Subversion Repositories testOled

/**

  ******************************************************************************

  * @file    stm32f1xx_hal_can_legacy.h

  * @author  MCD Application Team

  * @brief   Header file of CAN HAL module.

  ******************************************************************************

  * @attention

  *

  * <h2><center>&copy; COPYRIGHT(c) 2017 STMicroelectronics</center></h2>

  *

  * Redistribution and use in source and binary forms, with or without modification,

  * are permitted provided that the following conditions are met:

  *   1. Redistributions of source code must retain the above copyright notice,

  *      this list of conditions and the following disclaimer.

  *   2. Redistributions in binary form must reproduce the above copyright notice,

  *      this list of conditions and the following disclaimer in the documentation

  *      and/or other materials provided with the distribution.

  *   3. Neither the name of STMicroelectronics nor the names of its contributors

  *      may be used to endorse or promote products derived from this software

  *      without specific prior written permission.

  *

  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"

  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE

  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE

  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR

  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER

  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,

  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE

  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

  *

  ******************************************************************************

  */

/* Define to prevent recursive inclusion -------------------------------------*/

#ifndef __STM32F1xx_HAL_CAN_LEGACY_H

#define __STM32F1xx_HAL_CAN_LEGACY_H

#ifdef __cplusplus

 extern "C" {

#endif

#if defined(STM32F103x6) || defined(STM32F103xB) || defined(STM32F103xE) || \

    defined(STM32F103xG) || defined(STM32F105xC) || defined(STM32F107xC)

/* Includes ------------------------------------------------------------------*/

#include "stm32f1xx_hal_def.h"

/** @addtogroup STM32F1xx_HAL_Driver

  * @{

  */

/** @addtogroup CAN

  * @{

  */

/* Exported types ------------------------------------------------------------*/

/** @defgroup CAN_Exported_Types CAN Exported Types

  * @{

  */

/**

  * @brief  HAL State structures definition

  */

typedef enum

{

  HAL_CAN_STATE_RESET             = 0x00U,  /*!< CAN not yet initialized or disabled */

  HAL_CAN_STATE_READY             = 0x01U,  /*!< CAN initialized and ready for use   */

  HAL_CAN_STATE_BUSY              = 0x02U,  /*!< CAN process is ongoing              */

  HAL_CAN_STATE_BUSY_TX           = 0x12U,  /*!< CAN process is ongoing              */

  HAL_CAN_STATE_BUSY_RX0          = 0x22U,  /*!< CAN process is ongoing              */

  HAL_CAN_STATE_BUSY_RX1          = 0x32U,  /*!< CAN process is ongoing              */

  HAL_CAN_STATE_BUSY_TX_RX0       = 0x42U,  /*!< CAN process is ongoing              */

  HAL_CAN_STATE_BUSY_TX_RX1       = 0x52U,  /*!< CAN process is ongoing              */

  HAL_CAN_STATE_BUSY_RX0_RX1      = 0x62U,  /*!< CAN process is ongoing              */

  HAL_CAN_STATE_BUSY_TX_RX0_RX1   = 0x72U,  /*!< CAN process is ongoing              */

  HAL_CAN_STATE_TIMEOUT           = 0x03U,  /*!< CAN in Timeout state                */

  HAL_CAN_STATE_ERROR             = 0x04U   /*!< CAN error state                     */

}HAL_CAN_StateTypeDef;

/**

  * @brief  CAN init structure definition

  */

typedef struct

{

  uint32_t Prescaler;  /*!< Specifies the length of a time quantum.

                            This parameter must be a number between Min_Data = 1 and Max_Data = 1024 */

  uint32_t Mode;       /*!< Specifies the CAN operating mode.

                            This parameter can be a value of @ref CAN_operating_mode */

  uint32_t SJW;        /*!< Specifies the maximum number of time quanta

                            the CAN hardware is allowed to lengthen or

                            shorten a bit to perform resynchronization.

                            This parameter can be a value of @ref CAN_synchronisation_jump_width */

  uint32_t BS1;        /*!< Specifies the number of time quanta in Bit Segment 1.

                            This parameter can be a value of @ref CAN_time_quantum_in_bit_segment_1 */

  uint32_t BS2;        /*!< Specifies the number of time quanta in Bit Segment 2.

                            This parameter can be a value of @ref CAN_time_quantum_in_bit_segment_2 */

  uint32_t TTCM;       /*!< Enable or disable the time triggered communication mode.

                            This parameter can be set to ENABLE or DISABLE. */

  uint32_t ABOM;       /*!< Enable or disable the automatic bus-off management.

                            This parameter can be set to ENABLE or DISABLE */

  uint32_t AWUM;       /*!< Enable or disable the automatic wake-up mode.

                            This parameter can be set to ENABLE or DISABLE */

  uint32_t NART;       /*!< Enable or disable the non-automatic retransmission mode.

                            This parameter can be set to ENABLE or DISABLE */

  uint32_t RFLM;       /*!< Enable or disable the receive FIFO Locked mode.

                            This parameter can be set to ENABLE or DISABLE */

  uint32_t TXFP;       /*!< Enable or disable the transmit FIFO priority.

                            This parameter can be set to ENABLE or DISABLE */

}CAN_InitTypeDef;

/**

  * @brief  CAN Tx message structure definition  

  */

typedef struct

{

  uint32_t StdId;    /*!< Specifies the standard identifier.

                          This parameter must be a number between Min_Data = 0 and Max_Data = 0x7FF */

  uint32_t ExtId;    /*!< Specifies the extended identifier.

                          This parameter must be a number between Min_Data = 0 and Max_Data = 0x1FFFFFFF */

  uint32_t IDE;      /*!< Specifies the type of identifier for the message that will be transmitted.

                          This parameter can be a value of @ref CAN_Identifier_Type */

  uint32_t RTR;      /*!< Specifies the type of frame for the message that will be transmitted.

