/**
******************************************************************************
* @file stm32l1xx_hal_nor.c
* @author MCD Application Team
* @brief NOR HAL module driver.
* This file provides a generic firmware to drive NOR memories mounted
* as external device.
*
******************************************************************************
* @attention
*
* Copyright (c) 2016 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
@verbatim
==============================================================================
##### How to use this driver #####
==============================================================================
[..]
This driver is a generic layered driver which contains a set of APIs used to
control NOR flash memories. It uses the FSMC layer functions to interface
with NOR devices. This driver is used as follows:
(+) NOR flash memory configuration sequence using the function HAL_NOR_Init()
with control and timing parameters for both normal and extended mode.
(+) Read NOR flash memory manufacturer code and device IDs using the function
HAL_NOR_Read_ID(). The read information is stored in the NOR_ID_TypeDef
structure declared by the function caller.
(+) Access NOR flash memory by read/write data unit operations using the functions
HAL_NOR_Read(), HAL_NOR_Program().
(+) Perform NOR flash erase block/chip operations using the functions
HAL_NOR_Erase_Block() and HAL_NOR_Erase_Chip().
(+) Read the NOR flash CFI (common flash interface) IDs using the function
HAL_NOR_Read_CFI(). The read information is stored in the NOR_CFI_TypeDef
structure declared by the function caller.
(+) You can also control the NOR device by calling the control APIs HAL_NOR_WriteOperation_Enable()/
HAL_NOR_WriteOperation_Disable() to respectively enable/disable the NOR write operation
(+) You can monitor the NOR device HAL state by calling the function
HAL_NOR_GetState()
[..]
(@) This driver is a set of generic APIs which handle standard NOR flash operations.
If a NOR flash device contains different operations and/or implementations,
it should be implemented separately.
*** NOR HAL driver macros list ***
=============================================
[..]
Below the list of most used macros in NOR HAL driver.
(+) NOR_WRITE : NOR memory write data to specified address
*** Callback registration ***
=============================================
[..]
The compilation define USE_HAL_NOR_REGISTER_CALLBACKS when set to 1
allows the user to configure dynamically the driver callbacks.
Use Functions HAL_NOR_RegisterCallback() to register a user callback,
it allows to register following callbacks:
(+) MspInitCallback : NOR MspInit.
(+) MspDeInitCallback : NOR MspDeInit.
This function takes as parameters the HAL peripheral handle, the Callback ID
and a pointer to the user callback function.
Use function HAL_NOR_UnRegisterCallback() to reset a callback to the default
weak (surcharged) function. It allows to reset following callbacks:
(+) MspInitCallback : NOR MspInit.
(+) MspDeInitCallback : NOR MspDeInit.
This function) takes as parameters the HAL peripheral handle and the Callback ID.
By default, after the HAL_NOR_Init and if the state is HAL_NOR_STATE_RESET
all callbacks are reset to the corresponding legacy weak (surcharged) functions.
Exception done for MspInit and MspDeInit callbacks that are respectively
reset to the legacy weak (surcharged) functions in the HAL_NOR_Init
and HAL_NOR_DeInit only when these callbacks are null (not registered beforehand).
If not, MspInit or MspDeInit are not null, the HAL_NOR_Init and HAL_NOR_DeInit
keep and use the user MspInit/MspDeInit callbacks (registered beforehand)
Callbacks can be registered/unregistered in READY state only.
Exception done for MspInit/MspDeInit callbacks that can be registered/unregistered
in READY or RESET state, thus registered (user) MspInit/DeInit callbacks can be used
during the Init/DeInit.
In that case first register the MspInit/MspDeInit user callbacks
using HAL_NOR_RegisterCallback before calling HAL_NOR_DeInit
or HAL_NOR_Init function.
When The compilation define USE_HAL_NOR_REGISTER_CALLBACKS is set to 0 or
not defined, the callback registering feature is not available
and weak (surcharged) callbacks are used.
@endverbatim
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32l1xx_hal.h"
#if defined(FSMC_BANK1)
/** @addtogroup STM32L1xx_HAL_Driver
* @{
*/
#ifdef HAL_NOR_MODULE_ENABLED
/** @defgroup NOR NOR
* @brief NOR driver modules
* @{
*/
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/** @defgroup NOR_Private_Defines NOR Private Defines
* @{
*/
/* Constants to define address to set to write a command */
#define NOR_CMD_ADDRESS_FIRST (uint16_t)0x0555
#define NOR_CMD_ADDRESS_FIRST_CFI (uint16_t)0x0055
#define NOR_CMD_ADDRESS_SECOND (uint16_t)0x02AA
#define NOR_CMD_ADDRESS_THIRD (uint16_t)0x0555
#define NOR_CMD_ADDRESS_FOURTH (uint16_t)0x0555
#define NOR_CMD_ADDRESS_FIFTH (uint16_t)0x02AA
#define NOR_CMD_ADDRESS_SIXTH (uint16_t)0x0555
/* Constants to define data to program a command */
#define NOR_CMD_DATA_READ_RESET (uint16_t)0x00F0
#define NOR_CMD_DATA_FIRST (uint16_t)0x00AA
#define NOR_CMD_DATA_SECOND (uint16_t)0x0055
#define NOR_CMD_DATA_AUTO_SELECT (uint16_t)0x0090
#define NOR_CMD_DATA_PROGRAM (uint16_t)0x00A0
