WebSVN – canSerial – Blame – /trunk/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_ll_utils.c

Rev	Author	Line No.	Line
2	mjames	1	/**
		2	******************************************************************************
		3	* @file stm32f1xx_ll_utils.c
		4	* @author MCD Application Team
		5	* @brief UTILS LL module driver.
		6	******************************************************************************
		7	* @attention
		8	*
		9	* <h2><center>© Copyright (c) 2016 STMicroelectronics.
		10	* All rights reserved.</center></h2>
		11	*
		12	* This software component is licensed by ST under BSD 3-Clause license,
		13	* the "License"; You may not use this file except in compliance with the
		14	* License. You may obtain a copy of the License at:
		15	* opensource.org/licenses/BSD-3-Clause
		16	*
		17	******************************************************************************
		18	*/
		19
		20	/* Includes ------------------------------------------------------------------*/
		21	#include "stm32f1xx_ll_rcc.h"
		22	#include "stm32f1xx_ll_utils.h"
		23	#include "stm32f1xx_ll_system.h"
		24	#ifdef USE_FULL_ASSERT
		25	#include "stm32_assert.h"
		26	#else
		27	#define assert_param(expr) ((void)0U)
		28	#endif
		29
		30	/** @addtogroup STM32F1xx_LL_Driver
		31	* @{
		32	*/
		33
		34	/** @addtogroup UTILS_LL
		35	* @{
		36	*/
		37
		38	/* Private types -------------------------------------------------------------*/
		39	/* Private variables ---------------------------------------------------------*/
		40	/* Private constants ---------------------------------------------------------*/
		41	/** @addtogroup UTILS_LL_Private_Constants
		42	* @{
		43	*/
		44
		45	/* Defines used for PLL range */
		46	#define UTILS_PLL_OUTPUT_MAX RCC_MAX_FREQUENCY /!< Frequency max for PLL output, in Hz /
		47	#define UTILS_PLL2_OUTPUT_MAX RCC_MAX_FREQUENCY /!< Frequency max for PLL2 output, in Hz /
		48
		49	/* Defines used for HSE range */
		50	#define UTILS_HSE_FREQUENCY_MIN RCC_HSE_MIN /!< Frequency min for HSE frequency, in Hz /
		51	#define UTILS_HSE_FREQUENCY_MAX RCC_HSE_MAX /!< Frequency max for HSE frequency, in Hz /
		52
		53	/* Defines used for FLASH latency according to HCLK Frequency */
		54	#if defined(FLASH_ACR_LATENCY)
		55	#define UTILS_LATENCY1_FREQ 24000000U /!< SYSCLK frequency to set FLASH latency 1 /
		56	#define UTILS_LATENCY2_FREQ 48000000U /!< SYSCLK frequency to set FLASH latency 2 /
		57	#else
		58	/!< No Latency Configuration in this device /
		59	#endif
		60	/**
		61	* @}
		62	*/
		63	/* Private macros ------------------------------------------------------------*/
		64	/** @addtogroup UTILS_LL_Private_Macros
		65	* @{
		66	*/
		67	#define IS_LL_UTILS_SYSCLK_DIV(__VALUE__) (((__VALUE__) == LL_RCC_SYSCLK_DIV_1) \
		68	\|\| ((__VALUE__) == LL_RCC_SYSCLK_DIV_2) \
		69	\|\| ((__VALUE__) == LL_RCC_SYSCLK_DIV_4) \
		70	\|\| ((__VALUE__) == LL_RCC_SYSCLK_DIV_8) \
		71	\|\| ((__VALUE__) == LL_RCC_SYSCLK_DIV_16) \
		72	\|\| ((__VALUE__) == LL_RCC_SYSCLK_DIV_64) \
		73	\|\| ((__VALUE__) == LL_RCC_SYSCLK_DIV_128) \
		74	\|\| ((__VALUE__) == LL_RCC_SYSCLK_DIV_256) \
		75	\|\| ((__VALUE__) == LL_RCC_SYSCLK_DIV_512))
		76
		77	#define IS_LL_UTILS_APB1_DIV(__VALUE__) (((__VALUE__) == LL_RCC_APB1_DIV_1) \
		78	\|\| ((__VALUE__) == LL_RCC_APB1_DIV_2) \
		79	\|\| ((__VALUE__) == LL_RCC_APB1_DIV_4) \
		80	\|\| ((__VALUE__) == LL_RCC_APB1_DIV_8) \
		81	\|\| ((__VALUE__) == LL_RCC_APB1_DIV_16))
		82
		83	#define IS_LL_UTILS_APB2_DIV(__VALUE__) (((__VALUE__) == LL_RCC_APB2_DIV_1) \
		84	\|\| ((__VALUE__) == LL_RCC_APB2_DIV_2) \
		85	\|\| ((__VALUE__) == LL_RCC_APB2_DIV_4) \
		86	\|\| ((__VALUE__) == LL_RCC_APB2_DIV_8) \