                          This parameter can be a value of @ref CAN_remote_transmission_request */

  uint32_t DLC;      /*!< Specifies the length of the frame that will be transmitted.

                          This parameter must be a number between Min_Data = 0 and Max_Data = 8 */

  uint8_t Data[8];   /*!< Contains the data to be transmitted.

                          This parameter must be a number between Min_Data = 0 and Max_Data = 0xFF */

}CanTxMsgTypeDef;

/**

  * @brief  CAN Rx message structure definition

  */

typedef struct

{

  uint32_t StdId;       /*!< Specifies the standard identifier.

                             This parameter must be a number between Min_Data = 0 and Max_Data = 0x7FF */

  uint32_t ExtId;       /*!< Specifies the extended identifier.

                             This parameter must be a number between Min_Data = 0 and Max_Data = 0x1FFFFFFF */

  uint32_t IDE;         /*!< Specifies the type of identifier for the message that will be received.

                             This parameter can be a value of @ref CAN_Identifier_Type */

  uint32_t RTR;         /*!< Specifies the type of frame for the received message.

                             This parameter can be a value of @ref CAN_remote_transmission_request */

  uint32_t DLC;         /*!< Specifies the length of the frame that will be received.

                             This parameter must be a number between Min_Data = 0 and Max_Data = 8 */

  uint8_t Data[8];      /*!< Contains the data to be received.

                             This parameter must be a number between Min_Data = 0 and Max_Data = 0xFF */

  uint32_t FMI;         /*!< Specifies the index of the filter the message stored in the mailbox passes through.

                             This parameter must be a number between Min_Data = 0 and Max_Data = 0xFF */

  uint32_t FIFONumber;  /*!< Specifies the receive FIFO number.

                             This parameter can be CAN_FIFO0 or CAN_FIFO1 */

}CanRxMsgTypeDef;

/**

  * @brief  CAN handle Structure definition

  */

typedef struct

{

  CAN_TypeDef                 *Instance;  /*!< Register base address          */

  CAN_InitTypeDef             Init;       /*!< CAN required parameters        */

  CanTxMsgTypeDef*            pTxMsg;     /*!< Pointer to transmit structure  */

  CanRxMsgTypeDef*            pRxMsg;     /*!< Pointer to reception structure for RX FIFO0 msg */

  CanRxMsgTypeDef*            pRx1Msg;    /*!< Pointer to reception structure for RX FIFO1 msg */

  __IO HAL_CAN_StateTypeDef   State;      /*!< CAN communication state        */

  HAL_LockTypeDef             Lock;       /*!< CAN locking object             */

  __IO uint32_t               ErrorCode;  /*!< CAN Error code                 */

}CAN_HandleTypeDef;

/**

  * @}

  */

/* Exported constants --------------------------------------------------------*/

/** @defgroup CAN_Exported_Constants CAN Exported Constants

  * @{

  */

/** @defgroup CAN_Error_Code CAN Error Code

  * @{

  */

#define   HAL_CAN_ERROR_NONE      0x00000000U    /*!< No error             */

#define   HAL_CAN_ERROR_EWG       0x00000001U    /*!< EWG error            */

#define   HAL_CAN_ERROR_EPV       0x00000002U    /*!< EPV error            */

#define   HAL_CAN_ERROR_BOF       0x00000004U    /*!< BOF error            */

#define   HAL_CAN_ERROR_STF       0x00000008U    /*!< Stuff error          */

#define   HAL_CAN_ERROR_FOR       0x00000010U    /*!< Form error           */

#define   HAL_CAN_ERROR_ACK       0x00000020U    /*!< Acknowledgment error */

#define   HAL_CAN_ERROR_BR        0x00000040U    /*!< Bit recessive        */

#define   HAL_CAN_ERROR_BD        0x00000080U    /*!< LEC dominant         */

#define   HAL_CAN_ERROR_CRC       0x00000100U    /*!< LEC transfer error   */

#define   HAL_CAN_ERROR_FOV0      0x00000200U    /*!< FIFO0 overrun error  */

#define   HAL_CAN_ERROR_FOV1      0x00000400U    /*!< FIFO1 overrun error  */

#define   HAL_CAN_ERROR_TXFAIL    0x00000800U    /*!< Transmit failure     */

/**

  * @}

  */

/** @defgroup CAN_InitStatus CAN initialization Status

  * @{

  */

#define CAN_INITSTATUS_FAILED       0x00000000U  /*!< CAN initialization failed */

#define CAN_INITSTATUS_SUCCESS      0x00000001U  /*!< CAN initialization OK */

/**

  * @}

  */

/** @defgroup CAN_operating_mode CAN Operating Mode

  * @{

  */

#define CAN_MODE_NORMAL             0x00000000U                                /*!< Normal mode   */

#define CAN_MODE_LOOPBACK           ((uint32_t)CAN_BTR_LBKM)                   /*!< Loopback mode */

#define CAN_MODE_SILENT             ((uint32_t)CAN_BTR_SILM)                   /*!< Silent mode   */

#define CAN_MODE_SILENT_LOOPBACK    ((uint32_t)(CAN_BTR_LBKM | CAN_BTR_SILM))  /*!< Loopback combined with silent mode */

/**

  * @}

  */

/** @defgroup CAN_synchronisation_jump_width CAN Synchronization Jump Width

  * @{

  */

#define CAN_SJW_1TQ                 0x00000000U                /*!< 1 time quantum */

#define CAN_SJW_2TQ                 ((uint32_t)CAN_BTR_SJW_0)  /*!< 2 time quantum */

#define CAN_SJW_3TQ                 ((uint32_t)CAN_BTR_SJW_1)  /*!< 3 time quantum */

#define CAN_SJW_4TQ                 ((uint32_t)CAN_BTR_SJW)    /*!< 4 time quantum */

