Subversion Repositories FuelGauge

/**

  ******************************************************************************

  * @file    stm32f0xx_ll_usart.c

  * @author  MCD Application Team

  * @brief   USART LL module driver.

  ******************************************************************************

  * @attention

  *

  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.

  * All rights reserved.</center></h2>

  *

  * This software component is licensed by ST under BSD 3-Clause license,

  * the "License"; You may not use this file except in compliance with the

  * License. You may obtain a copy of the License at:

  *                        opensource.org/licenses/BSD-3-Clause

  *

  ******************************************************************************

  */

#if defined(USE_FULL_LL_DRIVER)

/* Includes ------------------------------------------------------------------*/

#include "stm32f0xx_ll_usart.h"

#include "stm32f0xx_ll_rcc.h"

#include "stm32f0xx_ll_bus.h"

#ifdef USE_FULL_ASSERT

#include "stm32_assert.h"

#else

#define assert_param(expr) ((void)0U)

#endif /* USE_FULL_ASSERT */

/** @addtogroup STM32F0xx_LL_Driver

  * @{

  */

#if defined (USART1) || defined (USART2) || defined (USART3) || defined (UART4) || defined (UART5) || defined (USART6) || defined (USART7) || defined (USART8)

/** @addtogroup USART_LL

  * @{

  */

/* Private types -------------------------------------------------------------*/

/* Private variables ---------------------------------------------------------*/

/* Private constants ---------------------------------------------------------*/

/* Private macros ------------------------------------------------------------*/

/** @addtogroup USART_LL_Private_Macros

  * @{

  */

/* __BAUDRATE__ The maximum Baud Rate is derived from the maximum clock available

 *              divided by the smallest oversampling used on the USART (i.e. 8)    */

#define IS_LL_USART_BAUDRATE(__BAUDRATE__) ((__BAUDRATE__) <= 6000000U)

/* __VALUE__ In case of oversampling by 16 and 8, BRR content must be greater than or equal to 16d. */

#define IS_LL_USART_BRR_MIN(__VALUE__) ((__VALUE__) >= 16U)

#define IS_LL_USART_DIRECTION(__VALUE__) (((__VALUE__) == LL_USART_DIRECTION_NONE) \

                                          || ((__VALUE__) == LL_USART_DIRECTION_RX) \

                                          || ((__VALUE__) == LL_USART_DIRECTION_TX) \

                                          || ((__VALUE__) == LL_USART_DIRECTION_TX_RX))

#define IS_LL_USART_PARITY(__VALUE__) (((__VALUE__) == LL_USART_PARITY_NONE) \

                                       || ((__VALUE__) == LL_USART_PARITY_EVEN) \

                                       || ((__VALUE__) == LL_USART_PARITY_ODD))

#if defined(USART_7BITS_SUPPORT)

#define IS_LL_USART_DATAWIDTH(__VALUE__) (((__VALUE__) == LL_USART_DATAWIDTH_7B) \

                                          || ((__VALUE__) == LL_USART_DATAWIDTH_8B) \

                                          || ((__VALUE__) == LL_USART_DATAWIDTH_9B))

#else

#define IS_LL_USART_DATAWIDTH(__VALUE__) (((__VALUE__) == LL_USART_DATAWIDTH_8B) \

                                          || ((__VALUE__) == LL_USART_DATAWIDTH_9B))

#endif /* USART_7BITS_SUPPORT */

#define IS_LL_USART_OVERSAMPLING(__VALUE__) (((__VALUE__) == LL_USART_OVERSAMPLING_16) \

                                             || ((__VALUE__) == LL_USART_OVERSAMPLING_8))

#define IS_LL_USART_LASTBITCLKOUTPUT(__VALUE__) (((__VALUE__) == LL_USART_LASTCLKPULSE_NO_OUTPUT) \

                                                 || ((__VALUE__) == LL_USART_LASTCLKPULSE_OUTPUT))

#define IS_LL_USART_CLOCKPHASE(__VALUE__) (((__VALUE__) == LL_USART_PHASE_1EDGE) \

                                           || ((__VALUE__) == LL_USART_PHASE_2EDGE))

#define IS_LL_USART_CLOCKPOLARITY(__VALUE__) (((__VALUE__) == LL_USART_POLARITY_LOW) \

                                              || ((__VALUE__) == LL_USART_POLARITY_HIGH))

#define IS_LL_USART_CLOCKOUTPUT(__VALUE__) (((__VALUE__) == LL_USART_CLOCK_DISABLE) \

                                            || ((__VALUE__) == LL_USART_CLOCK_ENABLE))

