXC)
  2047.   {
  2048.     /* Byte 7 */
  2049.     pCSD->DeviceSize = (((hsd->CSD[1] & 0x0000003FU) << 16U) | ((hsd->CSD[2] & 0xFFFF0000U) >> 16U));
  2050.  
  2051.     hsd->SdCard.BlockNbr = ((pCSD->DeviceSize + 1U) * 1024U);
  2052.     hsd->SdCard.LogBlockNbr = hsd->SdCard.BlockNbr;
  2053.     hsd->SdCard.BlockSize = 512U;
  2054.     hsd->SdCard.LogBlockSize = hsd->SdCard.BlockSize;
  2055.   }
  2056.   else
  2057.   {
  2058.     /* Clear all the static flags */
  2059.     __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  2060.     hsd->ErrorCode |= HAL_SD_ERROR_UNSUPPORTED_FEATURE;
  2061.     hsd->State = HAL_SD_STATE_READY;
  2062.     return HAL_ERROR;
  2063.   }
  2064.  
  2065.   pCSD->EraseGrSize = (uint8_t)((hsd->CSD[2] & 0x00004000U) >> 14U);
  2066.  
  2067.   pCSD->EraseGrMul = (uint8_t)((hsd->CSD[2] & 0x00003F80U) >> 7U);
  2068.  
  2069.   pCSD->WrProtectGrSize = (uint8_t)(hsd->CSD[2] & 0x0000007FU);
  2070.  
  2071.   pCSD->WrProtectGrEnable = (uint8_t)((hsd->CSD[3] & 0x80000000U) >> 31U);
  2072.  
  2073.   pCSD->ManDeflECC = (uint8_t)((hsd->CSD[3] & 0x60000000U) >> 29U);
  2074.  
  2075.   pCSD->WrSpeedFact = (uint8_t)((hsd->CSD[3] & 0x1C000000U) >> 26U);
  2076.  
  2077.   pCSD->MaxWrBlockLen= (uint8_t)((hsd->CSD[3] & 0x03C00000U) >> 22U);
  2078.  
  2079.   pCSD->WriteBlockPaPartial = (uint8_t)((hsd->CSD[3] & 0x00200000U) >> 21U);
  2080.  
  2081.   pCSD->Reserved3 = 0;
  2082.  
  2083.   pCSD->ContentProtectAppli = (uint8_t)((hsd->CSD[3] & 0x00010000U) >> 16U);
  2084.  
  2085.   pCSD->FileFormatGroup = (uint8_t)((hsd->CSD[3] & 0x00008000U) >> 15U);
  2086.  
  2087.   pCSD->CopyFlag = (uint8_t)((hsd->CSD[3] & 0x00004000U) >> 14U);
  2088.  
  2089.   pCSD->PermWrProtect = (uint8_t)((hsd->CSD[3] & 0x00002000U) >> 13U);
  2090.  
  2091.   pCSD->TempWrProtect = (uint8_t)((hsd->CSD[3] & 0x00001000U) >> 12U);
  2092.  
  2093.   pCSD->FileFormat = (uint8_t)((hsd->CSD[3] & 0x00000C00U) >> 10U);
  2094.  
  2095.   pCSD->ECC= (uint8_t)((hsd->CSD[3] & 0x00000300U) >> 8U);
  2096.  
  2097.   pCSD->CSD_CRC = (uint8_t)((hsd->CSD[3] & 0x000000FEU) >> 1U);
  2098.  
  2099.   pCSD->Reserved4 = 1;
  2100.  
  2101.   return HAL_OK;
  2102. }
  2103.  
  2104. /**
  2105.   * @brief  Gets the SD status info.
  2106.   * @param  hsd: Pointer to SD handle
  2107.   * @param  pStatus: Pointer to the HAL_SD_CardStatusTypeDef structure that
  2108.   *         will contain the SD card status information
  2109.   * @retval HAL status
  2110.   */
  2111. HAL_StatusTypeDef HAL_SD_GetCardStatus(SD_HandleTypeDef *hsd, HAL_SD_CardStatusTypeDef *pStatus)
  2112. {
  2113.   uint32_t sd_status[16];
  2114.   uint32_t errorstate;
  2115.   HAL_StatusTypeDef status = HAL_OK;
  2116.  
  2117.   errorstate = SD_SendSDStatus(hsd, sd_status);
  2118.   if(errorstate != HAL_SD_ERROR_NONE)
  2119.   {
  2120.     /* Clear all the static flags */
  2121.     __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  2122.     hsd->ErrorCode |= errorstate;
  2123.     hsd->State = HAL_SD_STATE_READY;
  2124.     status = HAL_ERROR;
  2125.   }
  2126.   else
  2127.   {
  2128.     pStatus->DataBusWidth = (uint8_t)((sd_status[0] & 0xC0U) >> 6U);
  2129.  
  2130.     pStatus->SecuredMode = (uint8_t)((sd_status[0] & 0x20U) >> 5U);
  2131.  
  2132.     pStatus->CardType = (uint16_t)(((sd_status[0] & 0x00FF0000U) >> 8U) | ((sd_status[0] & 0xFF000000U) >> 24U));
  2133.  
  2134.     pStatus->ProtectedAreaSize = (((sd_status[1] & 0xFFU) << 24U)    | ((sd_status[1] & 0xFF00U) << 8U) |
  2135.                                   ((sd_status[1] & 0xFF0000U) >> 8U) | ((sd_status[1] & 0xFF000000U) >> 24U));
  2136.  
  2137.     pStatus->SpeedClass = (uint8_t)(sd_status[2] & 0xFFU);
  2138.  
  2139.     pStatus->PerformanceMove = (uint8_t)((sd_status[2] & 0xFF00U) >> 8U);
  2140.  
  2141.     pStatus->AllocationUnitSize = (uint8_t)((sd_status[2] & 0xF00000U) >> 20U);
  2142.  
  2143.     pStatus->EraseSize = (uint16_t)(((sd_status[2] & 0xFF000000U) >> 16U) | (sd_status[3] & 0xFFU));
  2144.  
  2145.     pStatus->EraseTimeout = (uint8_t)((sd_status[3] & 0xFC00U) >> 10U);
  2146.  
  2147.     pStatus->EraseOffset = (uint8_t)((sd_status[3] & 0x0300U) >> 8U);
  2148.   }
  2149.  
  2150.   /* Set Block Size for Card */
  2151.   errorstate = SDMMC_CmdBlockLength(hsd->Instance, BLOCKSIZE);
  2152.   if(errorstate != HAL_SD_ERROR_NONE)
  2153.   {
  2154.     /* Clear all the static flags */
  2155.     __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  2156.     hsd->ErrorCode = errorstate;
  2157.     hsd->State = HAL_SD_STATE_READY;
  2158.     status = HAL_ERROR;
  2159.   }
  2160.  
  2161.   return status;
  2162. }
  2163.  
  2164. /**
  2165.   * @brief  Gets the SD card info.