/**

  * @}

  */

/** @defgroup CAN_time_quantum_in_bit_segment_1 CAN Time Quantum in Bit Segment 1

  * @{

  */

#define CAN_BS1_1TQ                 0x00000000U                                                  /*!< 1 time quantum  */

#define CAN_BS1_2TQ                 ((uint32_t)CAN_BTR_TS1_0)                                    /*!< 2 time quantum  */

#define CAN_BS1_3TQ                 ((uint32_t)CAN_BTR_TS1_1)                                    /*!< 3 time quantum  */

#define CAN_BS1_4TQ                 ((uint32_t)(CAN_BTR_TS1_1 | CAN_BTR_TS1_0))                  /*!< 4 time quantum  */

#define CAN_BS1_5TQ                 ((uint32_t)CAN_BTR_TS1_2)                                    /*!< 5 time quantum  */

#define CAN_BS1_6TQ                 ((uint32_t)(CAN_BTR_TS1_2 | CAN_BTR_TS1_0))                  /*!< 6 time quantum  */

#define CAN_BS1_7TQ                 ((uint32_t)(CAN_BTR_TS1_2 | CAN_BTR_TS1_1))                  /*!< 7 time quantum  */

#define CAN_BS1_8TQ                 ((uint32_t)(CAN_BTR_TS1_2 | CAN_BTR_TS1_1 | CAN_BTR_TS1_0))  /*!< 8 time quantum  */

#define CAN_BS1_9TQ                 ((uint32_t)CAN_BTR_TS1_3)                                    /*!< 9 time quantum  */

#define CAN_BS1_10TQ                ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_0))                  /*!< 10 time quantum */

#define CAN_BS1_11TQ                ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_1))                  /*!< 11 time quantum */

#define CAN_BS1_12TQ                ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_1 | CAN_BTR_TS1_0))  /*!< 12 time quantum */

#define CAN_BS1_13TQ                ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_2))                  /*!< 13 time quantum */

#define CAN_BS1_14TQ                ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_2 | CAN_BTR_TS1_0))  /*!< 14 time quantum */

#define CAN_BS1_15TQ                ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_2 | CAN_BTR_TS1_1))  /*!< 15 time quantum */

#define CAN_BS1_16TQ                ((uint32_t)CAN_BTR_TS1) /*!< 16 time quantum */

/**

  * @}

  */

/** @defgroup CAN_time_quantum_in_bit_segment_2 CAN Time Quantum in bit segment 2

  * @{

  */

#define CAN_BS2_1TQ                 0x00000000U                                  /*!< 1 time quantum */

#define CAN_BS2_2TQ                 ((uint32_t)CAN_BTR_TS2_0)                    /*!< 2 time quantum */

#define CAN_BS2_3TQ                 ((uint32_t)CAN_BTR_TS2_1)                    /*!< 3 time quantum */

#define CAN_BS2_4TQ                 ((uint32_t)(CAN_BTR_TS2_1 | CAN_BTR_TS2_0))  /*!< 4 time quantum */

#define CAN_BS2_5TQ                 ((uint32_t)CAN_BTR_TS2_2)                    /*!< 5 time quantum */

#define CAN_BS2_6TQ                 ((uint32_t)(CAN_BTR_TS2_2 | CAN_BTR_TS2_0))  /*!< 6 time quantum */

#define CAN_BS2_7TQ                 ((uint32_t)(CAN_BTR_TS2_2 | CAN_BTR_TS2_1))  /*!< 7 time quantum */

#define CAN_BS2_8TQ                 ((uint32_t)CAN_BTR_TS2)                      /*!< 8 time quantum */

/**

  * @}

  */

/** @defgroup CAN_filter_mode  CAN Filter Mode

  * @{

  */

#define CAN_FILTERMODE_IDMASK       ((uint8_t)0x00)  /*!< Identifier mask mode */

#define CAN_FILTERMODE_IDLIST       ((uint8_t)0x01)  /*!< Identifier list mode */

/**

  * @}

  */

/** @defgroup CAN_filter_scale CAN Filter Scale

  * @{

  */

#define CAN_FILTERSCALE_16BIT       ((uint8_t)0x00)  /*!< Two 16-bit filters */

#define CAN_FILTERSCALE_32BIT       ((uint8_t)0x01)  /*!< One 32-bit filter  */

/**

  * @}

  */

/** @defgroup CAN_filter_FIFO CAN Filter FIFO

  * @{

  */

#define CAN_FILTER_FIFO0             ((uint8_t)0x00)  /*!< Filter FIFO 0 assignment for filter x */

#define CAN_FILTER_FIFO1             ((uint8_t)0x01)  /*!< Filter FIFO 1 assignment for filter x */

/**

  * @}

  */

/** @defgroup CAN_Identifier_Type CAN Identifier Type

  * @{

  */

#define CAN_ID_STD                  0x00000000U  /*!< Standard Id */

#define CAN_ID_EXT                  0x00000004U  /*!< Extended Id */

/**

  * @}

  */

/** @defgroup CAN_remote_transmission_request CAN Remote Transmission Request

  * @{

  */

#define CAN_RTR_DATA                0x00000000U  /*!< Data frame */

#define CAN_RTR_REMOTE              0x00000002U  /*!< Remote frame */

/**

  * @}

  */

/** @defgroup CAN_transmit_constants CAN Transmit Constants

  * @{

  */

#define CAN_TXSTATUS_NOMAILBOX      ((uint8_t)0x04)  /*!< CAN cell did not provide CAN_TxStatus_NoMailBox */

/**

  * @}

  */

/** @defgroup CAN_receive_FIFO_number_constants CAN Receive FIFO Number

  * @{

  */

#define CAN_FIFO0                   ((uint8_t)0x00)  /*!< CAN FIFO 0 used to receive */

#define CAN_FIFO1                   ((uint8_t)0x01)  /*!< CAN FIFO 1 used to receive */

