Subversion Repositories DashDisplay

/**

  ******************************************************************************

  * @file    stm32f1xx_hal_conf.h

  * @author  MCD Application Team

  * @version V1.0.4

  * @date    29-April-2016

  * @brief   HAL configuration template file.

  *          This file should be copied to the application folder and renamed

  *          to stm32f1xx_hal_conf.h.

  ******************************************************************************

  * @attention

  *

  * <h2><center>&copy; COPYRIGHT(c) 2016 STMicroelectronics</center></h2>

  *

  * Redistribution and use in source and binary forms, with or without modification,

  * are permitted provided that the following conditions are met:

  *   1. Redistributions of source code must retain the above copyright notice,

  *      this list of conditions and the following disclaimer.

  *   2. Redistributions in binary form must reproduce the above copyright notice,

  *      this list of conditions and the following disclaimer in the documentation

  *      and/or other materials provided with the distribution.

  *   3. Neither the name of STMicroelectronics nor the names of its contributors

  *      may be used to endorse or promote products derived from this software

  *      without specific prior written permission.

  *

  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"

  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE

  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE

  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR

  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER

  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,

  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE

  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

  *

  ******************************************************************************

  */

/* Define to prevent recursive inclusion -------------------------------------*/

#ifndef __STM32F1xx_HAL_CONF_H

#define __STM32F1xx_HAL_CONF_H

#ifdef __cplusplus

 extern "C" {

#endif

/* Exported types ------------------------------------------------------------*/

/* Exported constants --------------------------------------------------------*/

/* ########################## Module Selection ############################## */

/**

  * @brief This is the list of modules to be used in the HAL driver

  */

#define HAL_MODULE_ENABLED

#define HAL_ADC_MODULE_ENABLED

#define HAL_CAN_MODULE_ENABLED

#define HAL_CEC_MODULE_ENABLED

#define HAL_CORTEX_MODULE_ENABLED

#define HAL_CRC_MODULE_ENABLED

#define HAL_DAC_MODULE_ENABLED

#define HAL_DMA_MODULE_ENABLED

#define HAL_ETH_MODULE_ENABLED

#define HAL_FLASH_MODULE_ENABLED

#define HAL_GPIO_MODULE_ENABLED

#define HAL_HCD_MODULE_ENABLED

#define HAL_I2C_MODULE_ENABLED

#define HAL_I2S_MODULE_ENABLED

#define HAL_IRDA_MODULE_ENABLED

#define HAL_IWDG_MODULE_ENABLED

#define HAL_NAND_MODULE_ENABLED

#define HAL_NOR_MODULE_ENABLED

#define HAL_PCCARD_MODULE_ENABLED

#define HAL_PCD_MODULE_ENABLED

#define HAL_PWR_MODULE_ENABLED

#define HAL_RCC_MODULE_ENABLED

#define HAL_RTC_MODULE_ENABLED

#define HAL_SD_MODULE_ENABLED

#define HAL_SMARTCARD_MODULE_ENABLED

#define HAL_SPI_MODULE_ENABLED

#define HAL_SRAM_MODULE_ENABLED

#define HAL_TIM_MODULE_ENABLED

#define HAL_UART_MODULE_ENABLED

#define HAL_USART_MODULE_ENABLED

#define HAL_WWDG_MODULE_ENABLED

/* ########################## Oscillator Values adaptation ####################*/

/**

  * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.

  *        This value is used by the RCC HAL module to compute the system frequency

  *        (when HSE is used as system clock source, directly or through the PLL).  

  */

#if !defined  (HSE_VALUE) 

#if defined(USE_STM3210C_EVAL)

  #define HSE_VALUE    ((uint32_t)25000000) /*!< Value of the External oscillator in Hz */

#else

  #define HSE_VALUE    ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */

#endif

#endif /* HSE_VALUE */

#if !defined  (HSE_STARTUP_TIMEOUT)

  #define HSE_STARTUP_TIMEOUT    ((uint32_t)100)   /*!< Time out for HSE start up, in ms */

#endif /* HSE_STARTUP_TIMEOUT */

/**

  * @brief Internal High Speed oscillator (HSI) value.

