Subversion Repositories LedShow

/**

  ******************************************************************************

  * @file    stm32f1xx_hal_i2s.h

  * @author  MCD Application Team

  * @brief   Header file of I2S HAL module.

  ******************************************************************************

  * @attention

  *

  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.

  * All rights reserved.</center></h2>

  *

  * This software component is licensed by ST under BSD 3-Clause license,

  * the "License"; You may not use this file except in compliance with the

  * License. You may obtain a copy of the License at:

  *                        opensource.org/licenses/BSD-3-Clause

  *

  ******************************************************************************

  */

/* Define to prevent recursive inclusion -------------------------------------*/

#ifndef STM32F1xx_HAL_I2S_H

#define STM32F1xx_HAL_I2S_H

#ifdef __cplusplus

extern "C" {

#endif

/* Includes ------------------------------------------------------------------*/

#include "stm32f1xx_hal_def.h"

#if defined(SPI_I2S_SUPPORT)

/** @addtogroup STM32F1xx_HAL_Driver

  * @{

  */

/** @addtogroup I2S

  * @{

  */

/* Exported types ------------------------------------------------------------*/

/** @defgroup I2S_Exported_Types I2S Exported Types

  * @{

  */

/**

  * @brief I2S Init structure definition

  */

typedef struct

{

  uint32_t Mode;                /*!< Specifies the I2S operating mode.

                                     This parameter can be a value of @ref I2S_Mode */

  uint32_t Standard;            /*!< Specifies the standard used for the I2S communication.

                                     This parameter can be a value of @ref I2S_Standard */

  uint32_t DataFormat;          /*!< Specifies the data format for the I2S communication.

                                     This parameter can be a value of @ref I2S_Data_Format */

  uint32_t MCLKOutput;          /*!< Specifies whether the I2S MCLK output is enabled or not.

                                     This parameter can be a value of @ref I2S_MCLK_Output */

  uint32_t AudioFreq;           /*!< Specifies the frequency selected for the I2S communication.

                                     This parameter can be a value of @ref I2S_Audio_Frequency */

  uint32_t CPOL;                /*!< Specifies the idle state of the I2S clock.

                                     This parameter can be a value of @ref I2S_Clock_Polarity */

} I2S_InitTypeDef;

/**

  * @brief  HAL State structures definition

  */

typedef enum

{

  HAL_I2S_STATE_RESET      = 0x00U,  /*!< I2S not yet initialized or disabled                */

  HAL_I2S_STATE_READY      = 0x01U,  /*!< I2S initialized and ready for use                  */

  HAL_I2S_STATE_BUSY       = 0x02U,  /*!< I2S internal process is ongoing                    */

  HAL_I2S_STATE_BUSY_TX    = 0x03U,  /*!< Data Transmission process is ongoing               */

  HAL_I2S_STATE_BUSY_RX    = 0x04U,  /*!< Data Reception process is ongoing                  */

  HAL_I2S_STATE_TIMEOUT    = 0x06U,  /*!< I2S timeout state                                  */

  HAL_I2S_STATE_ERROR      = 0x07U   /*!< I2S error state                                    */

} HAL_I2S_StateTypeDef;

/**

  * @brief I2S handle Structure definition

  */

#if (USE_HAL_I2S_REGISTER_CALLBACKS == 1)

typedef struct __I2S_HandleTypeDef

#else

typedef struct

#endif /* USE_HAL_I2S_REGISTER_CALLBACKS */

{

  SPI_TypeDef                *Instance;    /*!< I2S registers base address */

  I2S_InitTypeDef            Init;         /*!< I2S communication parameters */

  uint16_t                   *pTxBuffPtr;  /*!< Pointer to I2S Tx transfer buffer */

  __IO uint16_t              TxXferSize;   /*!< I2S Tx transfer size */

  __IO uint16_t              TxXferCount;  /*!< I2S Tx transfer Counter */

  uint16_t                   *pRxBuffPtr;  /*!< Pointer to I2S Rx transfer buffer */