#if defined(USART_SMARTCARD_SUPPORT)

#define IS_LL_USART_STOPBITS(__VALUE__) (((__VALUE__) == LL_USART_STOPBITS_0_5) \

                                         || ((__VALUE__) == LL_USART_STOPBITS_1) \

                                         || ((__VALUE__) == LL_USART_STOPBITS_1_5) \

                                         || ((__VALUE__) == LL_USART_STOPBITS_2))

#else

#define IS_LL_USART_STOPBITS(__VALUE__) (((__VALUE__) == LL_USART_STOPBITS_1) \

                                         || ((__VALUE__) == LL_USART_STOPBITS_2))

#endif

#define IS_LL_USART_HWCONTROL(__VALUE__) (((__VALUE__) == LL_USART_HWCONTROL_NONE) \

                                          || ((__VALUE__) == LL_USART_HWCONTROL_RTS) \

                                          || ((__VALUE__) == LL_USART_HWCONTROL_CTS) \

                                          || ((__VALUE__) == LL_USART_HWCONTROL_RTS_CTS))

/**

  * @}

  */

/* Private function prototypes -----------------------------------------------*/

/* Exported functions --------------------------------------------------------*/

/** @addtogroup USART_LL_Exported_Functions

  * @{

  */

/** @addtogroup USART_LL_EF_Init

  * @{

  */

/**

  * @brief  De-initialize USART registers (Registers restored to their default values).

  * @param  USARTx USART Instance

  * @retval An ErrorStatus enumeration value:

  *          - SUCCESS: USART registers are de-initialized

  *          - ERROR: USART registers are not de-initialized

  */

ErrorStatus LL_USART_DeInit(USART_TypeDef *USARTx)

{

  ErrorStatus status = SUCCESS;

  /* Check the parameters */

  assert_param(IS_UART_INSTANCE(USARTx));

  if (USARTx == USART1)

  {

    /* Force reset of USART clock */

    LL_APB1_GRP2_ForceReset(LL_APB1_GRP2_PERIPH_USART1);

    /* Release reset of USART clock */

    LL_APB1_GRP2_ReleaseReset(LL_APB1_GRP2_PERIPH_USART1);

  }

#if defined(USART2)

  else if (USARTx == USART2)

  {

    /* Force reset of USART clock */

    LL_APB1_GRP1_ForceReset(LL_APB1_GRP1_PERIPH_USART2);

    /* Release reset of USART clock */

    LL_APB1_GRP1_ReleaseReset(LL_APB1_GRP1_PERIPH_USART2);

  }

#endif /* USART2 */

#if defined(USART3)

  else if (USARTx == USART3)

  {

    /* Force reset of USART clock */

    LL_APB1_GRP1_ForceReset(LL_APB1_GRP1_PERIPH_USART3);

    /* Release reset of USART clock */

    LL_APB1_GRP1_ReleaseReset(LL_APB1_GRP1_PERIPH_USART3);

  }

#endif /* USART3 */

#if defined(USART4)

  else if (USARTx == USART4)

  {

    /* Force reset of USART clock */

    LL_APB1_GRP1_ForceReset(LL_APB1_GRP1_PERIPH_USART4);

    /* Release reset of USART clock */

    LL_APB1_GRP1_ReleaseReset(LL_APB1_GRP1_PERIPH_USART4);

  }

#endif /* USART4 */

#if defined(USART5)

  else if (USARTx == USART5)

  {

    /* Force reset of USART clock */

    LL_APB1_GRP1_ForceReset(LL_APB1_GRP1_PERIPH_USART5);

    /* Release reset of USART clock */

    LL_APB1_GRP1_ReleaseReset(LL_APB1_GRP1_PERIPH_USART5);

  }

#endif /* USART5 */

#if defined(USART6)

  else if (USARTx == USART6)

  {

    /* Force reset of USART clock */

    LL_APB1_GRP2_ForceReset(LL_APB1_GRP2_PERIPH_USART6);

    /* Release reset of USART clock */

    LL_APB1_GRP2_ReleaseReset(LL_APB1_GRP2_PERIPH_USART6);

  }

#endif /* USART6 */

#if defined(USART7)

  else if (USARTx == USART7)

  {

    /* Force reset of USART clock */

    LL_APB1_GRP2_ForceReset(LL_APB1_GRP2_PERIPH_USART7);

    /* Release reset of USART clock */

    LL_APB1_GRP2_ReleaseReset(LL_APB1_GRP2_PERIPH_USART7);

  }

#endif /* USART7 */

#if defined(USART8)

  else if (USARTx == USART8)

  {

    /* Force reset of USART clock */

    LL_APB1_GRP2_ForceReset(LL_APB1_GRP2_PERIPH_USART8);

    /* Release reset of USART clock */

    LL_APB1_GRP2_ReleaseReset(LL_APB1_GRP2_PERIPH_USART8);

  }

#endif /* USART8 */

  else

  {

    status = ERROR;

  }

  return (status);

}

/**

  * @brief  Initialize USART registers according to the specified

  *         parameters in USART_InitStruct.