  *        This value is used by the RCC HAL module to compute the system frequency

  *        (when HSI is used as system clock source, directly or through the PLL).

  */

#if !defined  (HSI_VALUE)

  #define HSI_VALUE    ((uint32_t)8000000) /*!< Value of the Internal oscillator in Hz*/

#endif /* HSI_VALUE */

/**

  * @brief External Low Speed oscillator (LSE) value.

  *        This value is used by the UART, RTC HAL module to compute the system frequency

  */

#if !defined  (LSE_VALUE)

  #define LSE_VALUE    ((uint32_t)32768) /*!< Value of the External oscillator in Hz*/

#endif /* LSE_VALUE */

#if !defined  (LSE_STARTUP_TIMEOUT)

  #define LSE_STARTUP_TIMEOUT    ((uint32_t)5000)   /*!< Time out for LSE start up, in ms */

#endif /* HSE_STARTUP_TIMEOUT */

/* Tip: To avoid modifying this file each time you need to use different HSE,

   ===  you can define the HSE value in your toolchain compiler preprocessor. */

/* ########################### System Configuration ######################### */

/**

  * @brief This is the HAL system configuration section

  */    

#define  VDD_VALUE                    ((uint32_t)3300) /*!< Value of VDD in mv */           

#define  TICK_INT_PRIORITY            ((uint32_t)0x000F)    /*!< tick interrupt priority */            

#define  USE_RTOS                     0     

#define  PREFETCH_ENABLE              1

/* ########################## Assert Selection ############################## */

/**

  * @brief Uncomment the line below to expanse the "assert_param" macro in the

  *        HAL drivers code

  */

/*#define USE_FULL_ASSERT    1*/

/* ################## Ethernet peripheral configuration ##################### */

/* Section 1 : Ethernet peripheral configuration */

/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */

#define MAC_ADDR0   2

#define MAC_ADDR1   0

#define MAC_ADDR2   0

#define MAC_ADDR3   0

#define MAC_ADDR4   0

#define MAC_ADDR5   0

/* Definition of the Ethernet driver buffers size and count */  

#define ETH_RX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for receive               */

#define ETH_TX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for transmit              */

#define ETH_RXBUFNB                    ((uint32_t)8)       /* 4 Rx buffers of size ETH_RX_BUF_SIZE  */

#define ETH_TXBUFNB                    ((uint32_t)4)       /* 4 Tx buffers of size ETH_TX_BUF_SIZE  */

/* Section 2: PHY configuration section */

/* DP83848 PHY Address*/

#define DP83848_PHY_ADDRESS             0x01

/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/

#define PHY_RESET_DELAY                 ((uint32_t)0x000000FF)

/* PHY Configuration delay */

#define PHY_CONFIG_DELAY                ((uint32_t)0x00000FFF)

#define PHY_READ_TO                     ((uint32_t)0x0000FFFF)

#define PHY_WRITE_TO                    ((uint32_t)0x0000FFFF)

/* Section 3: Common PHY Registers */

#define PHY_BCR                         ((uint16_t)0x00)    /*!< Transceiver Basic Control Register   */

#define PHY_BSR                         ((uint16_t)0x01)    /*!< Transceiver Basic Status Register    */

#define PHY_RESET                       ((uint16_t)0x8000)  /*!< PHY Reset */

#define PHY_LOOPBACK                    ((uint16_t)0x4000)  /*!< Select loop-back mode */

#define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100)  /*!< Set the full-duplex mode at 100 Mb/s */

#define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000)  /*!< Set the half-duplex mode at 100 Mb/s */

#define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100)  /*!< Set the full-duplex mode at 10 Mb/s  */

#define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000)  /*!< Set the half-duplex mode at 10 Mb/s  */

#define PHY_AUTONEGOTIATION             ((uint16_t)0x1000)  /*!< Enable auto-negotiation function     */

