Subversion Repositories FuelGauge

/**

  ******************************************************************************

  * @file    stm32f0xx_hal_rtc.c

  * @author  MCD Application Team

  * @brief   RTC HAL module driver.

  *          This file provides firmware functions to manage the following

  *          functionalities of the Real Time Clock (RTC) peripheral:

  *           + Initialization and de-initialization functions

  *           + RTC Time and Date functions

  *           + RTC Alarm functions

  *           + Peripheral Control functions

  *           + Peripheral State functions

  *

  @verbatim

  ==============================================================================

                  ##### How to use RTC Driver #####

 ===================================================================

    [..]

        (+) Enable the RTC domain access (see description in the section above).

        (+) Configure the RTC Prescaler (Asynchronous and Synchronous) and RTC hour

            format using the HAL_RTC_Init() function.

    *** Time and Date configuration ***

    ===================================

    [..]

        (+) To configure the RTC Calendar (Time and Date) use the HAL_RTC_SetTime()

            and HAL_RTC_SetDate() functions.

        (+) To read the RTC Calendar, use the HAL_RTC_GetTime() and HAL_RTC_GetDate() functions.

    *** Alarm configuration ***

    ===========================

    [..]

    (+) To configure the RTC Alarm use the HAL_RTC_SetAlarm() function.

            You can also configure the RTC Alarm with interrupt mode using the

            HAL_RTC_SetAlarm_IT() function.

        (+) To read the RTC Alarm, use the HAL_RTC_GetAlarm() function.

                  ##### RTC and low power modes #####

 ===================================================================

    [..] The MCU can be woken up from a low power mode by an RTC alternate

         function.

    [..] The RTC alternate functions are the RTC alarm (Alarm A),

         RTC wake-up, RTC tamper event detection and RTC time stamp event detection.

         These RTC alternate functions can wake up the system from the Stop and

         Standby low power modes.

    [..] The system can also wake up from low power modes without depending

         on an external interrupt (Auto-wake-up mode), by using the RTC alarm

         or the RTC wake-up events.

    [..] The RTC provides a programmable time base for waking up from the

         Stop or Standby mode at regular intervals.

         Wake-up from STOP and STANDBY modes is possible only when the RTC clock source

         is LSE or LSI.

  *** Callback registration ***

  =============================================

  The compilation define  USE_RTC_REGISTER_CALLBACKS when set to 1

  allows the user to configure dynamically the driver callbacks.

  Use Function HAL_RTC_RegisterCallback() to register an interrupt callback.

  Function HAL_RTC_RegisterCallback() allows to register following callbacks:

    (+) AlarmAEventCallback          : RTC Alarm A Event callback.

    (+) TimeStampEventCallback       : RTC TimeStamp Event callback.

    (+) WakeUpTimerEventCallback     : RTC WakeUpTimer Event callback.

    (+) Tamper1EventCallback         : RTC Tamper 1 Event callback.

    (+) Tamper2EventCallback         : RTC Tamper 2 Event callback.

    (+) Tamper3EventCallback         : RTC Tamper 3 Event callback.

    (+) MspInitCallback              : RTC MspInit callback.

    (+) MspDeInitCallback            : RTC MspDeInit callback.

  This function takes as parameters the HAL peripheral handle, the Callback ID

  and a pointer to the user callback function.

  Use function HAL_RTC_UnRegisterCallback() to reset a callback to the default

  weak function.

  HAL_RTC_UnRegisterCallback() takes as parameters the HAL peripheral handle,

  and the Callback ID.

  This function allows to reset following callbacks:

    (+) AlarmAEventCallback          : RTC Alarm A Event callback.

    (+) TimeStampEventCallback       : RTC TimeStamp Event callback.

    (+) WakeUpTimerEventCallback     : RTC WakeUpTimer Event callback.

    (+) Tamper1EventCallback         : RTC Tamper 1 Event callback.

    (+) Tamper2EventCallback         : RTC Tamper 2 Event callback.

    (+) Tamper3EventCallback         : RTC Tamper 3 Event callback.

    (+) MspInitCallback              : RTC MspInit callback.

    (+) MspDeInitCallback            : RTC MspDeInit callback.

  By default, after the HAL_RTC_Init() and when the state is HAL_RTC_STATE_RESET,

  all callbacks are set to the corresponding weak functions :

  examples AlarmAEventCallback(), WakeUpTimerEventCallback().

  Exception done for MspInit and MspDeInit callbacks that are reset to the legacy weak function

  in the HAL_RTC_Init()/HAL_RTC_DeInit() only when these callbacks are null

  (not registered beforehand).