#define NOR_CMD_DATA_CHIP_BLOCK_ERASE_THIRD (uint16_t)0x0080
#define NOR_CMD_DATA_CHIP_BLOCK_ERASE_FOURTH (uint16_t)0x00AA
#define NOR_CMD_DATA_CHIP_BLOCK_ERASE_FIFTH (uint16_t)0x0055
#define NOR_CMD_DATA_CHIP_ERASE (uint16_t)0x0010
#define NOR_CMD_DATA_CFI (uint16_t)0x0098
#define NOR_CMD_DATA_BUFFER_AND_PROG (uint8_t)0x25
#define NOR_CMD_DATA_BUFFER_AND_PROG_CONFIRM (uint8_t)0x29
#define NOR_CMD_DATA_BLOCK_ERASE (uint8_t)0x30
#define NOR_CMD_READ_ARRAY (uint16_t)0x00FF
#define NOR_CMD_WORD_PROGRAM (uint16_t)0x0040
#define NOR_CMD_BUFFERED_PROGRAM (uint16_t)0x00E8
#define NOR_CMD_CONFIRM (uint16_t)0x00D0
#define NOR_CMD_BLOCK_ERASE (uint16_t)0x0020
#define NOR_CMD_BLOCK_UNLOCK (uint16_t)0x0060
#define NOR_CMD_READ_STATUS_REG (uint16_t)0x0070
#define NOR_CMD_CLEAR_STATUS_REG (uint16_t)0x0050
/* Mask on NOR STATUS REGISTER */
#define NOR_MASK_STATUS_DQ4 (uint16_t)0x0010
#define NOR_MASK_STATUS_DQ5 (uint16_t)0x0020
#define NOR_MASK_STATUS_DQ6 (uint16_t)0x0040
#define NOR_MASK_STATUS_DQ7 (uint16_t)0x0080
/* Address of the primary command set */
#define NOR_ADDRESS_COMMAND_SET (uint16_t)0x0013
/* Command set code assignment (defined in JEDEC JEP137B version may 2004) */
#define NOR_INTEL_SHARP_EXT_COMMAND_SET (uint16_t)0x0001 /* Supported in this driver */
#define NOR_AMD_FUJITSU_COMMAND_SET (uint16_t)0x0002 /* Supported in this driver */
#define NOR_INTEL_STANDARD_COMMAND_SET (uint16_t)0x0003 /* Not Supported in this driver */
#define NOR_AMD_FUJITSU_EXT_COMMAND_SET (uint16_t)0x0004 /* Not Supported in this driver */
#define NOR_WINDBOND_STANDARD_COMMAND_SET (uint16_t)0x0006 /* Not Supported in this driver */
#define NOR_MITSUBISHI_STANDARD_COMMAND_SET (uint16_t)0x0100 /* Not Supported in this driver */
#define NOR_MITSUBISHI_EXT_COMMAND_SET (uint16_t)0x0101 /* Not Supported in this driver */
#define NOR_PAGE_WRITE_COMMAND_SET (uint16_t)0x0102 /* Not Supported in this driver */
#define NOR_INTEL_PERFORMANCE_COMMAND_SET (uint16_t)0x0200 /* Not Supported in this driver */
#define NOR_INTEL_DATA_COMMAND_SET (uint16_t)0x0210 /* Not Supported in this driver */
/**
* @}
*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/** @defgroup NOR_Private_Variables NOR Private Variables
* @{
*/
static uint32_t uwNORMemoryDataWidth = NOR_MEMORY_8B;
/**
* @}
*/
/* Private functions ---------------------------------------------------------*/
/* Exported functions --------------------------------------------------------*/
/** @defgroup NOR_Exported_Functions NOR Exported Functions
* @{
*/
/** @defgroup NOR_Exported_Functions_Group1 Initialization and de-initialization functions
* @brief Initialization and Configuration functions
*
@verbatim
==============================================================================
##### NOR Initialization and de_initialization functions #####
==============================================================================
[..]
This section provides functions allowing to initialize/de-initialize
the NOR memory
@endverbatim
* @{
*/
/**
* @brief Perform the NOR memory Initialization sequence
* @param hnor pointer to a NOR_HandleTypeDef structure that contains
* the configuration information for NOR module.
* @param Timing pointer to NOR control timing structure
* @param ExtTiming pointer to NOR extended mode timing structure
* @retval HAL status
*/
HAL_StatusTypeDef HAL_NOR_Init(NOR_HandleTypeDef *hnor, FSMC_NORSRAM_TimingTypeDef *Timing,
FSMC_NORSRAM_TimingTypeDef *ExtTiming)
{
uint32_t deviceaddress;
HAL_StatusTypeDef status = HAL_OK;
/* Check the NOR handle parameter */
if (hnor == NULL)
{
return HAL_ERROR;
}
if (hnor->State == HAL_NOR_STATE_RESET)
{
/* Allocate lock resource and initialize it */
hnor->Lock = HAL_UNLOCKED;
#if (USE_HAL_NOR_REGISTER_CALLBACKS == 1)
if (hnor->MspInitCallback == NULL)
{
hnor->MspInitCallback = HAL_NOR_MspInit;
}
/* Init the low level hardware */
hnor->MspInitCallback(hnor);
#else
/* Initialize the low level hardware (MSP) */
HAL_NOR_MspInit(hnor);
#endif /* (USE_HAL_NOR_REGISTER_CALLBACKS) */
}
/* Initialize NOR control Interface */
(void)FSMC_NORSRAM_Init(hnor->Instance, &(hnor->Init));
/* Initialize NOR timing Interface */
(void)FSMC_NORSRAM_Timing_Init(hnor->Instance, Timing, hnor->Init.NSBank);
/* Initialize NOR extended mode timing Interface */
(void)FSMC_NORSRAM_Extended_Timing_Init(hnor->Extended, ExtTiming, hnor->Init.NSBank, hnor->Init.ExtendedMode);
/* Enable the NORSRAM device */
__FSMC_NORSRAM_ENABLE(hnor->Instance, hnor->Init.NSBank);
/* Initialize NOR Memory Data Width*/
if (hnor->Init.MemoryDataWidth == FSMC_NORSRAM_MEM_BUS_WIDTH_8)
{
uwNORMemoryDataWidth = NOR_MEMORY_8B;
}
else
{
uwNORMemoryDataWidth = NOR_MEMORY_16B;
}
/* Initialize the NOR controller state */
hnor->State = HAL_NOR_STATE_READY;
/* Select the NOR device address */
if (hnor->Init.NSBank == FSMC_NORSRAM_BANK1)
{
deviceaddress = NOR_MEMORY_ADRESS1;
}
else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK2)
{
deviceaddress = NOR_MEMORY_ADRESS2;
}
else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK3)
{
deviceaddress = NOR_MEMORY_ADRESS3;
}
else /* FSMC_NORSRAM_BANK4 */
{
deviceaddress = NOR_MEMORY_ADRESS4;
}
if (hnor->Init.WriteOperation == FSMC_WRITE_OPERATION_DISABLE)
{
(void)FSMC_NORSRAM_WriteOperation_Disable(hnor->Instance, hnor->Init.NSBank);
/* Update the NOR controller state */