  __IO uint16_t              RxXferSize;   /*!< I2S Rx transfer size */

  __IO uint16_t              RxXferCount;  /*!< I2S Rx transfer counter

                                              (This field is initialized at the

                                               same value as transfer size at the

                                               beginning of the transfer and

                                               decremented when a sample is received

                                               NbSamplesReceived = RxBufferSize-RxBufferCount) */

  DMA_HandleTypeDef          *hdmatx;      /*!< I2S Tx DMA handle parameters */

  DMA_HandleTypeDef          *hdmarx;      /*!< I2S Rx DMA handle parameters */

  __IO HAL_LockTypeDef       Lock;         /*!< I2S locking object */

  __IO HAL_I2S_StateTypeDef  State;        /*!< I2S communication state */

  __IO uint32_t              ErrorCode;    /*!< I2S Error code

                                                This parameter can be a value of @ref I2S_Error */

#if (USE_HAL_I2S_REGISTER_CALLBACKS == 1U)

  void (* TxCpltCallback)(struct __I2S_HandleTypeDef *hi2s);             /*!< I2S Tx Completed callback          */

  void (* RxCpltCallback)(struct __I2S_HandleTypeDef *hi2s);             /*!< I2S Rx Completed callback          */

  void (* TxHalfCpltCallback)(struct __I2S_HandleTypeDef *hi2s);         /*!< I2S Tx Half Completed callback     */

  void (* RxHalfCpltCallback)(struct __I2S_HandleTypeDef *hi2s);         /*!< I2S Rx Half Completed callback     */

  void (* ErrorCallback)(struct __I2S_HandleTypeDef *hi2s);              /*!< I2S Error callback                 */

  void (* MspInitCallback)(struct __I2S_HandleTypeDef *hi2s);            /*!< I2S Msp Init callback              */

  void (* MspDeInitCallback)(struct __I2S_HandleTypeDef *hi2s);          /*!< I2S Msp DeInit callback            */

#endif  /* USE_HAL_I2S_REGISTER_CALLBACKS */

} I2S_HandleTypeDef;

#if (USE_HAL_I2S_REGISTER_CALLBACKS == 1U)

/**

  * @brief  HAL I2S Callback ID enumeration definition

  */

typedef enum

{

  HAL_I2S_TX_COMPLETE_CB_ID             = 0x00U,    /*!< I2S Tx Completed callback ID         */

  HAL_I2S_RX_COMPLETE_CB_ID             = 0x01U,    /*!< I2S Rx Completed callback ID         */

  HAL_I2S_TX_HALF_COMPLETE_CB_ID        = 0x03U,    /*!< I2S Tx Half Completed callback ID    */

  HAL_I2S_RX_HALF_COMPLETE_CB_ID        = 0x04U,    /*!< I2S Rx Half Completed callback ID    */

  HAL_I2S_ERROR_CB_ID                   = 0x06U,    /*!< I2S Error callback ID                */

  HAL_I2S_MSPINIT_CB_ID                 = 0x07U,    /*!< I2S Msp Init callback ID             */

  HAL_I2S_MSPDEINIT_CB_ID               = 0x08U     /*!< I2S Msp DeInit callback ID           */

} HAL_I2S_CallbackIDTypeDef;

/**

  * @brief  HAL I2S Callback pointer definition

  */

typedef  void (*pI2S_CallbackTypeDef)(I2S_HandleTypeDef *hi2s); /*!< pointer to an I2S callback function */

#endif /* USE_HAL_I2S_REGISTER_CALLBACKS */

/**

  * @}

  */

/* Exported constants --------------------------------------------------------*/

/** @defgroup I2S_Exported_Constants I2S Exported Constants

  * @{

  */

/** @defgroup I2S_Error I2S Error

  * @{

  */

#define HAL_I2S_ERROR_NONE               (0x00000000U)  /*!< No error                    */

#define HAL_I2S_ERROR_TIMEOUT            (0x00000001U)  /*!< Timeout error               */

#define HAL_I2S_ERROR_OVR                (0x00000002U)  /*!< OVR error                   */