/**

  * @}

  */

/** @defgroup CAN_flags CAN Flags

  * @{

  */

/* If the flag is 0x3XXXXXXX, it means that it can be used with CAN_GetFlagStatus()

   and CAN_ClearFlag() functions. */

/* If the flag is 0x1XXXXXXX, it means that it can only be used with

   CAN_GetFlagStatus() function.  */

/* Transmit Flags */

#define CAN_FLAG_RQCP0             ((uint32_t)((TSR_REGISTER_INDEX << 8U) | CAN_TSR_RQCP0_BIT_POSITION))  /*!< Request MailBox0 flag         */

#define CAN_FLAG_RQCP1             ((uint32_t)((TSR_REGISTER_INDEX << 8U) | CAN_TSR_RQCP1_BIT_POSITION))  /*!< Request MailBox1 flag         */

#define CAN_FLAG_RQCP2             ((uint32_t)((TSR_REGISTER_INDEX << 8U) | CAN_TSR_RQCP2_BIT_POSITION))  /*!< Request MailBox2 flag         */

#define CAN_FLAG_TXOK0             ((uint32_t)((TSR_REGISTER_INDEX << 8U) | CAN_TSR_TXOK0_BIT_POSITION))  /*!< Transmission OK MailBox0 flag */

#define CAN_FLAG_TXOK1             ((uint32_t)((TSR_REGISTER_INDEX << 8U) | CAN_TSR_TXOK1_BIT_POSITION))  /*!< Transmission OK MailBox1 flag */

#define CAN_FLAG_TXOK2             ((uint32_t)((TSR_REGISTER_INDEX << 8U) | CAN_TSR_TXOK2_BIT_POSITION))  /*!< Transmission OK MailBox2 flag */

#define CAN_FLAG_TME0              ((uint32_t)((TSR_REGISTER_INDEX << 8U) | CAN_TSR_TME0_BIT_POSITION))   /*!< Transmit mailbox 0 empty flag */

#define CAN_FLAG_TME1              ((uint32_t)((TSR_REGISTER_INDEX << 8U) | CAN_TSR_TME1_BIT_POSITION))   /*!< Transmit mailbox 0 empty flag */

#define CAN_FLAG_TME2              ((uint32_t)((TSR_REGISTER_INDEX << 8U) | CAN_TSR_TME2_BIT_POSITION))   /*!< Transmit mailbox 0 empty flag */

/* Receive Flags */

#define CAN_FLAG_FF0               ((uint32_t)((RF0R_REGISTER_INDEX << 8U) | CAN_RF0R_FF0_BIT_POSITION))  /*!< FIFO 0 Full flag    */

#define CAN_FLAG_FOV0              ((uint32_t)((RF0R_REGISTER_INDEX << 8U) | CAN_RF0R_FOV0_BIT_POSITION)) /*!< FIFO 0 Overrun flag */

#define CAN_FLAG_FF1               ((uint32_t)((RF1R_REGISTER_INDEX << 8U) | CAN_RF1R_FF1_BIT_POSITION))  /*!< FIFO 1 Full flag    */

#define CAN_FLAG_FOV1              ((uint32_t)((RF1R_REGISTER_INDEX << 8U) | CAN_RF1R_FOV1_BIT_POSITION)) /*!< FIFO 1 Overrun flag */

/* Operating Mode Flags */

#define CAN_FLAG_WKU               ((uint32_t)((MSR_REGISTER_INDEX << 8U) | CAN_MSR_WKU_BIT_POSITION))    /*!< Wake up flag           */

#define CAN_FLAG_SLAK              ((uint32_t)((MSR_REGISTER_INDEX << 8U) | CAN_MSR_SLAK_BIT_POSITION))   /*!< Sleep acknowledge flag */

#define CAN_FLAG_SLAKI             ((uint32_t)((MSR_REGISTER_INDEX << 8U) | CAN_MSR_SLAKI_BIT_POSITION))  /*!< Sleep acknowledge flag */

/* @note When SLAK interrupt is disabled (SLKIE=0), no polling on SLAKI is possible.

         In this case the SLAK bit can be polled.*/

/* Error Flags */

#define CAN_FLAG_EWG               ((uint32_t)((ESR_REGISTER_INDEX << 8U) | CAN_ESR_EWG_BIT_POSITION))    /*!< Error warning flag   */

#define CAN_FLAG_EPV               ((uint32_t)((ESR_REGISTER_INDEX << 8U) | CAN_ESR_EPV_BIT_POSITION))    /*!< Error passive flag   */

#define CAN_FLAG_BOF               ((uint32_t)((ESR_REGISTER_INDEX << 8U) | CAN_ESR_BOF_BIT_POSITION))    /*!< Bus-Off flag         */

/**

  * @}

  */

/** @defgroup CAN_Interrupts CAN Interrupts

  * @{

  */

#define CAN_IT_TME                  ((uint32_t)CAN_IER_TMEIE)   /*!< Transmit mailbox empty interrupt */

/* Receive Interrupts */

#define CAN_IT_FMP0                 ((uint32_t)CAN_IER_FMPIE0)  /*!< FIFO 0 message pending interrupt */

#define CAN_IT_FF0                  ((uint32_t)CAN_IER_FFIE0)   /*!< FIFO 0 full interrupt            */

#define CAN_IT_FOV0                 ((uint32_t)CAN_IER_FOVIE0)  /*!< FIFO 0 overrun interrupt         */

#define CAN_IT_FMP1                 ((uint32_t)CAN_IER_FMPIE1)  /*!< FIFO 1 message pending interrupt */

#define CAN_IT_FF1                  ((uint32_t)CAN_IER_FFIE1)   /*!< FIFO 1 full interrupt            */

#define CAN_IT_FOV1                 ((uint32_t)CAN_IER_FOVIE1)  /*!< FIFO 1 overrun interrupt         */