  If not, MspInit or MspDeInit are not null, HAL_RTC_Init()/HAL_RTC_DeInit()

  keep and use the user MspInit/MspDeInit callbacks (registered beforehand)

  Callbacks can be registered/unregistered in HAL_RTC_STATE_READY state only.

  Exception done MspInit/MspDeInit that can be registered/unregistered

  in HAL_RTC_STATE_READY or HAL_RTC_STATE_RESET state,

  thus registered (user) MspInit/DeInit callbacks can be used during the Init/DeInit.

  In that case first register the MspInit/MspDeInit user callbacks

  using HAL_RTC_RegisterCallback() before calling HAL_RTC_DeInit()

  or HAL_RTC_Init() function.

  When The compilation define USE_HAL_RTC_REGISTER_CALLBACKS is set to 0 or

  not defined, the callback registration feature is not available and all callbacks

  are set to the corresponding weak functions.

  @endverbatim

  ******************************************************************************

  * @attention

  *

  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.

  * All rights reserved.</center></h2>

  *

  * This software component is licensed by ST under BSD 3-Clause license,

  * the "License"; You may not use this file except in compliance with the

  * License. You may obtain a copy of the License at:

  *                        opensource.org/licenses/BSD-3-Clause

  *

  ******************************************************************************

  */

/* Includes ------------------------------------------------------------------*/

#include "stm32f0xx_hal.h"

/** @addtogroup STM32F0xx_HAL_Driver

  * @{

  */

/** @addtogroup RTC

  * @brief RTC HAL module driver

  * @{

  */

#ifdef HAL_RTC_MODULE_ENABLED

/* Private typedef -----------------------------------------------------------*/

/* Private define ------------------------------------------------------------*/

/* Private macro -------------------------------------------------------------*/

/* Private variables ---------------------------------------------------------*/

/* Private function prototypes -----------------------------------------------*/

/* Exported functions ---------------------------------------------------------*/

/** @addtogroup RTC_Exported_Functions

  * @{

  */

/** @addtogroup RTC_Exported_Functions_Group1

 *  @brief    Initialization and Configuration functions

 *

@verbatim

 ===============================================================================

              ##### Initialization and de-initialization functions #####

 ===============================================================================

   [..] This section provides functions allowing to initialize and configure the

         RTC Prescaler (Synchronous and Asynchronous), RTC Hour format, disable

         RTC registers Write protection, enter and exit the RTC initialization mode,

         RTC registers synchronization check and reference clock detection enable.

         (#) The RTC Prescaler is programmed to generate the RTC 1Hz time base.

             It is split into 2 programmable prescalers to minimize power consumption.

             (++) A 7-bit asynchronous prescaler and a 15-bit synchronous prescaler.

             (++) When both prescalers are used, it is recommended to configure the

                 asynchronous prescaler to a high value to minimize power consumption.

         (#) All RTC registers are Write protected. Writing to the RTC registers

             is enabled by writing a key into the Write Protection register, RTC_WPR.

         (#) To configure the RTC Calendar, user application should enter

             initialization mode. In this mode, the calendar counter is stopped

             and its value can be updated. When the initialization sequence is

             complete, the calendar restarts counting after 4 RTCCLK cycles.

         (#) To read the calendar through the shadow registers after Calendar

             initialization, calendar update or after wake-up from low power modes

             the software must first clear the RSF flag. The software must then

             wait until it is set again before reading the calendar, which means

             that the calendar registers have been correctly copied into the

             RTC_TR and RTC_DR shadow registers.The HAL_RTC_WaitForSynchro() function

             implements the above software sequence (RSF clear and RSF check).

@endverbatim

  * @{

  */

/**

  * @brief  Initialize the RTC according to the specified parameters

  *         in the RTC_InitTypeDef structure and initialize the associated handle.

  * @param  hrtc RTC handle

  * @retval HAL status

  */

HAL_StatusTypeDef HAL_RTC_Init(RTC_HandleTypeDef *hrtc)

{

  /* Check the RTC peripheral state */

  if (hrtc == NULL)

  {

    return HAL_ERROR;

  }

  /* Check the parameters */

  assert_param(IS_RTC_ALL_INSTANCE(hrtc->Instance));

  assert_param(IS_RTC_HOUR_FORMAT(hrtc->Init.HourFormat));

  assert_param(IS_RTC_ASYNCH_PREDIV(hrtc->Init.AsynchPrediv));

  assert_param(IS_RTC_SYNCH_PREDIV(hrtc->Init.SynchPrediv));

  assert_param(IS_RTC_OUTPUT(hrtc->Init.OutPut));

  assert_param(IS_RTC_OUTPUT_POL(hrtc->Init.OutPutPolarity));

  assert_param(IS_RTC_OUTPUT_TYPE(hrtc->Init.OutPutType));

