WebSVN – LedShow – Blame – /trunk/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_ll_i2c.h

Rev	Author	Line No.	Line
2	mjames	1	/**
		2	******************************************************************************
		3	* @file stm32f1xx_ll_i2c.h
		4	* @author MCD Application Team
		5	* @brief Header file of I2C LL module.
		6	******************************************************************************
		7	* @attention
		8	*
9	mjames	9	* <h2><center>© Copyright (c) 2016 STMicroelectronics.
		10	* All rights reserved.</center></h2>
2	mjames	11	*
9	mjames	12	* This software component is licensed by ST under BSD 3-Clause license,
		13	* the "License"; You may not use this file except in compliance with the
		14	* License. You may obtain a copy of the License at:
		15	* opensource.org/licenses/BSD-3-Clause
2	mjames	16	*
		17	******************************************************************************
		18	*/
		19
		20	/* Define to prevent recursive inclusion -------------------------------------*/
		21	#ifndef __STM32F1xx_LL_I2C_H
		22	#define __STM32F1xx_LL_I2C_H
		23
		24	#ifdef __cplusplus
		25	extern "C" {
		26	#endif
		27
		28	/* Includes ------------------------------------------------------------------*/
		29	#include "stm32f1xx.h"
		30
		31	/** @addtogroup STM32F1xx_LL_Driver
		32	* @{
		33	*/
		34
		35	#if defined (I2C1) \|\| defined (I2C2)
		36
		37	/** @defgroup I2C_LL I2C
		38	* @{
		39	*/
		40
		41	/* Private types -------------------------------------------------------------*/
		42	/* Private variables ---------------------------------------------------------*/
		43
		44	/* Private constants ---------------------------------------------------------*/
		45	/** @defgroup I2C_LL_Private_Constants I2C Private Constants
		46	* @{
		47	*/
		48
		49	/* Defines used to perform compute and check in the macros */
		50	#define LL_I2C_MAX_SPEED_STANDARD 100000U
		51	#define LL_I2C_MAX_SPEED_FAST 400000U
		52	/**
		53	* @}
		54	*/
		55
		56	/* Private macros ------------------------------------------------------------*/
		57	#if defined(USE_FULL_LL_DRIVER)
		58	/** @defgroup I2C_LL_Private_Macros I2C Private Macros
		59	* @{
		60	*/
		61	/**
		62	* @}
		63	*/
		64	#endif /USE_FULL_LL_DRIVER/
		65
		66	/* Exported types ------------------------------------------------------------*/
		67	#if defined(USE_FULL_LL_DRIVER)
		68	/** @defgroup I2C_LL_ES_INIT I2C Exported Init structure
		69	* @{
		70	*/
		71	typedef struct
		72	{
		73	uint32_t PeripheralMode; /*!< Specifies the peripheral mode.
		74	This parameter can be a value of @ref I2C_LL_EC_PERIPHERAL_MODE
		75
		76	This feature can be modified afterwards using unitary function @ref LL_I2C_SetMode(). */
		77
		78	uint32_t ClockSpeed; /*!< Specifies the clock frequency.
		79	This parameter must be set to a value lower than 400kHz (in Hz)
		80
		81	This feature can be modified afterwards using unitary function @ref LL_I2C_SetClockPeriod()
		82	or @ref LL_I2C_SetDutyCycle() or @ref LL_I2C_SetClockSpeedMode() or @ref LL_I2C_ConfigSpeed(). */
		83
		84	uint32_t DutyCycle; /*!< Specifies the I2C fast mode duty cycle.
		85	This parameter can be a value of @ref I2C_LL_EC_DUTYCYCLE
		86
		87	This feature can be modified afterwards using unitary function @ref LL_I2C_SetDutyCycle(). */
		88
		89	uint32_t OwnAddress1; /*!< Specifies the device own address 1.
		90	This parameter must be a value between Min_Data = 0x00 and Max_Data = 0x3FF
		91
		92	This feature can be modified afterwards using unitary function @ref LL_I2C_SetOwnAddress1(). */
		93
		94	uint32_t TypeAcknowledge; /*!< Specifies the ACKnowledge or Non ACKnowledge condition after the address receive match code or next received byte.
		95	This parameter can be a value of @ref I2C_LL_EC_I2C_ACKNOWLEDGE
		96
		97	This feature can be modified afterwards using unitary function @ref LL_I2C_AcknowledgeNextData(). */
		98
		99	uint32_t OwnAddrSize; /*!< Specifies the device own address 1 size (7-bit or 10-bit).
		100	This parameter can be a value of @ref I2C_LL_EC_OWNADDRESS1
		101
		102	This feature can be modified afterwards using unitary function @ref LL_I2C_SetOwnAddress1(). */
		103	} LL_I2C_InitTypeDef;
		104	/**
		105	* @}
		106	*/
		107	#endif /USE_FULL_LL_DRIVER/
		108
		109	/* Exported constants --------------------------------------------------------*/
		110	/** @defgroup I2C_LL_Exported_Constants I2C Exported Constants
		111	* @{
		112	*/
		113
		114	/** @defgroup I2C_LL_EC_GET_FLAG Get Flags Defines
		115	* @brief Flags defines which can be used with LL_I2C_ReadReg function
		116	* @{
		117	*/
		118	#define LL_I2C_SR1_SB I2C_SR1_SB /!< Start Bit (master mode) /
		119	#define LL_I2C_SR1_ADDR I2C_SR1_ADDR /*!< Address sent (master mode) or
		120	Address matched flag (slave mode) */
		121	#define LL_I2C_SR1_BTF I2C_SR1_BTF /!< Byte Transfer Finished flag /
		122	#define LL_I2C_SR1_ADD10 I2C_SR1_ADD10 /!< 10-bit header sent (master mode) /
		123	#define LL_I2C_SR1_STOPF I2C_SR1_STOPF /!< Stop detection flag (slave mode) /
		124	#define LL_I2C_SR1_RXNE I2C_SR1_RXNE /!< Data register not empty (receivers) /
		125	#define LL_I2C_SR1_TXE I2C_SR1_TXE /!< Data register empty (transmitters) /
		126	#define LL_I2C_SR1_BERR I2C_SR1_BERR /!< Bus error /
		127	#define LL_I2C_SR1_ARLO I2C_SR1_ARLO /!< Arbitration lost /
		128	#define LL_I2C_SR1_AF I2C_SR1_AF /!< Acknowledge failure flag /
		129	#define LL_I2C_SR1_OVR I2C_SR1_OVR /!< Overrun/Underrun /
		130	#define LL_I2C_SR1_PECERR I2C_ISR_PECERR /!< PEC Error in reception (SMBus mode) /
		131	#define LL_I2C_SR1_TIMEOUT I2C_ISR_TIMEOUT /!< Timeout detection flag (SMBus mode) /
		132	#define LL_I2C_SR1_SMALERT I2C_ISR_SMALERT /!< SMBus alert (SMBus mode) /
		133	#define LL_I2C_SR2_MSL I2C_SR2_MSL /!< Master/Slave flag /
		134	#define LL_I2C_SR2_BUSY I2C_SR2_BUSY /!< Bus busy flag /
		135	#define LL_I2C_SR2_TRA I2C_SR2_TRA /!< Transmitter/receiver direction /
		136	#define LL_I2C_SR2_GENCALL I2C_SR2_GENCALL /!< General call address (Slave mode) /
		137	#define LL_I2C_SR2_SMBDEFAULT I2C_SR2_SMBDEFAULT /!< SMBus Device default address (Slave mode) /
		138	#define LL_I2C_SR2_SMBHOST I2C_SR2_SMBHOST /!< SMBus Host address (Slave mode) /
		139	#define LL_I2C_SR2_DUALF I2C_SR2_DUALF /!< Dual flag (Slave mode) /
		140	/**
		141	* @}
		142	*/
		143
		144	/** @defgroup I2C_LL_EC_IT IT Defines
		145	* @brief IT defines which can be used with LL_I2C_ReadReg and LL_I2C_WriteReg functions
		146	* @{
		147	*/
		148	#define LL_I2C_CR2_ITEVTEN I2C_CR2_ITEVTEN /!< Events interrupts enable /
		149	#define LL_I2C_CR2_ITBUFEN I2C_CR2_ITBUFEN /!< Buffer interrupts enable /
		150	#define LL_I2C_CR2_ITERREN I2C_CR2_ITERREN /!< Error interrupts enable /
		151	/**
		152	* @}
		153	*/
		154
		155	/** @defgroup I2C_LL_EC_OWNADDRESS1 Own Address 1 Length
		156	* @{
		157	*/
		158	#define LL_I2C_OWNADDRESS1_7BIT 0x00004000U /!< Own address 1 is a 7-bit address. /
		159	#define LL_I2C_OWNADDRESS1_10BIT (uint32_t)(I2C_OAR1_ADDMODE \| 0x00004000U) /!< Own address 1 is a 10-bit address. /
		160	/**
		161	* @}
		162	*/
		163
		164	/** @defgroup I2C_LL_EC_DUTYCYCLE Fast Mode Duty Cycle
		165	* @{
		166	*/
		167	#define LL_I2C_DUTYCYCLE_2 0x00000000U /!< I2C fast mode Tlow/Thigh = 2 /
		168	#define LL_I2C_DUTYCYCLE_16_9 I2C_CCR_DUTY /!< I2C fast mode Tlow/Thigh = 16/9 /
		169	/**
		170	* @}
		171	*/
		172
		173	/** @defgroup I2C_LL_EC_CLOCK_SPEED_MODE Master Clock Speed Mode
		174	* @{
		175	*/
		176	#define LL_I2C_CLOCK_SPEED_STANDARD_MODE 0x00000000U /!< Master clock speed range is standard mode /
		177	#define LL_I2C_CLOCK_SPEED_FAST_MODE I2C_CCR_FS /!< Master clock speed range is fast mode /
		178	/**
		179	* @}
		180	*/
		181
		182	/** @defgroup I2C_LL_EC_PERIPHERAL_MODE Peripheral Mode
		183	* @{
		184	*/
		185	#define LL_I2C_MODE_I2C 0x00000000U /!< I2C Master or Slave mode /
		186	#define LL_I2C_MODE_SMBUS_HOST (uint32_t)(I2C_CR1_SMBUS \| I2C_CR1_SMBTYPE \| I2C_CR1_ENARP) /!< SMBus Host address acknowledge /
		187	#define LL_I2C_MODE_SMBUS_DEVICE I2C_CR1_SMBUS /!< SMBus Device default mode (Default address not acknowledge) /
		188	#define LL_I2C_MODE_SMBUS_DEVICE_ARP (uint32_t)(I2C_CR1_SMBUS \| I2C_CR1_ENARP) /!< SMBus Device Default address acknowledge /
		189	/**
		190	* @}
		191	*/
		192
		193	/** @defgroup I2C_LL_EC_I2C_ACKNOWLEDGE Acknowledge Generation
		194	* @{
		195	*/
		196	#define LL_I2C_ACK I2C_CR1_ACK /!< ACK is sent after current received byte. /
		197	#define LL_I2C_NACK 0x00000000U /!< NACK is sent after current received byte./
		198	/**
		199	* @}
		200	*/
		201
		202	/** @defgroup I2C_LL_EC_DIRECTION Read Write Direction
		203	* @{
		204	*/
		205	#define LL_I2C_DIRECTION_WRITE I2C_SR2_TRA /!< Bus is in write transfer /
		206	#define LL_I2C_DIRECTION_READ 0x00000000U /!< Bus is in read transfer /
		207	/**
		208	* @}
		209	*/
		210
		211	/**
		212	* @}
		213	*/
		214
		215	/* Exported macro ------------------------------------------------------------*/
		216	/** @defgroup I2C_LL_Exported_Macros I2C Exported Macros
		217	* @{
		218	*/
		219
		220	/** @defgroup I2C_LL_EM_WRITE_READ Common Write and read registers Macros
		221	* @{
		222	*/
		223
		224	/**
		225	* @brief Write a value in I2C register
		226	* @param __INSTANCE__ I2C Instance
		227	* @param __REG__ Register to be written
		228	* @param __VALUE__ Value to be written in the register
		229	* @retval None
		230	*/
		231	#define LL_I2C_WriteReg(__INSTANCE__, __REG__, __VALUE__) WRITE_REG(__INSTANCE__->__REG__, (__VALUE__))
		232
		233	/**
		234	* @brief Read a value in I2C register
		235	* @param __INSTANCE__ I2C Instance
		236	* @param __REG__ Register to be read
		237	* @retval Register value
		238	*/
		239	#define LL_I2C_ReadReg(__INSTANCE__, __REG__) READ_REG(__INSTANCE__->__REG__)
		240	/**
		241	* @}
		242	*/
		243
		244	/** @defgroup I2C_LL_EM_Exported_Macros_Helper Exported_Macros_Helper
		245	* @{
		246	*/
		247
		248	/**
		249	* @brief Convert Peripheral Clock Frequency in Mhz.