  2166.   * @param  hsd: Pointer to SD handle
  2167.   * @param  pCardInfo: Pointer to the HAL_SD_CardInfoTypeDef structure that
  2168.   *         will contain the SD card status information
  2169.   * @retval HAL status
  2170.   */
  2171. HAL_StatusTypeDef HAL_SD_GetCardInfo(SD_HandleTypeDef *hsd, HAL_SD_CardInfoTypeDef *pCardInfo)
  2172. {
  2173.   pCardInfo->CardType     = (uint32_t)(hsd->SdCard.CardType);
  2174.   pCardInfo->CardVersion  = (uint32_t)(hsd->SdCard.CardVersion);
  2175.   pCardInfo->Class        = (uint32_t)(hsd->SdCard.Class);
  2176.   pCardInfo->RelCardAdd   = (uint32_t)(hsd->SdCard.RelCardAdd);
  2177.   pCardInfo->BlockNbr     = (uint32_t)(hsd->SdCard.BlockNbr);
  2178.   pCardInfo->BlockSize    = (uint32_t)(hsd->SdCard.BlockSize);
  2179.   pCardInfo->LogBlockNbr  = (uint32_t)(hsd->SdCard.LogBlockNbr);
  2180.   pCardInfo->LogBlockSize = (uint32_t)(hsd->SdCard.LogBlockSize);
  2181.  
  2182.   return HAL_OK;
  2183. }
  2184.  
  2185. /**
  2186.   * @brief  Enables wide bus operation for the requested card if supported by
  2187.   *         card.
  2188.   * @param  hsd: Pointer to SD handle
  2189.   * @param  WideMode: Specifies the SD card wide bus mode
  2190.   *          This parameter can be one of the following values:
  2191.   *            @arg SDIO_BUS_WIDE_8B: 8-bit data transfer
  2192.   *            @arg SDIO_BUS_WIDE_4B: 4-bit data transfer
  2193.   *            @arg SDIO_BUS_WIDE_1B: 1-bit data transfer
  2194.   * @retval HAL status
  2195.   */
  2196. HAL_StatusTypeDef HAL_SD_ConfigWideBusOperation(SD_HandleTypeDef *hsd, uint32_t WideMode)
  2197. {
  2198.   SDIO_InitTypeDef Init;
  2199.   uint32_t errorstate;
  2200.   HAL_StatusTypeDef status = HAL_OK;
  2201.  
  2202.   /* Check the parameters */
  2203.   assert_param(IS_SDIO_BUS_WIDE(WideMode));
  2204.  
  2205.   /* Change State */
  2206.   hsd->State = HAL_SD_STATE_BUSY;
  2207.  
  2208.   if(hsd->SdCard.CardType != CARD_SECURED)
  2209.   {
  2210.     if(WideMode == SDIO_BUS_WIDE_8B)
  2211.     {
  2212.       hsd->ErrorCode |= HAL_SD_ERROR_UNSUPPORTED_FEATURE;
  2213.     }
  2214.     else if(WideMode == SDIO_BUS_WIDE_4B)
  2215.     {
  2216.       errorstate = SD_WideBus_Enable(hsd);
  2217.  
  2218.       hsd->ErrorCode |= errorstate;
  2219.     }
  2220.     else if(WideMode == SDIO_BUS_WIDE_1B)
  2221.     {
  2222.       errorstate = SD_WideBus_Disable(hsd);
  2223.  
  2224.       hsd->ErrorCode |= errorstate;
  2225.     }
  2226.     else
  2227.     {
  2228.       /* WideMode is not a valid argument*/
  2229.       hsd->ErrorCode |= HAL_SD_ERROR_PARAM;
  2230.     }
  2231.   }
  2232.   else
  2233.   {
  2234.     /* MMC Card does not support this feature */
  2235.     hsd->ErrorCode |= HAL_SD_ERROR_UNSUPPORTED_FEATURE;
  2236.   }
  2237.  
  2238.   if(hsd->ErrorCode != HAL_SD_ERROR_NONE)
  2239.   {
  2240.     /* Clear all the static flags */
  2241.     __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  2242.     hsd->State = HAL_SD_STATE_READY;
  2243.     status = HAL_ERROR;
  2244.   }
  2245.   else
  2246.   {
  2247.     /* Configure the SDIO peripheral */
  2248.     Init.ClockEdge           = hsd->Init.ClockEdge;
  2249.     Init.ClockBypass         = hsd->Init.ClockBypass;
  2250.     Init.ClockPowerSave      = hsd->Init.ClockPowerSave;
  2251.     Init.BusWide             = WideMode;
  2252.     Init.HardwareFlowControl = hsd->Init.HardwareFlowControl;
  2253.     Init.ClockDiv            = hsd->Init.ClockDiv;
  2254.     (void)SDIO_Init(hsd->Instance, Init);
  2255.   }
  2256.  
  2257.   /* Set Block Size for Card */
  2258.   errorstate = SDMMC_CmdBlockLength(hsd->Instance, BLOCKSIZE);
  2259.   if(errorstate != HAL_SD_ERROR_NONE)
  2260.   {
  2261.     /* Clear all the static flags */
  2262.     __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  2263.     hsd->ErrorCode |= errorstate;
  2264.     status = HAL_ERROR;
  2265.   }
  2266.  
  2267.   /* Change State */
  2268.   hsd->State = HAL_SD_STATE_READY;
  2269.  
  2270.   return status;
  2271. }
  2272.  
  2273. /**
  2274.   * @brief  Gets the current sd card data state.
  2275.   * @param  hsd: pointer to SD handle
  2276.   * @retval Card state
  2277.   */
  2278. HAL_SD_CardStateTypeDef HAL_SD_GetCardState(SD_HandleTypeDef *hsd)
  2279. {
  2280.   uint32_t cardstate;
  2281.   uint32_t errorstate;
  2282.   uint32_t resp1 = 0;
  2283.  
  2284.   errorstate = SD_SendStatus(hsd, &resp1);
  2285.   if(errorstate != HAL_SD_ERROR_NONE)
  2286.   {
  2287.     hsd->ErrorCode |= errorstate;
  2288.   }
  2289.  
  2290.   cardstate = ((resp1 >> 9U) & 0x0FU);
  2291.  
  2292.   return (HAL_SD_CardStateTypeDef)cardstate;
  2293. }
  2294.  
  2295. /**
  2296.   * @brief  Abort the current transfer and disable the SD.
  2297.   * @param  hsd: pointer to a SD_HandleTypeDef structure that contains
  2298.   *                the configuration information for SD module.
  2299.   * @retval HAL status
  2300.   */
  2301. HAL_StatusTypeDef HAL_SD_Abort(SD_HandleTypeDef *hsd)
  2302. {
  2303.   HAL_SD_CardStateTypeDef CardState;
  2304.   uint32_t context = hsd->Context;
  2305.  
  2306.   /* DIsable All interrupts */
  2307.   __HAL_SD_DISABLE_IT(hsd, SDIO_IT_DATAEND | SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT|\
  2308.                            SDIO_IT_TXUNDERR| SDIO_IT_RXOVERR);
  2309.  
  2310.   /* Clear All flags */
  2311.   __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS);
  2312.  