#define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200)  /*!< Restart auto-negotiation function    */

#define PHY_POWERDOWN                   ((uint16_t)0x0800)  /*!< Select the power down mode           */

#define PHY_ISOLATE                     ((uint16_t)0x0400)  /*!< Isolate PHY from MII                 */

#define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020)  /*!< Auto-Negotiation process completed   */

#define PHY_LINKED_STATUS               ((uint16_t)0x0004)  /*!< Valid link established               */

#define PHY_JABBER_DETECTION            ((uint16_t)0x0002)  /*!< Jabber condition detected            */

/* Section 4: Extended PHY Registers */

#define PHY_SR                          ((uint16_t)0x10)    /*!< PHY status register Offset                      */

#define PHY_MICR                        ((uint16_t)0x11)    /*!< MII Interrupt Control Register                  */

#define PHY_MISR                        ((uint16_t)0x12)    /*!< MII Interrupt Status and Misc. Control Register */

#define PHY_LINK_STATUS                 ((uint16_t)0x0001)  /*!< PHY Link mask                                   */

#define PHY_SPEED_STATUS                ((uint16_t)0x0002)  /*!< PHY Speed mask                                  */

#define PHY_DUPLEX_STATUS               ((uint16_t)0x0004)  /*!< PHY Duplex mask                                 */

#define PHY_MICR_INT_EN                 ((uint16_t)0x0002)  /*!< PHY Enable interrupts                           */

#define PHY_MICR_INT_OE                 ((uint16_t)0x0001)  /*!< PHY Enable output interrupt events              */

#define PHY_MISR_LINK_INT_EN            ((uint16_t)0x0020)  /*!< Enable Interrupt on change of link status       */

#define PHY_LINK_INTERRUPT              ((uint16_t)0x2000)  /*!< PHY link status interrupt mask                  */

/* Includes ------------------------------------------------------------------*/

/**

  * @brief Include module's header file

  */

#ifdef HAL_RCC_MODULE_ENABLED

 #include "stm32f1xx_hal_rcc.h"

#endif /* HAL_RCC_MODULE_ENABLED */

#ifdef HAL_GPIO_MODULE_ENABLED

 #include "stm32f1xx_hal_gpio.h"

#endif /* HAL_GPIO_MODULE_ENABLED */

#ifdef HAL_DMA_MODULE_ENABLED

  #include "stm32f1xx_hal_dma.h"

#endif /* HAL_DMA_MODULE_ENABLED */

#ifdef HAL_ETH_MODULE_ENABLED

  #include "stm32f1xx_hal_eth.h"

#endif /* HAL_ETH_MODULE_ENABLED */  

#ifdef HAL_CAN_MODULE_ENABLED

 #include "stm32f1xx_hal_can.h"

#endif /* HAL_CAN_MODULE_ENABLED */

#ifdef HAL_CEC_MODULE_ENABLED

 #include "stm32f1xx_hal_cec.h"

#endif /* HAL_CEC_MODULE_ENABLED */

#ifdef HAL_CORTEX_MODULE_ENABLED

 #include "stm32f1xx_hal_cortex.h"

#endif /* HAL_CORTEX_MODULE_ENABLED */

#ifdef HAL_ADC_MODULE_ENABLED

 #include "stm32f1xx_hal_adc.h"

#endif /* HAL_ADC_MODULE_ENABLED */

#ifdef HAL_CRC_MODULE_ENABLED

 #include "stm32f1xx_hal_crc.h"

#endif /* HAL_CRC_MODULE_ENABLED */

#ifdef HAL_DAC_MODULE_ENABLED

 #include "stm32f1xx_hal_dac.h"

#endif /* HAL_DAC_MODULE_ENABLED */

#ifdef HAL_FLASH_MODULE_ENABLED

 #include "stm32f1xx_hal_flash.h"

#endif /* HAL_FLASH_MODULE_ENABLED */

#ifdef HAL_SRAM_MODULE_ENABLED

 #include "stm32f1xx_hal_sram.h"