		250	* @param __PCLK__ This parameter must be a value of peripheral clock (in Hz).
		251	* @retval Value of peripheral clock (in Mhz)
		252	*/
		253	#define __LL_I2C_FREQ_HZ_TO_MHZ(__PCLK__) (uint32_t)((__PCLK__)/1000000U)
		254
		255	/**
		256	* @brief Convert Peripheral Clock Frequency in Hz.
		257	* @param __PCLK__ This parameter must be a value of peripheral clock (in Mhz).
		258	* @retval Value of peripheral clock (in Hz)
		259	*/
		260	#define __LL_I2C_FREQ_MHZ_TO_HZ(__PCLK__) (uint32_t)((__PCLK__)*1000000U)
		261
		262	/**
		263	* @brief Compute I2C Clock rising time.
		264	* @param __FREQRANGE__ This parameter must be a value of peripheral clock (in Mhz).
		265	* @param __SPEED__ This parameter must be a value lower than 400kHz (in Hz).
		266	* @retval Value between Min_Data=0x02 and Max_Data=0x3F
		267	*/
		268	#define __LL_I2C_RISE_TIME(__FREQRANGE__, __SPEED__) (uint32_t)(((__SPEED__) <= LL_I2C_MAX_SPEED_STANDARD) ? ((__FREQRANGE__) + 1U) : ((((__FREQRANGE__) * 300U) / 1000U) + 1U))
		269
		270	/**
		271	* @brief Compute Speed clock range to a Clock Control Register (I2C_CCR_CCR) value.
		272	* @param __PCLK__ This parameter must be a value of peripheral clock (in Hz).
		273	* @param __SPEED__ This parameter must be a value lower than 400kHz (in Hz).
		274	* @param __DUTYCYCLE__ This parameter can be one of the following values:
		275	* @arg @ref LL_I2C_DUTYCYCLE_2
		276	* @arg @ref LL_I2C_DUTYCYCLE_16_9
		277	* @retval Value between Min_Data=0x004 and Max_Data=0xFFF, except in FAST DUTY mode where Min_Data=0x001.
		278	*/
		279	#define __LL_I2C_SPEED_TO_CCR(__PCLK__, __SPEED__, __DUTYCYCLE__) (uint32_t)(((__SPEED__) <= LL_I2C_MAX_SPEED_STANDARD)? \
		280	(__LL_I2C_SPEED_STANDARD_TO_CCR((__PCLK__), (__SPEED__))) : \
		281	(__LL_I2C_SPEED_FAST_TO_CCR((__PCLK__), (__SPEED__), (__DUTYCYCLE__))))
		282
		283	/**
		284	* @brief Compute Speed Standard clock range to a Clock Control Register (I2C_CCR_CCR) value.
		285	* @param __PCLK__ This parameter must be a value of peripheral clock (in Hz).
		286	* @param __SPEED__ This parameter must be a value lower than 100kHz (in Hz).
		287	* @retval Value between Min_Data=0x004 and Max_Data=0xFFF.
		288	*/
		289	#define __LL_I2C_SPEED_STANDARD_TO_CCR(__PCLK__, __SPEED__) (uint32_t)(((((__PCLK__)/((__SPEED__) << 1U)) & I2C_CCR_CCR) < 4U)? 4U:((__PCLK__) / ((__SPEED__) << 1U)))
		290
		291	/**
		292	* @brief Compute Speed Fast clock range to a Clock Control Register (I2C_CCR_CCR) value.
		293	* @param __PCLK__ This parameter must be a value of peripheral clock (in Hz).
		294	* @param __SPEED__ This parameter must be a value between Min_Data=100Khz and Max_Data=400Khz (in Hz).
		295	* @param __DUTYCYCLE__ This parameter can be one of the following values:
		296	* @arg @ref LL_I2C_DUTYCYCLE_2
		297	* @arg @ref LL_I2C_DUTYCYCLE_16_9
		298	* @retval Value between Min_Data=0x001 and Max_Data=0xFFF
		299	*/
		300	#define __LL_I2C_SPEED_FAST_TO_CCR(__PCLK__, __SPEED__, __DUTYCYCLE__) (uint32_t)(((__DUTYCYCLE__) == LL_I2C_DUTYCYCLE_2)? \
		301	(((((__PCLK__) / ((__SPEED__) * 3U)) & I2C_CCR_CCR) == 0U)? 1U:((__PCLK__) / ((__SPEED__) * 3U))) : \
		302	(((((__PCLK__) / ((__SPEED__) * 25U)) & I2C_CCR_CCR) == 0U)? 1U:((__PCLK__) / ((__SPEED__) * 25U))))
		303
		304	/**
		305	* @brief Get the Least significant bits of a 10-Bits address.
		306	* @param __ADDRESS__ This parameter must be a value of a 10-Bits slave address.
		307	* @retval Value between Min_Data=0x00 and Max_Data=0xFF
		308	*/
		309	#define __LL_I2C_10BIT_ADDRESS(__ADDRESS__) ((uint8_t)((uint16_t)((__ADDRESS__) & (uint16_t)(0x00FF))))
		310
		311	/**
		312	* @brief Convert a 10-Bits address to a 10-Bits header with Write direction.
		313	* @param __ADDRESS__ This parameter must be a value of a 10-Bits slave address.
		314	* @retval Value between Min_Data=0xF0 and Max_Data=0xF6
		315	*/
		316	#define __LL_I2C_10BIT_HEADER_WRITE(__ADDRESS__) ((uint8_t)((uint16_t)((uint16_t)(((uint16_t)((__ADDRESS__) & (uint16_t)(0x0300))) >> 7) \| (uint16_t)(0xF0))))
		317
		318	/**
		319	* @brief Convert a 10-Bits address to a 10-Bits header with Read direction.
		320	* @param __ADDRESS__ This parameter must be a value of a 10-Bits slave address.
		321	* @retval Value between Min_Data=0xF1 and Max_Data=0xF7
		322	*/
		323	#define __LL_I2C_10BIT_HEADER_READ(__ADDRESS__) ((uint8_t)((uint16_t)((uint16_t)(((uint16_t)((__ADDRESS__) & (uint16_t)(0x0300))) >> 7) \| (uint16_t)(0xF1))))
		324
		325	/**
		326	* @}
		327	*/
		328
		329	/**
		330	* @}
		331	*/
		332
		333	/* Exported functions --------------------------------------------------------*/
		334
		335	/** @defgroup I2C_LL_Exported_Functions I2C Exported Functions
		336	* @{
		337	*/
		338
		339	/** @defgroup I2C_LL_EF_Configuration Configuration
		340	* @{
		341	*/
		342
		343	/**
		344	* @brief Enable I2C peripheral (PE = 1).
		345	* @rmtoll CR1 PE LL_I2C_Enable
		346	* @param I2Cx I2C Instance.
		347	* @retval None
		348	*/
		349	__STATIC_INLINE void LL_I2C_Enable(I2C_TypeDef *I2Cx)
		350	{
		351	SET_BIT(I2Cx->CR1, I2C_CR1_PE);
		352	}
		353
		354	/**
		355	* @brief Disable I2C peripheral (PE = 0).
		356	* @rmtoll CR1 PE LL_I2C_Disable
		357	* @param I2Cx I2C Instance.
		358	* @retval None
		359	*/
		360	__STATIC_INLINE void LL_I2C_Disable(I2C_TypeDef *I2Cx)
		361	{
		362	CLEAR_BIT(I2Cx->CR1, I2C_CR1_PE);
		363	}
		364
		365	/**
		366	* @brief Check if the I2C peripheral is enabled or disabled.
		367	* @rmtoll CR1 PE LL_I2C_IsEnabled
		368	* @param I2Cx I2C Instance.
		369	* @retval State of bit (1 or 0).
		370	*/
		371	__STATIC_INLINE uint32_t LL_I2C_IsEnabled(I2C_TypeDef *I2Cx)
		372	{
		373	return (READ_BIT(I2Cx->CR1, I2C_CR1_PE) == (I2C_CR1_PE));
		374	}
		375
		376
		377	/**
		378	* @brief Enable DMA transmission requests.
		379	* @rmtoll CR2 DMAEN LL_I2C_EnableDMAReq_TX
		380	* @param I2Cx I2C Instance.
		381	* @retval None
		382	*/
		383	__STATIC_INLINE void LL_I2C_EnableDMAReq_TX(I2C_TypeDef *I2Cx)
		384	{
		385	SET_BIT(I2Cx->CR2, I2C_CR2_DMAEN);
		386	}
		387
		388	/**
		389	* @brief Disable DMA transmission requests.
		390	* @rmtoll CR2 DMAEN LL_I2C_DisableDMAReq_TX
		391	* @param I2Cx I2C Instance.
		392	* @retval None
		393	*/
		394	__STATIC_INLINE void LL_I2C_DisableDMAReq_TX(I2C_TypeDef *I2Cx)
		395	{
		396	CLEAR_BIT(I2Cx->CR2, I2C_CR2_DMAEN);
		397	}
		398
		399	/**
		400	* @brief Check if DMA transmission requests are enabled or disabled.
		401	* @rmtoll CR2 DMAEN LL_I2C_IsEnabledDMAReq_TX
		402	* @param I2Cx I2C Instance.
		403	* @retval State of bit (1 or 0).
		404	*/
		405	__STATIC_INLINE uint32_t LL_I2C_IsEnabledDMAReq_TX(I2C_TypeDef *I2Cx)
		406	{
		407	return (READ_BIT(I2Cx->CR2, I2C_CR2_DMAEN) == (I2C_CR2_DMAEN));
		408	}
		409
		410	/**
		411	* @brief Enable DMA reception requests.
		412	* @rmtoll CR2 DMAEN LL_I2C_EnableDMAReq_RX
		413	* @param I2Cx I2C Instance.
