WebSVN – DashDisplay – Blame – /branches/Dashboard_L152_v2/Drivers/STM32L1xx_HAL_Driver/Src/stm32l1xx_hal_rcc.c

Rev	Author	Line No.	Line
30	mjames	1	/**
		2	******************************************************************************
		3	* @file stm32l1xx_hal_rcc.c
		4	* @author MCD Application Team
		5	* @brief RCC HAL module driver.
50	mjames	6	* This file provides firmware functions to manage the following
30	mjames	7	* functionalities of the Reset and Clock Control (RCC) peripheral:
		8	* + Initialization and de-initialization functions
		9	* + Peripheral Control functions
50	mjames	10	*
		11	@verbatim
30	mjames	12	==============================================================================
		13	##### RCC specific features #####
		14	==============================================================================
50	mjames	15	[..]
		16	After reset the device is running from multispeed internal oscillator clock
		17	(MSI 2.097MHz) with Flash 0 wait state and Flash prefetch buffer is disabled,
30	mjames	18	and all peripherals are off except internal SRAM, Flash and JTAG.
		19	(+) There is no prescaler on High speed (AHB) and Low speed (APB) buses;
		20	all peripherals mapped on these buses are running at MSI speed.
		21	(+) The clock for all peripherals is switched off, except the SRAM and FLASH.
		22	(+) All GPIOs are in input floating state, except the JTAG pins which
		23	are assigned to be used for debug purpose.
		24	[..] Once the device started from reset, the user application has to:
		25	(+) Configure the clock source to be used to drive the System clock
		26	(if the application needs higher frequency/performance)
50	mjames	27	(+) Configure the System clock frequency and Flash settings
30	mjames	28	(+) Configure the AHB and APB buses prescalers
		29	(+) Enable the clock for the peripheral(s) to be used
		30	(+) Configure the clock source(s) for peripherals whose clocks are not
50	mjames	31	derived from the System clock (I2S, RTC, ADC, USB OTG FS/SDIO/RNG)
30	mjames	32	(*) SDIO only for STM32L1xxxD devices
		33
		34	##### RCC Limitations #####
		35	==============================================================================
50	mjames	36	[..]
		37	A delay between an RCC peripheral clock enable and the effective peripheral
		38	enabling should be taken into account in order to manage the peripheral read/write
30	mjames	39	from/to registers.
		40	(+) This delay depends on the peripheral mapping.
		41	(++) AHB & APB peripherals, 1 dummy read is necessary
		42
50	mjames	43	[..]
30	mjames	44	Workarounds:
		45	(#) For AHB & APB peripherals, a dummy read to the peripheral register has been
		46	inserted in each __HAL_RCC_PPP_CLK_ENABLE() macro.
		47
		48	@endverbatim
		49	******************************************************************************
		50	* @attention
		51	*
50	mjames	52	* <h2><center>© Copyright(c) 2017 STMicroelectronics.
		53	* All rights reserved.</center></h2>
30	mjames	54	*
50	mjames	55	* This software component is licensed by ST under BSD 3-Clause license,
		56	* the "License"; You may not use this file except in compliance with the
		57	* License. You may obtain a copy of the License at:
		58	* opensource.org/licenses/BSD-3-Clause
30	mjames	59	*
50	mjames	60	******************************************************************************
		61	*/
30	mjames	62
		63	/* Includes ------------------------------------------------------------------*/
		64	#include "stm32l1xx_hal.h"
		65
		66	/** @addtogroup STM32L1xx_HAL_Driver
		67	* @{
		68	*/
		69
		70	/** @defgroup RCC RCC
		71	* @brief RCC HAL module driver
		72	* @{
		73	*/
		74
		75	#ifdef HAL_RCC_MODULE_ENABLED
		76
		77	/* Private typedef -----------------------------------------------------------*/
		78	/* Private define ------------------------------------------------------------*/
		79	/* Private macro -------------------------------------------------------------*/
		80	/** @defgroup RCC_Private_Macros RCC Private Macros
		81	* @{
		82	*/
		83
		84	#define MCO1_CLK_ENABLE() __HAL_RCC_GPIOA_CLK_ENABLE()
		85	#define MCO1_GPIO_PORT GPIOA
		86	#define MCO1_PIN GPIO_PIN_8
		87
		88	/**
		89	* @}
		90	*/
		91
		92	/* Private variables ---------------------------------------------------------*/
		93	/** @defgroup RCC_Private_Variables RCC Private Variables
		94	* @{
		95	*/
		96	extern const uint8_t PLLMulTable[]; /* Defined in CMSIS (system_stm32l0xx.c)*/
		97	/**
		98	* @}
		99	*/
		100
		101	/* Private function prototypes -----------------------------------------------*/
		102	/** @defgroup RCC_Private_Functions RCC Private Functions
		103	* @{
		104	*/
		105	static HAL_StatusTypeDef RCC_SetFlashLatencyFromMSIRange(uint32_t MSIrange);
		106	/**
		107	* @}
		108	*/
		109
		110	/* Exported functions ---------------------------------------------------------*/
		111
		112	/** @defgroup RCC_Exported_Functions RCC Exported Functions
		113	* @{
		114	*/
		115
50	mjames	116	/** @defgroup RCC_Exported_Functions_Group1 Initialization and de-initialization functions
		117	* @brief Initialization and Configuration functions
30	mjames	118	*
50	mjames	119	@verbatim
30	mjames	120	===============================================================================
		121	##### Initialization and de-initialization functions #####
		122	===============================================================================
		123	[..]