		87	\|\| ((__VALUE__) == LL_RCC_APB2_DIV_16))
		88
		89	#if defined(RCC_CFGR_PLLMULL6_5)
		90	#define IS_LL_UTILS_PLLMUL_VALUE(__VALUE__) (((__VALUE__) == LL_RCC_PLL_MUL_4) \
		91	\|\| ((__VALUE__) == LL_RCC_PLL_MUL_5) \
		92	\|\| ((__VALUE__) == LL_RCC_PLL_MUL_6) \
		93	\|\| ((__VALUE__) == LL_RCC_PLL_MUL_7) \
		94	\|\| ((__VALUE__) == LL_RCC_PLL_MUL_8) \
		95	\|\| ((__VALUE__) == LL_RCC_PLL_MUL_9) \
		96	\|\| ((__VALUE__) == LL_RCC_PLL_MUL_6_5))
		97	#else
		98	#define IS_LL_UTILS_PLLMUL_VALUE(__VALUE__) (((__VALUE__) == LL_RCC_PLL_MUL_2) \
		99	\|\| ((__VALUE__) == LL_RCC_PLL_MUL_3) \
		100	\|\| ((__VALUE__) == LL_RCC_PLL_MUL_4) \
		101	\|\| ((__VALUE__) == LL_RCC_PLL_MUL_5) \
		102	\|\| ((__VALUE__) == LL_RCC_PLL_MUL_6) \
		103	\|\| ((__VALUE__) == LL_RCC_PLL_MUL_7) \
		104	\|\| ((__VALUE__) == LL_RCC_PLL_MUL_8) \
		105	\|\| ((__VALUE__) == LL_RCC_PLL_MUL_9) \
		106	\|\| ((__VALUE__) == LL_RCC_PLL_MUL_10) \
		107	\|\| ((__VALUE__) == LL_RCC_PLL_MUL_11) \
		108	\|\| ((__VALUE__) == LL_RCC_PLL_MUL_12) \
		109	\|\| ((__VALUE__) == LL_RCC_PLL_MUL_13) \
		110	\|\| ((__VALUE__) == LL_RCC_PLL_MUL_14) \
		111	\|\| ((__VALUE__) == LL_RCC_PLL_MUL_15) \
		112	\|\| ((__VALUE__) == LL_RCC_PLL_MUL_16))
		113	#endif /* RCC_CFGR_PLLMULL6_5 */
		114
		115	#if defined(RCC_CFGR2_PREDIV1)
		116	#define IS_LL_UTILS_PREDIV_VALUE(__VALUE__) (((__VALUE__) == LL_RCC_PREDIV_DIV_1) \|\| ((__VALUE__) == LL_RCC_PREDIV_DIV_2) \|\| \
		117	((__VALUE__) == LL_RCC_PREDIV_DIV_3) \|\| ((__VALUE__) == LL_RCC_PREDIV_DIV_4) \|\| \
		118	((__VALUE__) == LL_RCC_PREDIV_DIV_5) \|\| ((__VALUE__) == LL_RCC_PREDIV_DIV_6) \|\| \
		119	((__VALUE__) == LL_RCC_PREDIV_DIV_7) \|\| ((__VALUE__) == LL_RCC_PREDIV_DIV_8) \|\| \
		120	((__VALUE__) == LL_RCC_PREDIV_DIV_9) \|\| ((__VALUE__) == LL_RCC_PREDIV_DIV_10) \|\| \
		121	((__VALUE__) == LL_RCC_PREDIV_DIV_11) \|\| ((__VALUE__) == LL_RCC_PREDIV_DIV_12) \|\| \
		122	((__VALUE__) == LL_RCC_PREDIV_DIV_13) \|\| ((__VALUE__) == LL_RCC_PREDIV_DIV_14) \|\| \
		123	((__VALUE__) == LL_RCC_PREDIV_DIV_15) \|\| ((__VALUE__) == LL_RCC_PREDIV_DIV_16))
		124	#else
		125	#define IS_LL_UTILS_PREDIV_VALUE(__VALUE__) (((__VALUE__) == LL_RCC_PREDIV_DIV_1) \|\| ((__VALUE__) == LL_RCC_PREDIV_DIV_2))
		126	#endif /RCC_PREDIV1_DIV_2_16_SUPPORT/
		127
		128	#define IS_LL_UTILS_PLL_FREQUENCY(__VALUE__) ((__VALUE__) <= UTILS_PLL_OUTPUT_MAX)
		129
		130	#if defined(RCC_PLL2_SUPPORT)
		131	#define IS_LL_UTILS_PLL2MUL_VALUE(__VALUE__) (((__VALUE__) == LL_RCC_PLL2_MUL_8) \
		132	\|\| ((__VALUE__) == LL_RCC_PLL2_MUL_9) \
		133	\|\| ((__VALUE__) == LL_RCC_PLL2_MUL_10) \
		134	\|\| ((__VALUE__) == LL_RCC_PLL2_MUL_11) \
		135	\|\| ((__VALUE__) == LL_RCC_PLL2_MUL_12) \
		136	\|\| ((__VALUE__) == LL_RCC_PLL2_MUL_13) \
		137	\|\| ((__VALUE__) == LL_RCC_PLL2_MUL_14) \
		138	\|\| ((__VALUE__) == LL_RCC_PLL2_MUL_16) \
		139	\|\| ((__VALUE__) == LL_RCC_PLL2_MUL_20))
		140
		141	#define IS_LL_UTILS_PREDIV2_VALUE(__VALUE__) (((__VALUE__) == LL_RCC_HSE_PREDIV2_DIV_1) \|\| ((__VALUE__) == LL_RCC_HSE_PREDIV2_DIV_2) \|\| \
		142	((__VALUE__) == LL_RCC_HSE_PREDIV2_DIV_3) \|\| ((__VALUE__) == LL_RCC_HSE_PREDIV2_DIV_4) \|\| \
		143	((__VALUE__) == LL_RCC_HSE_PREDIV2_DIV_5) \|\| ((__VALUE__) == LL_RCC_HSE_PREDIV2_DIV_6) \|\| \
		144	((__VALUE__) == LL_RCC_HSE_PREDIV2_DIV_7) \|\| ((__VALUE__) == LL_RCC_HSE_PREDIV2_DIV_8) \|\| \
		145	((__VALUE__) == LL_RCC_HSE_PREDIV2_DIV_9) \|\| ((__VALUE__) == LL_RCC_HSE_PREDIV2_DIV_10) \|\| \
		146	((__VALUE__) == LL_RCC_HSE_PREDIV2_DIV_11) \|\| ((__VALUE__) == LL_RCC_HSE_PREDIV2_DIV_12) \|\| \
		147	((__VALUE__) == LL_RCC_HSE_PREDIV2_DIV_13) \|\| ((__VALUE__) == LL_RCC_HSE_PREDIV2_DIV_14) \|\| \