hnor->State = HAL_NOR_STATE_PROTECTED;
}
else
{
/* Get the value of the command set */
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_FIRST_CFI), NOR_CMD_DATA_CFI);
hnor->CommandSet = *(__IO uint16_t *) NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_ADDRESS_COMMAND_SET);
status = HAL_NOR_ReturnToReadMode(hnor);
}
return status;
}
/**
* @brief Perform NOR memory De-Initialization sequence
* @param hnor pointer to a NOR_HandleTypeDef structure that contains
* the configuration information for NOR module.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_NOR_DeInit(NOR_HandleTypeDef *hnor)
{
#if (USE_HAL_NOR_REGISTER_CALLBACKS == 1)
if (hnor->MspDeInitCallback == NULL)
{
hnor->MspDeInitCallback = HAL_NOR_MspDeInit;
}
/* DeInit the low level hardware */
hnor->MspDeInitCallback(hnor);
#else
/* De-Initialize the low level hardware (MSP) */
HAL_NOR_MspDeInit(hnor);
#endif /* (USE_HAL_NOR_REGISTER_CALLBACKS) */
/* Configure the NOR registers with their reset values */
(void)FSMC_NORSRAM_DeInit(hnor->Instance, hnor->Extended, hnor->Init.NSBank);
/* Reset the NOR controller state */
hnor->State = HAL_NOR_STATE_RESET;
/* Release Lock */
__HAL_UNLOCK(hnor);
return HAL_OK;
}
/**
* @brief NOR MSP Init
* @param hnor pointer to a NOR_HandleTypeDef structure that contains
* the configuration information for NOR module.
* @retval None
*/
__weak void HAL_NOR_MspInit(NOR_HandleTypeDef *hnor)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hnor);
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_NOR_MspInit could be implemented in the user file
*/
}
/**
* @brief NOR MSP DeInit
* @param hnor pointer to a NOR_HandleTypeDef structure that contains
* the configuration information for NOR module.
* @retval None
*/
__weak void HAL_NOR_MspDeInit(NOR_HandleTypeDef *hnor)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hnor);
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_NOR_MspDeInit could be implemented in the user file
*/
}
/**
* @brief NOR MSP Wait for Ready/Busy signal
* @param hnor pointer to a NOR_HandleTypeDef structure that contains
* the configuration information for NOR module.
* @param Timeout Maximum timeout value
* @retval None
*/
__weak void HAL_NOR_MspWait(NOR_HandleTypeDef *hnor, uint32_t Timeout)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hnor);
UNUSED(Timeout);
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_NOR_MspWait could be implemented in the user file
*/
}
/**
* @}
*/
/** @defgroup NOR_Exported_Functions_Group2 Input and Output functions
* @brief Input Output and memory control functions
*
@verbatim
==============================================================================
##### NOR Input and Output functions #####
==============================================================================
[..]
This section provides functions allowing to use and control the NOR memory
@endverbatim
* @{
*/
/**
* @brief Read NOR flash IDs
* @param hnor pointer to a NOR_HandleTypeDef structure that contains
* the configuration information for NOR module.
* @param pNOR_ID pointer to NOR ID structure
* @retval HAL status
*/
HAL_StatusTypeDef HAL_NOR_Read_ID(NOR_HandleTypeDef *hnor, NOR_IDTypeDef *pNOR_ID)
{
uint32_t deviceaddress;
HAL_NOR_StateTypeDef state;
HAL_StatusTypeDef status = HAL_OK;
/* Check the NOR controller state */
state = hnor->State;
if (state == HAL_NOR_STATE_BUSY)
{
return HAL_BUSY;
}
else if (state == HAL_NOR_STATE_PROTECTED)
{
return HAL_ERROR;
}
else if (state == HAL_NOR_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hnor);
/* Update the NOR controller state */
hnor->State = HAL_NOR_STATE_BUSY;
/* Select the NOR device address */
if (hnor->Init.NSBank == FSMC_NORSRAM_BANK1)
{
deviceaddress = NOR_MEMORY_ADRESS1;
}
else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK2)
{
deviceaddress = NOR_MEMORY_ADRESS2;
}
else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK3)
{
deviceaddress = NOR_MEMORY_ADRESS3;
}
else /* FSMC_NORSRAM_BANK4 */
{
deviceaddress = NOR_MEMORY_ADRESS4;
}
/* Send read ID command */
if (hnor->CommandSet == NOR_AMD_FUJITSU_COMMAND_SET)
{
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_FIRST), NOR_CMD_DATA_FIRST);
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_SECOND), NOR_CMD_DATA_SECOND);
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_THIRD), NOR_CMD_DATA_AUTO_SELECT);
}
else if (hnor->CommandSet == NOR_INTEL_SHARP_EXT_COMMAND_SET)
{
NOR_WRITE(deviceaddress, NOR_CMD_DATA_AUTO_SELECT);
}
else
{
/* Primary command set not supported by the driver */
status = HAL_ERROR;
}
if (status != HAL_ERROR)
{
/* Read the NOR IDs */
pNOR_ID->Manufacturer_Code = *(__IO uint16_t *) NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, MC_ADDRESS);
pNOR_ID->Device_Code1 = *(__IO uint16_t *) NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth,
DEVICE_CODE1_ADDR);
pNOR_ID->Device_Code2 = *(__IO uint16_t *) NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth,
DEVICE_CODE2_ADDR);
pNOR_ID->Device_Code3 = *(__IO uint16_t *) NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth,
DEVICE_CODE3_ADDR);
}
/* Check the NOR controller state */
hnor->State = state;
/* Process unlocked */
__HAL_UNLOCK(hnor);
}
else
{
return HAL_ERROR;
}
return status;
}
/**
* @brief Returns the NOR memory to Read mode.