		414	* @retval None
		415	*/
		416	__STATIC_INLINE void LL_I2C_EnableDMAReq_RX(I2C_TypeDef *I2Cx)
		417	{
		418	SET_BIT(I2Cx->CR2, I2C_CR2_DMAEN);
		419	}
		420
		421	/**
		422	* @brief Disable DMA reception requests.
		423	* @rmtoll CR2 DMAEN LL_I2C_DisableDMAReq_RX
		424	* @param I2Cx I2C Instance.
		425	* @retval None
		426	*/
		427	__STATIC_INLINE void LL_I2C_DisableDMAReq_RX(I2C_TypeDef *I2Cx)
		428	{
		429	CLEAR_BIT(I2Cx->CR2, I2C_CR2_DMAEN);
		430	}
		431
		432	/**
		433	* @brief Check if DMA reception requests are enabled or disabled.
		434	* @rmtoll CR2 DMAEN LL_I2C_IsEnabledDMAReq_RX
		435	* @param I2Cx I2C Instance.
		436	* @retval State of bit (1 or 0).
		437	*/
		438	__STATIC_INLINE uint32_t LL_I2C_IsEnabledDMAReq_RX(I2C_TypeDef *I2Cx)
		439	{
		440	return (READ_BIT(I2Cx->CR2, I2C_CR2_DMAEN) == (I2C_CR2_DMAEN));
		441	}
		442
		443	/**
		444	* @brief Get the data register address used for DMA transfer.
		445	* @rmtoll DR DR LL_I2C_DMA_GetRegAddr
		446	* @param I2Cx I2C Instance.
		447	* @retval Address of data register
		448	*/
		449	__STATIC_INLINE uint32_t LL_I2C_DMA_GetRegAddr(I2C_TypeDef *I2Cx)
		450	{
		451	return (uint32_t) & (I2Cx->DR);
		452	}
		453
		454	/**
		455	* @brief Enable Clock stretching.
		456	* @note This bit can only be programmed when the I2C is disabled (PE = 0).
		457	* @rmtoll CR1 NOSTRETCH LL_I2C_EnableClockStretching
		458	* @param I2Cx I2C Instance.
		459	* @retval None
		460	*/
		461	__STATIC_INLINE void LL_I2C_EnableClockStretching(I2C_TypeDef *I2Cx)
		462	{
		463	CLEAR_BIT(I2Cx->CR1, I2C_CR1_NOSTRETCH);
		464	}
		465
		466	/**
		467	* @brief Disable Clock stretching.
		468	* @note This bit can only be programmed when the I2C is disabled (PE = 0).
		469	* @rmtoll CR1 NOSTRETCH LL_I2C_DisableClockStretching
		470	* @param I2Cx I2C Instance.
		471	* @retval None
		472	*/
		473	__STATIC_INLINE void LL_I2C_DisableClockStretching(I2C_TypeDef *I2Cx)
		474	{
		475	SET_BIT(I2Cx->CR1, I2C_CR1_NOSTRETCH);
		476	}
		477
		478	/**
		479	* @brief Check if Clock stretching is enabled or disabled.
		480	* @rmtoll CR1 NOSTRETCH LL_I2C_IsEnabledClockStretching
		481	* @param I2Cx I2C Instance.
		482	* @retval State of bit (1 or 0).
		483	*/
		484	__STATIC_INLINE uint32_t LL_I2C_IsEnabledClockStretching(I2C_TypeDef *I2Cx)
		485	{
		486	return (READ_BIT(I2Cx->CR1, I2C_CR1_NOSTRETCH) != (I2C_CR1_NOSTRETCH));
		487	}
		488
		489	/**
		490	* @brief Enable General Call.
		491	* @note When enabled the Address 0x00 is ACKed.
		492	* @rmtoll CR1 ENGC LL_I2C_EnableGeneralCall
		493	* @param I2Cx I2C Instance.
		494	* @retval None
		495	*/
		496	__STATIC_INLINE void LL_I2C_EnableGeneralCall(I2C_TypeDef *I2Cx)
		497	{
		498	SET_BIT(I2Cx->CR1, I2C_CR1_ENGC);
		499	}
		500
		501	/**
		502	* @brief Disable General Call.
		503	* @note When disabled the Address 0x00 is NACKed.
		504	* @rmtoll CR1 ENGC LL_I2C_DisableGeneralCall
		505	* @param I2Cx I2C Instance.
		506	* @retval None
		507	*/
		508	__STATIC_INLINE void LL_I2C_DisableGeneralCall(I2C_TypeDef *I2Cx)
		509	{
		510	CLEAR_BIT(I2Cx->CR1, I2C_CR1_ENGC);
		511	}
		512
		513	/**
		514	* @brief Check if General Call is enabled or disabled.
		515	* @rmtoll CR1 ENGC LL_I2C_IsEnabledGeneralCall
		516	* @param I2Cx I2C Instance.
		517	* @retval State of bit (1 or 0).
		518	*/
		519	__STATIC_INLINE uint32_t LL_I2C_IsEnabledGeneralCall(I2C_TypeDef *I2Cx)
		520	{
		521	return (READ_BIT(I2Cx->CR1, I2C_CR1_ENGC) == (I2C_CR1_ENGC));
		522	}
		523
		524	/**
		525	* @brief Set the Own Address1.
		526	* @rmtoll OAR1 ADD0 LL_I2C_SetOwnAddress1\n
		527	* OAR1 ADD1_7 LL_I2C_SetOwnAddress1\n
		528	* OAR1 ADD8_9 LL_I2C_SetOwnAddress1\n
		529	* OAR1 ADDMODE LL_I2C_SetOwnAddress1
		530	* @param I2Cx I2C Instance.
		531	* @param OwnAddress1 This parameter must be a value between Min_Data=0 and Max_Data=0x3FF.
		532	* @param OwnAddrSize This parameter can be one of the following values:
		533	* @arg @ref LL_I2C_OWNADDRESS1_7BIT
		534	* @arg @ref LL_I2C_OWNADDRESS1_10BIT
		535	* @retval None
		536	*/
		537	__STATIC_INLINE void LL_I2C_SetOwnAddress1(I2C_TypeDef *I2Cx, uint32_t OwnAddress1, uint32_t OwnAddrSize)
		538	{
		539	MODIFY_REG(I2Cx->OAR1, I2C_OAR1_ADD0 \| I2C_OAR1_ADD1_7 \| I2C_OAR1_ADD8_9 \| I2C_OAR1_ADDMODE, OwnAddress1 \| OwnAddrSize);
		540	}
		541
		542	/**
		543	* @brief Set the 7bits Own Address2.
		544	* @note This action has no effect if own address2 is enabled.
		545	* @rmtoll OAR2 ADD2 LL_I2C_SetOwnAddress2
		546	* @param I2Cx I2C Instance.
		547	* @param OwnAddress2 This parameter must be a value between Min_Data=0 and Max_Data=0x7F.
		548	* @retval None
		549	*/
		550	__STATIC_INLINE void LL_I2C_SetOwnAddress2(I2C_TypeDef *I2Cx, uint32_t OwnAddress2)
		551	{
		552	MODIFY_REG(I2Cx->OAR2, I2C_OAR2_ADD2, OwnAddress2);
		553	}
		554
		555	/**
		556	* @brief Enable acknowledge on Own Address2 match address.
		557	* @rmtoll OAR2 ENDUAL LL_I2C_EnableOwnAddress2
		558	* @param I2Cx I2C Instance.
		559	* @retval None
		560	*/
		561	__STATIC_INLINE void LL_I2C_EnableOwnAddress2(I2C_TypeDef *I2Cx)
		562	{
		563	SET_BIT(I2Cx->OAR2, I2C_OAR2_ENDUAL);
		564	}
		565
		566	/**
		567	* @brief Disable acknowledge on Own Address2 match address.
		568	* @rmtoll OAR2 ENDUAL LL_I2C_DisableOwnAddress2
		569	* @param I2Cx I2C Instance.
		570	* @retval None
		571	*/
		572	__STATIC_INLINE void LL_I2C_DisableOwnAddress2(I2C_TypeDef *I2Cx)
		573	{
		574	CLEAR_BIT(I2Cx->OAR2, I2C_OAR2_ENDUAL);
		575	}
		576
		577	/**
		578	* @brief Check if Own Address1 acknowledge is enabled or disabled.
		579	* @rmtoll OAR2 ENDUAL LL_I2C_IsEnabledOwnAddress2
		580	* @param I2Cx I2C Instance.
		581	* @retval State of bit (1 or 0).
		582	*/
		583	__STATIC_INLINE uint32_t LL_I2C_IsEnabledOwnAddress2(I2C_TypeDef *I2Cx)
		584	{
		585	return (READ_BIT(I2Cx->OAR2, I2C_OAR2_ENDUAL) == (I2C_OAR2_ENDUAL));
		586	}
		587
		588	/**
		589	* @brief Configure the Peripheral clock frequency.
		590	* @rmtoll CR2 FREQ LL_I2C_SetPeriphClock
		591	* @param I2Cx I2C Instance.
		592	* @param PeriphClock Peripheral Clock (in Hz)
		593	* @retval None
		594	*/
		595	__STATIC_INLINE void LL_I2C_SetPeriphClock(I2C_TypeDef *I2Cx, uint32_t PeriphClock)
		596	{
		597	MODIFY_REG(I2Cx->CR2, I2C_CR2_FREQ, __LL_I2C_FREQ_HZ_TO_MHZ(PeriphClock));
		598	}
		599
		600	/**
		601	* @brief Get the Peripheral clock frequency.
		602	* @rmtoll CR2 FREQ LL_I2C_GetPeriphClock
		603	* @param I2Cx I2C Instance.
		604	* @retval Value of Peripheral Clock (in Hz)
		605	*/
		606	__STATIC_INLINE uint32_t LL_I2C_GetPeriphClock(I2C_TypeDef *I2Cx)
		607	{
		608	return (uint32_t)(__LL_I2C_FREQ_MHZ_TO_HZ(READ_BIT(I2Cx->CR2, I2C_CR2_FREQ)));
		609	}
		610
		611	/**
		612	* @brief Configure the Duty cycle (Fast mode only).
		613	* @rmtoll CCR DUTY LL_I2C_SetDutyCycle
		614	* @param I2Cx I2C Instance.
		615	* @param DutyCycle This parameter can be one of the following values:
		616	* @arg @ref LL_I2C_DUTYCYCLE_2
		617	* @arg @ref LL_I2C_DUTYCYCLE_16_9
		618	* @retval None
		619	*/
		620	__STATIC_INLINE void LL_I2C_SetDutyCycle(I2C_TypeDef *I2Cx, uint32_t DutyCycle)
		621	{
		622	MODIFY_REG(I2Cx->CCR, I2C_CCR_DUTY, DutyCycle);
		623	}
		624
		625	/**
		626	* @brief Get the Duty cycle (Fast mode only).
		627	* @rmtoll CCR DUTY LL_I2C_GetDutyCycle
		628	* @param I2Cx I2C Instance.
		629	* @retval Returned value can be one of the following values:
		630	* @arg @ref LL_I2C_DUTYCYCLE_2
		631	* @arg @ref LL_I2C_DUTYCYCLE_16_9
		632	*/
		633	__STATIC_INLINE uint32_t LL_I2C_GetDutyCycle(I2C_TypeDef *I2Cx)
		634	{
		635	return (uint32_t)(READ_BIT(I2Cx->CCR, I2C_CCR_DUTY));
		636	}
		637
		638	/**
		639	* @brief Configure the I2C master clock speed mode.