  2313.   CLEAR_BIT(hsd->Instance->DCTRL, SDIO_DCTRL_DTEN);
  2314.  
  2315.   if ((context & SD_CONTEXT_DMA) != 0U)
  2316.   {
  2317.     /* Disable the SD DMA request */
  2318.     hsd->Instance->DCTRL &= (uint32_t)~((uint32_t)SDIO_DCTRL_DMAEN);
  2319.  
  2320.     /* Abort the SD DMA Tx channel */
  2321.     if (((context & SD_CONTEXT_WRITE_SINGLE_BLOCK) != 0U) || ((context & SD_CONTEXT_WRITE_MULTIPLE_BLOCK) != 0U))
  2322.     {
  2323.       if(HAL_DMA_Abort(hsd->hdmatx) != HAL_OK)
  2324.       {
  2325.         hsd->ErrorCode |= HAL_SD_ERROR_DMA;
  2326.       }
  2327.     }
  2328.     /* Abort the SD DMA Rx channel */
  2329.     else if (((context & SD_CONTEXT_READ_SINGLE_BLOCK) != 0U) || ((context & SD_CONTEXT_READ_MULTIPLE_BLOCK) != 0U))
  2330.     {
  2331.       if(HAL_DMA_Abort(hsd->hdmarx) != HAL_OK)
  2332.       {
  2333.         hsd->ErrorCode |= HAL_SD_ERROR_DMA;
  2334.       }
  2335.     }
  2336.     else
  2337.     {
  2338.       /* Nothing to do */
  2339.     }
  2340.   }
  2341.  
  2342.   hsd->State = HAL_SD_STATE_READY;
  2343.  
  2344.   /* Initialize the SD operation */
  2345.   hsd->Context = SD_CONTEXT_NONE;
  2346.  
  2347.   CardState = HAL_SD_GetCardState(hsd);
  2348.   if((CardState == HAL_SD_CARD_RECEIVING) || (CardState == HAL_SD_CARD_SENDING))
  2349.   {
  2350.     hsd->ErrorCode = SDMMC_CmdStopTransfer(hsd->Instance);
  2351.   }
  2352.   if(hsd->ErrorCode != HAL_SD_ERROR_NONE)
  2353.   {
  2354.     return HAL_ERROR;
  2355.   }
  2356.   return HAL_OK;
  2357. }
  2358.  
  2359. /**
  2360.   * @brief  Abort the current transfer and disable the SD (IT mode).
  2361.   * @param  hsd: pointer to a SD_HandleTypeDef structure that contains
  2362.   *                the configuration information for SD module.
  2363.   * @retval HAL status
  2364.   */
  2365. HAL_StatusTypeDef HAL_SD_Abort_IT(SD_HandleTypeDef *hsd)
  2366. {
  2367.   HAL_SD_CardStateTypeDef CardState;
  2368.   uint32_t context = hsd->Context;
  2369.  
  2370.   /* Disable All interrupts */
  2371.   __HAL_SD_DISABLE_IT(hsd, SDIO_IT_DATAEND | SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT|\
  2372.                            SDIO_IT_TXUNDERR| SDIO_IT_RXOVERR);
  2373.  
  2374.   CLEAR_BIT(hsd->Instance->DCTRL, SDIO_DCTRL_DTEN);
  2375.  
  2376.   if ((context & SD_CONTEXT_DMA) != 0U)
  2377.   {
  2378.     /* Disable the SD DMA request */
  2379.     hsd->Instance->DCTRL &= (uint32_t)~((uint32_t)SDIO_DCTRL_DMAEN);
  2380.  
  2381.     /* Abort the SD DMA Tx channel */
  2382.     if (((context & SD_CONTEXT_WRITE_SINGLE_BLOCK) != 0U) || ((context & SD_CONTEXT_WRITE_MULTIPLE_BLOCK) != 0U))
  2383.     {
  2384.       hsd->hdmatx->XferAbortCallback = SD_DMATxAbort;
  2385.       if(HAL_DMA_Abort_IT(hsd->hdmatx) != HAL_OK)
  2386.       {
  2387.         hsd->hdmatx = NULL;
  2388.       }
  2389.     }
  2390.     /* Abort the SD DMA Rx channel */
  2391.     else if (((context & SD_CONTEXT_READ_SINGLE_BLOCK) != 0U) || ((context & SD_CONTEXT_READ_MULTIPLE_BLOCK) != 0U))
  2392.     {
  2393.       hsd->hdmarx->XferAbortCallback = SD_DMARxAbort;
  2394.       if(HAL_DMA_Abort_IT(hsd->hdmarx) != HAL_OK)
  2395.       {
  2396.         hsd->hdmarx = NULL;
  2397.       }
  2398.     }
  2399.     else
  2400.     {
  2401.       /* Nothing to do */
  2402.     }
  2403.   }
  2404.   /* No transfer ongoing on both DMA channels*/
  2405.   else
  2406.   {
  2407.     /* Clear All flags */
  2408.     __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS);
  2409.  
  2410.     CardState = HAL_SD_GetCardState(hsd);
  2411.     hsd->State = HAL_SD_STATE_READY;
  2412.     hsd->Context = SD_CONTEXT_NONE;
  2413.     if((CardState == HAL_SD_CARD_RECEIVING) || (CardState == HAL_SD_CARD_SENDING))
  2414.     {
  2415.       hsd->ErrorCode = SDMMC_CmdStopTransfer(hsd->Instance);
  2416.     }
  2417.     if(hsd->ErrorCode != HAL_SD_ERROR_NONE)
  2418.     {
  2419.       return HAL_ERROR;
  2420.     }
  2421.     else
  2422.     {
  2423. #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U)
  2424.       hsd->AbortCpltCallback(hsd);
  2425. #else
  2426.       HAL_SD_AbortCallback(hsd);
  2427. #endif /* USE_HAL_SD_REGISTER_CALLBACKS */
  2428.     }
  2429.   }
  2430.  
  2431.   return HAL_OK;
  2432. }
  2433.  
  2434. /**
  2435.   * @}
  2436.   */
  2437.  
  2438. /**
  2439.   * @}
  2440.   */
  2441.  
  2442. /* Private function ----------------------------------------------------------*/
  2443. /** @addtogroup SD_Private_Functions
  2444.   * @{
  2445.   */
  2446.  
  2447. /**
  2448.   * @brief  DMA SD transmit process complete callback
  2449.   * @param  hdma: DMA handle
  2450.   * @retval None
  2451.   */
  2452. static void SD_DMATransmitCplt(DMA_HandleTypeDef *hdma)
  2453. {
  2454.   SD_HandleTypeDef* hsd = (SD_HandleTypeDef* )(hdma->Parent);
  2455.  
  2456.   /* Enable DATAEND Interrupt */
  2457.   __HAL_SD_ENABLE_IT(hsd, (SDIO_IT_DATAEND));
  2458. }
  2459.  
  2460. /**
  2461.   * @brief  DMA SD receive process complete callback
  2462.   * @param  hdma: DMA handle
  2463.   * @retval None
  2464.   */
  2465. static void SD_DMAReceiveCplt(DMA_HandleTypeDef *hdma)
  2466. {
  2467.   SD_HandleTypeDef* hsd = (SD_HandleTypeDef* )(hdma->Parent);
  2468.   uint32_t errorstate;
  2469.  