#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)

  if (hrtc->State == HAL_RTC_STATE_RESET)

  {

    /* Allocate lock resource and initialize it */

    hrtc->Lock = HAL_UNLOCKED;

    hrtc->AlarmAEventCallback          =  HAL_RTC_AlarmAEventCallback;        /* Legacy weak AlarmAEventCallback      */

    hrtc->TimeStampEventCallback       =  HAL_RTCEx_TimeStampEventCallback;   /* Legacy weak TimeStampEventCallback   */

#if defined(RTC_WAKEUP_SUPPORT)

    hrtc->WakeUpTimerEventCallback     =  HAL_RTCEx_WakeUpTimerEventCallback; /* Legacy weak WakeUpTimerEventCallback */

#endif /* RTC_WAKEUP_SUPPORT */

    hrtc->Tamper1EventCallback         =  HAL_RTCEx_Tamper1EventCallback;     /* Legacy weak Tamper1EventCallback     */

    hrtc->Tamper2EventCallback         =  HAL_RTCEx_Tamper2EventCallback;     /* Legacy weak Tamper2EventCallback     */

#if defined(RTC_TAMPER3_SUPPORT)

    hrtc->Tamper3EventCallback         =  HAL_RTCEx_Tamper3EventCallback;     /* Legacy weak Tamper3EventCallback     */

#endif /* RTC_TAMPER3_SUPPORT */

    if (hrtc->MspInitCallback == NULL)

    {

      hrtc->MspInitCallback = HAL_RTC_MspInit;

    }

    /* Init the low level hardware */

    hrtc->MspInitCallback(hrtc);

    if (hrtc->MspDeInitCallback == NULL)

    {

      hrtc->MspDeInitCallback = HAL_RTC_MspDeInit;

    }

  }

#else

  if (hrtc->State == HAL_RTC_STATE_RESET)

  {

    /* Allocate lock resource and initialize it */

    hrtc->Lock = HAL_UNLOCKED;

    /* Initialize RTC MSP */

    HAL_RTC_MspInit(hrtc);

  }

#endif /* (USE_HAL_RTC_REGISTER_CALLBACKS) */

  /* Set RTC state */

  hrtc->State = HAL_RTC_STATE_BUSY;

  /* Disable the write protection for RTC registers */

  __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);

  /* Set Initialization mode */

  if (RTC_EnterInitMode(hrtc) != HAL_OK)

  {

    /* Enable the write protection for RTC registers */

    __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);

    /* Set RTC state */

    hrtc->State = HAL_RTC_STATE_ERROR;

    return HAL_ERROR;

  }

  else

  {

    /* Clear RTC_CR FMT, OSEL and POL Bits */

    hrtc->Instance->CR &= ((uint32_t)~(RTC_CR_FMT | RTC_CR_OSEL | RTC_CR_POL));

    /* Set RTC_CR register */

    hrtc->Instance->CR |= (uint32_t)(hrtc->Init.HourFormat | hrtc->Init.OutPut | hrtc->Init.OutPutPolarity);

    /* Configure the RTC PRER */

    hrtc->Instance->PRER = (uint32_t)(hrtc->Init.SynchPrediv);

    hrtc->Instance->PRER |= (uint32_t)(hrtc->Init.AsynchPrediv << 16U);

    /* Exit Initialization mode */

    hrtc->Instance->ISR &= (uint32_t)~RTC_ISR_INIT;

    /* If  CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */

    if ((hrtc->Instance->CR & RTC_CR_BYPSHAD) == RESET)

    {

      if (HAL_RTC_WaitForSynchro(hrtc) != HAL_OK)

      {

        /* Enable the write protection for RTC registers */

        __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);

        hrtc->State = HAL_RTC_STATE_ERROR;

        return HAL_ERROR;

      }

    }

    hrtc->Instance->TAFCR &= (uint32_t)~RTC_TAFCR_ALARMOUTTYPE;

    hrtc->Instance->TAFCR |= (uint32_t)(hrtc->Init.OutPutType);

    /* Enable the write protection for RTC registers */

    __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);

    /* Set RTC state */

    hrtc->State = HAL_RTC_STATE_READY;

    return HAL_OK;

  }

}

/**

  * @brief  DeInitialize the RTC peripheral.

  * @param  hrtc RTC handle

  * @note   This function doesn't reset the RTC Backup Data registers.