  * @note   As some bits in USART configuration registers can only be written when

  *         the USART is disabled (USART_CR1_UE bit =0), USART Peripheral should be in disabled state prior calling

  *         this function. Otherwise, ERROR result will be returned.

  * @note   Baud rate value stored in USART_InitStruct BaudRate field, should be valid (different from 0).

  * @param  USARTx USART Instance

  * @param  USART_InitStruct pointer to a LL_USART_InitTypeDef structure

  *         that contains the configuration information for the specified USART peripheral.

  * @retval An ErrorStatus enumeration value:

  *          - SUCCESS: USART registers are initialized according to USART_InitStruct content

  *          - ERROR: Problem occurred during USART Registers initialization

  */

ErrorStatus LL_USART_Init(USART_TypeDef *USARTx, LL_USART_InitTypeDef *USART_InitStruct)

{

  ErrorStatus status = ERROR;

  uint32_t periphclk = LL_RCC_PERIPH_FREQUENCY_NO;

#if defined(USART2)||defined(USART3)||defined(USART4)

  LL_RCC_ClocksTypeDef RCC_Clocks;

#endif /* USART2 ||USART3 || USART4 */

  /* Check the parameters */

  assert_param(IS_UART_INSTANCE(USARTx));

  assert_param(IS_LL_USART_BAUDRATE(USART_InitStruct->BaudRate));

  assert_param(IS_LL_USART_DATAWIDTH(USART_InitStruct->DataWidth));

  assert_param(IS_LL_USART_STOPBITS(USART_InitStruct->StopBits));

  assert_param(IS_LL_USART_PARITY(USART_InitStruct->Parity));

  assert_param(IS_LL_USART_DIRECTION(USART_InitStruct->TransferDirection));

  assert_param(IS_LL_USART_HWCONTROL(USART_InitStruct->HardwareFlowControl));

  assert_param(IS_LL_USART_OVERSAMPLING(USART_InitStruct->OverSampling));

  /* USART needs to be in disabled state, in order to be able to configure some bits in

     CRx registers */

  if (LL_USART_IsEnabled(USARTx) == 0U)

  {

    /*---------------------------- USART CR1 Configuration ---------------------

     * Configure USARTx CR1 (USART Word Length, Parity, Mode and Oversampling bits) with parameters:

     * - DataWidth:          USART_CR1_M bits according to USART_InitStruct->DataWidth value

     * - Parity:             USART_CR1_PCE, USART_CR1_PS bits according to USART_InitStruct->Parity value

     * - TransferDirection:  USART_CR1_TE, USART_CR1_RE bits according to USART_InitStruct->TransferDirection value

     * - Oversampling:       USART_CR1_OVER8 bit according to USART_InitStruct->OverSampling value.

     */

    MODIFY_REG(USARTx->CR1,

               (USART_CR1_M | USART_CR1_PCE | USART_CR1_PS |

                USART_CR1_TE | USART_CR1_RE | USART_CR1_OVER8),

               (USART_InitStruct->DataWidth | USART_InitStruct->Parity |

                USART_InitStruct->TransferDirection | USART_InitStruct->OverSampling));

    /*---------------------------- USART CR2 Configuration ---------------------

     * Configure USARTx CR2 (Stop bits) with parameters:

     * - Stop Bits:          USART_CR2_STOP bits according to USART_InitStruct->StopBits value.

     * - CLKEN, CPOL, CPHA and LBCL bits are to be configured using LL_USART_ClockInit().

     */

    LL_USART_SetStopBitsLength(USARTx, USART_InitStruct->StopBits);

    /*---------------------------- USART CR3 Configuration ---------------------

     * Configure USARTx CR3 (Hardware Flow Control) with parameters:

     * - HardwareFlowControl: USART_CR3_RTSE, USART_CR3_CTSE bits according to

     *   USART_InitStruct->HardwareFlowControl value.