  2470.   /* Send stop command in multiblock write */
  2471.   if(hsd->Context == (SD_CONTEXT_READ_MULTIPLE_BLOCK | SD_CONTEXT_DMA))
  2472.   {
  2473.     errorstate = SDMMC_CmdStopTransfer(hsd->Instance);
  2474.     if(errorstate != HAL_SD_ERROR_NONE)
  2475.     {
  2476.       hsd->ErrorCode |= errorstate;
  2477. #if (USE_HAL_SD_REGISTER_CALLBACKS == 1)
  2478.       hsd->ErrorCallback(hsd);
  2479. #else
  2480.       HAL_SD_ErrorCallback(hsd);
  2481. #endif
  2482.     }
  2483.   }
  2484.  
  2485.   /* Disable the DMA transfer for transmit request by setting the DMAEN bit
  2486.   in the SD DCTRL register */
  2487.   hsd->Instance->DCTRL &= (uint32_t)~((uint32_t)SDIO_DCTRL_DMAEN);
  2488.  
  2489.   /* Clear all the static flags */
  2490.   __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS);
  2491.  
  2492.   hsd->State = HAL_SD_STATE_READY;
  2493.   hsd->Context = SD_CONTEXT_NONE;
  2494.  
  2495. #if (USE_HAL_SD_REGISTER_CALLBACKS == 1)
  2496.   hsd->RxCpltCallback(hsd);
  2497. #else
  2498.   HAL_SD_RxCpltCallback(hsd);
  2499. #endif
  2500. }
  2501.  
  2502. /**
  2503.   * @brief  DMA SD communication error callback
  2504.   * @param  hdma: DMA handle
  2505.   * @retval None
  2506.   */
  2507. static void SD_DMAError(DMA_HandleTypeDef *hdma)
  2508. {
  2509.   SD_HandleTypeDef* hsd = (SD_HandleTypeDef* )(hdma->Parent);
  2510.   HAL_SD_CardStateTypeDef CardState;
  2511.   uint32_t RxErrorCode, TxErrorCode;
  2512.  
  2513.     RxErrorCode = hsd->hdmarx->ErrorCode;
  2514.     TxErrorCode = hsd->hdmatx->ErrorCode;  
  2515.     if((RxErrorCode == HAL_DMA_ERROR_TE) || (TxErrorCode == HAL_DMA_ERROR_TE))
  2516.     {
  2517.       /* Clear All flags */
  2518.       __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_FLAGS);
  2519.  
  2520.       /* Disable All interrupts */
  2521.       __HAL_SD_DISABLE_IT(hsd, SDIO_IT_DATAEND | SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT|\
  2522.         SDIO_IT_TXUNDERR| SDIO_IT_RXOVERR);
  2523.  
  2524.       hsd->ErrorCode |= HAL_SD_ERROR_DMA;
  2525.       CardState = HAL_SD_GetCardState(hsd);
  2526.       if((CardState == HAL_SD_CARD_RECEIVING) || (CardState == HAL_SD_CARD_SENDING))
  2527.       {
  2528.         hsd->ErrorCode |= SDMMC_CmdStopTransfer(hsd->Instance);
  2529.       }
  2530.  
  2531.       hsd->State= HAL_SD_STATE_READY;
  2532.       hsd->Context = SD_CONTEXT_NONE;
  2533.     }
  2534.  
  2535. #if (USE_HAL_SD_REGISTER_CALLBACKS == 1)
  2536.     hsd->ErrorCallback(hsd);
  2537. #else
  2538.     HAL_SD_ErrorCallback(hsd);
  2539. #endif
  2540. }
  2541.  
  2542. /**
  2543.   * @brief  DMA SD Tx Abort callback
  2544.   * @param  hdma: DMA handle
  2545.   * @retval None
  2546.   */
  2547. static void SD_DMATxAbort(DMA_HandleTypeDef *hdma)
  2548. {
  2549.   SD_HandleTypeDef* hsd = (SD_HandleTypeDef* )(hdma->Parent);
  2550.   HAL_SD_CardStateTypeDef CardState;
  2551.  
  2552.   /* Clear All flags */
  2553.   __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS);
  2554.  
  2555.   CardState = HAL_SD_GetCardState(hsd);
  2556.   hsd->State = HAL_SD_STATE_READY;
  2557.   hsd->Context = SD_CONTEXT_NONE;
  2558.   if((CardState == HAL_SD_CARD_RECEIVING) || (CardState == HAL_SD_CARD_SENDING))
  2559.   {
  2560.     hsd->ErrorCode |= SDMMC_CmdStopTransfer(hsd->Instance);
  2561.   }
  2562.  
  2563.   if(hsd->ErrorCode == HAL_SD_ERROR_NONE)
  2564.   {
  2565. #if (USE_HAL_SD_REGISTER_CALLBACKS == 1)
  2566.     hsd->AbortCpltCallback(hsd);
  2567. #else
  2568.     HAL_SD_AbortCallback(hsd);
  2569. #endif
  2570.   }
  2571.   else
  2572.   {
  2573. #if (USE_HAL_SD_REGISTER_CALLBACKS == 1)
  2574.     hsd->ErrorCallback(hsd);
  2575. #else
  2576.     HAL_SD_ErrorCallback(hsd);
  2577. #endif
  2578.   }
  2579. }
  2580.  
  2581. /**
  2582.   * @brief  DMA SD Rx Abort callback
  2583.   * @param  hdma: DMA handle
  2584.   * @retval None
  2585.   */
  2586. static void SD_DMARxAbort(DMA_HandleTypeDef *hdma)
  2587. {
  2588.   SD_HandleTypeDef* hsd = (SD_HandleTypeDef* )(hdma->Parent);
  2589.   HAL_SD_CardStateTypeDef CardState;
  2590.  
  2591.   /* Clear All flags */
  2592.   __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS);
  2593.  
  2594.   CardState = HAL_SD_GetCardState(hsd);
  2595.   hsd->State = HAL_SD_STATE_READY;
  2596.   hsd->Context = SD_CONTEXT_NONE;
  2597.   if((CardState == HAL_SD_CARD_RECEIVING) || (CardState == HAL_SD_CARD_SENDING))
  2598.   {
  2599.     hsd->ErrorCode |= SDMMC_CmdStopTransfer(hsd->Instance);
  2600.   }
  2601.  
  2602.   if(hsd->ErrorCode == HAL_SD_ERROR_NONE)
  2603.   {
  2604. #if (USE_HAL_SD_REGISTER_CALLBACKS == 1)
  2605.     hsd->AbortCpltCallback(hsd);
  2606. #else
  2607.     HAL_SD_AbortCallback(hsd);
  2608. #endif
  2609.   }
  2610.   else
  2611.   {
  2612. #if (USE_HAL_SD_REGISTER_CALLBACKS == 1)
  2613.     hsd->ErrorCallback(hsd);
  2614. #else
  2615.     HAL_SD_ErrorCallback(hsd);
  2616. #endif
  2617.   }
  2618. }
  2619.  