  * @retval HAL status

  */

HAL_StatusTypeDef HAL_RTC_DeInit(RTC_HandleTypeDef *hrtc)

{

#if defined (STM32F030xC) || defined (STM32F070xB) || \

    defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx) || \

    defined (STM32F091xC) || defined (STM32F098xx)

  uint32_t tickstart = 0;

#endif /* defined (STM32F030xC) || defined (STM32F070xB) ||\

          defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx) || \

          defined (STM32F091xC) || defined (STM32F098xx) ||*/

  /* Check the parameters */

  assert_param(IS_RTC_ALL_INSTANCE(hrtc->Instance));

  /* Set RTC state */

  hrtc->State = HAL_RTC_STATE_BUSY;

  /* Disable the write protection for RTC registers */

  __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);

  /* Set Initialization mode */

  if (RTC_EnterInitMode(hrtc) != HAL_OK)

  {

    /* Enable the write protection for RTC registers */

    __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);

    /* Set RTC state */

    hrtc->State = HAL_RTC_STATE_ERROR;

    return HAL_ERROR;

  }

  else

  {

    /* Reset TR, DR and CR registers */

    hrtc->Instance->TR = 0x00000000U;

    hrtc->Instance->DR = 0x00002101U;

#if defined (STM32F030xC) || defined (STM32F070xB) || \

    defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx) || \

    defined (STM32F091xC) || defined (STM32F098xx)

    /* Reset All CR bits except CR[2:0] */

    hrtc->Instance->CR &= 0x00000007U;

    tickstart = HAL_GetTick();

    /* Wait till WUTWF flag is set and if Time out is reached exit */

    while (((hrtc->Instance->ISR) & RTC_ISR_WUTWF) == (uint32_t)RESET)

    {

      if ((HAL_GetTick() - tickstart) >  RTC_TIMEOUT_VALUE)

      {

        /* Enable the write protection for RTC registers */

        __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);

        /* Set RTC state */

        hrtc->State = HAL_RTC_STATE_TIMEOUT;

        return HAL_TIMEOUT;

      }

    }

#endif /* defined (STM32F030xC) || defined (STM32F070xB) ||\

          defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx) || \

          defined (STM32F091xC) || defined (STM32F098xx) ||*/

    /* Reset all RTC CR register bits */

    hrtc->Instance->CR &= 0x00000000U;

#if defined (STM32F030xC) || defined (STM32F070xB) || \

    defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx) || \

    defined (STM32F091xC) || defined (STM32F098xx)

    hrtc->Instance->WUTR = 0x0000FFFFU;

#endif /* defined (STM32F030xC) || defined (STM32F070xB) ||\

          defined (STM32F071xB) || defined (STM32F072xB) || defined (STM32F078xx) || \

          defined (STM32F091xC) || defined (STM32F098xx) ||*/

    hrtc->Instance->PRER = 0x007F00FFU;

    hrtc->Instance->ALRMAR = 0x00000000U;

    hrtc->Instance->SHIFTR = 0x00000000U;

    hrtc->Instance->CALR = 0x00000000U;

    hrtc->Instance->ALRMASSR = 0x00000000U;

    /* Reset ISR register and exit initialization mode */

    hrtc->Instance->ISR = 0x00000000U;

    /* Reset Tamper and alternate functions configuration register */

    hrtc->Instance->TAFCR = 0x00000000;

    /* If  RTC_CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */

    if ((hrtc->Instance->CR & RTC_CR_BYPSHAD) == RESET)

    {

      if (HAL_RTC_WaitForSynchro(hrtc) != HAL_OK)

      {

        /* Enable the write protection for RTC registers */

        __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);

        hrtc->State = HAL_RTC_STATE_ERROR;

        return HAL_ERROR;

      }

    }

  }

  /* Enable the write protection for RTC registers */

  __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);

#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)

  if (hrtc->MspDeInitCallback == NULL)

  {

    hrtc->MspDeInitCallback = HAL_RTC_MspDeInit;

  }

  /* DeInit the low level hardware: CLOCK, NVIC.*/

  hrtc->MspDeInitCallback(hrtc);

#else

  /* De-Initialize RTC MSP */

  HAL_RTC_MspDeInit(hrtc);

#endif /* (USE_HAL_RTC_REGISTER_CALLBACKS) */

  hrtc->State = HAL_RTC_STATE_RESET;

  /* Release Lock */

  __HAL_UNLOCK(hrtc);

  return HAL_OK;

}

#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)