#endif /* HAL_SRAM_MODULE_ENABLED */

#ifdef HAL_NOR_MODULE_ENABLED

 #include "stm32f1xx_hal_nor.h"

#endif /* HAL_NOR_MODULE_ENABLED */

#ifdef HAL_I2C_MODULE_ENABLED

 #include "stm32f1xx_hal_i2c.h"

#endif /* HAL_I2C_MODULE_ENABLED */

#ifdef HAL_I2S_MODULE_ENABLED

 #include "stm32f1xx_hal_i2s.h"

#endif /* HAL_I2S_MODULE_ENABLED */

#ifdef HAL_IWDG_MODULE_ENABLED

 #include "stm32f1xx_hal_iwdg.h"

#endif /* HAL_IWDG_MODULE_ENABLED */

#ifdef HAL_PWR_MODULE_ENABLED

 #include "stm32f1xx_hal_pwr.h"

#endif /* HAL_PWR_MODULE_ENABLED */

#ifdef HAL_RTC_MODULE_ENABLED

 #include "stm32f1xx_hal_rtc.h"

#endif /* HAL_RTC_MODULE_ENABLED */

#ifdef HAL_PCCARD_MODULE_ENABLED

 #include "stm32f1xx_hal_pccard.h"

#endif /* HAL_PCCARD_MODULE_ENABLED */ 

#ifdef HAL_SD_MODULE_ENABLED

 #include "stm32f1xx_hal_sd.h"

#endif /* HAL_SD_MODULE_ENABLED */  

#ifdef HAL_NAND_MODULE_ENABLED

 #include "stm32f1xx_hal_nand.h"

#endif /* HAL_NAND_MODULE_ENABLED */     

#ifdef HAL_SPI_MODULE_ENABLED

 #include "stm32f1xx_hal_spi.h"

#endif /* HAL_SPI_MODULE_ENABLED */

#ifdef HAL_TIM_MODULE_ENABLED

 #include "stm32f1xx_hal_tim.h"

#endif /* HAL_TIM_MODULE_ENABLED */

#ifdef HAL_UART_MODULE_ENABLED

 #include "stm32f1xx_hal_uart.h"

#endif /* HAL_UART_MODULE_ENABLED */

#ifdef HAL_USART_MODULE_ENABLED

 #include "stm32f1xx_hal_usart.h"

#endif /* HAL_USART_MODULE_ENABLED */

#ifdef HAL_IRDA_MODULE_ENABLED

 #include "stm32f1xx_hal_irda.h"

#endif /* HAL_IRDA_MODULE_ENABLED */

#ifdef HAL_SMARTCARD_MODULE_ENABLED

 #include "stm32f1xx_hal_smartcard.h"

#endif /* HAL_SMARTCARD_MODULE_ENABLED */

#ifdef HAL_WWDG_MODULE_ENABLED

 #include "stm32f1xx_hal_wwdg.h"

#endif /* HAL_WWDG_MODULE_ENABLED */

#ifdef HAL_PCD_MODULE_ENABLED

 #include "stm32f1xx_hal_pcd.h"

#endif /* HAL_PCD_MODULE_ENABLED */

#ifdef HAL_HCD_MODULE_ENABLED

 #include "stm32f1xx_hal_hcd.h"

#endif /* HAL_HCD_MODULE_ENABLED */   

/* Exported macro ------------------------------------------------------------*/

#ifdef  USE_FULL_ASSERT

/**

  * @brief  The assert_param macro is used for function's parameters check.

  * @param  expr: If expr is false, it calls assert_failed function

  *         which reports the name of the source file and the source

  *         line number of the call that failed.

  *         If expr is true, it returns no value.

  * @retval None

  */

  #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))

/* Exported functions ------------------------------------------------------- */

  void assert_failed(uint8_t* file, uint32_t line);

#else

  #define assert_param(expr) ((void)0)

#endif /* USE_FULL_ASSERT */

#ifdef __cplusplus

}

#endif

#endif /* __STM32F1xx_HAL_CONF_H */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/