		124	This section provides functions allowing to configure the internal/external oscillators
50	mjames	125	(MSI, HSE, HSI, LSE, LSI, PLL, CSS and MCO) and the System buses clocks (SYSCLK, AHB, APB1
30	mjames	126	and APB2).
		127
		128	[..] Internal/external clock and PLL configuration
50	mjames	129	(#) MSI (Multispeed internal), Seven frequency ranges are available: 65.536 kHz,
30	mjames	130	131.072 kHz, 262.144 kHz, 524.288 kHz, 1.048 MHz, 2.097 MHz (default value) and 4.194 MHz.
		131
		132	(#) HSI (high-speed internal), 16 MHz factory-trimmed RC used directly or through
		133	the PLL as System clock source.
		134	(#) LSI (low-speed internal), ~37 KHz low consumption RC used as IWDG and/or RTC
		135	clock source.
		136
		137	(#) HSE (high-speed external), 1 to 24 MHz crystal oscillator used directly or
		138	through the PLL as System clock source. Can be used also as RTC clock source.
		139
50	mjames	140	(#) LSE (low-speed external), 32 KHz oscillator used as RTC clock source.
30	mjames	141
		142	(#) PLL (clocked by HSI or HSE), featuring different output clocks:
		143	(++) The first output is used to generate the high speed system clock (up to 32 MHz)
		144	(++) The second output is used to generate the clock for the USB OTG FS (48 MHz)
		145
		146	(#) CSS (Clock security system), once enable using the macro __HAL_RCC_CSS_ENABLE()
50	mjames	147	and if a HSE clock failure occurs(HSE used directly or through PLL as System
30	mjames	148	clock source), the System clocks automatically switched to MSI and an interrupt
50	mjames	149	is generated if enabled. The interrupt is linked to the Cortex-M3 NMI
		150	(Non-Maskable Interrupt) exception vector.
30	mjames	151
50	mjames	152	(#) MCO1 (microcontroller clock output), used to output SYSCLK, HSI, LSI, MSI, LSE,
30	mjames	153	HSE or PLL clock (through a configurable prescaler) on PA8 pin.
		154
		155	[..] System, AHB and APB buses clocks configuration
		156	(#) Several clock sources can be used to drive the System clock (SYSCLK): MSI, HSI,
		157	HSE and PLL.
		158	The AHB clock (HCLK) is derived from System clock through configurable
		159	prescaler and used to clock the CPU, memory and peripherals mapped
		160	on AHB bus (DMA, GPIO...). APB1 (PCLK1) and APB2 (PCLK2) clocks are derived
		161	from AHB clock through configurable prescalers and used to clock
		162	the peripherals mapped on these buses. You can use
		163	"@ref HAL_RCC_GetSysClockFreq()" function to retrieve the frequencies of these clocks.
		164
		165	-@- All the peripheral clocks are derived from the System clock (SYSCLK) except:
		166	(+@) RTC: RTC clock can be derived either from the LSI, LSE or HSE clock
		167	divided by 2 to 16. You have to use @ref __HAL_RCC_RTC_CONFIG() and @ref __HAL_RCC_RTC_ENABLE()
50	mjames	168	macros to configure this clock.
30	mjames	169	(+@) LCD: LCD clock can be derived either from the LSI, LSE or HSE clock
		170	divided by 2 to 16. You have to use @ref __HAL_RCC_LCD_CONFIG()
50	mjames	171	macros to configure this clock.
30	mjames	172	(+@) USB OTG FS: USB OTG FS require a frequency equal to 48 MHz
		173	to work correctly. This clock is derived of the main PLL through PLL Multiplier.
		174
		175	(+@) IWDG clock which is always the LSI clock.
		176
50	mjames	177	(#) The maximum frequency of the SYSCLK and HCLK is 32 MHz, PCLK2 32 MHz
		178	and PCLK1 32 MHz. Depending on the device voltage range, the maximum
30	mjames	179	frequency should be adapted accordingly.