/**

  * @brief  Register a User RTC Callback

  *         To be used instead of the weak predefined callback

  * @param  hrtc RTC handle

  * @param  CallbackID ID of the callback to be registered

  *         This parameter can be one of the following values:

  *          @arg @ref HAL_RTC_ALARM_A_EVENT_CB_ID          Alarm A Event Callback ID

  *          @arg @ref HAL_RTC_TIMESTAMP_EVENT_CB_ID        TimeStamp Event Callback ID

  *          @arg @ref HAL_RTC_WAKEUPTIMER_EVENT_CB_ID      WakeUp Timer Event Callback ID

  *          @arg @ref HAL_RTC_TAMPER1_EVENT_CB_ID          Tamper 1 Callback ID

  *          @arg @ref HAL_RTC_TAMPER2_EVENT_CB_ID          Tamper 2 Callback ID

  *          @arg @ref HAL_RTC_TAMPER3_EVENT_CB_ID          Tamper 3 Callback ID

  *          @arg @ref HAL_RTC_MSPINIT_CB_ID                Msp Init callback ID

  *          @arg @ref HAL_RTC_MSPDEINIT_CB_ID              Msp DeInit callback ID

  * @param  pCallback pointer to the Callback function

  * @retval HAL status

  */

HAL_StatusTypeDef HAL_RTC_RegisterCallback(RTC_HandleTypeDef *hrtc, HAL_RTC_CallbackIDTypeDef CallbackID, pRTC_CallbackTypeDef pCallback)

{

  HAL_StatusTypeDef status = HAL_OK;

  if (pCallback == NULL)

  {

    return HAL_ERROR;

  }

  /* Process locked */

  __HAL_LOCK(hrtc);

  if (HAL_RTC_STATE_READY == hrtc->State)

  {

    switch (CallbackID)

    {

      case HAL_RTC_ALARM_A_EVENT_CB_ID :

        hrtc->AlarmAEventCallback = pCallback;

        break;

      case HAL_RTC_TIMESTAMP_EVENT_CB_ID :

        hrtc->TimeStampEventCallback = pCallback;

        break;

#if defined(RTC_WAKEUP_SUPPORT)

      case HAL_RTC_WAKEUPTIMER_EVENT_CB_ID :

        hrtc->WakeUpTimerEventCallback = pCallback;

        break;

#endif /* RTC_WAKEUP_SUPPORT */

      case HAL_RTC_TAMPER1_EVENT_CB_ID :

        hrtc->Tamper1EventCallback = pCallback;

        break;

      case HAL_RTC_TAMPER2_EVENT_CB_ID :

        hrtc->Tamper2EventCallback = pCallback;

        break;

#if defined(RTC_TAMPER3_SUPPORT)

      case HAL_RTC_TAMPER3_EVENT_CB_ID :

        hrtc->Tamper3EventCallback = pCallback;

        break;

#endif /* RTC_TAMPER3_SUPPORT   */

      case HAL_RTC_MSPINIT_CB_ID :

        hrtc->MspInitCallback = pCallback;

        break;

      case HAL_RTC_MSPDEINIT_CB_ID :

        hrtc->MspDeInitCallback = pCallback;

        break;

      default :

        /* Return error status */

        status =  HAL_ERROR;

        break;

    }

  }

  else if (HAL_RTC_STATE_RESET == hrtc->State)

  {

    switch (CallbackID)

    {

      case HAL_RTC_MSPINIT_CB_ID :

        hrtc->MspInitCallback = pCallback;

        break;

      case HAL_RTC_MSPDEINIT_CB_ID :

        hrtc->MspDeInitCallback = pCallback;

        break;

      default :

        /* Return error status */

        status =  HAL_ERROR;

        break;

    }

  }

  else

  {

    /* Return error status */

    status =  HAL_ERROR;

  }

  /* Release Lock */

  __HAL_UNLOCK(hrtc);

  return status;

}

/**

  * @brief  Unregister an RTC Callback

  *         RTC callabck is redirected to the weak predefined callback

  * @param  hrtc RTC handle

  * @param  CallbackID ID of the callback to be unregistered

  *         This parameter can be one of the following values:

  *          @arg @ref HAL_RTC_ALARM_A_EVENT_CB_ID          Alarm A Event Callback ID

  *          @arg @ref HAL_RTC_TIMESTAMP_EVENT_CB_ID        TimeStamp Event Callback ID

  *          @arg @ref HAL_RTC_WAKEUPTIMER_EVENT_CB_ID      WakeUp Timer Event Callback ID