* @param hnor pointer to a NOR_HandleTypeDef structure that contains
* the configuration information for NOR module.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_NOR_ReturnToReadMode(NOR_HandleTypeDef *hnor)
{
uint32_t deviceaddress;
HAL_NOR_StateTypeDef state;
HAL_StatusTypeDef status = HAL_OK;
/* Check the NOR controller state */
state = hnor->State;
if (state == HAL_NOR_STATE_BUSY)
{
return HAL_BUSY;
}
else if (state == HAL_NOR_STATE_PROTECTED)
{
return HAL_ERROR;
}
else if (state == HAL_NOR_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hnor);
/* Update the NOR controller state */
hnor->State = HAL_NOR_STATE_BUSY;
/* Select the NOR device address */
if (hnor->Init.NSBank == FSMC_NORSRAM_BANK1)
{
deviceaddress = NOR_MEMORY_ADRESS1;
}
else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK2)
{
deviceaddress = NOR_MEMORY_ADRESS2;
}
else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK3)
{
deviceaddress = NOR_MEMORY_ADRESS3;
}
else /* FSMC_NORSRAM_BANK4 */
{
deviceaddress = NOR_MEMORY_ADRESS4;
}
if (hnor->CommandSet == NOR_AMD_FUJITSU_COMMAND_SET)
{
NOR_WRITE(deviceaddress, NOR_CMD_DATA_READ_RESET);
}
else if (hnor->CommandSet == NOR_INTEL_SHARP_EXT_COMMAND_SET)
{
NOR_WRITE(deviceaddress, NOR_CMD_READ_ARRAY);
}
else
{
/* Primary command set not supported by the driver */
status = HAL_ERROR;
}
/* Check the NOR controller state */
hnor->State = state;
/* Process unlocked */
__HAL_UNLOCK(hnor);
}
else
{
return HAL_ERROR;
}
return status;
}
/**
* @brief Read data from NOR memory
* @param hnor pointer to a NOR_HandleTypeDef structure that contains
* the configuration information for NOR module.
* @param pAddress pointer to Device address
* @param pData pointer to read data
* @retval HAL status
*/
HAL_StatusTypeDef HAL_NOR_Read(NOR_HandleTypeDef *hnor, uint32_t *pAddress, uint16_t *pData)
{
uint32_t deviceaddress;
HAL_NOR_StateTypeDef state;
HAL_StatusTypeDef status = HAL_OK;
/* Check the NOR controller state */
state = hnor->State;
if (state == HAL_NOR_STATE_BUSY)
{
return HAL_BUSY;
}
else if (state == HAL_NOR_STATE_PROTECTED)
{
return HAL_ERROR;
}
else if (state == HAL_NOR_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hnor);
/* Update the NOR controller state */
hnor->State = HAL_NOR_STATE_BUSY;
/* Select the NOR device address */
if (hnor->Init.NSBank == FSMC_NORSRAM_BANK1)
{
deviceaddress = NOR_MEMORY_ADRESS1;
}
else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK2)
{
deviceaddress = NOR_MEMORY_ADRESS2;
}
else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK3)
{
deviceaddress = NOR_MEMORY_ADRESS3;
}
else /* FSMC_NORSRAM_BANK4 */
{
deviceaddress = NOR_MEMORY_ADRESS4;
}
/* Send read data command */
if (hnor->CommandSet == NOR_AMD_FUJITSU_COMMAND_SET)
{
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_FIRST), NOR_CMD_DATA_FIRST);
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_SECOND), NOR_CMD_DATA_SECOND);
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_THIRD), NOR_CMD_DATA_READ_RESET);
}
else if (hnor->CommandSet == NOR_INTEL_SHARP_EXT_COMMAND_SET)
{
NOR_WRITE(pAddress, NOR_CMD_READ_ARRAY);
}
else
{
/* Primary command set not supported by the driver */
status = HAL_ERROR;
}
if (status != HAL_ERROR)
{
/* Read the data */
*pData = (uint16_t)(*(__IO uint32_t *)pAddress);
}
/* Check the NOR controller state */
hnor->State = state;
/* Process unlocked */
__HAL_UNLOCK(hnor);
}
else
{
return HAL_ERROR;
}
return status;
}
/**
* @brief Program data to NOR memory
* @param hnor pointer to a NOR_HandleTypeDef structure that contains
* the configuration information for NOR module.
* @param pAddress Device address
* @param pData pointer to the data to write
* @retval HAL status
*/
HAL_StatusTypeDef HAL_NOR_Program(NOR_HandleTypeDef *hnor, uint32_t *pAddress, uint16_t *pData)
{
uint32_t deviceaddress;
HAL_StatusTypeDef status = HAL_OK;
/* Check the NOR controller state */
if (hnor->State == HAL_NOR_STATE_BUSY)
{
return HAL_BUSY;
}
else if (hnor->State == HAL_NOR_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hnor);
/* Update the NOR controller state */
hnor->State = HAL_NOR_STATE_BUSY;
/* Select the NOR device address */
if (hnor->Init.NSBank == FSMC_NORSRAM_BANK1)
{
deviceaddress = NOR_MEMORY_ADRESS1;
}
else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK2)
{
deviceaddress = NOR_MEMORY_ADRESS2;
}
else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK3)
{
deviceaddress = NOR_MEMORY_ADRESS3;
}
else /* FSMC_NORSRAM_BANK4 */
{
deviceaddress = NOR_MEMORY_ADRESS4;
}
/* Send program data command */
if (hnor->CommandSet == NOR_AMD_FUJITSU_COMMAND_SET)
{
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_FIRST), NOR_CMD_DATA_FIRST);
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_SECOND), NOR_CMD_DATA_SECOND);
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_THIRD), NOR_CMD_DATA_PROGRAM);
}
else if (hnor->CommandSet == NOR_INTEL_SHARP_EXT_COMMAND_SET)
{
NOR_WRITE(pAddress, NOR_CMD_WORD_PROGRAM);
}
else
{
/* Primary command set not supported by the driver */
status = HAL_ERROR;
}
if (status != HAL_ERROR)
{
/* Write the data */
NOR_WRITE(pAddress, *pData);
}
/* Check the NOR controller state */
hnor->State = HAL_NOR_STATE_READY;
/* Process unlocked */
__HAL_UNLOCK(hnor);
}
else
{
return HAL_ERROR;
}
return status;
}
/**
* @brief Reads a half-word buffer from the NOR memory.
