Subversion Repositories dashGPS

#include "main.h"

#include "libNMEA/nmea.h"

#include <cstring>

#include "libOLED/stm32_halDisplay.H"

#include "libOLED/fontclass.H"

#include "libOLED/displayDial.H"

#include "libBMP280/bmp280.h"

#include "libSmallPrintf/small_printf.h"

#if defined USB_DEVICE

#include "usbd_cdc_if.h"

#endif

namespace

{

  int const WIDTH = 128;

  int const HEIGHT = 64;

  int const DISPLAY_RAMWIDTH = 132;

}

float speedMPH = 0.0;

float speedAVG = 0.0;

int speedTimer  = 0;

float speedDist = 0.0;

int heading = 0;

Location loc;

uint32_t lastTick = 0;

int32_t temp32 = 0;

uint32_t pres32 = 0;

int32_t rslt;

uint8_t displayBuffer[dataSize (WIDTH, HEIGHT)];

stm32_halDisplay_t display1 (WIDTH, HEIGHT, DISPLAY_RAMWIDTH, displayBuffer,

                             &hspi1,

                             SPI_CD_GPIO_Port,

                             SPI_CD_Pin,

                             SPI_RESET_GPIO_Port,

                             SPI_RESET_Pin,

                             SPI_NSS1_GPIO_Port,

                             SPI_NSS1_Pin);

displayDial_t dial (display1, 96, 32, 32, 180);

extern "C" void

cc_init ()

{

  display1.reset ();

  display1.init ();

  display1.clearDisplay ();

  dial.draw_scale (0, 360, 8, 1, 45);

  display1.display ();

  memset (loc.time, '-', 6);

}

char fontBuf[] = "01234567";

extern "C" void

cc_run (struct bmp280_dev *bmp)

{

  display1.clearDisplay ();

  dial.draw_scale (0, 360, 8, 1, 45);

  bool stat = updateLocation (&loc, &uc1);

  if (loc.good)

    {

      heading = loc.heading;

      loc.good = false;

    }

  if (loc.valid == 'V')

    memset (loc.time, '-', 6);

  // print out the GMT time at the top of the screen

  display1.gotoxy (0, 0);

  display1.printString (small_font, &loc.time[0], 2, WHITE);

  display1.printString (small_font, ":", 1, WHITE);

  display1.printString (small_font, &loc.time[2], 2, WHITE);

  display1.printString (small_font, ":", 1, WHITE);

  display1.printString (small_font, &loc.time[4], 2, WHITE);

  int dial_ang = heading + 180;

  dial.draw_needle (dial_ang);

  display1.gotoxy (70, 25);

  if (loc.valid == 'A')

    {

      display1.fontDigits (large_font, 3, -1, heading);

    }

  else

    display1.printString (large_font, "GPS?", 4, WHITE);

  if (loc.valid == 'A')

    speedMPH = loc.speed / 1.815;

  display1.gotoxy (0, 8);

  display1.printString (small_font, "Speed", 5, WHITE);

  display1.gotoxy (0, 16);

  display1.fontDigits (large_font, 4, 1, speedMPH * 10);

  display1.gotoxy (0, 32);

  display1.printString (small_font, "Average", 7, WHITE);

  display1.gotoxy (0, 40);

  display1.fontDigits (large_font, 4, 1, speedAVG * 10);

  struct bmp280_uncomp_data ucomp_data;

  if (HAL_GetTick () - lastTick > 100)

    {

      lastTick = HAL_GetTick ();

      /* Reading the raw data from sensor */

      rslt = bmp280_get_uncomp_data (&ucomp_data, bmp);

      if (rslt == BMP280_OK)

        {

          /* Getting the 32 bit compensated temperature */

          rslt = bmp280_get_comp_temp_32bit (&temp32, ucomp_data.uncomp_temp,

                                             bmp);

          rslt = bmp280_get_comp_pres_32bit (&pres32, ucomp_data.uncomp_press,

                                             bmp);

#if defined USB_DEVICE

/*

          *  $--XDR,a,x.x,a,c--c, ..... *hh<CR><LF> \\

              Field Number:

              1) Transducer Type

              2) Measurement Data

              3) Units of measurement

              4) Name of transducer

              x) More of the same

              n) Checksum

              Example:

              $IIXDR,C,19.52,C,TempAir*19

              $IIXDR,P,1.02481,B,Barometer*29

              Currently, OpenCPN recognizes the following transducers:

          Measured Value | Transducer Type | Measured Data   | Unit of measure | Transducer Name

          ------------------------------------------------------------------------------------------------------

          barometric     | "P" pressure    | 0.8..1.1 or 800..1100           | "B" bar         | "Barometer"

          air temperature| "C" temperature |   2 decimals                    | "C" celsius     | "TempAir" or "ENV_OUTAIR_T"

          pitch          | "A" angle       |-180..0 nose down 0..180 nose up | "D" degrees     | "PTCH" or "PITCH"

          rolling        | "A" angle       |-180..0 L         0..180 R       | "D" degrees     | "ROLL"

          water temp     | "C" temperature |   2 decimals                    | "C" celsius     | "ENV_WATER_T"

*/

          // compile a logger message over USB

           char buffer[200];

           int cnt = small_sprintf(buffer,"$MJXDR,C,%ld.%02ld,C,AirTemp,P,%01ld.%05ld,B,AirPres",temp32/100,temp32%100,pres32/100000,pres32%100000);

           uint8_t sum=0;

           for(int i=1; i<cnt; i++)

             sum += buffer[i];

           cnt+= small_sprintf(buffer+cnt,"*%02X\n",sum);

           CDC_Transmit_FS(reinterpret_cast<uint8_t*>(&buffer[0]),cnt);

#endif

        }

    }

  display1.gotoxy (0, 56);

  display1.printString (small_font, "T", 2, WHITE);

  display1.fontDigits (small_font, 4, 1, temp32/10, WHITE);

  display1.printString (small_font, " P", 2, WHITE);

  display1.fontDigits (small_font, 5, 0, pres32/100, WHITE);

  display1.printString (small_font, " ", 1, WHITE);

  display1.display ();

}