  2620. /**
  2621.   * @brief  Initializes the sd card.
  2622.   * @param  hsd: Pointer to SD handle
  2623.   * @retval SD Card error state
  2624.   */
  2625. static uint32_t SD_InitCard(SD_HandleTypeDef *hsd)
  2626. {
  2627.   HAL_SD_CardCSDTypeDef CSD;
  2628.   uint32_t errorstate;
  2629.   uint16_t sd_rca = 1U;
  2630.  
  2631.   /* Check the power State */
  2632.   if(SDIO_GetPowerState(hsd->Instance) == 0U)
  2633.   {
  2634.     /* Power off */
  2635.     return HAL_SD_ERROR_REQUEST_NOT_APPLICABLE;
  2636.   }
  2637.  
  2638.   if(hsd->SdCard.CardType != CARD_SECURED)
  2639.   {
  2640.     /* Send CMD2 ALL_SEND_CID */
  2641.     errorstate = SDMMC_CmdSendCID(hsd->Instance);
  2642.     if(errorstate != HAL_SD_ERROR_NONE)
  2643.     {
  2644.       return errorstate;
  2645.     }
  2646.     else
  2647.     {
  2648.       /* Get Card identification number data */
  2649.       hsd->CID[0U] = SDIO_GetResponse(hsd->Instance, SDIO_RESP1);
  2650.       hsd->CID[1U] = SDIO_GetResponse(hsd->Instance, SDIO_RESP2);
  2651.       hsd->CID[2U] = SDIO_GetResponse(hsd->Instance, SDIO_RESP3);
  2652.       hsd->CID[3U] = SDIO_GetResponse(hsd->Instance, SDIO_RESP4);
  2653.     }
  2654.   }
  2655.  
  2656.   if(hsd->SdCard.CardType != CARD_SECURED)
  2657.   {
  2658.     /* Send CMD3 SET_REL_ADDR with argument 0 */
  2659.     /* SD Card publishes its RCA. */
  2660.     errorstate = SDMMC_CmdSetRelAdd(hsd->Instance, &sd_rca);
  2661.     if(errorstate != HAL_SD_ERROR_NONE)
  2662.     {
  2663.       return errorstate;
  2664.     }
  2665.   }
  2666.   if(hsd->SdCard.CardType != CARD_SECURED)
  2667.   {
  2668.     /* Get the SD card RCA */
  2669.     hsd->SdCard.RelCardAdd = sd_rca;
  2670.  
  2671.     /* Send CMD9 SEND_CSD with argument as card's RCA */
  2672.     errorstate = SDMMC_CmdSendCSD(hsd->Instance, (uint32_t)(hsd->SdCard.RelCardAdd << 16U));
  2673.     if(errorstate != HAL_SD_ERROR_NONE)
  2674.     {
  2675.       return errorstate;
  2676.     }
  2677.     else
  2678.     {
  2679.       /* Get Card Specific Data */
  2680.       hsd->CSD[0U] = SDIO_GetResponse(hsd->Instance, SDIO_RESP1);
  2681.       hsd->CSD[1U] = SDIO_GetResponse(hsd->Instance, SDIO_RESP2);
  2682.       hsd->CSD[2U] = SDIO_GetResponse(hsd->Instance, SDIO_RESP3);
  2683.       hsd->CSD[3U] = SDIO_GetResponse(hsd->Instance, SDIO_RESP4);
  2684.     }
  2685.   }
  2686.  
  2687.   /* Get the Card Class */
  2688.   hsd->SdCard.Class = (SDIO_GetResponse(hsd->Instance, SDIO_RESP2) >> 20U);
  2689.  
  2690.   /* Get CSD parameters */
  2691.   if (HAL_SD_GetCardCSD(hsd, &CSD) != HAL_OK)
  2692.   {
  2693.     return HAL_SD_ERROR_UNSUPPORTED_FEATURE;
  2694.   }
  2695.  
  2696.   /* Select the Card */
  2697.   errorstate = SDMMC_CmdSelDesel(hsd->Instance, (uint32_t)(((uint32_t)hsd->SdCard.RelCardAdd) << 16U));
  2698.   if(errorstate != HAL_SD_ERROR_NONE)
  2699.   {
  2700.     return errorstate;
  2701.   }
  2702.  
  2703.   /* Configure SDIO peripheral interface */
  2704.   (void)SDIO_Init(hsd->Instance, hsd->Init);
  2705.  
  2706.   /* All cards are initialized */
  2707.   return HAL_SD_ERROR_NONE;
  2708. }
  2709.  
  2710. /**
  2711.   * @brief  Enquires cards about their operating voltage and configures clock
  2712.   *         controls and stores SD information that will be needed in future
  2713.   *         in the SD handle.
  2714.   * @param  hsd: Pointer to SD handle
  2715.   * @retval error state
  2716.   */
  2717. static uint32_t SD_PowerON(SD_HandleTypeDef *hsd)
  2718. {
  2719.   __IO uint32_t count = 0U;
  2720.   uint32_t response = 0U, validvoltage = 0U;
  2721.   uint32_t errorstate;
  2722.  
  2723.   /* CMD0: GO_IDLE_STATE */
  2724.   errorstate = SDMMC_CmdGoIdleState(hsd->Instance);
  2725.   if(errorstate != HAL_SD_ERROR_NONE)
  2726.   {
  2727.     return errorstate;
  2728.   }
  2729.  
  2730.   /* CMD8: SEND_IF_COND: Command available only on V2.0 cards */
  2731.   errorstate = SDMMC_CmdOperCond(hsd->Instance);
  2732.   if(errorstate != HAL_SD_ERROR_NONE)
  2733.   {
  2734.     hsd->SdCard.CardVersion = CARD_V1_X;
  2735.     /* CMD0: GO_IDLE_STATE */
  2736.     errorstate = SDMMC_CmdGoIdleState(hsd->Instance);
  2737.     if(errorstate != HAL_SD_ERROR_NONE)
  2738.     {
  2739.       return errorstate;
  2740.     }
  2741.  
  2742.   }
  2743.   else
  2744.   {
  2745.     hsd->SdCard.CardVersion = CARD_V2_X;
  2746.   }
  2747.  
  2748.   if( hsd->SdCard.CardVersion == CARD_V2_X)
  2749.   {
  2750.     /* SEND CMD55 APP_CMD with RCA as 0 */
  2751.     errorstate = SDMMC_CmdAppCommand(hsd->Instance, 0);
  2752.     if(errorstate != HAL_SD_ERROR_NONE)
  2753.     {
  2754.       return HAL_SD_ERROR_UNSUPPORTED_FEATURE;
  2755.     }
  2756.   }
  2757.   /* SD CARD */
  2758.   /* Send ACMD41 SD_APP_OP_COND with Argument 0x80100000 */
  2759.   while((count < SDMMC_MAX_VOLT_TRIAL) && (validvoltage == 0U))
  2760.   {
  2761.     /* SEND CMD55 APP_CMD with RCA as 0 */
  2762.     errorstate = SDMMC_CmdAppCommand(hsd->Instance, 0);
  2763.     if(errorstate != HAL_SD_ERROR_NONE)
  2764.     {
  2765.       return errorstate;
  2766.     }
  2767.  