* @param hnor pointer to the NOR handle
* @param uwAddress NOR memory internal address to read from.
* @param pData pointer to the buffer that receives the data read from the
* NOR memory.
* @param uwBufferSize number of Half word to read.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_NOR_ReadBuffer(NOR_HandleTypeDef *hnor, uint32_t uwAddress, uint16_t *pData,
uint32_t uwBufferSize)
{
uint32_t deviceaddress;
uint32_t size = uwBufferSize;
uint32_t address = uwAddress;
uint16_t *data = pData;
HAL_NOR_StateTypeDef state;
HAL_StatusTypeDef status = HAL_OK;
/* Check the NOR controller state */
state = hnor->State;
if (state == HAL_NOR_STATE_BUSY)
{
return HAL_BUSY;
}
else if (state == HAL_NOR_STATE_PROTECTED)
{
return HAL_ERROR;
}
else if (state == HAL_NOR_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hnor);
/* Update the NOR controller state */
hnor->State = HAL_NOR_STATE_BUSY;
/* Select the NOR device address */
if (hnor->Init.NSBank == FSMC_NORSRAM_BANK1)
{
deviceaddress = NOR_MEMORY_ADRESS1;
}
else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK2)
{
deviceaddress = NOR_MEMORY_ADRESS2;
}
else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK3)
{
deviceaddress = NOR_MEMORY_ADRESS3;
}
else /* FSMC_NORSRAM_BANK4 */
{
deviceaddress = NOR_MEMORY_ADRESS4;
}
/* Send read data command */
if (hnor->CommandSet == NOR_AMD_FUJITSU_COMMAND_SET)
{
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_FIRST), NOR_CMD_DATA_FIRST);
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_SECOND), NOR_CMD_DATA_SECOND);
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_THIRD), NOR_CMD_DATA_READ_RESET);
}
else if (hnor->CommandSet == NOR_INTEL_SHARP_EXT_COMMAND_SET)
{
NOR_WRITE(deviceaddress, NOR_CMD_READ_ARRAY);
}
else
{
/* Primary command set not supported by the driver */
status = HAL_ERROR;
}
if (status != HAL_ERROR)
{
/* Read buffer */
while (size > 0U)
{
*data = *(__IO uint16_t *)address;
data++;
address += 2U;
size--;
}
}
/* Check the NOR controller state */
hnor->State = state;
/* Process unlocked */
__HAL_UNLOCK(hnor);
}
else
{
return HAL_ERROR;
}
return status;
}
/**
* @brief Writes a half-word buffer to the NOR memory. This function must be used
only with S29GL128P NOR memory.
* @param hnor pointer to the NOR handle
* @param uwAddress NOR memory internal start write address
* @param pData pointer to source data buffer.
* @param uwBufferSize Size of the buffer to write
* @retval HAL status
*/
HAL_StatusTypeDef HAL_NOR_ProgramBuffer(NOR_HandleTypeDef *hnor, uint32_t uwAddress, uint16_t *pData,
uint32_t uwBufferSize)
{
uint16_t *p_currentaddress;
const uint16_t *p_endaddress;
uint16_t *data = pData;
uint32_t deviceaddress;
HAL_StatusTypeDef status = HAL_OK;
/* Check the NOR controller state */
if (hnor->State == HAL_NOR_STATE_BUSY)
{
return HAL_BUSY;
}
else if (hnor->State == HAL_NOR_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hnor);
/* Update the NOR controller state */
hnor->State = HAL_NOR_STATE_BUSY;
/* Select the NOR device address */
if (hnor->Init.NSBank == FSMC_NORSRAM_BANK1)
{
deviceaddress = NOR_MEMORY_ADRESS1;
}
else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK2)
{
deviceaddress = NOR_MEMORY_ADRESS2;
}
else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK3)
{
deviceaddress = NOR_MEMORY_ADRESS3;
}
else /* FSMC_NORSRAM_BANK4 */
{
deviceaddress = NOR_MEMORY_ADRESS4;
}
/* Initialize variables */
p_currentaddress = (uint16_t *)(deviceaddress + uwAddress);
p_endaddress = (uint16_t *)(deviceaddress + uwAddress + (2U * (uwBufferSize - 1U)));
if (hnor->CommandSet == NOR_AMD_FUJITSU_COMMAND_SET)
{
/* Issue unlock command sequence */
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_FIRST), NOR_CMD_DATA_FIRST);
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_SECOND), NOR_CMD_DATA_SECOND);
/* Write Buffer Load Command */
NOR_WRITE((deviceaddress + uwAddress), NOR_CMD_DATA_BUFFER_AND_PROG);
NOR_WRITE((deviceaddress + uwAddress), (uint16_t)(uwBufferSize - 1U));
}
else if (hnor->CommandSet == NOR_INTEL_SHARP_EXT_COMMAND_SET)
{
/* Write Buffer Load Command */
NOR_WRITE((deviceaddress + uwAddress), NOR_CMD_BUFFERED_PROGRAM);
NOR_WRITE((deviceaddress + uwAddress), (uint16_t)(uwBufferSize - 1U));
}
else
{
/* Primary command set not supported by the driver */
status = HAL_ERROR;
}
if (status != HAL_ERROR)
{
/* Load Data into NOR Buffer */
while (p_currentaddress <= p_endaddress)
{
NOR_WRITE(p_currentaddress, *data);
data++;
p_currentaddress ++;
}
if (hnor->CommandSet == NOR_AMD_FUJITSU_COMMAND_SET)
{
NOR_WRITE((deviceaddress + uwAddress), NOR_CMD_DATA_BUFFER_AND_PROG_CONFIRM);
}
else /* => hnor->CommandSet == NOR_INTEL_SHARP_EXT_COMMAND_SET */
{
NOR_WRITE((deviceaddress + uwAddress), NOR_CMD_CONFIRM);
}
}
/* Check the NOR controller state */
hnor->State = HAL_NOR_STATE_READY;
/* Process unlocked */
__HAL_UNLOCK(hnor);
}
else
{
return HAL_ERROR;
}
return status;
}
/**
* @brief Erase the specified block of the NOR memory
* @param hnor pointer to a NOR_HandleTypeDef structure that contains
* the configuration information for NOR module.