/* Operating Mode Interrupts */

#define CAN_IT_WKU                  ((uint32_t)CAN_IER_WKUIE)  /*!< Wake-up interrupt           */

#define CAN_IT_SLK                  ((uint32_t)CAN_IER_SLKIE)  /*!< Sleep acknowledge interrupt */

/* Error Interrupts */

#define CAN_IT_EWG                  ((uint32_t)CAN_IER_EWGIE) /*!< Error warning interrupt   */

#define CAN_IT_EPV                  ((uint32_t)CAN_IER_EPVIE) /*!< Error passive interrupt   */

#define CAN_IT_BOF                  ((uint32_t)CAN_IER_BOFIE) /*!< Bus-off interrupt         */

#define CAN_IT_LEC                  ((uint32_t)CAN_IER_LECIE) /*!< Last error code interrupt */

#define CAN_IT_ERR                  ((uint32_t)CAN_IER_ERRIE) /*!< Error Interrupt           */

/**

  * @}

  */

/**

  * @}

  */

/** @defgroup CAN_Private_Constants CAN Private Constants

  * @{

  */

/* CAN intermediate shift values used for CAN flags */

#define TSR_REGISTER_INDEX      0x5U

#define RF0R_REGISTER_INDEX     0x2U

#define RF1R_REGISTER_INDEX     0x4U

#define MSR_REGISTER_INDEX      0x1U

#define ESR_REGISTER_INDEX      0x3U

/* CAN flags bits position into their respective register (TSR, RF0R, RF1R or MSR regsiters) */

/* Transmit Flags */

#define CAN_TSR_RQCP0_BIT_POSITION     0x00000000U

#define CAN_TSR_RQCP1_BIT_POSITION     0x00000008U

#define CAN_TSR_RQCP2_BIT_POSITION     0x00000010U

#define CAN_TSR_TXOK0_BIT_POSITION     0x00000001U

#define CAN_TSR_TXOK1_BIT_POSITION     0x00000009U

#define CAN_TSR_TXOK2_BIT_POSITION     0x00000011U

#define CAN_TSR_TME0_BIT_POSITION      0x0000001AU

#define CAN_TSR_TME1_BIT_POSITION      0x0000001BU

#define CAN_TSR_TME2_BIT_POSITION      0x0000001CU

/* Receive Flags */

#define CAN_RF0R_FF0_BIT_POSITION      0x00000003U

#define CAN_RF0R_FOV0_BIT_POSITION     0x00000004U

#define CAN_RF1R_FF1_BIT_POSITION      0x00000003U

#define CAN_RF1R_FOV1_BIT_POSITION     0x00000004U

/* Operating Mode Flags */

#define CAN_MSR_WKU_BIT_POSITION       0x00000003U

#define CAN_MSR_SLAK_BIT_POSITION      0x00000001U

#define CAN_MSR_SLAKI_BIT_POSITION     0x00000004U

/* Error Flags */

#define CAN_ESR_EWG_BIT_POSITION       0x00000000U

#define CAN_ESR_EPV_BIT_POSITION       0x00000001U

#define CAN_ESR_BOF_BIT_POSITION       0x00000002U

/* Mask used by macro to get/clear CAN flags*/

#define CAN_FLAG_MASK                  0x000000FFU

/* Mailboxes definition */

#define CAN_TXMAILBOX_0   ((uint8_t)0x00)

#define CAN_TXMAILBOX_1   ((uint8_t)0x01)

#define CAN_TXMAILBOX_2   ((uint8_t)0x02)

/**

  * @}

  */

/* Exported macros -----------------------------------------------------------*/

/** @defgroup CAN_Exported_Macros CAN Exported Macros

  * @{

  */

/** @brief  Reset CAN handle state

  * @param  __HANDLE__: CAN handle.

  * @retval None

  */

#define __HAL_CAN_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_CAN_STATE_RESET)

/**

  * @brief  Enable the specified CAN interrupts

  * @param  __HANDLE__: CAN handle.

  * @param  __INTERRUPT__: CAN Interrupt.

  *         This parameter can be one of the following values:

  *            @arg CAN_IT_TME: Transmit mailbox empty interrupt enable

  *            @arg CAN_IT_FMP0: FIFO 0 message pending interrupt

  *            @arg CAN_IT_FF0 : FIFO 0 full interrupt

  *            @arg CAN_IT_FOV0: FIFO 0 overrun interrupt

  *            @arg CAN_IT_FMP1: FIFO 1 message pending interrupt

  *            @arg CAN_IT_FF1 : FIFO 1 full interrupt

  *            @arg CAN_IT_FOV1: FIFO 1 overrun interrupt

  *            @arg CAN_IT_WKU : Wake-up interrupt

  *            @arg CAN_IT_SLK : Sleep acknowledge interrupt

  *            @arg CAN_IT_EWG : Error warning interrupt

  *            @arg CAN_IT_EPV : Error passive interrupt

  *            @arg CAN_IT_BOF : Bus-off interrupt

  *            @arg CAN_IT_LEC : Last error code interrupt

  *            @arg CAN_IT_ERR : Error Interrupt

  * @retval None.

  */

#define __HAL_CAN_ENABLE_IT(__HANDLE__, __INTERRUPT__) (((__HANDLE__)->Instance->IER) |= (__INTERRUPT__))

/**

  * @brief  Disable the specified CAN interrupts

  * @param  __HANDLE__: CAN handle.

  * @param  __INTERRUPT__: CAN Interrupt.