		640	* @rmtoll CCR FS LL_I2C_SetClockSpeedMode
		641	* @param I2Cx I2C Instance.
		642	* @param ClockSpeedMode This parameter can be one of the following values:
		643	* @arg @ref LL_I2C_CLOCK_SPEED_STANDARD_MODE
		644	* @arg @ref LL_I2C_CLOCK_SPEED_FAST_MODE
		645	* @retval None
		646	*/
		647	__STATIC_INLINE void LL_I2C_SetClockSpeedMode(I2C_TypeDef *I2Cx, uint32_t ClockSpeedMode)
		648	{
		649	MODIFY_REG(I2Cx->CCR, I2C_CCR_FS, ClockSpeedMode);
		650	}
		651
		652	/**
		653	* @brief Get the the I2C master speed mode.
		654	* @rmtoll CCR FS LL_I2C_GetClockSpeedMode
		655	* @param I2Cx I2C Instance.
		656	* @retval Returned value can be one of the following values:
		657	* @arg @ref LL_I2C_CLOCK_SPEED_STANDARD_MODE
		658	* @arg @ref LL_I2C_CLOCK_SPEED_FAST_MODE
		659	*/
		660	__STATIC_INLINE uint32_t LL_I2C_GetClockSpeedMode(I2C_TypeDef *I2Cx)
		661	{
		662	return (uint32_t)(READ_BIT(I2Cx->CCR, I2C_CCR_FS));
		663	}
		664
		665	/**
		666	* @brief Configure the SCL, SDA rising time.
		667	* @note This bit can only be programmed when the I2C is disabled (PE = 0).
		668	* @rmtoll TRISE TRISE LL_I2C_SetRiseTime
		669	* @param I2Cx I2C Instance.
		670	* @param RiseTime This parameter must be a value between Min_Data=0x02 and Max_Data=0x3F.
		671	* @retval None
		672	*/
		673	__STATIC_INLINE void LL_I2C_SetRiseTime(I2C_TypeDef *I2Cx, uint32_t RiseTime)
		674	{
		675	MODIFY_REG(I2Cx->TRISE, I2C_TRISE_TRISE, RiseTime);
		676	}
		677
		678	/**
		679	* @brief Get the SCL, SDA rising time.
		680	* @rmtoll TRISE TRISE LL_I2C_GetRiseTime
		681	* @param I2Cx I2C Instance.
		682	* @retval Value between Min_Data=0x02 and Max_Data=0x3F
		683	*/
		684	__STATIC_INLINE uint32_t LL_I2C_GetRiseTime(I2C_TypeDef *I2Cx)
		685	{
		686	return (uint32_t)(READ_BIT(I2Cx->TRISE, I2C_TRISE_TRISE));
		687	}
		688
		689	/**
		690	* @brief Configure the SCL high and low period.
		691	* @note This bit can only be programmed when the I2C is disabled (PE = 0).
		692	* @rmtoll CCR CCR LL_I2C_SetClockPeriod
		693	* @param I2Cx I2C Instance.
		694	* @param ClockPeriod This parameter must be a value between Min_Data=0x004 and Max_Data=0xFFF, except in FAST DUTY mode where Min_Data=0x001.
		695	* @retval None
		696	*/
		697	__STATIC_INLINE void LL_I2C_SetClockPeriod(I2C_TypeDef *I2Cx, uint32_t ClockPeriod)
		698	{
		699	MODIFY_REG(I2Cx->CCR, I2C_CCR_CCR, ClockPeriod);
		700	}
		701
		702	/**
		703	* @brief Get the SCL high and low period.
		704	* @rmtoll CCR CCR LL_I2C_GetClockPeriod
		705	* @param I2Cx I2C Instance.
		706	* @retval Value between Min_Data=0x004 and Max_Data=0xFFF, except in FAST DUTY mode where Min_Data=0x001.
		707	*/
		708	__STATIC_INLINE uint32_t LL_I2C_GetClockPeriod(I2C_TypeDef *I2Cx)
		709	{
		710	return (uint32_t)(READ_BIT(I2Cx->CCR, I2C_CCR_CCR));
		711	}
		712
		713	/**
		714	* @brief Configure the SCL speed.
		715	* @note This bit can only be programmed when the I2C is disabled (PE = 0).
		716	* @rmtoll CR2 FREQ LL_I2C_ConfigSpeed\n
		717	* TRISE TRISE LL_I2C_ConfigSpeed\n
		718	* CCR FS LL_I2C_ConfigSpeed\n
		719	* CCR DUTY LL_I2C_ConfigSpeed\n
		720	* CCR CCR LL_I2C_ConfigSpeed
		721	* @param I2Cx I2C Instance.
		722	* @param PeriphClock Peripheral Clock (in Hz)
		723	* @param ClockSpeed This parameter must be a value lower than 400kHz (in Hz).
		724	* @param DutyCycle This parameter can be one of the following values:
		725	* @arg @ref LL_I2C_DUTYCYCLE_2
		726	* @arg @ref LL_I2C_DUTYCYCLE_16_9
		727	* @retval None
		728	*/
		729	__STATIC_INLINE void LL_I2C_ConfigSpeed(I2C_TypeDef *I2Cx, uint32_t PeriphClock, uint32_t ClockSpeed,
		730	uint32_t DutyCycle)
		731	{
9	mjames	732	uint32_t freqrange = 0x0U;
		733	uint32_t clockconfig = 0x0U;
2	mjames	734
		735	/* Compute frequency range */
		736	freqrange = __LL_I2C_FREQ_HZ_TO_MHZ(PeriphClock);
		737
		738	/* Configure I2Cx: Frequency range register */
		739	MODIFY_REG(I2Cx->CR2, I2C_CR2_FREQ, freqrange);
		740
		741	/* Configure I2Cx: Rise Time register */
		742	MODIFY_REG(I2Cx->TRISE, I2C_TRISE_TRISE, __LL_I2C_RISE_TIME(freqrange, ClockSpeed));
		743
		744	/* Configure Speed mode, Duty Cycle and Clock control register value */
		745	if (ClockSpeed > LL_I2C_MAX_SPEED_STANDARD)
		746	{
		747	/* Set Speed mode at fast and duty cycle for Clock Speed request in fast clock range */
		748	clockconfig = LL_I2C_CLOCK_SPEED_FAST_MODE \| \
		749	__LL_I2C_SPEED_FAST_TO_CCR(PeriphClock, ClockSpeed, DutyCycle) \| \
		750	DutyCycle;
		751	}
		752	else
		753	{
		754	/* Set Speed mode at standard for Clock Speed request in standard clock range */
		755	clockconfig = LL_I2C_CLOCK_SPEED_STANDARD_MODE \| \
		756	__LL_I2C_SPEED_STANDARD_TO_CCR(PeriphClock, ClockSpeed);
		757	}
		758
		759	/* Configure I2Cx: Clock control register */
		760	MODIFY_REG(I2Cx->CCR, (I2C_CCR_FS \| I2C_CCR_DUTY \| I2C_CCR_CCR), clockconfig);
		761	}
		762
		763	/**
		764	* @brief Configure peripheral mode.
		765	* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
		766	* SMBus feature is supported by the I2Cx Instance.
		767	* @rmtoll CR1 SMBUS LL_I2C_SetMode\n
		768	* CR1 SMBTYPE LL_I2C_SetMode\n
		769	* CR1 ENARP LL_I2C_SetMode
		770	* @param I2Cx I2C Instance.
		771	* @param PeripheralMode This parameter can be one of the following values:
		772	* @arg @ref LL_I2C_MODE_I2C
		773	* @arg @ref LL_I2C_MODE_SMBUS_HOST
		774	* @arg @ref LL_I2C_MODE_SMBUS_DEVICE
		775	* @arg @ref LL_I2C_MODE_SMBUS_DEVICE_ARP
		776	* @retval None
		777	*/
		778	__STATIC_INLINE void LL_I2C_SetMode(I2C_TypeDef *I2Cx, uint32_t PeripheralMode)
		779	{
		780	MODIFY_REG(I2Cx->CR1, I2C_CR1_SMBUS \| I2C_CR1_SMBTYPE \| I2C_CR1_ENARP, PeripheralMode);
		781	}
		782
		783	/**
		784	* @brief Get peripheral mode.
		785	* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
		786	* SMBus feature is supported by the I2Cx Instance.
		787	* @rmtoll CR1 SMBUS LL_I2C_GetMode\n
		788	* CR1 SMBTYPE LL_I2C_GetMode\n
		789	* CR1 ENARP LL_I2C_GetMode
		790	* @param I2Cx I2C Instance.
		791	* @retval Returned value can be one of the following values:
		792	* @arg @ref LL_I2C_MODE_I2C
		793	* @arg @ref LL_I2C_MODE_SMBUS_HOST
		794	* @arg @ref LL_I2C_MODE_SMBUS_DEVICE
		795	* @arg @ref LL_I2C_MODE_SMBUS_DEVICE_ARP
		796	*/
		797	__STATIC_INLINE uint32_t LL_I2C_GetMode(I2C_TypeDef *I2Cx)
		798	{
		799	return (uint32_t)(READ_BIT(I2Cx->CR1, I2C_CR1_SMBUS \| I2C_CR1_SMBTYPE \| I2C_CR1_ENARP));
		800	}
		801
		802	/**
		803	* @brief Enable SMBus alert (Host or Device mode)
		804	* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
		805	* SMBus feature is supported by the I2Cx Instance.
		806	* @note SMBus Device mode:
		807	* - SMBus Alert pin is drived low and
		808	* Alert Response Address Header acknowledge is enabled.
		809	* SMBus Host mode:
		810	* - SMBus Alert pin management is supported.
		811	* @rmtoll CR1 ALERT LL_I2C_EnableSMBusAlert
		812	* @param I2Cx I2C Instance.
		813	* @retval None
		814	*/
		815	__STATIC_INLINE void LL_I2C_EnableSMBusAlert(I2C_TypeDef *I2Cx)
		816	{
		817	SET_BIT(I2Cx->CR1, I2C_CR1_ALERT);
		818	}
		819
		820	/**
		821	* @brief Disable SMBus alert (Host or Device mode)
		822	* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
		823	* SMBus feature is supported by the I2Cx Instance.
		824	* @note SMBus Device mode:
		825	* - SMBus Alert pin is not drived (can be used as a standard GPIO) and
		826	* Alert Response Address Header acknowledge is disabled.
		827	* SMBus Host mode:
		828	* - SMBus Alert pin management is not supported.
		829	* @rmtoll CR1 ALERT LL_I2C_DisableSMBusAlert
		830	* @param I2Cx I2C Instance.
		831	* @retval None
		832	*/
		833	__STATIC_INLINE void LL_I2C_DisableSMBusAlert(I2C_TypeDef *I2Cx)
		834	{
		835	CLEAR_BIT(I2Cx->CR1, I2C_CR1_ALERT);
		836	}
		837
		838	/**
		839	* @brief Check if SMBus alert (Host or Device mode) is enabled or disabled.
		840	* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
		841	* SMBus feature is supported by the I2Cx Instance.
		842	* @rmtoll CR1 ALERT LL_I2C_IsEnabledSMBusAlert
		843	* @param I2Cx I2C Instance.
		844	* @retval State of bit (1 or 0).