  *          @arg @ref HAL_RTC_TAMPER1_EVENT_CB_ID          Tamper 1 Callback ID

  *          @arg @ref HAL_RTC_TAMPER2_EVENT_CB_ID          Tamper 2 Callback ID

  *          @arg @ref HAL_RTC_TAMPER3_EVENT_CB_ID          Tamper 3 Callback ID

  *          @arg @ref HAL_RTC_MSPINIT_CB_ID Msp Init callback ID

  *          @arg @ref HAL_RTC_MSPDEINIT_CB_ID Msp DeInit callback ID

  * @retval HAL status

  */

HAL_StatusTypeDef HAL_RTC_UnRegisterCallback(RTC_HandleTypeDef *hrtc, HAL_RTC_CallbackIDTypeDef CallbackID)

{

  HAL_StatusTypeDef status = HAL_OK;

  /* Process locked */

  __HAL_LOCK(hrtc);

  if (HAL_RTC_STATE_READY == hrtc->State)

  {

    switch (CallbackID)

    {

      case HAL_RTC_ALARM_A_EVENT_CB_ID :

        hrtc->AlarmAEventCallback = HAL_RTC_AlarmAEventCallback;         /* Legacy weak AlarmAEventCallback    */

        break;

      case HAL_RTC_TIMESTAMP_EVENT_CB_ID :

        hrtc->TimeStampEventCallback = HAL_RTCEx_TimeStampEventCallback;    /* Legacy weak TimeStampEventCallback    */

        break;

#if defined(RTC_WAKEUP_SUPPORT)

      case HAL_RTC_WAKEUPTIMER_EVENT_CB_ID :

        hrtc->WakeUpTimerEventCallback = HAL_RTCEx_WakeUpTimerEventCallback; /* Legacy weak WakeUpTimerEventCallback */

        break;

#endif  /* RTC_WAKEUP_SUPPORT */

      case HAL_RTC_TAMPER1_EVENT_CB_ID :

        hrtc->Tamper1EventCallback = HAL_RTCEx_Tamper1EventCallback;         /* Legacy weak Tamper1EventCallback   */

        break;

      case HAL_RTC_TAMPER2_EVENT_CB_ID :

        hrtc->Tamper2EventCallback = HAL_RTCEx_Tamper2EventCallback;         /* Legacy weak Tamper2EventCallback         */

        break;

#if defined( RTC_TAMPER3_SUPPORT)

      case HAL_RTC_TAMPER3_EVENT_CB_ID :

        hrtc->Tamper3EventCallback = HAL_RTCEx_Tamper3EventCallback;         /* Legacy weak Tamper3EventCallback         */

        break;

#endif /* RTC_TAMPER3_SUPPORT */

      case HAL_RTC_MSPINIT_CB_ID :

        hrtc->MspInitCallback = HAL_RTC_MspInit;

        break;

      case HAL_RTC_MSPDEINIT_CB_ID :

        hrtc->MspDeInitCallback = HAL_RTC_MspDeInit;

        break;

      default :

        /* Return error status */

        status =  HAL_ERROR;

        break;

    }

  }

  else if (HAL_RTC_STATE_RESET == hrtc->State)

  {

    switch (CallbackID)

    {

      case HAL_RTC_MSPINIT_CB_ID :

        hrtc->MspInitCallback = HAL_RTC_MspInit;

        break;

      case HAL_RTC_MSPDEINIT_CB_ID :

        hrtc->MspDeInitCallback = HAL_RTC_MspDeInit;

        break;

      default :

        /* Return error status */

        status =  HAL_ERROR;

        break;

    }

  }

  else

  {

    /* Return error status */

    status =  HAL_ERROR;

  }

  /* Release Lock */

  __HAL_UNLOCK(hrtc);

  return status;

}

#endif /* USE_HAL_RTC_REGISTER_CALLBACKS */

/**

  * @brief  Initialize the RTC MSP.

  * @param  hrtc RTC handle

  * @retval None

  */

__weak void HAL_RTC_MspInit(RTC_HandleTypeDef *hrtc)

{

  /* Prevent unused argument(s) compilation warning */

  UNUSED(hrtc);

  /* NOTE : This function should not be modified, when the callback is needed,

            the HAL_RTC_MspInit could be implemented in the user file

   */

}

/**

  * @brief  DeInitialize the RTC MSP.