		148	((__VALUE__) == LL_RCC_HSE_PREDIV2_DIV_15) \|\| ((__VALUE__) == LL_RCC_HSE_PREDIV2_DIV_16))
		149
		150	#define IS_LL_UTILS_PLL2_FREQUENCY(__VALUE__) ((__VALUE__) <= UTILS_PLL2_OUTPUT_MAX)
		151	#endif /* RCC_PLL2_SUPPORT */
		152
		153	#define IS_LL_UTILS_HSE_BYPASS(__STATE__) (((__STATE__) == LL_UTILS_HSEBYPASS_ON) \
		154	\|\| ((__STATE__) == LL_UTILS_HSEBYPASS_OFF))
		155
		156	#define IS_LL_UTILS_HSE_FREQUENCY(__FREQUENCY__) (((__FREQUENCY__) >= UTILS_HSE_FREQUENCY_MIN) && ((__FREQUENCY__) <= UTILS_HSE_FREQUENCY_MAX))
		157	/**
		158	* @}
		159	*/
		160	/* Private function prototypes -----------------------------------------------*/
		161	/** @defgroup UTILS_LL_Private_Functions UTILS Private functions
		162	* @{
		163	*/
		164	static uint32_t UTILS_GetPLLOutputFrequency(uint32_t PLL_InputFrequency,
		165	LL_UTILS_PLLInitTypeDef *UTILS_PLLInitStruct);
		166	static ErrorStatus UTILS_PLL_HSE_ConfigSystemClock(uint32_t PLL_InputFrequency, uint32_t HSEBypass,
		167	LL_UTILS_PLLInitTypeDef *UTILS_PLLInitStruct,
		168	LL_UTILS_ClkInitTypeDef *UTILS_ClkInitStruct);
		169	#if defined(RCC_PLL2_SUPPORT)
		170	static uint32_t UTILS_GetPLL2OutputFrequency(uint32_t PLL2_InputFrequency,
		171	LL_UTILS_PLLInitTypeDef *UTILS_PLL2InitStruct);
		172	#endif /* RCC_PLL2_SUPPORT */
		173	static ErrorStatus UTILS_EnablePLLAndSwitchSystem(uint32_t SYSCLK_Frequency, LL_UTILS_ClkInitTypeDef *UTILS_ClkInitStruct);
		174	static ErrorStatus UTILS_PLL_IsBusy(void);
		175	/**
		176	* @}
		177	*/
		178
		179	/* Exported functions --------------------------------------------------------*/
		180	/** @addtogroup UTILS_LL_Exported_Functions
		181	* @{
		182	*/
		183
		184	/** @addtogroup UTILS_LL_EF_DELAY
		185	* @{
		186	*/
		187
		188	/**
		189	* @brief This function configures the Cortex-M SysTick source to have 1ms time base.
		190	* @note When a RTOS is used, it is recommended to avoid changing the Systick
		191	* configuration by calling this function, for a delay use rather osDelay RTOS service.
		192	* @param HCLKFrequency HCLK frequency in Hz
		193	* @note HCLK frequency can be calculated thanks to RCC helper macro or function @ref LL_RCC_GetSystemClocksFreq
		194	* @retval None
		195	*/
		196	void LL_Init1msTick(uint32_t HCLKFrequency)
		197	{
		198	/* Use frequency provided in argument */
		199	LL_InitTick(HCLKFrequency, 1000U);
		200	}
		201
		202	/**
		203	* @brief This function provides accurate delay (in milliseconds) based
		204	* on SysTick counter flag
		205	* @note When a RTOS is used, it is recommended to avoid using blocking delay
		206	* and use rather osDelay service.
		207	* @note To respect 1ms timebase, user should call @ref LL_Init1msTick function which
		208	* will configure Systick to 1ms
		209	* @param Delay specifies the delay time length, in milliseconds.
		210	* @retval None
		211	*/
		212	void LL_mDelay(uint32_t Delay)
		213	{
		214	__IO uint32_t tmp = SysTick->CTRL; /* Clear the COUNTFLAG first */
		215	/* Add this code to indicate that local variable is not used */
		216	((void)tmp);
		217
		218	/* Add a period to guaranty minimum wait */
		219	if (Delay < LL_MAX_DELAY)
		220	{
		221	Delay++;
		222	}
		223
		224	while (Delay)
		225	{
		226	if ((SysTick->CTRL & SysTick_CTRL_COUNTFLAG_Msk) != 0U)
		227	{
		228	Delay--;
		229	}
		230	}
		231	}
		232
		233	/**
		234	* @}
		235	*/
		236
		237	/** @addtogroup UTILS_EF_SYSTEM
		238	* @brief System Configuration functions
		239	*
		240	@verbatim
		241	===============================================================================
		242	##### System Configuration functions #####
		243	===============================================================================
		244	[..]
