Subversion Repositories EDIS_Ignition

/**

  ******************************************************************************

  * @file    stm32f1xx_hal_gpio.c

  * @author  MCD Application Team

  * @brief   GPIO HAL module driver.

  *          This file provides firmware functions to manage the following

  *          functionalities of the General Purpose Input/Output (GPIO) peripheral:

  *           + Initialization and de-initialization functions

  *           + IO operation functions

  *

  ******************************************************************************

  * @attention

  *

  * Copyright (c) 2016 STMicroelectronics.

  * All rights reserved.

  *

  * This software is licensed under terms that can be found in the LICENSE file

  * in the root directory of this software component.

  * If no LICENSE file comes with this software, it is provided AS-IS.

  *

  ******************************************************************************

  @verbatim

  ==============================================================================

                    ##### GPIO Peripheral features #####

  ==============================================================================

  [..]

  Subject to the specific hardware characteristics of each I/O port listed in the datasheet, each

  port bit of the General Purpose IO (GPIO) Ports, can be individually configured by software

  in several modes:

  (+) Input mode

  (+) Analog mode

  (+) Output mode

  (+) Alternate function mode

  (+) External interrupt/event lines

  [..]

  During and just after reset, the alternate functions and external interrupt

  lines are not active and the I/O ports are configured in input floating mode.

  [..]

  All GPIO pins have weak internal pull-up and pull-down resistors, which can be

  activated or not.

  [..]

  In Output or Alternate mode, each IO can be configured on open-drain or push-pull

  type and the IO speed can be selected depending on the VDD value.

  [..]

  All ports have external interrupt/event capability. To use external interrupt

  lines, the port must be configured in input mode. All available GPIO pins are

  connected to the 16 external interrupt/event lines from EXTI0 to EXTI15.

  [..]

  The external interrupt/event controller consists of up to 20 edge detectors in connectivity

  line devices, or 19 edge detectors in other devices for generating event/interrupt requests.

  Each input line can be independently configured to select the type (event or interrupt) and

  the corresponding trigger event (rising or falling or both). Each line can also masked

  independently. A pending register maintains the status line of the interrupt requests

                     ##### How to use this driver #####

  ==============================================================================

 [..]

   (#) Enable the GPIO APB2 clock using the following function : __HAL_RCC_GPIOx_CLK_ENABLE().

   (#) Configure the GPIO pin(s) using HAL_GPIO_Init().

       (++) Configure the IO mode using "Mode" member from GPIO_InitTypeDef structure

       (++) Activate Pull-up, Pull-down resistor using "Pull" member from GPIO_InitTypeDef

            structure.

       (++) In case of Output or alternate function mode selection: the speed is

            configured through "Speed" member from GPIO_InitTypeDef structure

       (++) Analog mode is required when a pin is to be used as ADC channel

            or DAC output.

       (++) In case of external interrupt/event selection the "Mode" member from

            GPIO_InitTypeDef structure select the type (interrupt or event) and

            the corresponding trigger event (rising or falling or both).

   (#) In case of external interrupt/event mode selection, configure NVIC IRQ priority

       mapped to the EXTI line using HAL_NVIC_SetPriority() and enable it using

       HAL_NVIC_EnableIRQ().

   (#) To get the level of a pin configured in input mode use HAL_GPIO_ReadPin().

   (#) To set/reset the level of a pin configured in output mode use

       HAL_GPIO_WritePin()/HAL_GPIO_TogglePin().

   (#) To lock pin configuration until next reset use HAL_GPIO_LockPin().

   (#) During and just after reset, the alternate functions are not

       active and the GPIO pins are configured in input floating mode (except JTAG

       pins).

   (#) The LSE oscillator pins OSC32_IN and OSC32_OUT can be used as general purpose

       (PC14 and PC15, respectively) when the LSE oscillator is off. The LSE has

       priority over the GPIO function.

   (#) The HSE oscillator pins OSC_IN/OSC_OUT can be used as

       general purpose PD0 and PD1, respectively, when the HSE oscillator is off.

       The HSE has priority over the GPIO function.