* @param BlockAddress Block to erase address
* @param Address Device address
* @retval HAL status
*/
HAL_StatusTypeDef HAL_NOR_Erase_Block(NOR_HandleTypeDef *hnor, uint32_t BlockAddress, uint32_t Address)
{
uint32_t deviceaddress;
HAL_StatusTypeDef status = HAL_OK;
/* Check the NOR controller state */
if (hnor->State == HAL_NOR_STATE_BUSY)
{
return HAL_BUSY;
}
else if (hnor->State == HAL_NOR_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hnor);
/* Update the NOR controller state */
hnor->State = HAL_NOR_STATE_BUSY;
/* Select the NOR device address */
if (hnor->Init.NSBank == FSMC_NORSRAM_BANK1)
{
deviceaddress = NOR_MEMORY_ADRESS1;
}
else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK2)
{
deviceaddress = NOR_MEMORY_ADRESS2;
}
else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK3)
{
deviceaddress = NOR_MEMORY_ADRESS3;
}
else /* FSMC_NORSRAM_BANK4 */
{
deviceaddress = NOR_MEMORY_ADRESS4;
}
/* Send block erase command sequence */
if (hnor->CommandSet == NOR_AMD_FUJITSU_COMMAND_SET)
{
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_FIRST), NOR_CMD_DATA_FIRST);
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_SECOND), NOR_CMD_DATA_SECOND);
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_THIRD),
NOR_CMD_DATA_CHIP_BLOCK_ERASE_THIRD);
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_FOURTH),
NOR_CMD_DATA_CHIP_BLOCK_ERASE_FOURTH);
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_FIFTH),
NOR_CMD_DATA_CHIP_BLOCK_ERASE_FIFTH);
NOR_WRITE((uint32_t)(BlockAddress + Address), NOR_CMD_DATA_BLOCK_ERASE);
}
else if (hnor->CommandSet == NOR_INTEL_SHARP_EXT_COMMAND_SET)
{
NOR_WRITE((BlockAddress + Address), NOR_CMD_BLOCK_UNLOCK);
NOR_WRITE((BlockAddress + Address), NOR_CMD_CONFIRM);
NOR_WRITE((BlockAddress + Address), NOR_CMD_BLOCK_ERASE);
NOR_WRITE((BlockAddress + Address), NOR_CMD_CONFIRM);
}
else
{
/* Primary command set not supported by the driver */
status = HAL_ERROR;
}
/* Check the NOR memory status and update the controller state */
hnor->State = HAL_NOR_STATE_READY;
/* Process unlocked */
__HAL_UNLOCK(hnor);
}
else
{
return HAL_ERROR;
}
return status;
}
/**
* @brief Erase the entire NOR chip.
* @param hnor pointer to a NOR_HandleTypeDef structure that contains
* the configuration information for NOR module.
* @param Address Device address
* @retval HAL status
*/
HAL_StatusTypeDef HAL_NOR_Erase_Chip(NOR_HandleTypeDef *hnor, uint32_t Address)
{
uint32_t deviceaddress;
HAL_StatusTypeDef status = HAL_OK;
UNUSED(Address);
/* Check the NOR controller state */
if (hnor->State == HAL_NOR_STATE_BUSY)
{
return HAL_BUSY;
}
else if (hnor->State == HAL_NOR_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hnor);
/* Update the NOR controller state */
hnor->State = HAL_NOR_STATE_BUSY;
/* Select the NOR device address */
if (hnor->Init.NSBank == FSMC_NORSRAM_BANK1)
{
deviceaddress = NOR_MEMORY_ADRESS1;
}
else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK2)
{
deviceaddress = NOR_MEMORY_ADRESS2;
}
else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK3)
{
deviceaddress = NOR_MEMORY_ADRESS3;
}
else /* FSMC_NORSRAM_BANK4 */
{
deviceaddress = NOR_MEMORY_ADRESS4;
}
/* Send NOR chip erase command sequence */
if (hnor->CommandSet == NOR_AMD_FUJITSU_COMMAND_SET)
{
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_FIRST), NOR_CMD_DATA_FIRST);
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_SECOND), NOR_CMD_DATA_SECOND);
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_THIRD),
NOR_CMD_DATA_CHIP_BLOCK_ERASE_THIRD);
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_FOURTH),
NOR_CMD_DATA_CHIP_BLOCK_ERASE_FOURTH);
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_FIFTH),
NOR_CMD_DATA_CHIP_BLOCK_ERASE_FIFTH);
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_SIXTH), NOR_CMD_DATA_CHIP_ERASE);
}
else
{
/* Primary command set not supported by the driver */
status = HAL_ERROR;
}
/* Check the NOR memory status and update the controller state */
hnor->State = HAL_NOR_STATE_READY;
/* Process unlocked */
__HAL_UNLOCK(hnor);
}
else
{
return HAL_ERROR;
}
return status;
}
/**
* @brief Read NOR flash CFI IDs
* @param hnor pointer to a NOR_HandleTypeDef structure that contains
* the configuration information for NOR module.