		245	System, AHB and APB buses clocks configuration
		246
		247	(+) The maximum frequency of the SYSCLK, HCLK, PCLK1 and PCLK2 is RCC_MAX_FREQUENCY Hz.
		248	@endverbatim
		249	@internal
		250	Depending on the SYSCLK frequency, the flash latency should be adapted accordingly:
		251	(++) +-----------------------------------------------+
		252	(++) \| Latency \| SYSCLK clock frequency (MHz) \|
		253	(++) \|---------------\|-------------------------------\|
		254	(++) \|0WS(1CPU cycle)\| 0 < SYSCLK <= 24 \|
		255	(++) \|---------------\|-------------------------------\|
		256	(++) \|1WS(2CPU cycle)\| 24 < SYSCLK <= 48 \|
		257	(++) \|---------------\|-------------------------------\|
		258	(++) \|2WS(3CPU cycle)\| 48 < SYSCLK <= 72 \|
		259	(++) +-----------------------------------------------+
		260	@endinternal
		261	* @{
		262	*/
		263
		264	/**
		265	* @brief This function sets directly SystemCoreClock CMSIS variable.
		266	* @note Variable can be calculated also through SystemCoreClockUpdate function.
		267	* @param HCLKFrequency HCLK frequency in Hz (can be calculated thanks to RCC helper macro)
		268	* @retval None
		269	*/
		270	void LL_SetSystemCoreClock(uint32_t HCLKFrequency)
		271	{
		272	/* HCLK clock frequency */
		273	SystemCoreClock = HCLKFrequency;
		274	}
		275
		276	/**
		277	* @brief Update number of Flash wait states in line with new frequency and current
		278	voltage range.
		279	* @param Frequency SYSCLK frequency
		280	* @retval An ErrorStatus enumeration value:
		281	* - SUCCESS: Latency has been modified
		282	* - ERROR: Latency cannot be modified
		283	*/
		284	#if defined(FLASH_ACR_LATENCY)
		285	ErrorStatus LL_SetFlashLatency(uint32_t Frequency)
		286	{
		287	uint32_t timeout;
		288	uint32_t getlatency;
		289	uint32_t latency = LL_FLASH_LATENCY_0; /* default value 0WS */
		290	ErrorStatus status = SUCCESS;
		291
		292	/* Frequency cannot be equal to 0 */
		293	if (Frequency == 0U)
		294	{
		295	status = ERROR;
		296	}
		297	else
		298	{
		299	if (Frequency > UTILS_LATENCY2_FREQ)
		300	{
		301	/* 48 < SYSCLK <= 72 => 2WS (3 CPU cycles) */
		302	latency = LL_FLASH_LATENCY_2;
		303	}
		304	else
		305	{
		306	if (Frequency > UTILS_LATENCY1_FREQ)
		307	{
		308	/* 24 < SYSCLK <= 48 => 1WS (2 CPU cycles) */
		309	latency = LL_FLASH_LATENCY_1;
		310	}
		311	else
		312	{
		313	/* else SYSCLK < 24MHz default LL_FLASH_LATENCY_0 0WS */
		314	latency = LL_FLASH_LATENCY_0;
		315	}
		316	}
		317
		318	if (status != ERROR)
		319	{
		320	LL_FLASH_SetLatency(latency);
		321
		322	/* Check that the new number of wait states is taken into account to access the Flash
		323	memory by reading the FLASH_ACR register */
		324	timeout = 2;
		325	do
		326	{
		327	/* Wait for Flash latency to be updated */
		328	getlatency = LL_FLASH_GetLatency();
		329	timeout--;
		330	}
		331	while ((getlatency != latency) && (timeout > 0));
		332
		333	if (getlatency != latency)
		334	{
		335	status = ERROR;
		336	}
		337	else
		338	{
		339	status = SUCCESS;
		340	}
		341	}
		342	}
		343
		344	return status;
		345	}
		346	#endif /* FLASH_ACR_LATENCY */
		347
		348	/**
		349	* @brief This function configures system clock with HSI as clock source of the PLL
		350	* @note The application need to ensure that PLL is disabled.
		351	* @note Function is based on the following formula:
		352	* - PLL output frequency = ((HSI frequency / PREDIV) * PLLMUL)
		353	* - PREDIV: Set to 2 for few devices
		354	* - PLLMUL: The application software must set correctly the PLL multiplication factor to
		355	* not exceed 72MHz
		356	* @note FLASH latency can be modified through this function.
		357	* @param UTILS_PLLInitStruct pointer to a @ref LL_UTILS_PLLInitTypeDef structure that contains
		358	* the configuration information for the PLL.
		359	* @param UTILS_ClkInitStruct pointer to a @ref LL_UTILS_ClkInitTypeDef structure that contains
		360	* the configuration information for the BUS prescalers.