#define HAL_I2S_ERROR_UDR                (0x00000004U)  /*!< UDR error                   */

#define HAL_I2S_ERROR_DMA                (0x00000008U)  /*!< DMA transfer error          */

#define HAL_I2S_ERROR_PRESCALER          (0x00000010U)  /*!< Prescaler Calculation error */

#if (USE_HAL_I2S_REGISTER_CALLBACKS == 1U)

#define HAL_I2S_ERROR_INVALID_CALLBACK   (0x00000020U)  /*!< Invalid Callback error      */

#endif /* USE_HAL_I2S_REGISTER_CALLBACKS */

#define HAL_I2S_ERROR_BUSY_LINE_RX       (0x00000040U)  /*!< Busy Rx Line error          */

/**

  * @}

  */

/** @defgroup I2S_Mode I2S Mode

  * @{

  */

#define I2S_MODE_SLAVE_TX                (0x00000000U)

#define I2S_MODE_SLAVE_RX                (SPI_I2SCFGR_I2SCFG_0)

#define I2S_MODE_MASTER_TX               (SPI_I2SCFGR_I2SCFG_1)

#define I2S_MODE_MASTER_RX               ((SPI_I2SCFGR_I2SCFG_0 | SPI_I2SCFGR_I2SCFG_1))

/**

  * @}

  */

/** @defgroup I2S_Standard I2S Standard

  * @{

  */

#define I2S_STANDARD_PHILIPS             (0x00000000U)

#define I2S_STANDARD_MSB                 (SPI_I2SCFGR_I2SSTD_0)

#define I2S_STANDARD_LSB                 (SPI_I2SCFGR_I2SSTD_1)

#define I2S_STANDARD_PCM_SHORT           ((SPI_I2SCFGR_I2SSTD_0 | SPI_I2SCFGR_I2SSTD_1))

#define I2S_STANDARD_PCM_LONG            ((SPI_I2SCFGR_I2SSTD_0 | SPI_I2SCFGR_I2SSTD_1 | SPI_I2SCFGR_PCMSYNC))

/**

  * @}

  */

/** @defgroup I2S_Data_Format I2S Data Format

  * @{

  */

#define I2S_DATAFORMAT_16B               (0x00000000U)

#define I2S_DATAFORMAT_16B_EXTENDED      (SPI_I2SCFGR_CHLEN)

#define I2S_DATAFORMAT_24B               ((SPI_I2SCFGR_CHLEN | SPI_I2SCFGR_DATLEN_0))

#define I2S_DATAFORMAT_32B               ((SPI_I2SCFGR_CHLEN | SPI_I2SCFGR_DATLEN_1))

/**

  * @}

  */

/** @defgroup I2S_MCLK_Output I2S MCLK Output

  * @{

  */

#define I2S_MCLKOUTPUT_ENABLE            (SPI_I2SPR_MCKOE)

#define I2S_MCLKOUTPUT_DISABLE           (0x00000000U)

/**

  * @}

  */

/** @defgroup I2S_Audio_Frequency I2S Audio Frequency

  * @{

  */

#define I2S_AUDIOFREQ_192K               (192000U)

#define I2S_AUDIOFREQ_96K                (96000U)

#define I2S_AUDIOFREQ_48K                (48000U)

#define I2S_AUDIOFREQ_44K                (44100U)

#define I2S_AUDIOFREQ_32K                (32000U)

#define I2S_AUDIOFREQ_22K                (22050U)

#define I2S_AUDIOFREQ_16K                (16000U)

#define I2S_AUDIOFREQ_11K                (11025U)

#define I2S_AUDIOFREQ_8K                 (8000U)

#define I2S_AUDIOFREQ_DEFAULT            (2U)

/**

  * @}

  */

/** @defgroup I2S_Clock_Polarity I2S Clock Polarity

  * @{

  */

#define I2S_CPOL_LOW                     (0x00000000U)

#define I2S_CPOL_HIGH                    (SPI_I2SCFGR_CKPOL)