		845	*/
		846	__STATIC_INLINE uint32_t LL_I2C_IsEnabledSMBusAlert(I2C_TypeDef *I2Cx)
		847	{
		848	return (READ_BIT(I2Cx->CR1, I2C_CR1_ALERT) == (I2C_CR1_ALERT));
		849	}
		850
		851	/**
		852	* @brief Enable SMBus Packet Error Calculation (PEC).
		853	* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
		854	* SMBus feature is supported by the I2Cx Instance.
		855	* @rmtoll CR1 ENPEC LL_I2C_EnableSMBusPEC
		856	* @param I2Cx I2C Instance.
		857	* @retval None
		858	*/
		859	__STATIC_INLINE void LL_I2C_EnableSMBusPEC(I2C_TypeDef *I2Cx)
		860	{
		861	SET_BIT(I2Cx->CR1, I2C_CR1_ENPEC);
		862	}
		863
		864	/**
		865	* @brief Disable SMBus Packet Error Calculation (PEC).
		866	* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
		867	* SMBus feature is supported by the I2Cx Instance.
		868	* @rmtoll CR1 ENPEC LL_I2C_DisableSMBusPEC
		869	* @param I2Cx I2C Instance.
		870	* @retval None
		871	*/
		872	__STATIC_INLINE void LL_I2C_DisableSMBusPEC(I2C_TypeDef *I2Cx)
		873	{
		874	CLEAR_BIT(I2Cx->CR1, I2C_CR1_ENPEC);
		875	}
		876
		877	/**
		878	* @brief Check if SMBus Packet Error Calculation (PEC) is enabled or disabled.
		879	* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
		880	* SMBus feature is supported by the I2Cx Instance.
		881	* @rmtoll CR1 ENPEC LL_I2C_IsEnabledSMBusPEC
		882	* @param I2Cx I2C Instance.
		883	* @retval State of bit (1 or 0).
		884	*/
		885	__STATIC_INLINE uint32_t LL_I2C_IsEnabledSMBusPEC(I2C_TypeDef *I2Cx)
		886	{
		887	return (READ_BIT(I2Cx->CR1, I2C_CR1_ENPEC) == (I2C_CR1_ENPEC));
		888	}
		889
		890	/**
		891	* @}
		892	*/
		893
		894	/** @defgroup I2C_LL_EF_IT_Management IT_Management
		895	* @{
		896	*/
		897
		898	/**
		899	* @brief Enable TXE interrupt.
		900	* @rmtoll CR2 ITEVTEN LL_I2C_EnableIT_TX\n
		901	* CR2 ITBUFEN LL_I2C_EnableIT_TX
		902	* @param I2Cx I2C Instance.
		903	* @retval None
		904	*/
		905	__STATIC_INLINE void LL_I2C_EnableIT_TX(I2C_TypeDef *I2Cx)
		906	{
		907	SET_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN \| I2C_CR2_ITBUFEN);
		908	}
		909
		910	/**
		911	* @brief Disable TXE interrupt.
		912	* @rmtoll CR2 ITEVTEN LL_I2C_DisableIT_TX\n
		913	* CR2 ITBUFEN LL_I2C_DisableIT_TX
		914	* @param I2Cx I2C Instance.
		915	* @retval None
		916	*/
		917	__STATIC_INLINE void LL_I2C_DisableIT_TX(I2C_TypeDef *I2Cx)
		918	{
		919	CLEAR_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN \| I2C_CR2_ITBUFEN);
		920	}
		921
		922	/**
		923	* @brief Check if the TXE Interrupt is enabled or disabled.
		924	* @rmtoll CR2 ITEVTEN LL_I2C_IsEnabledIT_TX\n
		925	* CR2 ITBUFEN LL_I2C_IsEnabledIT_TX
		926	* @param I2Cx I2C Instance.
		927	* @retval State of bit (1 or 0).
		928	*/
		929	__STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_TX(I2C_TypeDef *I2Cx)
		930	{
		931	return (READ_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN \| I2C_CR2_ITBUFEN) == (I2C_CR2_ITEVTEN \| I2C_CR2_ITBUFEN));
		932	}
		933
		934	/**
		935	* @brief Enable RXNE interrupt.
		936	* @rmtoll CR2 ITEVTEN LL_I2C_EnableIT_RX\n
		937	* CR2 ITBUFEN LL_I2C_EnableIT_RX
		938	* @param I2Cx I2C Instance.
		939	* @retval None
		940	*/
		941	__STATIC_INLINE void LL_I2C_EnableIT_RX(I2C_TypeDef *I2Cx)
		942	{
		943	SET_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN \| I2C_CR2_ITBUFEN);
		944	}
		945
		946	/**
		947	* @brief Disable RXNE interrupt.
		948	* @rmtoll CR2 ITEVTEN LL_I2C_DisableIT_RX\n
		949	* CR2 ITBUFEN LL_I2C_DisableIT_RX
		950	* @param I2Cx I2C Instance.
		951	* @retval None
		952	*/
		953	__STATIC_INLINE void LL_I2C_DisableIT_RX(I2C_TypeDef *I2Cx)
		954	{
		955	CLEAR_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN \| I2C_CR2_ITBUFEN);
		956	}
		957
		958	/**
		959	* @brief Check if the RXNE Interrupt is enabled or disabled.
		960	* @rmtoll CR2 ITEVTEN LL_I2C_IsEnabledIT_RX\n
		961	* CR2 ITBUFEN LL_I2C_IsEnabledIT_RX
		962	* @param I2Cx I2C Instance.
		963	* @retval State of bit (1 or 0).
		964	*/
		965	__STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_RX(I2C_TypeDef *I2Cx)
		966	{
		967	return (READ_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN \| I2C_CR2_ITBUFEN) == (I2C_CR2_ITEVTEN \| I2C_CR2_ITBUFEN));
		968	}
		969
		970	/**
		971	* @brief Enable Events interrupts.
		972	* @note Any of these events will generate interrupt :
		973	* Start Bit (SB)
		974	* Address sent, Address matched (ADDR)
		975	* 10-bit header sent (ADD10)
		976	* Stop detection (STOPF)
		977	* Byte transfer finished (BTF)
		978	*
		979	* @note Any of these events will generate interrupt if Buffer interrupts are enabled too(using unitary function @ref LL_I2C_EnableIT_BUF()) :
		980	* Receive buffer not empty (RXNE)
		981	* Transmit buffer empty (TXE)
		982	* @rmtoll CR2 ITEVTEN LL_I2C_EnableIT_EVT
		983	* @param I2Cx I2C Instance.
		984	* @retval None
		985	*/
		986	__STATIC_INLINE void LL_I2C_EnableIT_EVT(I2C_TypeDef *I2Cx)
		987	{
		988	SET_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN);
		989	}
		990
		991	/**
		992	* @brief Disable Events interrupts.
		993	* @note Any of these events will generate interrupt :
		994	* Start Bit (SB)
		995	* Address sent, Address matched (ADDR)
		996	* 10-bit header sent (ADD10)
		997	* Stop detection (STOPF)
		998	* Byte transfer finished (BTF)
		999	* Receive buffer not empty (RXNE)
		1000	* Transmit buffer empty (TXE)
		1001	* @rmtoll CR2 ITEVTEN LL_I2C_DisableIT_EVT
		1002	* @param I2Cx I2C Instance.
		1003	* @retval None
		1004	*/
		1005	__STATIC_INLINE void LL_I2C_DisableIT_EVT(I2C_TypeDef *I2Cx)
		1006	{
		1007	CLEAR_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN);
		1008	}
		1009
		1010	/**
		1011	* @brief Check if Events interrupts are enabled or disabled.
		1012	* @rmtoll CR2 ITEVTEN LL_I2C_IsEnabledIT_EVT
		1013	* @param I2Cx I2C Instance.
		1014	* @retval State of bit (1 or 0).
		1015	*/
		1016	__STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_EVT(I2C_TypeDef *I2Cx)
		1017	{
		1018	return (READ_BIT(I2Cx->CR2, I2C_CR2_ITEVTEN) == (I2C_CR2_ITEVTEN));
		1019	}
		1020
		1021	/**
		1022	* @brief Enable Buffer interrupts.
		1023	* @note Any of these Buffer events will generate interrupt if Events interrupts are enabled too(using unitary function @ref LL_I2C_EnableIT_EVT()) :
		1024	* Receive buffer not empty (RXNE)
		1025	* Transmit buffer empty (TXE)
		1026	* @rmtoll CR2 ITBUFEN LL_I2C_EnableIT_BUF
		1027	* @param I2Cx I2C Instance.
		1028	* @retval None
		1029	*/
		1030	__STATIC_INLINE void LL_I2C_EnableIT_BUF(I2C_TypeDef *I2Cx)
		1031	{
		1032	SET_BIT(I2Cx->CR2, I2C_CR2_ITBUFEN);
		1033	}
		1034
		1035	/**
		1036	* @brief Disable Buffer interrupts.
		1037	* @note Any of these Buffer events will generate interrupt :
		1038	* Receive buffer not empty (RXNE)
		1039	* Transmit buffer empty (TXE)
		1040	* @rmtoll CR2 ITBUFEN LL_I2C_DisableIT_BUF
		1041	* @param I2Cx I2C Instance.
		1042	* @retval None
		1043	*/
		1044	__STATIC_INLINE void LL_I2C_DisableIT_BUF(I2C_TypeDef *I2Cx)
		1045	{
		1046	CLEAR_BIT(I2Cx->CR2, I2C_CR2_ITBUFEN);
		1047	}
		1048
		1049	/**
		1050	* @brief Check if Buffer interrupts are enabled or disabled.
		1051	* @rmtoll CR2 ITBUFEN LL_I2C_IsEnabledIT_BUF
		1052	* @param I2Cx I2C Instance.
		1053	* @retval State of bit (1 or 0).
		1054	*/
		1055	__STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_BUF(I2C_TypeDef *I2Cx)
		1056	{
		1057	return (READ_BIT(I2Cx->CR2, I2C_CR2_ITBUFEN) == (I2C_CR2_ITBUFEN));
		1058	}
		1059
		1060	/**
		1061	* @brief Enable Error interrupts.
		1062	* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
		1063	* SMBus feature is supported by the I2Cx Instance.
		1064	* @note Any of these errors will generate interrupt :
		1065	* Bus Error detection (BERR)
		1066	* Arbitration Loss (ARLO)
		1067	* Acknowledge Failure(AF)
		1068	* Overrun/Underrun (OVR)
		1069	* SMBus Timeout detection (TIMEOUT)
		1070	* SMBus PEC error detection (PECERR)
		1071	* SMBus Alert pin event detection (SMBALERT)
		1072	* @rmtoll CR2 ITERREN LL_I2C_EnableIT_ERR
		1073	* @param I2Cx I2C Instance.
		1074	* @retval None
		1075	*/
		1076	__STATIC_INLINE void LL_I2C_EnableIT_ERR(I2C_TypeDef *I2Cx)
		1077	{
		1078	SET_BIT(I2Cx->CR2, I2C_CR2_ITERREN);
		1079	}
		1080
		1081	/**
		1082	* @brief Disable Error interrupts.
		1083	* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
		1084	* SMBus feature is supported by the I2Cx Instance.