		361	* @retval An ErrorStatus enumeration value:
		362	* - SUCCESS: Max frequency configuration done
		363	* - ERROR: Max frequency configuration not done
		364	*/
		365	ErrorStatus LL_PLL_ConfigSystemClock_HSI(LL_UTILS_PLLInitTypeDef *UTILS_PLLInitStruct,
		366	LL_UTILS_ClkInitTypeDef *UTILS_ClkInitStruct)
		367	{
		368	ErrorStatus status = SUCCESS;
		369	uint32_t pllfreq = 0U;
		370
		371	/* Check if one of the PLL is enabled */
		372	if (UTILS_PLL_IsBusy() == SUCCESS)
		373	{
		374	#if defined(RCC_PLLSRC_PREDIV1_SUPPORT)
		375	/* Check PREDIV value */
		376	assert_param(IS_LL_UTILS_PREDIV_VALUE(UTILS_PLLInitStruct->PLLDiv));
		377	#else
		378	/* Force PREDIV value to 2 */
		379	UTILS_PLLInitStruct->Prediv = LL_RCC_PREDIV_DIV_2;
		380	#endif /RCC_PLLSRC_PREDIV1_SUPPORT/
		381	/* Calculate the new PLL output frequency */
		382	pllfreq = UTILS_GetPLLOutputFrequency(HSI_VALUE, UTILS_PLLInitStruct);
		383
		384	/* Enable HSI if not enabled */
		385	if (LL_RCC_HSI_IsReady() != 1U)
		386	{
		387	LL_RCC_HSI_Enable();
		388	while (LL_RCC_HSI_IsReady() != 1U)
		389	{
		390	/* Wait for HSI ready */
		391	}
		392	}
		393
		394	/* Configure PLL */
		395	LL_RCC_PLL_ConfigDomain_SYS(LL_RCC_PLLSOURCE_HSI_DIV_2, UTILS_PLLInitStruct->PLLMul);
		396
		397	/* Enable PLL and switch system clock to PLL */
		398	status = UTILS_EnablePLLAndSwitchSystem(pllfreq, UTILS_ClkInitStruct);
		399	}
		400	else
		401	{
		402	/* Current PLL configuration cannot be modified */
		403	status = ERROR;
		404	}
		405
		406	return status;
		407	}
		408
		409	/**
		410	* @brief This function configures system clock with HSE as clock source of the PLL
		411	* @note The application need to ensure that PLL is disabled.
		412	* @note Function is based on the following formula:
		413	* - PLL output frequency = ((HSI frequency / PREDIV) * PLLMUL)
		414	* - PREDIV: Set to 2 for few devices
		415	* - PLLMUL: The application software must set correctly the PLL multiplication factor to
		416	* not exceed @ref UTILS_PLL_OUTPUT_MAX
		417	* @note FLASH latency can be modified through this function.
		418	* @param HSEFrequency Value between Min_Data = RCC_HSE_MIN and Max_Data = RCC_HSE_MAX
		419	* @param HSEBypass This parameter can be one of the following values:
		420	* @arg @ref LL_UTILS_HSEBYPASS_ON
		421	* @arg @ref LL_UTILS_HSEBYPASS_OFF
		422	* @param UTILS_PLLInitStruct pointer to a @ref LL_UTILS_PLLInitTypeDef structure that contains
		423	* the configuration information for the PLL.
		424	* @param UTILS_ClkInitStruct pointer to a @ref LL_UTILS_ClkInitTypeDef structure that contains
		425	* the configuration information for the BUS prescalers.
		426	* @retval An ErrorStatus enumeration value:
		427	* - SUCCESS: Max frequency configuration done
		428	* - ERROR: Max frequency configuration not done
		429	*/
		430	ErrorStatus LL_PLL_ConfigSystemClock_HSE(uint32_t HSEFrequency, uint32_t HSEBypass,
		431	LL_UTILS_PLLInitTypeDef UTILS_PLLInitStruct, LL_UTILS_ClkInitTypeDef UTILS_ClkInitStruct)
		432	{
		433	ErrorStatus status = SUCCESS;
		434	uint32_t pllfrequency = 0U;
		435
		436	/* Check the parameters */
		437	assert_param(IS_LL_UTILS_HSE_FREQUENCY(HSEFrequency));
		438	assert_param(IS_LL_UTILS_HSE_BYPASS(HSEBypass));
		439	assert_param(IS_LL_UTILS_PREDIV_VALUE(UTILS_PLLInitStruct->Prediv));
		440
		441	/* Calculate the new PLL output frequency */
		442	pllfrequency = UTILS_GetPLLOutputFrequency(HSEFrequency, UTILS_PLLInitStruct);
		443
		444	/* Enable HSE if not enabled */
		445	status = UTILS_PLL_HSE_ConfigSystemClock(HSEFrequency, HSEBypass, UTILS_PLLInitStruct, UTILS_ClkInitStruct);
		446
		447	/* Check if HSE is not enabled*/
		448	if (status == SUCCESS)
		449	{
		450	/* Configure PLL */
		451	LL_RCC_PLL_ConfigDomain_SYS((LL_RCC_PLLSOURCE_HSE \| UTILS_PLLInitStruct->Prediv), UTILS_PLLInitStruct->PLLMul);
		452
		453	/* Enable PLL and switch system clock to PLL */
		454	status = UTILS_EnablePLLAndSwitchSystem(pllfrequency, UTILS_ClkInitStruct);
		455	}
		456
		457	return status;
		458	}
		459
		460	#if defined(RCC_PLL2_SUPPORT)
		461	/**
		462	* @brief This function configures system clock with HSE as clock source of the PLL, via PLL2
		463	* @note The application need to ensure that PLL and PLL2 are disabled.