  *         This parameter can be one of the following values:

  *            @arg CAN_IT_TME: Transmit mailbox empty interrupt enable

  *            @arg CAN_IT_FMP0: FIFO 0 message pending interrupt

  *            @arg CAN_IT_FF0 : FIFO 0 full interrupt

  *            @arg CAN_IT_FOV0: FIFO 0 overrun interrupt

  *            @arg CAN_IT_FMP1: FIFO 1 message pending interrupt

  *            @arg CAN_IT_FF1 : FIFO 1 full interrupt

  *            @arg CAN_IT_FOV1: FIFO 1 overrun interrupt

  *            @arg CAN_IT_WKU : Wake-up interrupt

  *            @arg CAN_IT_SLK : Sleep acknowledge interrupt

  *            @arg CAN_IT_EWG : Error warning interrupt

  *            @arg CAN_IT_EPV : Error passive interrupt

  *            @arg CAN_IT_BOF : Bus-off interrupt

  *            @arg CAN_IT_LEC : Last error code interrupt

  *            @arg CAN_IT_ERR : Error Interrupt

  * @retval None.

  */

#define __HAL_CAN_DISABLE_IT(__HANDLE__, __INTERRUPT__) (((__HANDLE__)->Instance->IER) &= ~(__INTERRUPT__))

/**

  * @brief  Return the number of pending received messages.

  * @param  __HANDLE__: CAN handle.

  * @param  __FIFONUMBER__: Receive FIFO number, CAN_FIFO0 or CAN_FIFO1.

  * @retval The number of pending message.

  */

#define __HAL_CAN_MSG_PENDING(__HANDLE__, __FIFONUMBER__) (((__FIFONUMBER__) == CAN_FIFO0)? \

((uint8_t)((__HANDLE__)->Instance->RF0R & 0x03U)) : ((uint8_t)((__HANDLE__)->Instance->RF1R & 0x03U)))

/** @brief  Check whether the specified CAN flag is set or not.

  * @param  __HANDLE__: specifies the CAN Handle.

  * @param  __FLAG__: specifies the flag to check.

  *         This parameter can be one of the following values:

  *            @arg CAN_TSR_RQCP0: Request MailBox0 Flag

  *            @arg CAN_TSR_RQCP1: Request MailBox1 Flag

  *            @arg CAN_TSR_RQCP2: Request MailBox2 Flag

  *            @arg CAN_FLAG_TXOK0: Transmission OK MailBox0 Flag

  *            @arg CAN_FLAG_TXOK1: Transmission OK MailBox1 Flag

  *            @arg CAN_FLAG_TXOK2: Transmission OK MailBox2 Flag

  *            @arg CAN_FLAG_TME0: Transmit mailbox 0 empty Flag

  *            @arg CAN_FLAG_TME1: Transmit mailbox 1 empty Flag

  *            @arg CAN_FLAG_TME2: Transmit mailbox 2 empty Flag

  *            @arg CAN_FLAG_FMP0: FIFO 0 Message Pending Flag

  *            @arg CAN_FLAG_FF0: FIFO 0 Full Flag

  *            @arg CAN_FLAG_FOV0: FIFO 0 Overrun Flag

  *            @arg CAN_FLAG_FMP1: FIFO 1 Message Pending Flag

  *            @arg CAN_FLAG_FF1: FIFO 1 Full Flag

  *            @arg CAN_FLAG_FOV1: FIFO 1 Overrun Flag

  *            @arg CAN_FLAG_WKU: Wake up Flag

  *            @arg CAN_FLAG_SLAK: Sleep acknowledge Flag

  *            @arg CAN_FLAG_SLAKI: Sleep acknowledge Flag

  *            @arg CAN_FLAG_EWG: Error Warning Flag

  *            @arg CAN_FLAG_EPV: Error Passive Flag

  *            @arg CAN_FLAG_BOF: Bus-Off Flag

  * @retval The new state of __FLAG__ (TRUE or FALSE).

  */

#define __HAL_CAN_GET_FLAG(__HANDLE__, __FLAG__) \

((((__FLAG__) >> 8U) == 5U)? ((((__HANDLE__)->Instance->TSR) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \

 (((__FLAG__) >> 8U) == 2U)? ((((__HANDLE__)->Instance->RF0R) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \

 (((__FLAG__) >> 8U) == 4U)? ((((__HANDLE__)->Instance->RF1R) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \

 (((__FLAG__) >> 8U) == 1U)? ((((__HANDLE__)->Instance->MSR) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \

 ((((__HANDLE__)->Instance->ESR) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))))

/** @brief  Clear the specified CAN pending flag.

  * @param  __HANDLE__: specifies the CAN Handle.

  * @param  __FLAG__: specifies the flag to check.

  *         This parameter can be one of the following values:

  *            @arg CAN_TSR_RQCP0: Request MailBox0 Flag

  *            @arg CAN_TSR_RQCP1: Request MailBox1 Flag

  *            @arg CAN_TSR_RQCP2: Request MailBox2 Flag

  *            @arg CAN_FLAG_TXOK0: Transmission OK MailBox0 Flag

  *            @arg CAN_FLAG_TXOK1: Transmission OK MailBox1 Flag

  *            @arg CAN_FLAG_TXOK2: Transmission OK MailBox2 Flag

  *            @arg CAN_FLAG_TME0: Transmit mailbox 0 empty Flag

  *            @arg CAN_FLAG_TME1: Transmit mailbox 1 empty Flag

  *            @arg CAN_FLAG_TME2: Transmit mailbox 2 empty Flag

  *            @arg CAN_FLAG_FMP0: FIFO 0 Message Pending Flag

  *            @arg CAN_FLAG_FF0: FIFO 0 Full Flag

  *            @arg CAN_FLAG_FOV0: FIFO 0 Overrun Flag

  *            @arg CAN_FLAG_FMP1: FIFO 1 Message Pending Flag

  *            @arg CAN_FLAG_FF1: FIFO 1 Full Flag

  *            @arg CAN_FLAG_FOV1: FIFO 1 Overrun Flag

  *            @arg CAN_FLAG_WKU: Wake up Flag

  *            @arg CAN_FLAG_SLAKI: Sleep acknowledge Flag

  * @retval The new state of __FLAG__ (TRUE or FALSE).