		1085	* @note Any of these errors will generate interrupt :
		1086	* Bus Error detection (BERR)
		1087	* Arbitration Loss (ARLO)
		1088	* Acknowledge Failure(AF)
		1089	* Overrun/Underrun (OVR)
		1090	* SMBus Timeout detection (TIMEOUT)
		1091	* SMBus PEC error detection (PECERR)
		1092	* SMBus Alert pin event detection (SMBALERT)
		1093	* @rmtoll CR2 ITERREN LL_I2C_DisableIT_ERR
		1094	* @param I2Cx I2C Instance.
		1095	* @retval None
		1096	*/
		1097	__STATIC_INLINE void LL_I2C_DisableIT_ERR(I2C_TypeDef *I2Cx)
		1098	{
		1099	CLEAR_BIT(I2Cx->CR2, I2C_CR2_ITERREN);
		1100	}
		1101
		1102	/**
		1103	* @brief Check if Error interrupts are enabled or disabled.
		1104	* @rmtoll CR2 ITERREN LL_I2C_IsEnabledIT_ERR
		1105	* @param I2Cx I2C Instance.
		1106	* @retval State of bit (1 or 0).
		1107	*/
		1108	__STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_ERR(I2C_TypeDef *I2Cx)
		1109	{
		1110	return (READ_BIT(I2Cx->CR2, I2C_CR2_ITERREN) == (I2C_CR2_ITERREN));
		1111	}
		1112
		1113	/**
		1114	* @}
		1115	*/
		1116
		1117	/** @defgroup I2C_LL_EF_FLAG_management FLAG_management
		1118	* @{
		1119	*/
		1120
		1121	/**
		1122	* @brief Indicate the status of Transmit data register empty flag.
		1123	* @note RESET: When next data is written in Transmit data register.
		1124	* SET: When Transmit data register is empty.
		1125	* @rmtoll SR1 TXE LL_I2C_IsActiveFlag_TXE
		1126	* @param I2Cx I2C Instance.
		1127	* @retval State of bit (1 or 0).
		1128	*/
		1129	__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_TXE(I2C_TypeDef *I2Cx)
		1130	{
		1131	return (READ_BIT(I2Cx->SR1, I2C_SR1_TXE) == (I2C_SR1_TXE));
		1132	}
		1133
		1134	/**
		1135	* @brief Indicate the status of Byte Transfer Finished flag.
		1136	* RESET: When Data byte transfer not done.
		1137	* SET: When Data byte transfer succeeded.
		1138	* @rmtoll SR1 BTF LL_I2C_IsActiveFlag_BTF
		1139	* @param I2Cx I2C Instance.
		1140	* @retval State of bit (1 or 0).
		1141	*/
		1142	__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_BTF(I2C_TypeDef *I2Cx)
		1143	{
		1144	return (READ_BIT(I2Cx->SR1, I2C_SR1_BTF) == (I2C_SR1_BTF));
		1145	}
		1146
		1147	/**
		1148	* @brief Indicate the status of Receive data register not empty flag.
		1149	* @note RESET: When Receive data register is read.
		1150	* SET: When the received data is copied in Receive data register.
		1151	* @rmtoll SR1 RXNE LL_I2C_IsActiveFlag_RXNE
		1152	* @param I2Cx I2C Instance.
		1153	* @retval State of bit (1 or 0).
		1154	*/
		1155	__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_RXNE(I2C_TypeDef *I2Cx)
		1156	{
		1157	return (READ_BIT(I2Cx->SR1, I2C_SR1_RXNE) == (I2C_SR1_RXNE));
		1158	}
		1159
		1160	/**
		1161	* @brief Indicate the status of Start Bit (master mode).
		1162	* @note RESET: When No Start condition.
		1163	* SET: When Start condition is generated.
		1164	* @rmtoll SR1 SB LL_I2C_IsActiveFlag_SB
		1165	* @param I2Cx I2C Instance.
		1166	* @retval State of bit (1 or 0).
		1167	*/
		1168	__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_SB(I2C_TypeDef *I2Cx)
		1169	{
		1170	return (READ_BIT(I2Cx->SR1, I2C_SR1_SB) == (I2C_SR1_SB));
		1171	}
		1172
		1173	/**
		1174	* @brief Indicate the status of Address sent (master mode) or Address matched flag (slave mode).
		1175	* @note RESET: Clear default value.
		1176	* SET: When the address is fully sent (master mode) or when the received slave address matched with one of the enabled slave address (slave mode).
		1177	* @rmtoll SR1 ADDR LL_I2C_IsActiveFlag_ADDR
		1178	* @param I2Cx I2C Instance.
		1179	* @retval State of bit (1 or 0).
		1180	*/
		1181	__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_ADDR(I2C_TypeDef *I2Cx)
		1182	{
		1183	return (READ_BIT(I2Cx->SR1, I2C_SR1_ADDR) == (I2C_SR1_ADDR));
		1184	}
		1185
		1186	/**
		1187	* @brief Indicate the status of 10-bit header sent (master mode).
9	mjames	1188	* @note RESET: When no ADD10 event occurred.
2	mjames	1189	* SET: When the master has sent the first address byte (header).
		1190	* @rmtoll SR1 ADD10 LL_I2C_IsActiveFlag_ADD10
		1191	* @param I2Cx I2C Instance.
		1192	* @retval State of bit (1 or 0).
		1193	*/
		1194	__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_ADD10(I2C_TypeDef *I2Cx)
		1195	{
		1196	return (READ_BIT(I2Cx->SR1, I2C_SR1_ADD10) == (I2C_SR1_ADD10));
		1197	}
		1198
		1199	/**
		1200	* @brief Indicate the status of Acknowledge failure flag.
		1201	* @note RESET: No acknowledge failure.
		1202	* SET: When an acknowledge failure is received after a byte transmission.
		1203	* @rmtoll SR1 AF LL_I2C_IsActiveFlag_AF
		1204	* @param I2Cx I2C Instance.
		1205	* @retval State of bit (1 or 0).
		1206	*/
		1207	__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_AF(I2C_TypeDef *I2Cx)
		1208	{
		1209	return (READ_BIT(I2Cx->SR1, I2C_SR1_AF) == (I2C_SR1_AF));
		1210	}
		1211
		1212	/**
		1213	* @brief Indicate the status of Stop detection flag (slave mode).
		1214	* @note RESET: Clear default value.
		1215	* SET: When a Stop condition is detected.
		1216	* @rmtoll SR1 STOPF LL_I2C_IsActiveFlag_STOP
		1217	* @param I2Cx I2C Instance.
		1218	* @retval State of bit (1 or 0).
		1219	*/
		1220	__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_STOP(I2C_TypeDef *I2Cx)
		1221	{
		1222	return (READ_BIT(I2Cx->SR1, I2C_SR1_STOPF) == (I2C_SR1_STOPF));
		1223	}
		1224
		1225	/**
		1226	* @brief Indicate the status of Bus error flag.
		1227	* @note RESET: Clear default value.
		1228	* SET: When a misplaced Start or Stop condition is detected.
		1229	* @rmtoll SR1 BERR LL_I2C_IsActiveFlag_BERR
		1230	* @param I2Cx I2C Instance.
		1231	* @retval State of bit (1 or 0).
		1232	*/
		1233	__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_BERR(I2C_TypeDef *I2Cx)
		1234	{
		1235	return (READ_BIT(I2Cx->SR1, I2C_SR1_BERR) == (I2C_SR1_BERR));
		1236	}
		1237
		1238	/**
		1239	* @brief Indicate the status of Arbitration lost flag.
		1240	* @note RESET: Clear default value.
		1241	* SET: When arbitration lost.
		1242	* @rmtoll SR1 ARLO LL_I2C_IsActiveFlag_ARLO
		1243	* @param I2Cx I2C Instance.
		1244	* @retval State of bit (1 or 0).
		1245	*/
		1246	__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_ARLO(I2C_TypeDef *I2Cx)
		1247	{
		1248	return (READ_BIT(I2Cx->SR1, I2C_SR1_ARLO) == (I2C_SR1_ARLO));
		1249	}
		1250
		1251	/**
		1252	* @brief Indicate the status of Overrun/Underrun flag.
		1253	* @note RESET: Clear default value.
		1254	* SET: When an overrun/underrun error occurs (Clock Stretching Disabled).
		1255	* @rmtoll SR1 OVR LL_I2C_IsActiveFlag_OVR
		1256	* @param I2Cx I2C Instance.
		1257	* @retval State of bit (1 or 0).
		1258	*/
		1259	__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_OVR(I2C_TypeDef *I2Cx)
		1260	{
		1261	return (READ_BIT(I2Cx->SR1, I2C_SR1_OVR) == (I2C_SR1_OVR));
		1262	}
		1263
		1264	/**
		1265	* @brief Indicate the status of SMBus PEC error flag in reception.
		1266	* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
		1267	* SMBus feature is supported by the I2Cx Instance.
		1268	* @rmtoll SR1 PECERR LL_I2C_IsActiveSMBusFlag_PECERR
		1269	* @param I2Cx I2C Instance.
		1270	* @retval State of bit (1 or 0).
		1271	*/
		1272	__STATIC_INLINE uint32_t LL_I2C_IsActiveSMBusFlag_PECERR(I2C_TypeDef *I2Cx)
		1273	{
		1274	return (READ_BIT(I2Cx->SR1, I2C_SR1_PECERR) == (I2C_SR1_PECERR));
		1275	}
		1276
		1277	/**
		1278	* @brief Indicate the status of SMBus Timeout detection flag.
		1279	* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
		1280	* SMBus feature is supported by the I2Cx Instance.
		1281	* @rmtoll SR1 TIMEOUT LL_I2C_IsActiveSMBusFlag_TIMEOUT
		1282	* @param I2Cx I2C Instance.
		1283	* @retval State of bit (1 or 0).
		1284	*/
		1285	__STATIC_INLINE uint32_t LL_I2C_IsActiveSMBusFlag_TIMEOUT(I2C_TypeDef *I2Cx)
		1286	{
		1287	return (READ_BIT(I2Cx->SR1, I2C_SR1_TIMEOUT) == (I2C_SR1_TIMEOUT));
		1288	}
		1289
		1290	/**
		1291	* @brief Indicate the status of SMBus alert flag.
		1292	* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
		1293	* SMBus feature is supported by the I2Cx Instance.
		1294	* @rmtoll SR1 SMBALERT LL_I2C_IsActiveSMBusFlag_ALERT
		1295	* @param I2Cx I2C Instance.
		1296	* @retval State of bit (1 or 0).
		1297	*/
		1298	__STATIC_INLINE uint32_t LL_I2C_IsActiveSMBusFlag_ALERT(I2C_TypeDef *I2Cx)
		1299	{
		1300	return (READ_BIT(I2Cx->SR1, I2C_SR1_SMBALERT) == (I2C_SR1_SMBALERT));
		1301	}
		1302
		1303	/**
		1304	* @brief Indicate the status of Bus Busy flag.
		1305	* @note RESET: Clear default value.
		1306	* SET: When a Start condition is detected.
		1307	* @rmtoll SR2 BUSY LL_I2C_IsActiveFlag_BUSY
		1308	* @param I2Cx I2C Instance.
		1309	* @retval State of bit (1 or 0).
		1310	*/
		1311	__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_BUSY(I2C_TypeDef *I2Cx)
		1312	{
		1313	return (READ_BIT(I2Cx->SR2, I2C_SR2_BUSY) == (I2C_SR2_BUSY));
		1314	}
		1315
		1316	/**
		1317	* @brief Indicate the status of Dual flag.