     */

    LL_USART_SetHWFlowCtrl(USARTx, USART_InitStruct->HardwareFlowControl);

    /*---------------------------- USART BRR Configuration ---------------------

     * Retrieve Clock frequency used for USART Peripheral

     */

    if (USARTx == USART1)

    {

      periphclk = LL_RCC_GetUSARTClockFreq(LL_RCC_USART1_CLKSOURCE);

    }

#if defined(USART2)

    else if (USARTx == USART2)

    {

#if defined(RCC_CFGR3_USART2SW)

      periphclk = LL_RCC_GetUSARTClockFreq(LL_RCC_USART2_CLKSOURCE);

#else

      /* USART2 clock is PCLK */

      LL_RCC_GetSystemClocksFreq(&RCC_Clocks);

      periphclk = RCC_Clocks.PCLK1_Frequency;

#endif

    }

#endif /* USART2 */

#if defined(USART3)

    else if (USARTx == USART3)

    {

#if defined(RCC_CFGR3_USART3SW)

      periphclk = LL_RCC_GetUSARTClockFreq(LL_RCC_USART3_CLKSOURCE);

#else

      /* USART3 clock is PCLK */

      LL_RCC_GetSystemClocksFreq(&RCC_Clocks);

      periphclk = RCC_Clocks.PCLK1_Frequency;

#endif

    }

#endif /* USART3 */

#if defined(USART4)

    else if (USARTx == USART4)

    {

      /* USART4 clock is PCLK1 */

      LL_RCC_GetSystemClocksFreq(&RCC_Clocks);

      periphclk = RCC_Clocks.PCLK1_Frequency;

    }

#endif /* USART4 */

#if defined(USART5)

    else if (USARTx == USART5)

    {

      /* USART5 clock is PCLK1 */

      LL_RCC_GetSystemClocksFreq(&RCC_Clocks);

      periphclk = RCC_Clocks.PCLK1_Frequency;

    }

#endif /* USART5 */

#if defined(USART6)

    else if (USARTx == USART6)

    {

      /* USART6 clock is PCLK1 */

      LL_RCC_GetSystemClocksFreq(&RCC_Clocks);

      periphclk = RCC_Clocks.PCLK1_Frequency;

    }

#endif /* USART6 */

#if defined(USART7)

    else if (USARTx == USART7)

    {

      /* USART7 clock is PCLK */

      LL_RCC_GetSystemClocksFreq(&RCC_Clocks);

      periphclk = RCC_Clocks.PCLK1_Frequency;

    }

#endif /* USART7 */

#if defined(USART8)

    else if (USARTx == USART8)

    {

      /* USART8 clock is PCLK */

      LL_RCC_GetSystemClocksFreq(&RCC_Clocks);

      periphclk = RCC_Clocks.PCLK1_Frequency;

    }

#endif /* USART8 */

    else

    {

      /* Nothing to do, as error code is already assigned to ERROR value */

    }

    /* Configure the USART Baud Rate :

       - valid baud rate value (different from 0) is required

       - Peripheral clock as returned by RCC service, should be valid (different from 0).

    */

    if ((periphclk != LL_RCC_PERIPH_FREQUENCY_NO)

        && (USART_InitStruct->BaudRate != 0U))

    {

      status = SUCCESS;

      LL_USART_SetBaudRate(USARTx,

                           periphclk,

                           USART_InitStruct->OverSampling,

                           USART_InitStruct->BaudRate);

      /* Check BRR is greater than or equal to 16d */

      assert_param(IS_LL_USART_BRR_MIN(USARTx->BRR));

    }

  }

  /* Endif (=> USART not in Disabled state => return ERROR) */

  return (status);

}

/**

  * @brief Set each @ref LL_USART_InitTypeDef field to default value.

  * @param USART_InitStruct pointer to a @ref LL_USART_InitTypeDef structure

  *                         whose fields will be set to default values.

  * @retval None

  */

void LL_USART_StructInit(LL_USART_InitTypeDef *USART_InitStruct)

{

  /* Set USART_InitStruct fields to default values */

  USART_InitStruct->BaudRate            = 9600U;

  USART_InitStruct->DataWidth           = LL_USART_DATAWIDTH_8B;

  USART_InitStruct->StopBits            = LL_USART_STOPBITS_1;

  USART_InitStruct->Parity              = LL_USART_PARITY_NONE ;

  USART_InitStruct->TransferDirection   = LL_USART_DIRECTION_TX_RX;

  USART_InitStruct->HardwareFlowControl = LL_USART_HWCONTROL_NONE;

  USART_InitStruct->OverSampling        = LL_USART_OVERSAMPLING_16;

}

/**

  * @brief  Initialize USART Clock related settings according to the

  *         specified parameters in the USART_ClockInitStruct.

  * @note   As some bits in USART configuration registers can only be written when

  *         the USART is disabled (USART_CR1_UE bit =0), USART Peripheral should be in disabled state prior calling

  *         this function. Otherwise, ERROR result will be returned.