  @endverbatim

  ******************************************************************************

  */

/* Includes ------------------------------------------------------------------*/

#include "stm32f1xx_hal.h"

/** @addtogroup STM32F1xx_HAL_Driver

  * @{

  */

/** @defgroup GPIO GPIO

  * @brief GPIO HAL module driver

  * @{

  */

#ifdef HAL_GPIO_MODULE_ENABLED

/* Private typedef -----------------------------------------------------------*/

/* Private define ------------------------------------------------------------*/

/** @addtogroup GPIO_Private_Constants GPIO Private Constants

  * @{

  */

#define GPIO_MODE             0x00000003u

#define EXTI_MODE             0x10000000u

#define GPIO_MODE_IT          0x00010000u

#define GPIO_MODE_EVT         0x00020000u

#define RISING_EDGE           0x00100000u

#define FALLING_EDGE          0x00200000u

#define GPIO_OUTPUT_TYPE      0x00000010u

#define GPIO_NUMBER           16u

/* Definitions for bit manipulation of CRL and CRH register */

#define  GPIO_CR_MODE_INPUT         0x00000000u /*!< 00: Input mode (reset state)  */

#define  GPIO_CR_CNF_ANALOG         0x00000000u /*!< 00: Analog mode  */

#define  GPIO_CR_CNF_INPUT_FLOATING 0x00000004u /*!< 01: Floating input (reset state)  */

#define  GPIO_CR_CNF_INPUT_PU_PD    0x00000008u /*!< 10: Input with pull-up / pull-down  */

#define  GPIO_CR_CNF_GP_OUTPUT_PP   0x00000000u /*!< 00: General purpose output push-pull  */

#define  GPIO_CR_CNF_GP_OUTPUT_OD   0x00000004u /*!< 01: General purpose output Open-drain  */

#define  GPIO_CR_CNF_AF_OUTPUT_PP   0x00000008u /*!< 10: Alternate function output Push-pull  */

#define  GPIO_CR_CNF_AF_OUTPUT_OD   0x0000000Cu /*!< 11: Alternate function output Open-drain  */

/**

  * @}

  */

/* Private macro -------------------------------------------------------------*/

/* Private variables ---------------------------------------------------------*/

/* Private function prototypes -----------------------------------------------*/

/* Private functions ---------------------------------------------------------*/

/* Exported functions --------------------------------------------------------*/

/** @defgroup GPIO_Exported_Functions GPIO Exported Functions

  * @{

  */

/** @defgroup GPIO_Exported_Functions_Group1 Initialization and de-initialization functions

 *  @brief    Initialization and Configuration functions

 *

@verbatim

 ===============================================================================

              ##### Initialization and de-initialization functions #####

 ===============================================================================

  [..]

    This section provides functions allowing to initialize and de-initialize the GPIOs

    to be ready for use.

@endverbatim

  * @{

  */

/**

  * @brief  Initializes the GPIOx peripheral according to the specified parameters in the GPIO_Init.

  * @param  GPIOx: where x can be (A..G depending on device used) to select the GPIO peripheral

  * @param  GPIO_Init: pointer to a GPIO_InitTypeDef structure that contains

  *         the configuration information for the specified GPIO peripheral.

  * @retval None

  */

void HAL_GPIO_Init(GPIO_TypeDef  *GPIOx, GPIO_InitTypeDef *GPIO_Init)

{

  uint32_t position = 0x00u;

  uint32_t ioposition;

  uint32_t iocurrent;

  uint32_t temp;

  uint32_t config = 0x00u;

  __IO uint32_t *configregister; /* Store the address of CRL or CRH register based on pin number */

  uint32_t registeroffset;       /* offset used during computation of CNF and MODE bits placement inside CRL or CRH register */

  /* Check the parameters */

  assert_param(IS_GPIO_ALL_INSTANCE(GPIOx));

  assert_param(IS_GPIO_PIN(GPIO_Init->Pin));

  assert_param(IS_GPIO_MODE(GPIO_Init->Mode));

  /* Configure the port pins */

  while (((GPIO_Init->Pin) >> position) != 0x00u)

  {

    /* Get the IO position */

    ioposition = (0x01uL << position);

    /* Get the current IO position */

    iocurrent = (uint32_t)(GPIO_Init->Pin) & ioposition;

    if (iocurrent == ioposition)

    {

      /* Check the Alternate function parameters */

      assert_param(IS_GPIO_AF_INSTANCE(GPIOx));

      /* Based on the required mode, filling config variable with MODEy[1:0] and CNFy[3:2] corresponding bits */

      switch (GPIO_Init->Mode)

      {

        /* If we are configuring the pin in OUTPUT push-pull mode */

        case GPIO_MODE_OUTPUT_PP:

          /* Check the GPIO speed parameter */

          assert_param(IS_GPIO_SPEED(GPIO_Init->Speed));

          config = GPIO_Init->Speed + GPIO_CR_CNF_GP_OUTPUT_PP;

          break;

        /* If we are configuring the pin in OUTPUT open-drain mode */

        case GPIO_MODE_OUTPUT_OD:

          /* Check the GPIO speed parameter */

          assert_param(IS_GPIO_SPEED(GPIO_Init->Speed));

          config = GPIO_Init->Speed + GPIO_CR_CNF_GP_OUTPUT_OD;

          break;

        /* If we are configuring the pin in ALTERNATE FUNCTION push-pull mode */

        case GPIO_MODE_AF_PP:

          /* Check the GPIO speed parameter */

          assert_param(IS_GPIO_SPEED(GPIO_Init->Speed));

          config = GPIO_Init->Speed + GPIO_CR_CNF_AF_OUTPUT_PP;

          break;

        /* If we are configuring the pin in ALTERNATE FUNCTION open-drain mode */

        case GPIO_MODE_AF_OD:

          /* Check the GPIO speed parameter */

          assert_param(IS_GPIO_SPEED(GPIO_Init->Speed));

          config = GPIO_Init->Speed + GPIO_CR_CNF_AF_OUTPUT_OD;

          break;

        /* If we are configuring the pin in INPUT (also applicable to EVENT and IT mode) */

        case GPIO_MODE_INPUT:

        case GPIO_MODE_IT_RISING:

        case GPIO_MODE_IT_FALLING:

        case GPIO_MODE_IT_RISING_FALLING:

        case GPIO_MODE_EVT_RISING:

        case GPIO_MODE_EVT_FALLING:

        case GPIO_MODE_EVT_RISING_FALLING:

          /* Check the GPIO pull parameter */

          assert_param(IS_GPIO_PULL(GPIO_Init->Pull));

          if (GPIO_Init->Pull == GPIO_NOPULL)

          {

            config = GPIO_CR_MODE_INPUT + GPIO_CR_CNF_INPUT_FLOATING;

          }

          else if (GPIO_Init->Pull == GPIO_PULLUP)

          {

            config = GPIO_CR_MODE_INPUT + GPIO_CR_CNF_INPUT_PU_PD;

            /* Set the corresponding ODR bit */

            GPIOx->BSRR = ioposition;

          }

          else /* GPIO_PULLDOWN */

          {

            config = GPIO_CR_MODE_INPUT + GPIO_CR_CNF_INPUT_PU_PD;

            /* Reset the corresponding ODR bit */

            GPIOx->BRR = ioposition;

          }

          break;

        /* If we are configuring the pin in INPUT analog mode */

        case GPIO_MODE_ANALOG:

          config = GPIO_CR_MODE_INPUT + GPIO_CR_CNF_ANALOG;

          break;

        /* Parameters are checked with assert_param */

        default:

          break;

      }

      /* Check if the current bit belongs to first half or last half of the pin count number

       in order to address CRH or CRL register*/

      configregister = (iocurrent < GPIO_PIN_8) ? &GPIOx->CRL     : &GPIOx->CRH;

      registeroffset = (iocurrent < GPIO_PIN_8) ? (position << 2u) : ((position - 8u) << 2u);

      /* Apply the new configuration of the pin to the register */

      MODIFY_REG((*configregister), ((GPIO_CRL_MODE0 | GPIO_CRL_CNF0) << registeroffset), (config << registeroffset));

      /*--------------------- EXTI Mode Configuration ------------------------*/

      /* Configure the External Interrupt or event for the current IO */

      if ((GPIO_Init->Mode & EXTI_MODE) == EXTI_MODE)

      {

        /* Enable AFIO Clock */

        __HAL_RCC_AFIO_CLK_ENABLE();

        temp = AFIO->EXTICR[position >> 2u];

        CLEAR_BIT(temp, (0x0Fu) << (4u * (position & 0x03u)));

        SET_BIT(temp, (GPIO_GET_INDEX(GPIOx)) << (4u * (position & 0x03u)));

        AFIO->EXTICR[position >> 2u] = temp;

        /* Enable or disable the rising trigger */

        if ((GPIO_Init->Mode & RISING_EDGE) == RISING_EDGE)

        {

          SET_BIT(EXTI->RTSR, iocurrent);

        }

        else

        {

          CLEAR_BIT(EXTI->RTSR, iocurrent);

        }

        /* Enable or disable the falling trigger */

        if ((GPIO_Init->Mode & FALLING_EDGE) == FALLING_EDGE)

        {

          SET_BIT(EXTI->FTSR, iocurrent);

        }

        else

        {

          CLEAR_BIT(EXTI->FTSR, iocurrent);

        }

        /* Configure the event mask */

        if ((GPIO_Init->Mode & GPIO_MODE_EVT) == GPIO_MODE_EVT)

        {

          SET_BIT(EXTI->EMR, iocurrent);

        }

        else

        {

          CLEAR_BIT(EXTI->EMR, iocurrent);

        }

        /* Configure the interrupt mask */

        if ((GPIO_Init->Mode & GPIO_MODE_IT) == GPIO_MODE_IT)

        {

          SET_BIT(EXTI->IMR, iocurrent);

        }

        else

        {

          CLEAR_BIT(EXTI->IMR, iocurrent);

        }

      }

    }

        position++;

  }

}

/**

  * @brief  De-initializes the GPIOx peripheral registers to their default reset values.