		180	@endverbatim
		181	* @{
		182	*/
50	mjames	183
30	mjames	184	/*
		185	Additional consideration on the HCLK based on Latency settings:
50	mjames	186	+----------------------------------------------------------------------+
30	mjames	187	\| Latency \| HCLK clock frequency (MHz) \|
50	mjames	188	\| \|------------------------------------------------------\|
30	mjames	189	\| \| voltage range 1 \| voltage range 2 \| voltage range 3 \|
		190	\| \| 1.8 V \| 1.5 V \| 1.2 V \|
50	mjames	191	\|---------------\|------------------\|-----------------\|-----------------\|
30	mjames	192	\|0WS(1CPU cycle)\| 0 < HCLK <= 16 \| 0 < HCLK <= 8 \| 0 < HCLK <= 2 \|
50	mjames	193	\|---------------\|------------------\|-----------------\|-----------------\|
		194	\|1WS(2CPU cycle)\| 16 < HCLK <= 32 \| 8 < HCLK <= 16 \| 2 < HCLK <= 4 \|
		195	+----------------------------------------------------------------------+
30	mjames	196
		197	The following table gives the different clock source frequencies depending on the product
		198	voltage range:
50	mjames	199	+------------------------------------------------------------------------------------------+
30	mjames	200	\| Product voltage \| Clock frequency \|
50	mjames	201	\| \|------------------\|-----------------------------\|-----------------------\|
30	mjames	202	\| range \| MSI \| HSI \| HSE \| PLL \|
50	mjames	203	\|-----------------\|---------\|--------\|-----------------------------\|-----------------------\|
30	mjames	204	\| Range 1 (1.8 V) \| 4.2 MHz \| 16 MHz \| HSE 32 MHz (external clock) \| 32 MHz \|
		205	\| \| \| \| or 24 MHz (crystal) \| (PLLVCO max = 96 MHz) \|
50	mjames	206	\|-----------------\|---------\|--------\|-----------------------------\|-----------------------\|
30	mjames	207	\| Range 2 (1.5 V) \| 4.2 MHz \| 16 MHz \| 16 MHz \| 16 MHz \|
		208	\| \| \| \| \| (PLLVCO max = 48 MHz) \|
50	mjames	209	\|-----------------\|---------\|--------\|-----------------------------\|-----------------------\|
30	mjames	210	\| Range 3 (1.2 V) \| 4.2 MHz \| NA \| 8 MHz \| 4 MHz \|
		211	\| \| \| \| \| (PLLVCO max = 24 MHz) \|
50	mjames	212	+------------------------------------------------------------------------------------------+
30	mjames	213	*/
		214
		215	/**
		216	* @brief Resets the RCC clock configuration to the default reset state.
		217	* @note The default reset state of the clock configuration is given below:
		218	* - MSI ON and used as system clock source
		219	* - HSI, HSE and PLL OFF
		220	* - AHB, APB1 and APB2 prescaler set to 1.
		221	* - CSS and MCO1 OFF
		222	* - All interrupts disabled
		223	* @note This function does not modify the configuration of the
		224	* - Peripheral clocks
		225	* - LSI, LSE and RTC clocks
50	mjames	226	* @retval HAL status
30	mjames	227	*/
50	mjames	228	HAL_StatusTypeDef HAL_RCC_DeInit(void)
30	mjames	229	{
50	mjames	230	uint32_t tickstart;
		231	HAL_StatusTypeDef status;
		232
		233	/* Set MSIClockRange, HSITRIM and MSITRIM bits to the reset values */
		234	MODIFY_REG(RCC->ICSCR, (RCC_ICSCR_MSITRIM \| RCC_ICSCR_HSITRIM \| RCC_ICSCR_MSIRANGE), \
		235	((RCC_MSICALIBRATION_DEFAULT << RCC_ICSCR_MSITRIM_Pos) \| (RCC_HSICALIBRATION_DEFAULT << RCC_ICSCR_HSITRIM_Pos) \| RCC_ICSCR_MSIRANGE_5));
		236
30	mjames	237	/* Set MSION bit */
		238	SET_BIT(RCC->CR, RCC_CR_MSION);
50	mjames	239
		240	/* Get Start Tick*/
		241	tickstart = HAL_GetTick();
		242
		243	/* Wait till MSI is ready */
		244	while (READ_BIT(RCC->CR, RCC_CR_MSIRDY) == 0U)
		245	{
		246	if ((HAL_GetTick() - tickstart) > MSI_TIMEOUT_VALUE)
		247	{
		248	return HAL_TIMEOUT;
		249	}
		250	}
		251
30	mjames	252	/* Switch SYSCLK to MSI*/