/**

  * @}

  */

/** @defgroup I2S_Interrupts_Definition I2S Interrupts Definition

  * @{

  */

#define I2S_IT_TXE                       SPI_CR2_TXEIE

#define I2S_IT_RXNE                      SPI_CR2_RXNEIE

#define I2S_IT_ERR                       SPI_CR2_ERRIE

/**

  * @}

  */

/** @defgroup I2S_Flags_Definition I2S Flags Definition

  * @{

  */

#define I2S_FLAG_TXE                     SPI_SR_TXE

#define I2S_FLAG_RXNE                    SPI_SR_RXNE

#define I2S_FLAG_UDR                     SPI_SR_UDR

#define I2S_FLAG_OVR                     SPI_SR_OVR

#define I2S_FLAG_FRE                     SPI_SR_FRE

#define I2S_FLAG_CHSIDE                  SPI_SR_CHSIDE

#define I2S_FLAG_BSY                     SPI_SR_BSY

#define I2S_FLAG_MASK                   (SPI_SR_RXNE\

                                         | SPI_SR_TXE | SPI_SR_UDR | SPI_SR_OVR | SPI_SR_CHSIDE | SPI_SR_BSY)

/**

  * @}

  */

/**

  * @}

  */

/* Exported macros -----------------------------------------------------------*/

/** @defgroup I2S_Exported_macros I2S Exported Macros

  * @{

  */

/** @brief  Reset I2S handle state

  * @param  __HANDLE__ specifies the I2S Handle.

  * @retval None

  */

#if (USE_HAL_I2S_REGISTER_CALLBACKS == 1U)

#define __HAL_I2S_RESET_HANDLE_STATE(__HANDLE__)                do{                                                  \

                                                                    (__HANDLE__)->State = HAL_I2S_STATE_RESET;       \

                                                                    (__HANDLE__)->MspInitCallback = NULL;            \

                                                                    (__HANDLE__)->MspDeInitCallback = NULL;          \

                                                                  } while(0)

#else

#define __HAL_I2S_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_I2S_STATE_RESET)

#endif /* USE_HAL_I2S_REGISTER_CALLBACKS */

/** @brief  Enable the specified SPI peripheral (in I2S mode).

  * @param  __HANDLE__ specifies the I2S Handle.

  * @retval None

  */

#define __HAL_I2S_ENABLE(__HANDLE__)    (SET_BIT((__HANDLE__)->Instance->I2SCFGR, SPI_I2SCFGR_I2SE))

/** @brief  Disable the specified SPI peripheral (in I2S mode).

  * @param  __HANDLE__ specifies the I2S Handle.

  * @retval None

  */

#define __HAL_I2S_DISABLE(__HANDLE__) (CLEAR_BIT((__HANDLE__)->Instance->I2SCFGR, SPI_I2SCFGR_I2SE))

/** @brief  Enable the specified I2S interrupts.

  * @param  __HANDLE__ specifies the I2S Handle.

  * @param  __INTERRUPT__ specifies the interrupt source to enable or disable.

  *         This parameter can be one of the following values:

  *            @arg I2S_IT_TXE: Tx buffer empty interrupt enable

  *            @arg I2S_IT_RXNE: RX buffer not empty interrupt enable

  *            @arg I2S_IT_ERR: Error interrupt enable

  * @retval None

  */

#define __HAL_I2S_ENABLE_IT(__HANDLE__, __INTERRUPT__)    (SET_BIT((__HANDLE__)->Instance->CR2,(__INTERRUPT__)))

/** @brief  Disable the specified I2S interrupts.

  * @param  __HANDLE__ specifies the I2S Handle.

  * @param  __INTERRUPT__ specifies the interrupt source to enable or disable.

  *         This parameter can be one of the following values:

  *            @arg I2S_IT_TXE: Tx buffer empty interrupt enable

  *            @arg I2S_IT_RXNE: RX buffer not empty interrupt enable

  *            @arg I2S_IT_ERR: Error interrupt enable

  * @retval None

  */

#define __HAL_I2S_DISABLE_IT(__HANDLE__, __INTERRUPT__) (CLEAR_BIT((__HANDLE__)->Instance->CR2,(__INTERRUPT__)))

/** @brief  Checks if the specified I2S interrupt source is enabled or disabled.