* @param pNOR_CFI pointer to NOR CFI IDs structure
* @retval HAL status
*/
HAL_StatusTypeDef HAL_NOR_Read_CFI(NOR_HandleTypeDef *hnor, NOR_CFITypeDef *pNOR_CFI)
{
uint32_t deviceaddress;
HAL_NOR_StateTypeDef state;
/* Check the NOR controller state */
state = hnor->State;
if (state == HAL_NOR_STATE_BUSY)
{
return HAL_BUSY;
}
else if (state == HAL_NOR_STATE_PROTECTED)
{
return HAL_ERROR;
}
else if (state == HAL_NOR_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hnor);
/* Update the NOR controller state */
hnor->State = HAL_NOR_STATE_BUSY;
/* Select the NOR device address */
if (hnor->Init.NSBank == FSMC_NORSRAM_BANK1)
{
deviceaddress = NOR_MEMORY_ADRESS1;
}
else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK2)
{
deviceaddress = NOR_MEMORY_ADRESS2;
}
else if (hnor->Init.NSBank == FSMC_NORSRAM_BANK3)
{
deviceaddress = NOR_MEMORY_ADRESS3;
}
else /* FSMC_NORSRAM_BANK4 */
{
deviceaddress = NOR_MEMORY_ADRESS4;
}
/* Send read CFI query command */
NOR_WRITE(NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, NOR_CMD_ADDRESS_FIRST_CFI), NOR_CMD_DATA_CFI);
/* read the NOR CFI information */
pNOR_CFI->CFI_1 = *(__IO uint16_t *) NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, CFI1_ADDRESS);
pNOR_CFI->CFI_2 = *(__IO uint16_t *) NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, CFI2_ADDRESS);
pNOR_CFI->CFI_3 = *(__IO uint16_t *) NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, CFI3_ADDRESS);
pNOR_CFI->CFI_4 = *(__IO uint16_t *) NOR_ADDR_SHIFT(deviceaddress, uwNORMemoryDataWidth, CFI4_ADDRESS);
/* Check the NOR controller state */
hnor->State = state;
/* Process unlocked */
__HAL_UNLOCK(hnor);
}
else
{
return HAL_ERROR;
}
return HAL_OK;
}
#if (USE_HAL_NOR_REGISTER_CALLBACKS == 1)
/**
* @brief Register a User NOR Callback
* To be used instead of the weak (surcharged) predefined callback
* @param hnor : NOR handle
* @param CallbackId : ID of the callback to be registered
* This parameter can be one of the following values:
* @arg @ref HAL_NOR_MSP_INIT_CB_ID NOR MspInit callback ID
* @arg @ref HAL_NOR_MSP_DEINIT_CB_ID NOR MspDeInit callback ID
* @param pCallback : pointer to the Callback function
* @retval status
*/
HAL_StatusTypeDef HAL_NOR_RegisterCallback(NOR_HandleTypeDef *hnor, HAL_NOR_CallbackIDTypeDef CallbackId,
pNOR_CallbackTypeDef pCallback)
{
HAL_StatusTypeDef status = HAL_OK;
HAL_NOR_StateTypeDef state;
if (pCallback == NULL)
{
return HAL_ERROR;
}
/* Process locked */
__HAL_LOCK(hnor);
state = hnor->State;
if ((state == HAL_NOR_STATE_READY) || (state == HAL_NOR_STATE_RESET) || (state == HAL_NOR_STATE_PROTECTED))
{
switch (CallbackId)
{
case HAL_NOR_MSP_INIT_CB_ID :
hnor->MspInitCallback = pCallback;
break;
case HAL_NOR_MSP_DEINIT_CB_ID :
hnor->MspDeInitCallback = pCallback;
break;
default :
/* update return status */
status = HAL_ERROR;
break;
}
}
else
{
/* update return status */
status = HAL_ERROR;
}
/* Release Lock */
__HAL_UNLOCK(hnor);
return status;
}
/**
* @brief Unregister a User NOR Callback
* NOR Callback is redirected to the weak (surcharged) predefined callback
* @param hnor : NOR handle
* @param CallbackId : ID of the callback to be unregistered
* This parameter can be one of the following values:
* @arg @ref HAL_NOR_MSP_INIT_CB_ID NOR MspInit callback ID
* @arg @ref HAL_NOR_MSP_DEINIT_CB_ID NOR MspDeInit callback ID
* @retval status
*/
HAL_StatusTypeDef HAL_NOR_UnRegisterCallback(NOR_HandleTypeDef *hnor, HAL_NOR_CallbackIDTypeDef CallbackId)
{
HAL_StatusTypeDef status = HAL_OK;
HAL_NOR_StateTypeDef state;
/* Process locked */
__HAL_LOCK(hnor);
state = hnor->State;
if ((state == HAL_NOR_STATE_READY) || (state == HAL_NOR_STATE_RESET) || (state == HAL_NOR_STATE_PROTECTED))
{
switch (CallbackId)
{
case HAL_NOR_MSP_INIT_CB_ID :
hnor->MspInitCallback = HAL_NOR_MspInit;
break;
case HAL_NOR_MSP_DEINIT_CB_ID :
hnor->MspDeInitCallback = HAL_NOR_MspDeInit;
break;
default :
/* update return status */
status = HAL_ERROR;
break;
}
}
else
{
/* update return status */
status = HAL_ERROR;
}
/* Release Lock */
__HAL_UNLOCK(hnor);
return status;
}
#endif /* (USE_HAL_NOR_REGISTER_CALLBACKS) */
/**
* @}
*/
/** @defgroup NOR_Exported_Functions_Group3 NOR Control functions
* @brief management functions
*
@verbatim
==============================================================================
##### NOR Control functions #####
==============================================================================
[..]
This subsection provides a set of functions allowing to control dynamically
the NOR interface.
@endverbatim
* @{
*/
/**
* @brief Enables dynamically NOR write operation.