		1318	* @note RESET: Received address matched with OAR1.
		1319	* SET: Received address matched with OAR2.
		1320	* @rmtoll SR2 DUALF LL_I2C_IsActiveFlag_DUAL
		1321	* @param I2Cx I2C Instance.
		1322	* @retval State of bit (1 or 0).
		1323	*/
		1324	__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_DUAL(I2C_TypeDef *I2Cx)
		1325	{
		1326	return (READ_BIT(I2Cx->SR2, I2C_SR2_DUALF) == (I2C_SR2_DUALF));
		1327	}
		1328
		1329	/**
		1330	* @brief Indicate the status of SMBus Host address reception (Slave mode).
		1331	* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
		1332	* SMBus feature is supported by the I2Cx Instance.
		1333	* @note RESET: No SMBus Host address
		1334	* SET: SMBus Host address received.
		1335	* @note This status is cleared by hardware after a STOP condition or repeated START condition.
		1336	* @rmtoll SR2 SMBHOST LL_I2C_IsActiveSMBusFlag_SMBHOST
		1337	* @param I2Cx I2C Instance.
		1338	* @retval State of bit (1 or 0).
		1339	*/
		1340	__STATIC_INLINE uint32_t LL_I2C_IsActiveSMBusFlag_SMBHOST(I2C_TypeDef *I2Cx)
		1341	{
		1342	return (READ_BIT(I2Cx->SR2, I2C_SR2_SMBHOST) == (I2C_SR2_SMBHOST));
		1343	}
		1344
		1345	/**
		1346	* @brief Indicate the status of SMBus Device default address reception (Slave mode).
		1347	* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
		1348	* SMBus feature is supported by the I2Cx Instance.
		1349	* @note RESET: No SMBus Device default address
		1350	* SET: SMBus Device default address received.
		1351	* @note This status is cleared by hardware after a STOP condition or repeated START condition.
		1352	* @rmtoll SR2 SMBDEFAULT LL_I2C_IsActiveSMBusFlag_SMBDEFAULT
		1353	* @param I2Cx I2C Instance.
		1354	* @retval State of bit (1 or 0).
		1355	*/
		1356	__STATIC_INLINE uint32_t LL_I2C_IsActiveSMBusFlag_SMBDEFAULT(I2C_TypeDef *I2Cx)
		1357	{
		1358	return (READ_BIT(I2Cx->SR2, I2C_SR2_SMBDEFAULT) == (I2C_SR2_SMBDEFAULT));
		1359	}
		1360
		1361	/**
		1362	* @brief Indicate the status of General call address reception (Slave mode).
		1363	* @note RESET: No Generall call address
		1364	* SET: General call address received.
		1365	* @note This status is cleared by hardware after a STOP condition or repeated START condition.
		1366	* @rmtoll SR2 GENCALL LL_I2C_IsActiveFlag_GENCALL
		1367	* @param I2Cx I2C Instance.
		1368	* @retval State of bit (1 or 0).
		1369	*/
		1370	__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_GENCALL(I2C_TypeDef *I2Cx)
		1371	{
		1372	return (READ_BIT(I2Cx->SR2, I2C_SR2_GENCALL) == (I2C_SR2_GENCALL));
		1373	}
		1374
		1375	/**
		1376	* @brief Indicate the status of Master/Slave flag.
		1377	* @note RESET: Slave Mode.
		1378	* SET: Master Mode.
		1379	* @rmtoll SR2 MSL LL_I2C_IsActiveFlag_MSL
		1380	* @param I2Cx I2C Instance.
		1381	* @retval State of bit (1 or 0).
		1382	*/
		1383	__STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_MSL(I2C_TypeDef *I2Cx)
		1384	{
		1385	return (READ_BIT(I2Cx->SR2, I2C_SR2_MSL) == (I2C_SR2_MSL));
		1386	}
		1387
		1388	/**
		1389	* @brief Clear Address Matched flag.
		1390	* @note Clearing this flag is done by a read access to the I2Cx_SR1
		1391	* register followed by a read access to the I2Cx_SR2 register.
		1392	* @rmtoll SR1 ADDR LL_I2C_ClearFlag_ADDR
		1393	* @param I2Cx I2C Instance.
		1394	* @retval None
		1395	*/
		1396	__STATIC_INLINE void LL_I2C_ClearFlag_ADDR(I2C_TypeDef *I2Cx)
		1397	{
		1398	__IO uint32_t tmpreg;
		1399	tmpreg = I2Cx->SR1;
		1400	(void) tmpreg;
		1401	tmpreg = I2Cx->SR2;
		1402	(void) tmpreg;
		1403	}
		1404
		1405	/**
		1406	* @brief Clear Acknowledge failure flag.
		1407	* @rmtoll SR1 AF LL_I2C_ClearFlag_AF
		1408	* @param I2Cx I2C Instance.
		1409	* @retval None
		1410	*/
		1411	__STATIC_INLINE void LL_I2C_ClearFlag_AF(I2C_TypeDef *I2Cx)
		1412	{
		1413	CLEAR_BIT(I2Cx->SR1, I2C_SR1_AF);
		1414	}
		1415
		1416	/**
		1417	* @brief Clear Stop detection flag.
		1418	* @note Clearing this flag is done by a read access to the I2Cx_SR1
		1419	* register followed by a write access to I2Cx_CR1 register.
		1420	* @rmtoll SR1 STOPF LL_I2C_ClearFlag_STOP\n
		1421	* CR1 PE LL_I2C_ClearFlag_STOP
		1422	* @param I2Cx I2C Instance.
		1423	* @retval None
		1424	*/
		1425	__STATIC_INLINE void LL_I2C_ClearFlag_STOP(I2C_TypeDef *I2Cx)
		1426	{
		1427	__IO uint32_t tmpreg;
		1428	tmpreg = I2Cx->SR1;
		1429	(void) tmpreg;
		1430	SET_BIT(I2Cx->CR1, I2C_CR1_PE);
		1431	}
		1432
		1433	/**
		1434	* @brief Clear Bus error flag.
		1435	* @rmtoll SR1 BERR LL_I2C_ClearFlag_BERR
		1436	* @param I2Cx I2C Instance.
		1437	* @retval None
		1438	*/
		1439	__STATIC_INLINE void LL_I2C_ClearFlag_BERR(I2C_TypeDef *I2Cx)
		1440	{
		1441	CLEAR_BIT(I2Cx->SR1, I2C_SR1_BERR);
		1442	}
		1443
		1444	/**
		1445	* @brief Clear Arbitration lost flag.
		1446	* @rmtoll SR1 ARLO LL_I2C_ClearFlag_ARLO
		1447	* @param I2Cx I2C Instance.
		1448	* @retval None
		1449	*/
		1450	__STATIC_INLINE void LL_I2C_ClearFlag_ARLO(I2C_TypeDef *I2Cx)
		1451	{
		1452	CLEAR_BIT(I2Cx->SR1, I2C_SR1_ARLO);
		1453	}
		1454
		1455	/**
		1456	* @brief Clear Overrun/Underrun flag.
		1457	* @rmtoll SR1 OVR LL_I2C_ClearFlag_OVR
		1458	* @param I2Cx I2C Instance.
		1459	* @retval None
		1460	*/
		1461	__STATIC_INLINE void LL_I2C_ClearFlag_OVR(I2C_TypeDef *I2Cx)
		1462	{
		1463	CLEAR_BIT(I2Cx->SR1, I2C_SR1_OVR);
		1464	}
		1465
		1466	/**
		1467	* @brief Clear SMBus PEC error flag.
		1468	* @rmtoll SR1 PECERR LL_I2C_ClearSMBusFlag_PECERR
		1469	* @param I2Cx I2C Instance.
		1470	* @retval None
		1471	*/
		1472	__STATIC_INLINE void LL_I2C_ClearSMBusFlag_PECERR(I2C_TypeDef *I2Cx)
		1473	{
		1474	CLEAR_BIT(I2Cx->SR1, I2C_SR1_PECERR);
		1475	}
		1476
		1477	/**
		1478	* @brief Clear SMBus Timeout detection flag.
		1479	* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
		1480	* SMBus feature is supported by the I2Cx Instance.
		1481	* @rmtoll SR1 TIMEOUT LL_I2C_ClearSMBusFlag_TIMEOUT
		1482	* @param I2Cx I2C Instance.
		1483	* @retval None
		1484	*/
		1485	__STATIC_INLINE void LL_I2C_ClearSMBusFlag_TIMEOUT(I2C_TypeDef *I2Cx)
		1486	{
		1487	CLEAR_BIT(I2Cx->SR1, I2C_SR1_TIMEOUT);
		1488	}
		1489
		1490	/**
		1491	* @brief Clear SMBus Alert flag.
		1492	* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
		1493	* SMBus feature is supported by the I2Cx Instance.
		1494	* @rmtoll SR1 SMBALERT LL_I2C_ClearSMBusFlag_ALERT
		1495	* @param I2Cx I2C Instance.
		1496	* @retval None
		1497	*/
		1498	__STATIC_INLINE void LL_I2C_ClearSMBusFlag_ALERT(I2C_TypeDef *I2Cx)
		1499	{
		1500	CLEAR_BIT(I2Cx->SR1, I2C_SR1_SMBALERT);
		1501	}
		1502
		1503	/**
		1504	* @}
		1505	*/
		1506
		1507	/** @defgroup I2C_LL_EF_Data_Management Data_Management
		1508	* @{
		1509	*/
		1510
		1511	/**
		1512	* @brief Enable Reset of I2C peripheral.
		1513	* @rmtoll CR1 SWRST LL_I2C_EnableReset
		1514	* @param I2Cx I2C Instance.
		1515	* @retval None
		1516	*/
		1517	__STATIC_INLINE void LL_I2C_EnableReset(I2C_TypeDef *I2Cx)
		1518	{
		1519	SET_BIT(I2Cx->CR1, I2C_CR1_SWRST);
		1520	}
		1521
		1522	/**
		1523	* @brief Disable Reset of I2C peripheral.
		1524	* @rmtoll CR1 SWRST LL_I2C_DisableReset
		1525	* @param I2Cx I2C Instance.
		1526	* @retval None
		1527	*/
		1528	__STATIC_INLINE void LL_I2C_DisableReset(I2C_TypeDef *I2Cx)
		1529	{
		1530	CLEAR_BIT(I2Cx->CR1, I2C_CR1_SWRST);
		1531	}
		1532
		1533	/**
		1534	* @brief Check if the I2C peripheral is under reset state or not.
		1535	* @rmtoll CR1 SWRST LL_I2C_IsResetEnabled
		1536	* @param I2Cx I2C Instance.
		1537	* @retval State of bit (1 or 0).
		1538	*/
		1539	__STATIC_INLINE uint32_t LL_I2C_IsResetEnabled(I2C_TypeDef *I2Cx)
		1540	{
		1541	return (READ_BIT(I2Cx->CR1, I2C_CR1_SWRST) == (I2C_CR1_SWRST));
		1542	}
		1543
		1544	/**
		1545	* @brief Prepare the generation of a ACKnowledge or Non ACKnowledge condition after the address receive match code or next received byte.
		1546	* @note Usage in Slave or Master mode.
		1547	* @rmtoll CR1 ACK LL_I2C_AcknowledgeNextData
		1548	* @param I2Cx I2C Instance.