  * @param  __HANDLE__ specifies the I2S Handle.

  *         This parameter can be I2S where x: 1, 2, or 3 to select the I2S peripheral.

  * @param  __INTERRUPT__ specifies the I2S interrupt source to check.

  *          This parameter can be one of the following values:

  *            @arg I2S_IT_TXE: Tx buffer empty interrupt enable

  *            @arg I2S_IT_RXNE: RX buffer not empty interrupt enable

  *            @arg I2S_IT_ERR: Error interrupt enable

  * @retval The new state of __IT__ (TRUE or FALSE).

  */

#define __HAL_I2S_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((__HANDLE__)->Instance->CR2\

                                                              & (__INTERRUPT__)) == (__INTERRUPT__)) ? SET : RESET)

/** @brief  Checks whether the specified I2S flag is set or not.

  * @param  __HANDLE__ specifies the I2S Handle.

  * @param  __FLAG__ specifies the flag to check.

  *         This parameter can be one of the following values:

  *            @arg I2S_FLAG_RXNE: Receive buffer not empty flag

  *            @arg I2S_FLAG_TXE: Transmit buffer empty flag

  *            @arg I2S_FLAG_UDR: Underrun flag

  *            @arg I2S_FLAG_OVR: Overrun flag

  *            @arg I2S_FLAG_FRE: Frame error flag

  *            @arg I2S_FLAG_CHSIDE: Channel Side flag

  *            @arg I2S_FLAG_BSY: Busy flag

  * @retval The new state of __FLAG__ (TRUE or FALSE).

  */

#define __HAL_I2S_GET_FLAG(__HANDLE__, __FLAG__) ((((__HANDLE__)->Instance->SR) & (__FLAG__)) == (__FLAG__))

/** @brief Clears the I2S OVR pending flag.

  * @param  __HANDLE__ specifies the I2S Handle.

  * @retval None

  */

#define __HAL_I2S_CLEAR_OVRFLAG(__HANDLE__) do{ \

                                                __IO uint32_t tmpreg_ovr = 0x00U; \

                                                tmpreg_ovr = (__HANDLE__)->Instance->DR; \

                                                tmpreg_ovr = (__HANDLE__)->Instance->SR; \

                                                UNUSED(tmpreg_ovr); \

                                              }while(0U)

/** @brief Clears the I2S UDR pending flag.

  * @param  __HANDLE__ specifies the I2S Handle.

  * @retval None

  */

#define __HAL_I2S_CLEAR_UDRFLAG(__HANDLE__) do{\

                                                __IO uint32_t tmpreg_udr = 0x00U;\

                                                tmpreg_udr = ((__HANDLE__)->Instance->SR);\

                                                UNUSED(tmpreg_udr); \

                                              }while(0U)

/** @brief Flush the I2S DR Register.

  * @param  __HANDLE__ specifies the I2S Handle.

  * @retval None

  */

#define __HAL_I2S_FLUSH_RX_DR(__HANDLE__)  do{\

                                                __IO uint32_t tmpreg_dr = 0x00U;\

                                                tmpreg_dr = ((__HANDLE__)->Instance->DR);\

                                                UNUSED(tmpreg_dr); \

                                              }while(0U)

/**

  * @}

  */

/* Exported functions --------------------------------------------------------*/

/** @addtogroup I2S_Exported_Functions

  * @{

  */

/** @addtogroup I2S_Exported_Functions_Group1

  * @{

  */

/* Initialization/de-initialization functions  ********************************/

HAL_StatusTypeDef HAL_I2S_Init(I2S_HandleTypeDef *hi2s);

HAL_StatusTypeDef HAL_I2S_DeInit(I2S_HandleTypeDef *hi2s);

void HAL_I2S_MspInit(I2S_HandleTypeDef *hi2s);

void HAL_I2S_MspDeInit(I2S_HandleTypeDef *hi2s);