  * @param  GPIOx: where x can be (A..G depending on device used) to select the GPIO peripheral

  * @param  GPIO_Pin: specifies the port bit to be written.

  *         This parameter can be one of GPIO_PIN_x where x can be (0..15).

  * @retval None

  */

void HAL_GPIO_DeInit(GPIO_TypeDef  *GPIOx, uint32_t GPIO_Pin)

{

  uint32_t position = 0x00u;

  uint32_t iocurrent;

  uint32_t tmp;

  __IO uint32_t *configregister; /* Store the address of CRL or CRH register based on pin number */

  uint32_t registeroffset;

  /* Check the parameters */

  assert_param(IS_GPIO_ALL_INSTANCE(GPIOx));

  assert_param(IS_GPIO_PIN(GPIO_Pin));

  /* Configure the port pins */

  while ((GPIO_Pin >> position) != 0u)

  {

    /* Get current io position */

    iocurrent = (GPIO_Pin) & (1uL << position);

    if (iocurrent)

    {

      /*------------------------- EXTI Mode Configuration --------------------*/

      /* Clear the External Interrupt or Event for the current IO */

      tmp = AFIO->EXTICR[position >> 2u];

      tmp &= 0x0FuL << (4u * (position & 0x03u));

      if (tmp == (GPIO_GET_INDEX(GPIOx) << (4u * (position & 0x03u))))

      {

        /* Clear EXTI line configuration */

        CLEAR_BIT(EXTI->IMR, (uint32_t)iocurrent);

        CLEAR_BIT(EXTI->EMR, (uint32_t)iocurrent);

        /* Clear Rising Falling edge configuration */

        CLEAR_BIT(EXTI->FTSR, (uint32_t)iocurrent);

        CLEAR_BIT(EXTI->RTSR, (uint32_t)iocurrent);

        tmp = 0x0FuL << (4u * (position & 0x03u));

        CLEAR_BIT(AFIO->EXTICR[position >> 2u], tmp);

      }

      /*------------------------- GPIO Mode Configuration --------------------*/

      /* Check if the current bit belongs to first half or last half of the pin count number

       in order to address CRH or CRL register */

      configregister = (iocurrent < GPIO_PIN_8) ? &GPIOx->CRL     : &GPIOx->CRH;

      registeroffset = (iocurrent < GPIO_PIN_8) ? (position << 2u) : ((position - 8u) << 2u);

      /* CRL/CRH default value is floating input(0x04) shifted to correct position */

      MODIFY_REG(*configregister, ((GPIO_CRL_MODE0 | GPIO_CRL_CNF0) << registeroffset), GPIO_CRL_CNF0_0 << registeroffset);

      /* ODR default value is 0 */

      CLEAR_BIT(GPIOx->ODR, iocurrent);

    }

    position++;

  }

}

/**

  * @}

  */

/** @defgroup GPIO_Exported_Functions_Group2 IO operation functions

 *  @brief   GPIO Read and Write

 *

@verbatim

 ===============================================================================

                       ##### IO operation functions #####

 ===============================================================================

  [..]

    This subsection provides a set of functions allowing to manage the GPIOs.

@endverbatim

  * @{

  */

/**

  * @brief  Reads the specified input port pin.

  * @param  GPIOx: where x can be (A..G depending on device used) to select the GPIO peripheral

  * @param  GPIO_Pin: specifies the port bit to read.

  *         This parameter can be GPIO_PIN_x where x can be (0..15).

  * @retval The input port pin value.

  */

GPIO_PinState HAL_GPIO_ReadPin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin)

{

  GPIO_PinState bitstatus;

  /* Check the parameters */

  assert_param(IS_GPIO_PIN(GPIO_Pin));

  if ((GPIOx->IDR & GPIO_Pin) != (uint32_t)GPIO_PIN_RESET)

  {

    bitstatus = GPIO_PIN_SET;

  }

  else

  {

    bitstatus = GPIO_PIN_RESET;

  }

  return bitstatus;

}

/**

  * @brief  Sets or clears the selected data port bit.

  *

  * @note   This function uses GPIOx_BSRR register to allow atomic read/modify

  *         accesses. In this way, there is no risk of an IRQ occurring between

  *         the read and the modify access.