		1549	* @param TypeAcknowledge This parameter can be one of the following values:
		1550	* @arg @ref LL_I2C_ACK
		1551	* @arg @ref LL_I2C_NACK
		1552	* @retval None
		1553	*/
		1554	__STATIC_INLINE void LL_I2C_AcknowledgeNextData(I2C_TypeDef *I2Cx, uint32_t TypeAcknowledge)
		1555	{
		1556	MODIFY_REG(I2Cx->CR1, I2C_CR1_ACK, TypeAcknowledge);
		1557	}
		1558
		1559	/**
		1560	* @brief Generate a START or RESTART condition
		1561	* @note The START bit can be set even if bus is BUSY or I2C is in slave mode.
		1562	* This action has no effect when RELOAD is set.
		1563	* @rmtoll CR1 START LL_I2C_GenerateStartCondition
		1564	* @param I2Cx I2C Instance.
		1565	* @retval None
		1566	*/
		1567	__STATIC_INLINE void LL_I2C_GenerateStartCondition(I2C_TypeDef *I2Cx)
		1568	{
		1569	SET_BIT(I2Cx->CR1, I2C_CR1_START);
		1570	}
		1571
		1572	/**
		1573	* @brief Generate a STOP condition after the current byte transfer (master mode).
		1574	* @rmtoll CR1 STOP LL_I2C_GenerateStopCondition
		1575	* @param I2Cx I2C Instance.
		1576	* @retval None
		1577	*/
		1578	__STATIC_INLINE void LL_I2C_GenerateStopCondition(I2C_TypeDef *I2Cx)
		1579	{
		1580	SET_BIT(I2Cx->CR1, I2C_CR1_STOP);
		1581	}
		1582
		1583	/**
		1584	* @brief Enable bit POS (master/host mode).
		1585	* @note In that case, the ACK bit controls the (N)ACK of the next byte received or the PEC bit indicates that the next byte in shift register is a PEC.
		1586	* @rmtoll CR1 POS LL_I2C_EnableBitPOS
		1587	* @param I2Cx I2C Instance.
		1588	* @retval None
		1589	*/
		1590	__STATIC_INLINE void LL_I2C_EnableBitPOS(I2C_TypeDef *I2Cx)
		1591	{
		1592	SET_BIT(I2Cx->CR1, I2C_CR1_POS);
		1593	}
		1594
		1595	/**
		1596	* @brief Disable bit POS (master/host mode).
		1597	* @note In that case, the ACK bit controls the (N)ACK of the current byte received or the PEC bit indicates that the current byte in shift register is a PEC.
		1598	* @rmtoll CR1 POS LL_I2C_DisableBitPOS
		1599	* @param I2Cx I2C Instance.
		1600	* @retval None
		1601	*/
		1602	__STATIC_INLINE void LL_I2C_DisableBitPOS(I2C_TypeDef *I2Cx)
		1603	{
		1604	CLEAR_BIT(I2Cx->CR1, I2C_CR1_POS);
		1605	}
		1606
		1607	/**
		1608	* @brief Check if bit POS is enabled or disabled.
		1609	* @rmtoll CR1 POS LL_I2C_IsEnabledBitPOS
		1610	* @param I2Cx I2C Instance.
		1611	* @retval State of bit (1 or 0).
		1612	*/
		1613	__STATIC_INLINE uint32_t LL_I2C_IsEnabledBitPOS(I2C_TypeDef *I2Cx)
		1614	{
		1615	return (READ_BIT(I2Cx->CR1, I2C_CR1_POS) == (I2C_CR1_POS));
		1616	}
		1617
		1618	/**
		1619	* @brief Indicate the value of transfer direction.
		1620	* @note RESET: Bus is in read transfer (peripheral point of view).
		1621	* SET: Bus is in write transfer (peripheral point of view).
		1622	* @rmtoll SR2 TRA LL_I2C_GetTransferDirection
		1623	* @param I2Cx I2C Instance.
		1624	* @retval Returned value can be one of the following values:
		1625	* @arg @ref LL_I2C_DIRECTION_WRITE
		1626	* @arg @ref LL_I2C_DIRECTION_READ
		1627	*/
		1628	__STATIC_INLINE uint32_t LL_I2C_GetTransferDirection(I2C_TypeDef *I2Cx)
		1629	{
		1630	return (uint32_t)(READ_BIT(I2Cx->SR2, I2C_SR2_TRA));
		1631	}
		1632
		1633	/**
		1634	* @brief Enable DMA last transfer.
		1635	* @note This action mean that next DMA EOT is the last transfer.
		1636	* @rmtoll CR2 LAST LL_I2C_EnableLastDMA
		1637	* @param I2Cx I2C Instance.
		1638	* @retval None
		1639	*/
		1640	__STATIC_INLINE void LL_I2C_EnableLastDMA(I2C_TypeDef *I2Cx)
		1641	{
		1642	SET_BIT(I2Cx->CR2, I2C_CR2_LAST);
		1643	}
		1644
		1645	/**
		1646	* @brief Disable DMA last transfer.
		1647	* @note This action mean that next DMA EOT is not the last transfer.
		1648	* @rmtoll CR2 LAST LL_I2C_DisableLastDMA
		1649	* @param I2Cx I2C Instance.
		1650	* @retval None
		1651	*/
		1652	__STATIC_INLINE void LL_I2C_DisableLastDMA(I2C_TypeDef *I2Cx)
		1653	{
		1654	CLEAR_BIT(I2Cx->CR2, I2C_CR2_LAST);
		1655	}
		1656
		1657	/**
		1658	* @brief Check if DMA last transfer is enabled or disabled.
		1659	* @rmtoll CR2 LAST LL_I2C_IsEnabledLastDMA
		1660	* @param I2Cx I2C Instance.
		1661	* @retval State of bit (1 or 0).
		1662	*/
		1663	__STATIC_INLINE uint32_t LL_I2C_IsEnabledLastDMA(I2C_TypeDef *I2Cx)
		1664	{
		1665	return (READ_BIT(I2Cx->CR2, I2C_CR2_LAST) == (I2C_CR2_LAST));
		1666	}
		1667
		1668	/**
		1669	* @brief Enable transfer or internal comparison of the SMBus Packet Error byte (transmission or reception mode).
		1670	* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
		1671	* SMBus feature is supported by the I2Cx Instance.
		1672	* @note This feature is cleared by hardware when the PEC byte is transferred or compared,
		1673	* or by a START or STOP condition, it is also cleared by software.
		1674	* @rmtoll CR1 PEC LL_I2C_EnableSMBusPECCompare
		1675	* @param I2Cx I2C Instance.
		1676	* @retval None
		1677	*/
		1678	__STATIC_INLINE void LL_I2C_EnableSMBusPECCompare(I2C_TypeDef *I2Cx)
		1679	{
		1680	SET_BIT(I2Cx->CR1, I2C_CR1_PEC);
		1681	}
		1682
		1683	/**
		1684	* @brief Disable transfer or internal comparison of the SMBus Packet Error byte (transmission or reception mode).
		1685	* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
		1686	* SMBus feature is supported by the I2Cx Instance.
		1687	* @rmtoll CR1 PEC LL_I2C_DisableSMBusPECCompare
		1688	* @param I2Cx I2C Instance.
		1689	* @retval None
		1690	*/
		1691	__STATIC_INLINE void LL_I2C_DisableSMBusPECCompare(I2C_TypeDef *I2Cx)
		1692	{
		1693	CLEAR_BIT(I2Cx->CR1, I2C_CR1_PEC);
		1694	}
		1695
		1696	/**
		1697	* @brief Check if the SMBus Packet Error byte transfer or internal comparison is requested or not.
		1698	* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
		1699	* SMBus feature is supported by the I2Cx Instance.
		1700	* @rmtoll CR1 PEC LL_I2C_IsEnabledSMBusPECCompare
		1701	* @param I2Cx I2C Instance.
		1702	* @retval State of bit (1 or 0).
		1703	*/
		1704	__STATIC_INLINE uint32_t LL_I2C_IsEnabledSMBusPECCompare(I2C_TypeDef *I2Cx)
		1705	{
		1706	return (READ_BIT(I2Cx->CR1, I2C_CR1_PEC) == (I2C_CR1_PEC));
		1707	}
		1708
		1709	/**
		1710	* @brief Get the SMBus Packet Error byte calculated.
		1711	* @note Macro @ref IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
		1712	* SMBus feature is supported by the I2Cx Instance.
		1713	* @rmtoll SR2 PEC LL_I2C_GetSMBusPEC
		1714	* @param I2Cx I2C Instance.
		1715	* @retval Value between Min_Data=0x00 and Max_Data=0xFF
		1716	*/
		1717	__STATIC_INLINE uint32_t LL_I2C_GetSMBusPEC(I2C_TypeDef *I2Cx)
		1718	{
		1719	return (uint32_t)(READ_BIT(I2Cx->SR2, I2C_SR2_PEC) >> I2C_SR2_PEC_Pos);
		1720	}
		1721
		1722	/**
		1723	* @brief Read Receive Data register.
		1724	* @rmtoll DR DR LL_I2C_ReceiveData8
		1725	* @param I2Cx I2C Instance.
		1726	* @retval Value between Min_Data=0x0 and Max_Data=0xFF
		1727	*/
		1728	__STATIC_INLINE uint8_t LL_I2C_ReceiveData8(I2C_TypeDef *I2Cx)
		1729	{
		1730	return (uint8_t)(READ_BIT(I2Cx->DR, I2C_DR_DR));
		1731	}
		1732
		1733	/**
		1734	* @brief Write in Transmit Data Register .
		1735	* @rmtoll DR DR LL_I2C_TransmitData8
		1736	* @param I2Cx I2C Instance.
		1737	* @param Data Value between Min_Data=0x0 and Max_Data=0xFF
		1738	* @retval None
		1739	*/
		1740	__STATIC_INLINE void LL_I2C_TransmitData8(I2C_TypeDef *I2Cx, uint8_t Data)
		1741	{
		1742	MODIFY_REG(I2Cx->DR, I2C_DR_DR, Data);
		1743	}
		1744
		1745	/**
		1746	* @}
		1747	*/
		1748
		1749	#if defined(USE_FULL_LL_DRIVER)
		1750	/** @defgroup I2C_LL_EF_Init Initialization and de-initialization functions
		1751	* @{
		1752	*/
		1753
		1754	uint32_t LL_I2C_Init(I2C_TypeDef I2Cx, LL_I2C_InitTypeDef I2C_InitStruct);
		1755	uint32_t LL_I2C_DeInit(I2C_TypeDef *I2Cx);
		1756	void LL_I2C_StructInit(LL_I2C_InitTypeDef *I2C_InitStruct);
		1757
		1758
		1759	/**
		1760	* @}
		1761	*/
		1762	#endif /* USE_FULL_LL_DRIVER */
		1763
		1764	/**
		1765	* @}
		1766	*/
		1767
		1768	/**
		1769	* @}
		1770	*/
		1771
		1772	#endif /* I2C1 \|\| I2C2 */
		1773
		1774	/**
		1775	* @}
		1776	*/
		1777
		1778	#ifdef __cplusplus
		1779	}
		1780	#endif
		1781
		1782	#endif /* __STM32F1xx_LL_I2C_H */
		1783
		1784	/********************** (C) COPYRIGHT STMicroelectronics *END OF FILE**/

Subversion Repositories LedShow

(root)/trunk/Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_ll_i2c.h – Rev 9