  2768.     /* Send CMD41 */
  2769.     errorstate = SDMMC_CmdAppOperCommand(hsd->Instance, SDMMC_VOLTAGE_WINDOW_SD | SDMMC_HIGH_CAPACITY | SD_SWITCH_1_8V_CAPACITY);
  2770.     if(errorstate != HAL_SD_ERROR_NONE)
  2771.     {
  2772.       return HAL_SD_ERROR_UNSUPPORTED_FEATURE;
  2773.     }
  2774.  
  2775.     /* Get command response */
  2776.     response = SDIO_GetResponse(hsd->Instance, SDIO_RESP1);
  2777.  
  2778.     /* Get operating voltage*/
  2779.     validvoltage = (((response >> 31U) == 1U) ? 1U : 0U);
  2780.  
  2781.     count++;
  2782.   }
  2783.  
  2784.   if(count >= SDMMC_MAX_VOLT_TRIAL)
  2785.   {
  2786.     return HAL_SD_ERROR_INVALID_VOLTRANGE;
  2787.   }
  2788.  
  2789.   if((response & SDMMC_HIGH_CAPACITY) == SDMMC_HIGH_CAPACITY) /* (response &= SD_HIGH_CAPACITY) */
  2790.   {
  2791.     hsd->SdCard.CardType = CARD_SDHC_SDXC;
  2792.   }
  2793.   else
  2794.   {
  2795.     hsd->SdCard.CardType = CARD_SDSC;
  2796.   }
  2797.  
  2798.  
  2799.   return HAL_SD_ERROR_NONE;
  2800. }
  2801.  
  2802. /**
  2803.   * @brief  Turns the SDIO output signals off.
  2804.   * @param  hsd: Pointer to SD handle
  2805.   * @retval None
  2806.   */
  2807. static void SD_PowerOFF(SD_HandleTypeDef *hsd)
  2808. {
  2809.   /* Set Power State to OFF */
  2810.   (void)SDIO_PowerState_OFF(hsd->Instance);
  2811. }
  2812.  
  2813. /**
  2814.   * @brief  Send Status info command.
  2815.   * @param  hsd: pointer to SD handle
  2816.   * @param  pSDstatus: Pointer to the buffer that will contain the SD card status
  2817.   *         SD Status register)
  2818.   * @retval error state
  2819.   */
  2820. static uint32_t SD_SendSDStatus(SD_HandleTypeDef *hsd, uint32_t *pSDstatus)
  2821. {
  2822.   SDIO_DataInitTypeDef config;
  2823.   uint32_t errorstate;
  2824.   uint32_t tickstart = HAL_GetTick();
  2825.   uint32_t count;
  2826.   uint32_t *pData = pSDstatus;
  2827.  
  2828.   /* Check SD response */
  2829.   if((SDIO_GetResponse(hsd->Instance, SDIO_RESP1) & SDMMC_CARD_LOCKED) == SDMMC_CARD_LOCKED)
  2830.   {
  2831.     return HAL_SD_ERROR_LOCK_UNLOCK_FAILED;
  2832.   }
  2833.  
  2834.   /* Set block size for card if it is not equal to current block size for card */
  2835.   errorstate = SDMMC_CmdBlockLength(hsd->Instance, 64U);
  2836.   if(errorstate != HAL_SD_ERROR_NONE)
  2837.   {
  2838.     hsd->ErrorCode |= HAL_SD_ERROR_NONE;
  2839.     return errorstate;
  2840.   }
  2841.  
  2842.   /* Send CMD55 */
  2843.   errorstate = SDMMC_CmdAppCommand(hsd->Instance, (uint32_t)(hsd->SdCard.RelCardAdd << 16U));
  2844.   if(errorstate != HAL_SD_ERROR_NONE)
  2845.   {
  2846.     hsd->ErrorCode |= HAL_SD_ERROR_NONE;
  2847.     return errorstate;
  2848.   }
  2849.  
  2850.   /* Configure the SD DPSM (Data Path State Machine) */
  2851.   config.DataTimeOut   = SDMMC_DATATIMEOUT;
  2852.   config.DataLength    = 64U;
  2853.   config.DataBlockSize = SDIO_DATABLOCK_SIZE_64B;
  2854.   config.TransferDir   = SDIO_TRANSFER_DIR_TO_SDIO;
  2855.   config.TransferMode  = SDIO_TRANSFER_MODE_BLOCK;
  2856.   config.DPSM          = SDIO_DPSM_ENABLE;
  2857.   (void)SDIO_ConfigData(hsd->Instance, &config);
  2858.  
  2859.   /* Send ACMD13 (SD_APP_STAUS)  with argument as card's RCA */
  2860.   errorstate = SDMMC_CmdStatusRegister(hsd->Instance);
  2861.   if(errorstate != HAL_SD_ERROR_NONE)
  2862.   {
  2863.     hsd->ErrorCode |= HAL_SD_ERROR_NONE;
  2864.     return errorstate;
  2865.   }
  2866.  
  2867.   /* Get status data */
  2868.   while(!__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXOVERR | SDIO_FLAG_DCRCFAIL | SDIO_FLAG_DTIMEOUT | SDIO_FLAG_DBCKEND))
  2869.   {
  2870.     if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXFIFOHF))
  2871.     {
  2872.       for(count = 0U; count < 8U; count++)
  2873.       {
  2874.         *pData = SDIO_ReadFIFO(hsd->Instance);
  2875.         pData++;
  2876.       }
  2877.     }
  2878.  
  2879.     if((HAL_GetTick() - tickstart) >=  SDMMC_DATATIMEOUT)
  2880.     {
  2881.       return HAL_SD_ERROR_TIMEOUT;
  2882.     }
  2883.   }
  2884.  
  2885.   if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DTIMEOUT))
  2886.   {
  2887.     return HAL_SD_ERROR_DATA_TIMEOUT;
  2888.   }
  2889.   else if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DCRCFAIL))
  2890.   {
  2891.     return HAL_SD_ERROR_DATA_CRC_FAIL;
  2892.   }
  2893.   else if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXOVERR))
  2894.   {
  2895.     return HAL_SD_ERROR_RX_OVERRUN;
  2896.   }
  2897.   else
  2898.   {
  2899.     /* Nothing to do */
  2900.   }
  2901.  
  2902.   while ((__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXDAVL)))
  2903.   {
  2904.     *pData = SDIO_ReadFIFO(hsd->Instance);
  2905.     pData++;
  2906.  
  2907.     if((HAL_GetTick() - tickstart) >=  SDMMC_DATATIMEOUT)
  2908.     {
  2909.       return HAL_SD_ERROR_TIMEOUT;
  2910.     }
  2911.   }
  2912.  
  2913.   /* Clear all the static status flags*/
  2914.   __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS);
  2915.  
  2916.   return HAL_SD_ERROR_NONE;
  2917. }
  2918.  