  * @param  hrtc RTC handle

  * @retval None

  */

__weak void HAL_RTC_MspDeInit(RTC_HandleTypeDef *hrtc)

{

  /* Prevent unused argument(s) compilation warning */

  UNUSED(hrtc);

  /* NOTE : This function should not be modified, when the callback is needed,

            the HAL_RTC_MspDeInit could be implemented in the user file

   */

}

/**

  * @}

  */

/** @addtogroup RTC_Exported_Functions_Group2

 *  @brief   RTC Time and Date functions

 *

@verbatim

 ===============================================================================

                 ##### RTC Time and Date functions #####

 ===============================================================================

 [..] This section provides functions allowing to configure Time and Date features

@endverbatim

  * @{

  */

/**

  * @brief  Set RTC current time.

  * @param  hrtc RTC handle

  * @param  sTime Pointer to Time structure

  * @note   DayLightSaving and StoreOperation interfaces are deprecated.

  *         To manage Daylight Saving Time, please use HAL_RTC_DST_xxx functions.

  * @param  Format Specifies the format of the entered parameters.

  *          This parameter can be one of the following values:

  *            @arg RTC_FORMAT_BIN: Binary data format

  *            @arg RTC_FORMAT_BCD: BCD data format

  * @retval HAL status

  */

HAL_StatusTypeDef HAL_RTC_SetTime(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef *sTime, uint32_t Format)

{

  uint32_t tmpreg = 0U;

  /* Check the parameters */

  assert_param(IS_RTC_FORMAT(Format));

  assert_param(IS_RTC_DAYLIGHT_SAVING(sTime->DayLightSaving));

  assert_param(IS_RTC_STORE_OPERATION(sTime->StoreOperation));

  /* Process Locked */

  __HAL_LOCK(hrtc);

  hrtc->State = HAL_RTC_STATE_BUSY;

  if (Format == RTC_FORMAT_BIN)

  {

    if ((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET)

    {

      assert_param(IS_RTC_HOUR12(sTime->Hours));

      assert_param(IS_RTC_HOURFORMAT12(sTime->TimeFormat));

    }

    else

    {

      sTime->TimeFormat = 0x00U;

      assert_param(IS_RTC_HOUR24(sTime->Hours));

    }

    assert_param(IS_RTC_MINUTES(sTime->Minutes));

    assert_param(IS_RTC_SECONDS(sTime->Seconds));

    tmpreg = (uint32_t)(((uint32_t)RTC_ByteToBcd2(sTime->Hours) << 16U) | \

                        ((uint32_t)RTC_ByteToBcd2(sTime->Minutes) << 8U) | \

                        ((uint32_t)RTC_ByteToBcd2(sTime->Seconds)) | \

                        (((uint32_t)sTime->TimeFormat) << 16U));

  }

  else

  {

    if ((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET)

    {

      assert_param(IS_RTC_HOUR12(RTC_Bcd2ToByte(sTime->Hours)));

      assert_param(IS_RTC_HOURFORMAT12(sTime->TimeFormat));

    }

    else

    {

      sTime->TimeFormat = 0x00U;

      assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sTime->Hours)));

    }

    assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sTime->Minutes)));

    assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sTime->Seconds)));

    tmpreg = (((uint32_t)(sTime->Hours) << 16U) | \

              ((uint32_t)(sTime->Minutes) << 8U) | \

              ((uint32_t)sTime->Seconds) | \

              ((uint32_t)(sTime->TimeFormat) << 16U));

  }

  /* Disable the write protection for RTC registers */

  __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);

  /* Set Initialization mode */

  if (RTC_EnterInitMode(hrtc) != HAL_OK)

  {

    /* Enable the write protection for RTC registers */

    __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);

    /* Set RTC state */

    hrtc->State = HAL_RTC_STATE_ERROR;

    /* Process Unlocked */

    __HAL_UNLOCK(hrtc);

    return HAL_ERROR;

  }

  else

  {

    /* Set the RTC_TR register */

    hrtc->Instance->TR = (uint32_t)(tmpreg & RTC_TR_RESERVED_MASK);

    /* Clear the bits to be configured (Deprecated. Use HAL_RTC_DST_xxx functions instead) */

    hrtc->Instance->CR &= ((uint32_t)~RTC_CR_BKP);

    /* Configure the RTC_CR register (Deprecated. Use HAL_RTC_DST_xxx functions instead) */

    hrtc->Instance->CR |= (uint32_t)(sTime->DayLightSaving | sTime->StoreOperation);

    /* Exit Initialization mode */

    hrtc->Instance->ISR &= ((uint32_t)~RTC_ISR_INIT);

    /* If  CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */

    if ((hrtc->Instance->CR & RTC_CR_BYPSHAD) == RESET)

    {

      if (HAL_RTC_WaitForSynchro(hrtc) != HAL_OK)

      {

        /* Enable the write protection for RTC registers */

        __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);

        hrtc->State = HAL_RTC_STATE_ERROR;

        /* Process Unlocked */

        __HAL_UNLOCK(hrtc);

        return HAL_ERROR;

      }

    }

    /* Enable the write protection for RTC registers */

    __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);

    hrtc->State = HAL_RTC_STATE_READY;

    __HAL_UNLOCK(hrtc);

    return HAL_OK;

  }

}

/**

  * @brief  Get RTC current time.