		464	* @note Function is based on the following formula:
		465	* - PLL output frequency = ((((HSE frequency / PREDIV2) * PLL2MUL) / PREDIV) * PLLMUL)
		466	* - PREDIV, PLLMUL, PREDIV2, PLL2MUL: The application software must set correctly the
		467	* PLL multiplication factor to not exceed @ref UTILS_PLL_OUTPUT_MAX
		468	* @note FLASH latency can be modified through this function.
		469	* @param HSEFrequency Value between Min_Data = RCC_HSE_MIN and Max_Data = RCC_HSE_MAX
		470	* @param HSEBypass This parameter can be one of the following values:
		471	* @arg @ref LL_UTILS_HSEBYPASS_ON
		472	* @arg @ref LL_UTILS_HSEBYPASS_OFF
		473	* @param UTILS_PLLInitStruct pointer to a @ref LL_UTILS_PLLInitTypeDef structure that contains
		474	* the configuration information for the PLL.
		475	* @param UTILS_PLL2InitStruct pointer to a @ref LL_UTILS_PLLInitTypeDef structure that contains
		476	* the configuration information for the PLL2.
		477	* @param UTILS_ClkInitStruct pointer to a @ref LL_UTILS_ClkInitTypeDef structure that contains
		478	* the configuration information for the BUS prescalers.
		479	* @retval An ErrorStatus enumeration value:
		480	* - SUCCESS: Max frequency configuration done
		481	* - ERROR: Max frequency configuration not done
		482	*/
		483	ErrorStatus LL_PLL_ConfigSystemClock_PLL2(uint32_t HSEFrequency, uint32_t HSEBypass,
		484	LL_UTILS_PLLInitTypeDef *UTILS_PLLInitStruct,
		485	LL_UTILS_PLLInitTypeDef *UTILS_PLL2InitStruct,
		486	LL_UTILS_ClkInitTypeDef *UTILS_ClkInitStruct)
		487	{
		488	ErrorStatus status = SUCCESS;
		489	uint32_t pllfrequency = 0U;
		490
		491	/* Check the parameters */
		492	assert_param(IS_LL_UTILS_HSE_FREQUENCY(HSEFrequency));
		493	assert_param(IS_LL_UTILS_HSE_BYPASS(HSEBypass));
		494	assert_param(IS_LL_UTILS_PREDIV_VALUE(UTILS_PLLInitStruct->Prediv));
		495	assert_param(IS_LL_UTILS_PREDIV2_VALUE(UTILS_PLL2InitStruct->Prediv));
		496
		497	/* Calculate the new PLL output frequency */
		498	pllfrequency = UTILS_GetPLLOutputFrequency(HSEFrequency, UTILS_PLLInitStruct);
		499
		500	/* Enable HSE if not enabled */
		501	status = UTILS_PLL_HSE_ConfigSystemClock(HSEFrequency, HSEBypass, UTILS_PLLInitStruct, UTILS_ClkInitStruct);
		502
		503	/* Check if HSE is not enabled*/
		504	if (status == SUCCESS)
		505	{
		506	/* Configure PLL */
		507	LL_RCC_PLL_ConfigDomain_PLL2(UTILS_PLL2InitStruct->Prediv, UTILS_PLL2InitStruct->PLLMul);
		508	LL_RCC_PLL_ConfigDomain_SYS((LL_RCC_PLLSOURCE_PLL2 \| UTILS_PLLInitStruct->Prediv), UTILS_PLLInitStruct->PLLMul);
		509
		510	/* Calculate the new PLL output frequency */
		511	pllfrequency = UTILS_GetPLL2OutputFrequency(pllfrequency, UTILS_PLL2InitStruct);
		512
		513	/* Enable PLL and switch system clock to PLL */
		514	status = UTILS_EnablePLLAndSwitchSystem(pllfrequency, UTILS_ClkInitStruct);
		515	}
		516
		517	return status;
		518	}
		519	#endif /* RCC_PLL2_SUPPORT */
		520
		521	/**
		522	* @}
		523	*/
		524
		525	/**
		526	* @}
		527	*/
		528
		529	/** @addtogroup UTILS_LL_Private_Functions
		530	* @{
		531	*/
		532	/**
		533	* @brief Function to check that PLL can be modified
		534	* @param PLL_InputFrequency PLL input frequency (in Hz)
		535	* @param UTILS_PLLInitStruct pointer to a @ref LL_UTILS_PLLInitTypeDef structure that contains
		536	* the configuration information for the PLL.
		537	* @retval PLL output frequency (in Hz)
		538	*/
		539	static uint32_t UTILS_GetPLLOutputFrequency(uint32_t PLL_InputFrequency, LL_UTILS_PLLInitTypeDef *UTILS_PLLInitStruct)
		540	{
		541	uint32_t pllfreq = 0U;
		542
		543	/* Check the parameters */
		544	assert_param(IS_LL_UTILS_PLLMUL_VALUE(UTILS_PLLInitStruct->PLLMul));
		545
		546	/* Check different PLL parameters according to RM */
		547	#if defined (RCC_CFGR2_PREDIV1)
		548	pllfreq = __LL_RCC_CALC_PLLCLK_FREQ(PLL_InputFrequency / (UTILS_PLLInitStruct->Prediv + 1U), UTILS_PLLInitStruct->PLLMul);
		549	#else
		550	pllfreq = __LL_RCC_CALC_PLLCLK_FREQ(PLL_InputFrequency / ((UTILS_PLLInitStruct->Prediv >> RCC_CFGR_PLLXTPRE_Pos) + 1U), UTILS_PLLInitStruct->PLLMul);
		551	#endif /RCC_CFGR2_PREDIV1SRC/
		552	assert_param(IS_LL_UTILS_PLL_FREQUENCY(pllfreq));
		553
		554	return pllfreq;
		555	}
		556
		557	/**
		558	* @brief This function enable the HSE when it is used by PLL or PLL2
		559	* @note The application need to ensure that PLL is disabled.