  2919. /**
  2920.   * @brief  Returns the current card's status.
  2921.   * @param  hsd: Pointer to SD handle
  2922.   * @param  pCardStatus: pointer to the buffer that will contain the SD card
  2923.   *         status (Card Status register)
  2924.   * @retval error state
  2925.   */
  2926. static uint32_t SD_SendStatus(SD_HandleTypeDef *hsd, uint32_t *pCardStatus)
  2927. {
  2928.   uint32_t errorstate;
  2929.  
  2930.   if(pCardStatus == NULL)
  2931.   {
  2932.     return HAL_SD_ERROR_PARAM;
  2933.   }
  2934.  
  2935.   /* Send Status command */
  2936.   errorstate = SDMMC_CmdSendStatus(hsd->Instance, (uint32_t)(hsd->SdCard.RelCardAdd << 16U));
  2937.   if(errorstate != HAL_SD_ERROR_NONE)
  2938.   {
  2939.     return errorstate;
  2940.   }
  2941.  
  2942.   /* Get SD card status */
  2943.   *pCardStatus = SDIO_GetResponse(hsd->Instance, SDIO_RESP1);
  2944.  
  2945.   return HAL_SD_ERROR_NONE;
  2946. }
  2947.  
  2948. /**
  2949.   * @brief  Enables the SDIO wide bus mode.
  2950.   * @param  hsd: pointer to SD handle
  2951.   * @retval error state
  2952.   */
  2953. static uint32_t SD_WideBus_Enable(SD_HandleTypeDef *hsd)
  2954. {
  2955.   uint32_t scr[2U] = {0U, 0U};
  2956.   uint32_t errorstate;
  2957.  
  2958.   if((SDIO_GetResponse(hsd->Instance, SDIO_RESP1) & SDMMC_CARD_LOCKED) == SDMMC_CARD_LOCKED)
  2959.   {
  2960.     return HAL_SD_ERROR_LOCK_UNLOCK_FAILED;
  2961.   }
  2962.  
  2963.   /* Get SCR Register */
  2964.   errorstate = SD_FindSCR(hsd, scr);
  2965.   if(errorstate != HAL_SD_ERROR_NONE)
  2966.   {
  2967.     return errorstate;
  2968.   }
  2969.  
  2970.   /* If requested card supports wide bus operation */
  2971.   if((scr[1U] & SDMMC_WIDE_BUS_SUPPORT) != SDMMC_ALLZERO)
  2972.   {
  2973.     /* Send CMD55 APP_CMD with argument as card's RCA.*/
  2974.     errorstate = SDMMC_CmdAppCommand(hsd->Instance, (uint32_t)(hsd->SdCard.RelCardAdd << 16U));
  2975.     if(errorstate != HAL_SD_ERROR_NONE)
  2976.     {
  2977.       return errorstate;
  2978.     }
  2979.  
  2980.     /* Send ACMD6 APP_CMD with argument as 2 for wide bus mode */
  2981.     errorstate = SDMMC_CmdBusWidth(hsd->Instance, 2U);
  2982.     if(errorstate != HAL_SD_ERROR_NONE)
  2983.     {
  2984.       return errorstate;
  2985.     }
  2986.  
  2987.     return HAL_SD_ERROR_NONE;
  2988.   }
  2989.   else
  2990.   {
  2991.     return HAL_SD_ERROR_REQUEST_NOT_APPLICABLE;
  2992.   }
  2993. }
  2994.  
  2995. /**
  2996.   * @brief  Disables the SDIO wide bus mode.
  2997.   * @param  hsd: Pointer to SD handle
  2998.   * @retval error state
  2999.   */
  3000. static uint32_t SD_WideBus_Disable(SD_HandleTypeDef *hsd)
  3001. {
  3002.   uint32_t scr[2U] = {0U, 0U};
  3003.   uint32_t errorstate;
  3004.  
  3005.   if((SDIO_GetResponse(hsd->Instance, SDIO_RESP1) & SDMMC_CARD_LOCKED) == SDMMC_CARD_LOCKED)
  3006.   {
  3007.     return HAL_SD_ERROR_LOCK_UNLOCK_FAILED;
  3008.   }
  3009.  
  3010.   /* Get SCR Register */
  3011.   errorstate = SD_FindSCR(hsd, scr);
  3012.   if(errorstate != HAL_SD_ERROR_NONE)
  3013.   {
  3014.     return errorstate;
  3015.   }
  3016.  
  3017.   /* If requested card supports 1 bit mode operation */
  3018.   if((scr[1U] & SDMMC_SINGLE_BUS_SUPPORT) != SDMMC_ALLZERO)
  3019.   {
  3020.     /* Send CMD55 APP_CMD with argument as card's RCA */
  3021.     errorstate = SDMMC_CmdAppCommand(hsd->Instance, (uint32_t)(hsd->SdCard.RelCardAdd << 16U));
  3022.     if(errorstate != HAL_SD_ERROR_NONE)
  3023.     {
  3024.       return errorstate;
  3025.     }
  3026.  
  3027.     /* Send ACMD6 APP_CMD with argument as 0 for single bus mode */
  3028.     errorstate = SDMMC_CmdBusWidth(hsd->Instance, 0U);
  3029.     if(errorstate != HAL_SD_ERROR_NONE)
  3030.     {
  3031.       return errorstate;
  3032.     }
  3033.  
  3034.     return HAL_SD_ERROR_NONE;
  3035.   }
  3036.   else
  3037.   {
  3038.     return HAL_SD_ERROR_REQUEST_NOT_APPLICABLE;
  3039.   }
  3040. }
  3041.  
  3042.  
  3043. /**
  3044.   * @brief  Finds the SD card SCR register value.
  3045.   * @param  hsd: Pointer to SD handle
  3046.   * @param  pSCR: pointer to the buffer that will contain the SCR value
  3047.   * @retval error state
  3048.   */
  3049. static uint32_t SD_FindSCR(SD_HandleTypeDef *hsd, uint32_t *pSCR)
  3050. {
  3051.   SDIO_DataInitTypeDef config;
  3052.   uint32_t errorstate;
  3053.   uint32_t tickstart = HAL_GetTick();
  3054.   uint32_t index = 0U;
  3055.   uint32_t tempscr[2U] = {0U, 0U};
  3056.   uint32_t *scr = pSCR;
  3057.  
  3058.   /* Set Block Size To 8 Bytes */
  3059.   errorstate = SDMMC_CmdBlockLength(hsd->Instance, 8U);
  3060.   if(errorstate != HAL_SD_ERROR_NONE)
  3061.   {
  3062.     return errorstate;
  3063.   }
  3064.  
  3065.   /* Send CMD55 APP_CMD with argument as card's RCA */
  3066.   errorstate = SDMMC_CmdAppCommand(hsd->Instance, (uint32_t)((hsd->SdCard.RelCardAdd) << 16U));
  3067.   if(errorstate != HAL_SD_ERROR_NONE)
  3068.   {
  3069.     return errorstate;
  3070.   }
  3071.  