  */

#define __HAL_CAN_CLEAR_FLAG(__HANDLE__, __FLAG__) \

((((__FLAG__) >> 8U) == TSR_REGISTER_INDEX) ? (((__HANDLE__)->Instance->TSR)  = (1U << ((__FLAG__) & CAN_FLAG_MASK))): \

 (((__FLAG__) >> 8U) == RF0R_REGISTER_INDEX)? (((__HANDLE__)->Instance->RF0R) = (1U << ((__FLAG__) & CAN_FLAG_MASK))): \

 (((__FLAG__) >> 8U) == RF1R_REGISTER_INDEX)? (((__HANDLE__)->Instance->RF1R) = (1U << ((__FLAG__) & CAN_FLAG_MASK))): \

 (((__FLAG__) >> 8U) == MSR_REGISTER_INDEX) ? (((__HANDLE__)->Instance->MSR)  = (1U << ((__FLAG__) & CAN_FLAG_MASK))): 0U)

/** @brief  Check if the specified CAN interrupt source is enabled or disabled.

  * @param  __HANDLE__: specifies the CAN Handle.

  * @param  __INTERRUPT__: specifies the CAN interrupt source to check.

  *         This parameter can be one of the following values:

  *            @arg CAN_IT_TME: Transmit mailbox empty interrupt enable

  *            @arg CAN_IT_FMP0: FIFO 0 message pending interrupt

  *            @arg CAN_IT_FF0 : FIFO 0 full interrupt

  *            @arg CAN_IT_FOV0: FIFO 0 overrun interrupt

  *            @arg CAN_IT_FMP1: FIFO 1 message pending interrupt

  *            @arg CAN_IT_FF1 : FIFO 1 full interrupt

  *            @arg CAN_IT_FOV1: FIFO 1 overrun interrupt

  *            @arg CAN_IT_WKU : Wake-up interrupt

  *            @arg CAN_IT_SLK : Sleep acknowledge interrupt

  *            @arg CAN_IT_EWG : Error warning interrupt

  *            @arg CAN_IT_EPV : Error passive interrupt

  *            @arg CAN_IT_BOF : Bus-off interrupt

  *            @arg CAN_IT_LEC : Last error code interrupt

  *            @arg CAN_IT_ERR : Error Interrupt

  * @retval The new state of __IT__ (TRUE or FALSE).

  */

#define __HAL_CAN_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((__HANDLE__)->Instance->IER & (__INTERRUPT__)) == (__INTERRUPT__)) ? SET : RESET)

/**

  * @brief  Check the transmission status of a CAN Frame.

  * @param  __HANDLE__: specifies the CAN Handle.

  * @param  __TRANSMITMAILBOX__: the number of the mailbox that is used for transmission.

  * @retval The new status of transmission  (TRUE or FALSE).

  */

#define __HAL_CAN_TRANSMIT_STATUS(__HANDLE__, __TRANSMITMAILBOX__)\

(((__TRANSMITMAILBOX__) == CAN_TXMAILBOX_0)? ((((__HANDLE__)->Instance->TSR) & (CAN_TSR_RQCP0 | CAN_TSR_TME0)) == (CAN_TSR_RQCP0 | CAN_TSR_TME0)) :\

 ((__TRANSMITMAILBOX__) == CAN_TXMAILBOX_1)? ((((__HANDLE__)->Instance->TSR) & (CAN_TSR_RQCP1 | CAN_TSR_TME1)) == (CAN_TSR_RQCP1 | CAN_TSR_TME1)) :\

 ((((__HANDLE__)->Instance->TSR) & (CAN_TSR_RQCP2 | CAN_TSR_TME2)) == (CAN_TSR_RQCP2 | CAN_TSR_TME2)))

/**

  * @brief  Release the specified receive FIFO.

  * @param  __HANDLE__: CAN handle.

  * @param  __FIFONUMBER__: Receive FIFO number, CAN_FIFO0 or CAN_FIFO1.

  * @retval None.

  */

#define __HAL_CAN_FIFO_RELEASE(__HANDLE__, __FIFONUMBER__) (((__FIFONUMBER__) == CAN_FIFO0)? \

((__HANDLE__)->Instance->RF0R = CAN_RF0R_RFOM0) : ((__HANDLE__)->Instance->RF1R = CAN_RF1R_RFOM1)) 

/**

  * @brief  Cancel a transmit request.

  * @param  __HANDLE__: specifies the CAN Handle.

  * @param  __TRANSMITMAILBOX__: the number of the mailbox that is used for transmission.

  * @retval None.

  */

#define __HAL_CAN_CANCEL_TRANSMIT(__HANDLE__, __TRANSMITMAILBOX__)\

(((__TRANSMITMAILBOX__) == CAN_TXMAILBOX_0)? ((__HANDLE__)->Instance->TSR = CAN_TSR_ABRQ0) :\

 ((__TRANSMITMAILBOX__) == CAN_TXMAILBOX_1)? ((__HANDLE__)->Instance->TSR = CAN_TSR_ABRQ1) :\

 ((__HANDLE__)->Instance->TSR = CAN_TSR_ABRQ2))

/**

  * @brief  Enable or disables the DBG Freeze for CAN.

  * @param  __HANDLE__: specifies the CAN Handle.

  * @param  __NEWSTATE__: new state of the CAN peripheral.

  *         This parameter can be: ENABLE (CAN reception/transmission is frozen

  *         during debug. Reception FIFOs can still be accessed/controlled normally)

  *         or DISABLE (CAN is working during debug).