  * @param  USARTx USART Instance

  * @param  USART_ClockInitStruct pointer to a @ref LL_USART_ClockInitTypeDef structure

  *         that contains the Clock configuration information for the specified USART peripheral.

  * @retval An ErrorStatus enumeration value:

  *          - SUCCESS: USART registers related to Clock settings are initialized according

  *                     to USART_ClockInitStruct content

  *          - ERROR: Problem occurred during USART Registers initialization

  */

ErrorStatus LL_USART_ClockInit(USART_TypeDef *USARTx, LL_USART_ClockInitTypeDef *USART_ClockInitStruct)

{

  ErrorStatus status = SUCCESS;

  /* Check USART Instance and Clock signal output parameters */

  assert_param(IS_UART_INSTANCE(USARTx));

  assert_param(IS_LL_USART_CLOCKOUTPUT(USART_ClockInitStruct->ClockOutput));

  /* USART needs to be in disabled state, in order to be able to configure some bits in

     CRx registers */

  if (LL_USART_IsEnabled(USARTx) == 0U)

  {

    /* If USART Clock signal is disabled */

    if (USART_ClockInitStruct->ClockOutput == LL_USART_CLOCK_DISABLE)

    {

      /* Deactivate Clock signal delivery :

       * - Disable Clock Output:        USART_CR2_CLKEN cleared

       */

      LL_USART_DisableSCLKOutput(USARTx);

    }

    else

    {

      /* Ensure USART instance is USART capable */

      assert_param(IS_USART_INSTANCE(USARTx));

      /* Check clock related parameters */

      assert_param(IS_LL_USART_CLOCKPOLARITY(USART_ClockInitStruct->ClockPolarity));

      assert_param(IS_LL_USART_CLOCKPHASE(USART_ClockInitStruct->ClockPhase));

      assert_param(IS_LL_USART_LASTBITCLKOUTPUT(USART_ClockInitStruct->LastBitClockPulse));

      /*---------------------------- USART CR2 Configuration -----------------------

       * Configure USARTx CR2 (Clock signal related bits) with parameters:

       * - Enable Clock Output:         USART_CR2_CLKEN set

       * - Clock Polarity:              USART_CR2_CPOL bit according to USART_ClockInitStruct->ClockPolarity value

       * - Clock Phase:                 USART_CR2_CPHA bit according to USART_ClockInitStruct->ClockPhase value

       * - Last Bit Clock Pulse Output: USART_CR2_LBCL bit according to USART_ClockInitStruct->LastBitClockPulse value.

       */

      MODIFY_REG(USARTx->CR2,

                 USART_CR2_CLKEN | USART_CR2_CPHA | USART_CR2_CPOL | USART_CR2_LBCL,

                 USART_CR2_CLKEN | USART_ClockInitStruct->ClockPolarity |

                 USART_ClockInitStruct->ClockPhase | USART_ClockInitStruct->LastBitClockPulse);

    }

  }

  /* Else (USART not in Disabled state => return ERROR */

  else

  {

    status = ERROR;

  }

  return (status);

}

/**

  * @brief Set each field of a @ref LL_USART_ClockInitTypeDef type structure to default value.

  * @param USART_ClockInitStruct pointer to a @ref LL_USART_ClockInitTypeDef structure

  *                              whose fields will be set to default values.

  * @retval None

  */

void LL_USART_ClockStructInit(LL_USART_ClockInitTypeDef *USART_ClockInitStruct)

{

  /* Set LL_USART_ClockInitStruct fields with default values */

  USART_ClockInitStruct->ClockOutput       = LL_USART_CLOCK_DISABLE;

  USART_ClockInitStruct->ClockPolarity     = LL_USART_POLARITY_LOW;            /* Not relevant when ClockOutput =

                                                                                  LL_USART_CLOCK_DISABLE */

  USART_ClockInitStruct->ClockPhase        = LL_USART_PHASE_1EDGE;             /* Not relevant when ClockOutput =

                                                                                  LL_USART_CLOCK_DISABLE */

  USART_ClockInitStruct->LastBitClockPulse = LL_USART_LASTCLKPULSE_NO_OUTPUT;  /* Not relevant when ClockOutput =

                                                                                  LL_USART_CLOCK_DISABLE */

}

/**

  * @}

  */

/**

  * @}

  */

/**

  * @}

  */

#endif /* USART1 || USART2 || USART3 || UART4 || UART5 || USART6 || USART7 || USART8 */

/**

  * @}

  */

#endif /* USE_FULL_LL_DRIVER */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/