		560	* @param HSEFrequency Value between Min_Data = RCC_HSE_MIN and Max_Data = RCC_HSE_MAX
		561	* @param HSEBypass This parameter can be one of the following values:
		562	* @arg @ref LL_UTILS_HSEBYPASS_ON
		563	* @arg @ref LL_UTILS_HSEBYPASS_OFF
		564	* @param UTILS_PLLInitStruct pointer to a @ref LL_UTILS_PLLInitTypeDef structure that contains
		565	* the configuration information for the PLL.
		566	* @param UTILS_ClkInitStruct pointer to a @ref LL_UTILS_ClkInitTypeDef structure that contains
		567	* the configuration information for the BUS prescalers.
		568	* @retval An ErrorStatus enumeration value:
		569	* - SUCCESS: HSE configuration done
		570	* - ERROR: HSE configuration not done
		571	*/
		572	static ErrorStatus UTILS_PLL_HSE_ConfigSystemClock(uint32_t PLL_InputFrequency, uint32_t HSEBypass,
		573	LL_UTILS_PLLInitTypeDef *UTILS_PLLInitStruct,
		574	LL_UTILS_ClkInitTypeDef *UTILS_ClkInitStruct)
		575	{
		576	ErrorStatus status = SUCCESS;
		577
		578	/* Check if one of the PLL is enabled */
		579	if (UTILS_PLL_IsBusy() == SUCCESS)
		580	{
		581	/* Enable HSE if not enabled */
		582	if (LL_RCC_HSE_IsReady() != 1U)
		583	{
		584	/* Check if need to enable HSE bypass feature or not */
		585	if (HSEBypass == LL_UTILS_HSEBYPASS_ON)
		586	{
		587	LL_RCC_HSE_EnableBypass();
		588	}
		589	else
		590	{
		591	LL_RCC_HSE_DisableBypass();
		592	}
		593
		594	/* Enable HSE */
		595	LL_RCC_HSE_Enable();
		596	while (LL_RCC_HSE_IsReady() != 1U)
		597	{
		598	/* Wait for HSE ready */
		599	}
		600	}
		601	}
		602	else
		603	{
		604	/* Current PLL configuration cannot be modified */
		605	status = ERROR;
		606	}
		607
		608	return status;
		609	}
		610
		611	#if defined(RCC_PLL2_SUPPORT)
		612	/**
		613	* @brief Function to check that PLL2 can be modified
		614	* @param PLL2_InputFrequency PLL2 input frequency (in Hz)
		615	* @param UTILS_PLL2InitStruct pointer to a @ref LL_UTILS_PLLInitTypeDef structure that contains
		616	* the configuration information for the PLL.
		617	* @retval PLL2 output frequency (in Hz)
		618	*/
		619	static uint32_t UTILS_GetPLL2OutputFrequency(uint32_t PLL2_InputFrequency, LL_UTILS_PLLInitTypeDef *UTILS_PLL2InitStruct)
		620	{
		621	uint32_t pll2freq = 0U;
		622
		623	/* Check the parameters */
		624	assert_param(IS_LL_UTILS_PLL2MUL_VALUE(UTILS_PLL2InitStruct->PLLMul));
		625	assert_param(IS_LL_UTILS_PREDIV2_VALUE(UTILS_PLL2InitStruct->Prediv));
		626
		627	/* Check different PLL2 parameters according to RM */
		628	pll2freq = __LL_RCC_CALC_PLL2CLK_FREQ(PLL2_InputFrequency, UTILS_PLL2InitStruct->PLLMul, UTILS_PLL2InitStruct->Prediv);
		629	assert_param(IS_LL_UTILS_PLL2_FREQUENCY(pll2freq));
		630
		631	return pll2freq;
		632	}
		633	#endif /* RCC_PLL2_SUPPORT */
		634
		635	/**
		636	* @brief Function to check that PLL can be modified
		637	* @retval An ErrorStatus enumeration value:
		638	* - SUCCESS: PLL modification can be done
		639	* - ERROR: PLL is busy
		640	*/
		641	static ErrorStatus UTILS_PLL_IsBusy(void)
		642	{
		643	ErrorStatus status = SUCCESS;
		644
		645	/* Check if PLL is busy*/
		646	if (LL_RCC_PLL_IsReady() != 0U)
		647	{
		648	/* PLL configuration cannot be modified */
		649	status = ERROR;
		650	}
		651	#if defined(RCC_PLL2_SUPPORT)
		652	/* Check if PLL2 is busy*/
		653	if (LL_RCC_PLL2_IsReady() != 0U)
		654	{
		655	/* PLL2 configuration cannot be modified */
		656	status = ERROR;
		657	}
		658	#endif /* RCC_PLL2_SUPPORT */
		659
		660	#if defined(RCC_PLLI2S_SUPPORT)
		661	/* Check if PLLI2S is busy*/
		662	if (LL_RCC_PLLI2S_IsReady() != 0U)
		663	{
		664	/* PLLI2S configuration cannot be modified */
		665	status = ERROR;
		666	}
		667	#endif /* RCC_PLLI2S_SUPPORT */
		668
		669	return status;
		670	}
		671
		672	/**
		673	* @brief Function to enable PLL and switch system clock to PLL
		674	* @param SYSCLK_Frequency SYSCLK frequency
		675	* @param UTILS_ClkInitStruct pointer to a @ref LL_UTILS_ClkInitTypeDef structure that contains
		676	* the configuration information for the BUS prescalers.