  * @param  hrtc RTC handle

  * @param  sTime Pointer to Time structure with Hours, Minutes and Seconds fields returned

  *                with input format (BIN or BCD), also SubSeconds field returning the

  *                RTC_SSR register content and SecondFraction field the Synchronous pre-scaler

  *                factor to be used for second fraction ratio computation.

  * @param  Format Specifies the format of the entered parameters.

  *          This parameter can be one of the following values:

  *            @arg RTC_FORMAT_BIN: Binary data format

  *            @arg RTC_FORMAT_BCD: BCD data format

  * @note  You can use SubSeconds and SecondFraction (sTime structure fields returned) to convert SubSeconds

  *        value in second fraction ratio with time unit following generic formula:

  *        Second fraction ratio * time_unit= [(SecondFraction-SubSeconds)/(SecondFraction+1)] * time_unit

  *        This conversion can be performed only if no shift operation is pending (ie. SHFP=0) when PREDIV_S >= SS

  * @note You must call HAL_RTC_GetDate() after HAL_RTC_GetTime() to unlock the values

  * in the higher-order calendar shadow registers to ensure consistency between the time and date values.

  * Reading RTC current time locks the values in calendar shadow registers until Current date is read

  * to ensure consistency between the time and date values.

  * @retval HAL status

  */

HAL_StatusTypeDef HAL_RTC_GetTime(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef *sTime, uint32_t Format)

{

  uint32_t tmpreg = 0;

  /* Check the parameters */

  assert_param(IS_RTC_FORMAT(Format));

  /* Get subseconds structure field from the corresponding register*/

  sTime->SubSeconds = (uint32_t)(hrtc->Instance->SSR);

  /* Get SecondFraction structure field from the corresponding register field*/

  sTime->SecondFraction = (uint32_t)(hrtc->Instance->PRER & RTC_PRER_PREDIV_S);

  /* Get the TR register */

  tmpreg = (uint32_t)(hrtc->Instance->TR & RTC_TR_RESERVED_MASK);

  /* Fill the structure fields with the read parameters */

  sTime->Hours = (uint8_t)((tmpreg & (RTC_TR_HT | RTC_TR_HU)) >> 16U);

  sTime->Minutes = (uint8_t)((tmpreg & (RTC_TR_MNT | RTC_TR_MNU)) >> 8U);

  sTime->Seconds = (uint8_t)(tmpreg & (RTC_TR_ST | RTC_TR_SU));

  sTime->TimeFormat = (uint8_t)((tmpreg & (RTC_TR_PM)) >> 16U);

  /* Check the input parameters format */

  if (Format == RTC_FORMAT_BIN)

  {

    /* Convert the time structure parameters to Binary format */

    sTime->Hours = (uint8_t)RTC_Bcd2ToByte(sTime->Hours);

    sTime->Minutes = (uint8_t)RTC_Bcd2ToByte(sTime->Minutes);

    sTime->Seconds = (uint8_t)RTC_Bcd2ToByte(sTime->Seconds);

  }

  return HAL_OK;

}

/**

  * @brief  Set RTC current date.

  * @param  hrtc RTC handle

  * @param  sDate Pointer to date structure

  * @param  Format specifies the format of the entered parameters.

  *          This parameter can be one of the following values:

  *            @arg RTC_FORMAT_BIN: Binary data format

  *            @arg RTC_FORMAT_BCD: BCD data format

  * @retval HAL status

  */

HAL_StatusTypeDef HAL_RTC_SetDate(RTC_HandleTypeDef *hrtc, RTC_DateTypeDef *sDate, uint32_t Format)

{

  uint32_t datetmpreg = 0U;

  /* Check the parameters */

  assert_param(IS_RTC_FORMAT(Format));

  /* Process Locked */

  __HAL_LOCK(hrtc);

  hrtc->State = HAL_RTC_STATE_BUSY;

  if ((Format == RTC_FORMAT_BIN) && ((sDate->Month & 0x10U) == 0x10U))

  {

    sDate->Month = (uint8_t)((sDate->Month & (uint8_t)~(0x10U)) + (uint8_t)0x0AU);