/* Callbacks Register/UnRegister functions  ***********************************/

#if (USE_HAL_I2S_REGISTER_CALLBACKS == 1U)

HAL_StatusTypeDef HAL_I2S_RegisterCallback(I2S_HandleTypeDef *hi2s, HAL_I2S_CallbackIDTypeDef CallbackID,

                                           pI2S_CallbackTypeDef pCallback);

HAL_StatusTypeDef HAL_I2S_UnRegisterCallback(I2S_HandleTypeDef *hi2s, HAL_I2S_CallbackIDTypeDef CallbackID);

#endif /* USE_HAL_I2S_REGISTER_CALLBACKS */

/**

  * @}

  */

/** @addtogroup I2S_Exported_Functions_Group2

  * @{

  */

/* I/O operation functions  ***************************************************/

/* Blocking mode: Polling */

HAL_StatusTypeDef HAL_I2S_Transmit(I2S_HandleTypeDef *hi2s, uint16_t *pData, uint16_t Size, uint32_t Timeout);

HAL_StatusTypeDef HAL_I2S_Receive(I2S_HandleTypeDef *hi2s, uint16_t *pData, uint16_t Size, uint32_t Timeout);

/* Non-Blocking mode: Interrupt */

HAL_StatusTypeDef HAL_I2S_Transmit_IT(I2S_HandleTypeDef *hi2s, uint16_t *pData, uint16_t Size);

HAL_StatusTypeDef HAL_I2S_Receive_IT(I2S_HandleTypeDef *hi2s, uint16_t *pData, uint16_t Size);

void HAL_I2S_IRQHandler(I2S_HandleTypeDef *hi2s);

/* Non-Blocking mode: DMA */

HAL_StatusTypeDef HAL_I2S_Transmit_DMA(I2S_HandleTypeDef *hi2s, uint16_t *pData, uint16_t Size);

HAL_StatusTypeDef HAL_I2S_Receive_DMA(I2S_HandleTypeDef *hi2s, uint16_t *pData, uint16_t Size);

HAL_StatusTypeDef HAL_I2S_DMAPause(I2S_HandleTypeDef *hi2s);

HAL_StatusTypeDef HAL_I2S_DMAResume(I2S_HandleTypeDef *hi2s);

HAL_StatusTypeDef HAL_I2S_DMAStop(I2S_HandleTypeDef *hi2s);

/* Callbacks used in non blocking modes (Interrupt and DMA) *******************/

void HAL_I2S_TxHalfCpltCallback(I2S_HandleTypeDef *hi2s);

void HAL_I2S_TxCpltCallback(I2S_HandleTypeDef *hi2s);

void HAL_I2S_RxHalfCpltCallback(I2S_HandleTypeDef *hi2s);

void HAL_I2S_RxCpltCallback(I2S_HandleTypeDef *hi2s);

void HAL_I2S_ErrorCallback(I2S_HandleTypeDef *hi2s);

/**

  * @}

  */

/** @addtogroup I2S_Exported_Functions_Group3

  * @{

  */

/* Peripheral Control and State functions  ************************************/

HAL_I2S_StateTypeDef HAL_I2S_GetState(I2S_HandleTypeDef *hi2s);

uint32_t HAL_I2S_GetError(I2S_HandleTypeDef *hi2s);

/**

  * @}

  */

/**

  * @}

  */

/* Private types -------------------------------------------------------------*/

/* Private variables ---------------------------------------------------------*/

/* Private constants ---------------------------------------------------------*/

/* Private macros ------------------------------------------------------------*/

/** @defgroup I2S_Private_Macros I2S Private Macros

  * @{

  */

/** @brief  Check whether the specified SPI flag is set or not.

  * @param  __SR__  copy of I2S SR register.

  * @param  __FLAG__ specifies the flag to check.