  * @retval None

  */

#define __HAL_CAN_DBG_FREEZE(__HANDLE__, __NEWSTATE__) (((__NEWSTATE__) == ENABLE)? \

((__HANDLE__)->Instance->MCR |= CAN_MCR_DBF) : ((__HANDLE__)->Instance->MCR &= ~CAN_MCR_DBF))

/**

  * @}

  */

/* Include CAN HAL Extension module */

#include "stm32f1xx_hal_can_ex_legacy.h"

/* Exported functions --------------------------------------------------------*/

/** @addtogroup CAN_Exported_Functions

  * @{

  */

/** @addtogroup CAN_Exported_Functions_Group1

  * @brief    Initialization and Configuration functions

  * @{

  */

/* Initialization and de-initialization functions *****************************/

HAL_StatusTypeDef HAL_CAN_Init(CAN_HandleTypeDef* hcan);

HAL_StatusTypeDef HAL_CAN_ConfigFilter(CAN_HandleTypeDef* hcan, CAN_FilterConfTypeDef* sFilterConfig);

HAL_StatusTypeDef HAL_CAN_DeInit(CAN_HandleTypeDef* hcan);

void HAL_CAN_MspInit(CAN_HandleTypeDef* hcan);

void HAL_CAN_MspDeInit(CAN_HandleTypeDef* hcan);

/**

  * @}

  */

/** @addtogroup CAN_Exported_Functions_Group2

  * @brief    I/O operation functions

  * @{

  */

/* I/O operation functions *****************************************************/

HAL_StatusTypeDef HAL_CAN_Transmit(CAN_HandleTypeDef *hcan, uint32_t Timeout);

HAL_StatusTypeDef HAL_CAN_Transmit_IT(CAN_HandleTypeDef *hcan);

HAL_StatusTypeDef HAL_CAN_Receive(CAN_HandleTypeDef *hcan, uint8_t FIFONumber, uint32_t Timeout);

HAL_StatusTypeDef HAL_CAN_Receive_IT(CAN_HandleTypeDef *hcan, uint8_t FIFONumber);

HAL_StatusTypeDef HAL_CAN_Sleep(CAN_HandleTypeDef *hcan);

HAL_StatusTypeDef HAL_CAN_WakeUp(CAN_HandleTypeDef *hcan);

void HAL_CAN_IRQHandler(CAN_HandleTypeDef* hcan);

void HAL_CAN_TxCpltCallback(CAN_HandleTypeDef* hcan);

void HAL_CAN_RxCpltCallback(CAN_HandleTypeDef* hcan);

void HAL_CAN_ErrorCallback(CAN_HandleTypeDef *hcan);

/**

  * @}

  */

/** @addtogroup CAN_Exported_Functions_Group3

  * @brief   CAN Peripheral State functions

  * @{

  */

/* Peripheral State and Error functions ***************************************/

uint32_t HAL_CAN_GetError(CAN_HandleTypeDef *hcan);

HAL_CAN_StateTypeDef HAL_CAN_GetState(CAN_HandleTypeDef* hcan);

/**

  * @}

  */

/**

  * @}

  */

/* Private macros --------------------------------------------------------*/

/** @defgroup CAN_Private_Macros   CAN Private Macros

  * @{

  */

#define IS_CAN_MODE(MODE) (((MODE) == CAN_MODE_NORMAL) || \

                           ((MODE) == CAN_MODE_LOOPBACK)|| \

                           ((MODE) == CAN_MODE_SILENT) || \

                           ((MODE) == CAN_MODE_SILENT_LOOPBACK))

#define IS_CAN_SJW(SJW) (((SJW) == CAN_SJW_1TQ) || ((SJW) == CAN_SJW_2TQ)|| \

                         ((SJW) == CAN_SJW_3TQ) || ((SJW) == CAN_SJW_4TQ))

#define IS_CAN_BS1(BS1) ((BS1) <= CAN_BS1_16TQ)

#define IS_CAN_BS2(BS2) ((BS2) <= CAN_BS2_8TQ)

#define IS_CAN_PRESCALER(PRESCALER) (((PRESCALER) >= 1U) && ((PRESCALER) <= 1024U))

#define IS_CAN_FILTER_MODE(MODE) (((MODE) == CAN_FILTERMODE_IDMASK) || \

                                  ((MODE) == CAN_FILTERMODE_IDLIST))

#define IS_CAN_FILTER_SCALE(SCALE) (((SCALE) == CAN_FILTERSCALE_16BIT) || \

                                    ((SCALE) == CAN_FILTERSCALE_32BIT))

#define IS_CAN_FILTER_FIFO(FIFO) (((FIFO) == CAN_FILTER_FIFO0) || \

                                  ((FIFO) == CAN_FILTER_FIFO1))

#define IS_CAN_BANKNUMBER(BANKNUMBER) ((BANKNUMBER) <= 28U)

#define IS_CAN_TRANSMITMAILBOX(TRANSMITMAILBOX) ((TRANSMITMAILBOX) <= ((uint8_t)0x02))

#define IS_CAN_STDID(STDID)   ((STDID) <= 0x00007FFU)

#define IS_CAN_EXTID(EXTID)   ((EXTID) <= 0x1FFFFFFFU)

#define IS_CAN_DLC(DLC)       ((DLC) <= ((uint8_t)0x08))

#define IS_CAN_IDTYPE(IDTYPE)  (((IDTYPE) == CAN_ID_STD) || \

                                ((IDTYPE) == CAN_ID_EXT))

#define IS_CAN_RTR(RTR) (((RTR) == CAN_RTR_DATA) || ((RTR) == CAN_RTR_REMOTE))

#define IS_CAN_FIFO(FIFO) (((FIFO) == CAN_FIFO0) || ((FIFO) == CAN_FIFO1))

/**

  * @}

  */

/**

  * @}

  */

/**

  * @}

  */

#endif /* STM32F103x6) || STM32F103xB || STM32F103xE || STM32F103xG) || STM32F105xC || STM32F107xC */

#ifdef __cplusplus

}

#endif

#endif /* __STM32F1xx_HAL_CAN_LEGACY_H */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/