* @param hnor pointer to a NOR_HandleTypeDef structure that contains
* the configuration information for NOR module.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_NOR_WriteOperation_Enable(NOR_HandleTypeDef *hnor)
{
/* Check the NOR controller state */
if (hnor->State == HAL_NOR_STATE_PROTECTED)
{
/* Process Locked */
__HAL_LOCK(hnor);
/* Update the NOR controller state */
hnor->State = HAL_NOR_STATE_BUSY;
/* Enable write operation */
(void)FSMC_NORSRAM_WriteOperation_Enable(hnor->Instance, hnor->Init.NSBank);
/* Update the NOR controller state */
hnor->State = HAL_NOR_STATE_READY;
/* Process unlocked */
__HAL_UNLOCK(hnor);
}
else
{
return HAL_ERROR;
}
return HAL_OK;
}
/**
* @brief Disables dynamically NOR write operation.
* @param hnor pointer to a NOR_HandleTypeDef structure that contains
* the configuration information for NOR module.
* @retval HAL status
*/
HAL_StatusTypeDef HAL_NOR_WriteOperation_Disable(NOR_HandleTypeDef *hnor)
{
/* Check the NOR controller state */
if (hnor->State == HAL_NOR_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hnor);
/* Update the NOR controller state */
hnor->State = HAL_NOR_STATE_BUSY;
/* Disable write operation */
(void)FSMC_NORSRAM_WriteOperation_Disable(hnor->Instance, hnor->Init.NSBank);
/* Update the NOR controller state */
hnor->State = HAL_NOR_STATE_PROTECTED;
/* Process unlocked */
__HAL_UNLOCK(hnor);
}
else
{
return HAL_ERROR;
}
return HAL_OK;
}
/**
* @}
*/
/** @defgroup NOR_Exported_Functions_Group4 NOR State functions
* @brief Peripheral State functions
*
@verbatim
==============================================================================
##### NOR State functions #####
==============================================================================
[..]
This subsection permits to get in run-time the status of the NOR controller
and the data flow.
@endverbatim
* @{
*/
/**
* @brief return the NOR controller state
* @param hnor pointer to a NOR_HandleTypeDef structure that contains
* the configuration information for NOR module.
* @retval NOR controller state
*/
HAL_NOR_StateTypeDef HAL_NOR_GetState(NOR_HandleTypeDef *hnor)
{
return hnor->State;
}
/**
* @brief Returns the NOR operation status.
* @param hnor pointer to a NOR_HandleTypeDef structure that contains
* the configuration information for NOR module.
* @param Address Device address
* @param Timeout NOR programming Timeout
* @retval NOR_Status The returned value can be: HAL_NOR_STATUS_SUCCESS, HAL_NOR_STATUS_ERROR
* or HAL_NOR_STATUS_TIMEOUT
*/
HAL_NOR_StatusTypeDef HAL_NOR_GetStatus(NOR_HandleTypeDef *hnor, uint32_t Address, uint32_t Timeout)
{
HAL_NOR_StatusTypeDef status = HAL_NOR_STATUS_ONGOING;
uint16_t tmpsr1;
uint16_t tmpsr2;
uint32_t tickstart;
/* Poll on NOR memory Ready/Busy signal ------------------------------------*/
HAL_NOR_MspWait(hnor, Timeout);
/* Get the NOR memory operation status -------------------------------------*/
/* Get tick */
tickstart = HAL_GetTick();
if (hnor->CommandSet == NOR_AMD_FUJITSU_COMMAND_SET)
{
while ((status != HAL_NOR_STATUS_SUCCESS) && (status != HAL_NOR_STATUS_TIMEOUT))
{
/* Check for the Timeout */
if (Timeout != HAL_MAX_DELAY)
{
if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U))
{
status = HAL_NOR_STATUS_TIMEOUT;
}
}
/* Read NOR status register (DQ6 and DQ5) */
tmpsr1 = *(__IO uint16_t *)Address;
tmpsr2 = *(__IO uint16_t *)Address;
/* If DQ6 did not toggle between the two reads then return HAL_NOR_STATUS_SUCCESS */
if ((tmpsr1 & NOR_MASK_STATUS_DQ6) == (tmpsr2 & NOR_MASK_STATUS_DQ6))
{
return HAL_NOR_STATUS_SUCCESS ;
}
if ((tmpsr1 & NOR_MASK_STATUS_DQ5) == NOR_MASK_STATUS_DQ5)
{
status = HAL_NOR_STATUS_ONGOING;
}
tmpsr1 = *(__IO uint16_t *)Address;
tmpsr2 = *(__IO uint16_t *)Address;
/* If DQ6 did not toggle between the two reads then return HAL_NOR_STATUS_SUCCESS */
if ((tmpsr1 & NOR_MASK_STATUS_DQ6) == (tmpsr2 & NOR_MASK_STATUS_DQ6))
{
return HAL_NOR_STATUS_SUCCESS;
}
if ((tmpsr1 & NOR_MASK_STATUS_DQ5) == NOR_MASK_STATUS_DQ5)
{
return HAL_NOR_STATUS_ERROR;
}
}
}
else if (hnor->CommandSet == NOR_INTEL_SHARP_EXT_COMMAND_SET)
{
do
{
NOR_WRITE(Address, NOR_CMD_READ_STATUS_REG);
tmpsr2 = *(__IO uint16_t *)(Address);
/* Check for the Timeout */
if (Timeout != HAL_MAX_DELAY)
{
if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U))
{
return HAL_NOR_STATUS_TIMEOUT;
}
}
} while ((tmpsr2 & NOR_MASK_STATUS_DQ7) == 0U);
NOR_WRITE(Address, NOR_CMD_READ_STATUS_REG);
tmpsr1 = *(__IO uint16_t *)(Address);
if ((tmpsr1 & (NOR_MASK_STATUS_DQ5 | NOR_MASK_STATUS_DQ4)) != 0U)
{
/* Clear the Status Register */
NOR_WRITE(Address, NOR_CMD_READ_STATUS_REG);
status = HAL_NOR_STATUS_ERROR;
}
else
{
status = HAL_NOR_STATUS_SUCCESS;
}
}
else
{
/* Primary command set not supported by the driver */
status = HAL_NOR_STATUS_ERROR;
}
/* Return the operation status */
return status;
}
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#endif /* HAL_NOR_MODULE_ENABLED */
/**
* @}
*/
#endif /* FSMC_BANK1 */