  *         This parameter can be one of the following values:

  *            @arg I2S_FLAG_RXNE: Receive buffer not empty flag

  *            @arg I2S_FLAG_TXE: Transmit buffer empty flag

  *            @arg I2S_FLAG_UDR: Underrun error flag

  *            @arg I2S_FLAG_OVR: Overrun flag

  *            @arg I2S_FLAG_CHSIDE: Channel side flag

  *            @arg I2S_FLAG_BSY: Busy flag

  * @retval SET or RESET.

  */

#define I2S_CHECK_FLAG(__SR__, __FLAG__)         ((((__SR__)\

                                                    & ((__FLAG__) & I2S_FLAG_MASK)) == ((__FLAG__) & I2S_FLAG_MASK)) ? SET : RESET)

/** @brief  Check whether the specified SPI Interrupt is set or not.

  * @param  __CR2__  copy of I2S CR2 register.

  * @param  __INTERRUPT__ specifies the SPI interrupt source to check.

  *         This parameter can be one of the following values:

  *            @arg I2S_IT_TXE: Tx buffer empty interrupt enable

  *            @arg I2S_IT_RXNE: RX buffer not empty interrupt enable

  *            @arg I2S_IT_ERR: Error interrupt enable

  * @retval SET or RESET.

  */

#define I2S_CHECK_IT_SOURCE(__CR2__, __INTERRUPT__)      ((((__CR2__)\

                                                            & (__INTERRUPT__)) == (__INTERRUPT__)) ? SET : RESET)

/** @brief  Checks if I2S Mode parameter is in allowed range.

  * @param  __MODE__ specifies the I2S Mode.

  *         This parameter can be a value of @ref I2S_Mode

  * @retval None

  */

#define IS_I2S_MODE(__MODE__) (((__MODE__) == I2S_MODE_SLAVE_TX)  || \

                               ((__MODE__) == I2S_MODE_SLAVE_RX)  || \

                               ((__MODE__) == I2S_MODE_MASTER_TX) || \

                               ((__MODE__) == I2S_MODE_MASTER_RX))

#define IS_I2S_STANDARD(__STANDARD__) (((__STANDARD__) == I2S_STANDARD_PHILIPS)   || \

                                       ((__STANDARD__) == I2S_STANDARD_MSB)       || \

                                       ((__STANDARD__) == I2S_STANDARD_LSB)       || \

                                       ((__STANDARD__) == I2S_STANDARD_PCM_SHORT) || \

                                       ((__STANDARD__) == I2S_STANDARD_PCM_LONG))

#define IS_I2S_DATA_FORMAT(__FORMAT__) (((__FORMAT__) == I2S_DATAFORMAT_16B)          || \

                                        ((__FORMAT__) == I2S_DATAFORMAT_16B_EXTENDED) || \

                                        ((__FORMAT__) == I2S_DATAFORMAT_24B)          || \

                                        ((__FORMAT__) == I2S_DATAFORMAT_32B))

#define IS_I2S_MCLK_OUTPUT(__OUTPUT__) (((__OUTPUT__) == I2S_MCLKOUTPUT_ENABLE) || \

                                        ((__OUTPUT__) == I2S_MCLKOUTPUT_DISABLE))

#define IS_I2S_AUDIO_FREQ(__FREQ__) ((((__FREQ__) >= I2S_AUDIOFREQ_8K)    && \

                                      ((__FREQ__) <= I2S_AUDIOFREQ_192K)) || \

                                     ((__FREQ__) == I2S_AUDIOFREQ_DEFAULT))

/** @brief  Checks if I2S Serial clock steady state parameter is in allowed range.

  * @param  __CPOL__ specifies the I2S serial clock steady state.

  *         This parameter can be a value of @ref I2S_Clock_Polarity

  * @retval None

  */

#define IS_I2S_CPOL(__CPOL__) (((__CPOL__) == I2S_CPOL_LOW) || \

                               ((__CPOL__) == I2S_CPOL_HIGH))

/**

  * @}

  */

/**

  * @}

  */

/**

  * @}

  */

#endif /* SPI_I2S_SUPPORT */

#ifdef __cplusplus

}

#endif

#endif /* STM32F1xx_HAL_I2S_H */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/