  3072.   config.DataTimeOut   = SDMMC_DATATIMEOUT;
  3073.   config.DataLength    = 8U;
  3074.   config.DataBlockSize = SDIO_DATABLOCK_SIZE_8B;
  3075.   config.TransferDir   = SDIO_TRANSFER_DIR_TO_SDIO;
  3076.   config.TransferMode  = SDIO_TRANSFER_MODE_BLOCK;
  3077.   config.DPSM          = SDIO_DPSM_ENABLE;
  3078.   (void)SDIO_ConfigData(hsd->Instance, &config);
  3079.  
  3080.   /* Send ACMD51 SD_APP_SEND_SCR with argument as 0 */
  3081.   errorstate = SDMMC_CmdSendSCR(hsd->Instance);
  3082.   if(errorstate != HAL_SD_ERROR_NONE)
  3083.   {
  3084.     return errorstate;
  3085.   }
  3086.  
  3087.   while(!__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXOVERR | SDIO_FLAG_DCRCFAIL | SDIO_FLAG_DTIMEOUT))
  3088.   {
  3089.     if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXDAVL))
  3090.     {
  3091.       *(tempscr + index) = SDIO_ReadFIFO(hsd->Instance);
  3092.       index++;
  3093.     }
  3094.     else if(!__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXACT))
  3095.     {
  3096.       break;
  3097.     }
  3098.  
  3099.     if((HAL_GetTick() - tickstart) >=  SDMMC_DATATIMEOUT)
  3100.     {
  3101.       return HAL_SD_ERROR_TIMEOUT;
  3102.     }
  3103.   }
  3104.  
  3105.   if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DTIMEOUT))
  3106.   {
  3107.     __HAL_SD_CLEAR_FLAG(hsd, SDIO_FLAG_DTIMEOUT);
  3108.  
  3109.     return HAL_SD_ERROR_DATA_TIMEOUT;
  3110.   }
  3111.   else if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_DCRCFAIL))
  3112.   {
  3113.     __HAL_SD_CLEAR_FLAG(hsd, SDIO_FLAG_DCRCFAIL);
  3114.  
  3115.     return HAL_SD_ERROR_DATA_CRC_FAIL;
  3116.   }
  3117.   else if(__HAL_SD_GET_FLAG(hsd, SDIO_FLAG_RXOVERR))
  3118.   {
  3119.     __HAL_SD_CLEAR_FLAG(hsd, SDIO_FLAG_RXOVERR);
  3120.  
  3121.     return HAL_SD_ERROR_RX_OVERRUN;
  3122.   }
  3123.   else
  3124.   {
  3125.     /* No error flag set */
  3126.     /* Clear all the static flags */
  3127.     __HAL_SD_CLEAR_FLAG(hsd, SDIO_STATIC_DATA_FLAGS);
  3128.  
  3129.     *scr = (((tempscr[1] & SDMMC_0TO7BITS) << 24)  | ((tempscr[1] & SDMMC_8TO15BITS) << 8) |\
  3130.             ((tempscr[1] & SDMMC_16TO23BITS) >> 8) | ((tempscr[1] & SDMMC_24TO31BITS) >> 24));
  3131.     scr++;
  3132.     *scr = (((tempscr[0] & SDMMC_0TO7BITS) << 24)  | ((tempscr[0] & SDMMC_8TO15BITS) << 8) |\
  3133.             ((tempscr[0] & SDMMC_16TO23BITS) >> 8) | ((tempscr[0] & SDMMC_24TO31BITS) >> 24));
  3134.  
  3135.   }
  3136.  
  3137.   return HAL_SD_ERROR_NONE;
  3138. }
  3139.  
  3140. /**
  3141.   * @brief  Wrap up reading in non-blocking mode.
  3142.   * @param  hsd: pointer to a SD_HandleTypeDef structure that contains
  3143.   *              the configuration information.
  3144.   * @retval None
  3145.   */
  3146. static void SD_Read_IT(SD_HandleTypeDef *hsd)
  3147. {
  3148.   uint32_t count, data, dataremaining;
  3149.   uint8_t* tmp;
  3150.  
  3151.   tmp = hsd->pRxBuffPtr;
  3152.   dataremaining = hsd->RxXferSize;
  3153.  
  3154.   if (dataremaining > 0U)
  3155.   {
  3156.     /* Read data from SDIO Rx FIFO */
  3157.     for(count = 0U; count < 8U; count++)
  3158.     {
  3159.       data = SDIO_ReadFIFO(hsd->Instance);
  3160.       *tmp = (uint8_t)(data & 0xFFU);
  3161.       tmp++;
  3162.       dataremaining--;
  3163.       *tmp = (uint8_t)((data >> 8U) & 0xFFU);
  3164.       tmp++;
  3165.       dataremaining--;
  3166.       *tmp = (uint8_t)((data >> 16U) & 0xFFU);
  3167.       tmp++;
  3168.       dataremaining--;
  3169.       *tmp = (uint8_t)((data >> 24U) & 0xFFU);
  3170.       tmp++;
  3171.       dataremaining--;
  3172.     }
  3173.  
  3174.     hsd->pRxBuffPtr = tmp;
  3175.     hsd->RxXferSize = dataremaining;
  3176.   }
  3177. }
  3178.  
  3179. /**
  3180.   * @brief  Wrap up writing in non-blocking mode.
  3181.   * @param  hsd: pointer to a SD_HandleTypeDef structure that contains
  3182.   *              the configuration information.
  3183.   * @retval None
  3184.   */
  3185. static void SD_Write_IT(SD_HandleTypeDef *hsd)
  3186. {
  3187.   uint32_t count, data, dataremaining;
  3188.   uint8_t* tmp;
  3189.  
  3190.   tmp = hsd->pTxBuffPtr;
  3191.   dataremaining = hsd->TxXferSize;
  3192.  
  3193.   if (dataremaining > 0U)
  3194.   {
  3195.     /* Write data to SDIO Tx FIFO */
  3196.     for(count = 0U; count < 8U; count++)
  3197.     {
  3198.       data = (uint32_t)(*tmp);
  3199.       tmp++;
  3200.       dataremaining--;
  3201.       data |= ((uint32_t)(*tmp) << 8U);
  3202.       tmp++;
  3203.       dataremaining--;
  3204.       data |= ((uint32_t)(*tmp) << 16U);
  3205.       tmp++;
  3206.       dataremaining--;
  3207.       data |= ((uint32_t)(*tmp) << 24U);
  3208.       tmp++;
  3209.       dataremaining--;
  3210.       (void)SDIO_WriteFIFO(hsd->Instance, &data);
  3211.     }
  3212.  
  3213.     hsd->pTxBuffPtr = tmp;
  3214.     hsd->TxXferSize = dataremaining;
  3215.   }
  3216. }
  3217.  
  3218. /**
  3219.   * @}
  3220.   */
  3221.  
  3222. #endif /* HAL_SD_MODULE_ENABLED */
  3223.  
  3224. /**
  3225.   * @}
  3226.   */
  3227.  
  3228. /**
  3229.   * @}
  3230.   */
  3231.  
  3232. #endif /* SDIO */
  3233.