		677	* @retval An ErrorStatus enumeration value:
		678	* - SUCCESS: No problem to switch system to PLL
		679	* - ERROR: Problem to switch system to PLL
		680	*/
		681	static ErrorStatus UTILS_EnablePLLAndSwitchSystem(uint32_t SYSCLK_Frequency, LL_UTILS_ClkInitTypeDef *UTILS_ClkInitStruct)
		682	{
		683	ErrorStatus status = SUCCESS;
		684	#if defined(FLASH_ACR_LATENCY)
		685	uint32_t sysclk_frequency_current = 0U;
		686	#endif /* FLASH_ACR_LATENCY */
		687
		688	assert_param(IS_LL_UTILS_SYSCLK_DIV(UTILS_ClkInitStruct->AHBCLKDivider));
		689	assert_param(IS_LL_UTILS_APB1_DIV(UTILS_ClkInitStruct->APB1CLKDivider));
		690	assert_param(IS_LL_UTILS_APB2_DIV(UTILS_ClkInitStruct->APB2CLKDivider));
		691
		692	#if defined(FLASH_ACR_LATENCY)
		693	/* Calculate current SYSCLK frequency */
		694	sysclk_frequency_current = (SystemCoreClock << AHBPrescTable[LL_RCC_GetAHBPrescaler() >> RCC_CFGR_HPRE_Pos]);
		695	#endif /* FLASH_ACR_LATENCY */
		696
		697	/* Increasing the number of wait states because of higher CPU frequency */
		698	#if defined (FLASH_ACR_LATENCY)
		699	if (sysclk_frequency_current < SYSCLK_Frequency)
		700	{
		701	/* Set FLASH latency to highest latency */
		702	status = LL_SetFlashLatency(SYSCLK_Frequency);
		703	}
		704	#endif /* FLASH_ACR_LATENCY */
		705
		706	/* Update system clock configuration */
		707	if (status == SUCCESS)
		708	{
		709	#if defined(RCC_PLL2_SUPPORT)
		710	if (LL_RCC_PLL_GetMainSource() != LL_RCC_PLLSOURCE_HSI_DIV_2)
		711	{
		712	/* Enable PLL2 */
		713	LL_RCC_PLL2_Enable();
		714	while (LL_RCC_PLL2_IsReady() != 1U)
		715	{
		716	/* Wait for PLL2 ready */
		717	}
		718	}
		719	#endif /* RCC_PLL2_SUPPORT */
		720	/* Enable PLL */
		721	LL_RCC_PLL_Enable();
		722	while (LL_RCC_PLL_IsReady() != 1U)
		723	{
		724	/* Wait for PLL ready */
		725	}
		726
		727	/* Sysclk activation on the main PLL */
		728	LL_RCC_SetAHBPrescaler(UTILS_ClkInitStruct->AHBCLKDivider);
		729	LL_RCC_SetSysClkSource(LL_RCC_SYS_CLKSOURCE_PLL);
		730	while (LL_RCC_GetSysClkSource() != LL_RCC_SYS_CLKSOURCE_STATUS_PLL)
		731	{
		732	/* Wait for system clock switch to PLL */
		733	}
		734
		735	/* Set APB1 & APB2 prescaler*/
		736	LL_RCC_SetAPB1Prescaler(UTILS_ClkInitStruct->APB1CLKDivider);
		737	LL_RCC_SetAPB2Prescaler(UTILS_ClkInitStruct->APB2CLKDivider);
		738	}
		739
		740	/* Decreasing the number of wait states because of lower CPU frequency */
		741	#if defined (FLASH_ACR_LATENCY)
		742	if (sysclk_frequency_current > SYSCLK_Frequency)
		743	{
		744	/* Set FLASH latency to lowest latency */
		745	status = LL_SetFlashLatency(SYSCLK_Frequency);
		746	}
		747	#endif /* FLASH_ACR_LATENCY */
		748
		749	/* Update SystemCoreClock variable */
		750	if (status == SUCCESS)
		751	{
		752	LL_SetSystemCoreClock(__LL_RCC_CALC_HCLK_FREQ(SYSCLK_Frequency, UTILS_ClkInitStruct->AHBCLKDivider));
		753	}
		754
		755	return status;
		756	}
		757
		758	/**
		759	* @}
		760	*/
		761
		762	/**
		763	* @}
		764	*/
		765
		766	/**
		767	* @}
		768	*/
		769
		770	/********************** (C) COPYRIGHT STMicroelectronics *END OF FILE**/

Subversion Repositories canSerial

(root)/trunk/Drivers/STM32F1xx_HAL_Driver/Src/stm32f1xx_ll_utils.c – Rev 2