  *

  * @param  GPIOx: where x can be (A..G depending on device used) to select the GPIO peripheral

  * @param  GPIO_Pin: specifies the port bit to be written.

  *          This parameter can be one of GPIO_PIN_x where x can be (0..15).

  * @param  PinState: specifies the value to be written to the selected bit.

  *          This parameter can be one of the GPIO_PinState enum values:

  *            @arg GPIO_PIN_RESET: to clear the port pin

  *            @arg GPIO_PIN_SET: to set the port pin

  * @retval None

  */

void HAL_GPIO_WritePin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin, GPIO_PinState PinState)

{

  /* Check the parameters */

  assert_param(IS_GPIO_PIN(GPIO_Pin));

  assert_param(IS_GPIO_PIN_ACTION(PinState));

  if (PinState != GPIO_PIN_RESET)

  {

    GPIOx->BSRR = GPIO_Pin;

  }

  else

  {

    GPIOx->BSRR = (uint32_t)GPIO_Pin << 16u;

  }

}

/**

  * @brief  Toggles the specified GPIO pin

  * @param  GPIOx: where x can be (A..G depending on device used) to select the GPIO peripheral

  * @param  GPIO_Pin: Specifies the pins to be toggled.

  * @retval None

  */

void HAL_GPIO_TogglePin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin)

{

  uint32_t odr;

  /* Check the parameters */

  assert_param(IS_GPIO_PIN(GPIO_Pin));

  /* get current Output Data Register value */

  odr = GPIOx->ODR;

  /* Set selected pins that were at low level, and reset ones that were high */

  GPIOx->BSRR = ((odr & GPIO_Pin) << GPIO_NUMBER) | (~odr & GPIO_Pin);

}

/**

* @brief  Locks GPIO Pins configuration registers.

* @note   The locking mechanism allows the IO configuration to be frozen. When the LOCK sequence

*         has been applied on a port bit, it is no longer possible to modify the value of the port bit until

*         the next reset.

* @param  GPIOx: where x can be (A..G depending on device used) to select the GPIO peripheral

* @param  GPIO_Pin: specifies the port bit to be locked.

*         This parameter can be any combination of GPIO_Pin_x where x can be (0..15).

* @retval None

*/

HAL_StatusTypeDef HAL_GPIO_LockPin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin)

{

  __IO uint32_t tmp = GPIO_LCKR_LCKK;

  /* Check the parameters */

  assert_param(IS_GPIO_LOCK_INSTANCE(GPIOx));

  assert_param(IS_GPIO_PIN(GPIO_Pin));

  /* Apply lock key write sequence */

  SET_BIT(tmp, GPIO_Pin);

  /* Set LCKx bit(s): LCKK='1' + LCK[15-0] */

  GPIOx->LCKR = tmp;

  /* Reset LCKx bit(s): LCKK='0' + LCK[15-0] */

  GPIOx->LCKR = GPIO_Pin;

  /* Set LCKx bit(s): LCKK='1' + LCK[15-0] */

  GPIOx->LCKR = tmp;

  /* Read LCKK register. This read is mandatory to complete key lock sequence */

  tmp = GPIOx->LCKR;

  /* read again in order to confirm lock is active */

  if ((uint32_t)(GPIOx->LCKR & GPIO_LCKR_LCKK))

  {

    return HAL_OK;

  }

  else

  {

    return HAL_ERROR;

  }

}

/**

  * @brief  This function handles EXTI interrupt request.

  * @param  GPIO_Pin: Specifies the pins connected EXTI line

  * @retval None

  */

void HAL_GPIO_EXTI_IRQHandler(uint16_t GPIO_Pin)

{

  /* EXTI line interrupt detected */

  if (__HAL_GPIO_EXTI_GET_IT(GPIO_Pin) != 0x00u)

  {

    __HAL_GPIO_EXTI_CLEAR_IT(GPIO_Pin);

    HAL_GPIO_EXTI_Callback(GPIO_Pin);

  }

}

/**

  * @brief  EXTI line detection callbacks.

  * @param  GPIO_Pin: Specifies the pins connected EXTI line

  * @retval None

  */

__weak void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin)

{

  /* Prevent unused argument(s) compilation warning */

  UNUSED(GPIO_Pin);

  /* NOTE: This function Should not be modified, when the callback is needed,

           the HAL_GPIO_EXTI_Callback could be implemented in the user file

   */

}

/**

  * @}

  */

/**

  * @}

  */

#endif /* HAL_GPIO_MODULE_ENABLED */

/**

  * @}

  */

/**

  * @}

  */