		253	CLEAR_BIT(RCC->CFGR, RCC_CFGR_SW);
		254
50	mjames	255	/* Wait till MSI as SYSCLK status is ready */
		256	while (READ_BIT(RCC->CFGR, RCC_CFGR_SWS) != 0U)
		257	{
		258	if ((HAL_GetTick() - tickstart) > CLOCKSWITCH_TIMEOUT_VALUE)
		259	{
		260	return HAL_TIMEOUT;
		261	}
		262	}
		263
		264	/* Update the SystemCoreClock global variable */
		265	SystemCoreClock = MSI_VALUE;
		266
		267	/* Configure the source of time base considering new system clock settings */
		268	status = HAL_InitTick(uwTickPrio);
		269	if(status != HAL_OK)
		270	{
		271	return status;
		272	}
		273
		274	/* Reset HSION, HSEON, CSSON & PLLON bits */
		275	CLEAR_BIT(RCC->CR, RCC_CR_HSION \| RCC_CR_HSEON \| RCC_CR_CSSON \| RCC_CR_PLLON);
		276	/* Reset HSEBYP bit */
		277	CLEAR_BIT(RCC->CR, RCC_CR_HSEBYP);
		278
		279	/* Get Start Tick*/
		280	tickstart = HAL_GetTick();
		281
		282	/* Wait till PLL is not ready */
		283	while (READ_BIT(RCC->CR, RCC_CR_PLLRDY) != 0U)
		284	{
		285	if ((HAL_GetTick() - tickstart) > PLL_TIMEOUT_VALUE)
		286	{
		287	return HAL_TIMEOUT;
		288	}
		289	}
		290
30	mjames	291	/* Reset CFGR register */
		292	CLEAR_REG(RCC->CFGR);
50	mjames	293
30	mjames	294	/* Disable all interrupts */
		295	CLEAR_REG(RCC->CIR);
		296
50	mjames	297	/* Clear all flags */
		298	#if defined(RCC_LSECSS_SUPPORT)
		299	WRITE_REG(RCC->CIR, RCC_CIR_LSIRDYC \| RCC_CIR_LSERDYC \| RCC_CIR_HSIRDYC \| RCC_CIR_HSERDYC \| RCC_CIR_PLLRDYC \| RCC_CIR_MSIRDYC \| RCC_CIR_LSECSSC \| RCC_CIR_CSSC);
		300	#else
		301	WRITE_REG(RCC->CIR, RCC_CIR_LSIRDYC \| RCC_CIR_LSERDYC \| RCC_CIR_HSIRDYC \| RCC_CIR_HSERDYC \| RCC_CIR_PLLRDYC \| RCC_CIR_MSIRDYC \| RCC_CIR_CSSC);
		302	#endif
		303
		304	/* Clear all reset flags */
		305	SET_BIT(RCC->CSR, RCC_CSR_RMVF);
		306
		307	return HAL_OK;
30	mjames	308	}
		309
		310	/**
		311	* @brief Initializes the RCC Oscillators according to the specified parameters in the
		312	* RCC_OscInitTypeDef.
		313	* @param RCC_OscInitStruct pointer to an RCC_OscInitTypeDef structure that
		314	* contains the configuration information for the RCC Oscillators.
		315	* @note The PLL is not disabled when used as system clock.
		316	* @note Transitions LSE Bypass to LSE On and LSE On to LSE Bypass are not
		317	* supported by this macro. User should request a transition to LSE Off
		318	* first and then LSE On or LSE Bypass.
		319	* @note Transition HSE Bypass to HSE On and HSE On to HSE Bypass are not
		320	* supported by this macro. User should request a transition to HSE Off
		321	* first and then HSE On or HSE Bypass.
		322	* @retval HAL status
		323	*/
		324	HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct)
		325	{
50	mjames	326	uint32_t tickstart;
		327	HAL_StatusTypeDef status;
		328	uint32_t sysclk_source, pll_config;
		329
30	mjames	330	/* Check the parameters */
50	mjames	331	if(RCC_OscInitStruct == NULL)
		332	{
		333	return HAL_ERROR;
		334	}
		335
30	mjames	336	assert_param(IS_RCC_OSCILLATORTYPE(RCC_OscInitStruct->OscillatorType));
		337
50	mjames	338	sysclk_source = __HAL_RCC_GET_SYSCLK_SOURCE();
		339	pll_config = __HAL_RCC_GET_PLL_OSCSOURCE();
		340
		341	/------------------------------- HSE Configuration ------------------------/
30	mjames	342	if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSE) == RCC_OSCILLATORTYPE_HSE)
		343	{
		344	/* Check the parameters */
		345	assert_param(IS_RCC_HSE(RCC_OscInitStruct->HSEState));
		346
		347	/* When the HSE is used as system clock or clock source for PLL in these cases it is not allowed to be disabled */
50	mjames	348	if((sysclk_source == RCC_SYSCLKSOURCE_STATUS_HSE)
		349	\|\| ((sysclk_source == RCC_SYSCLKSOURCE_STATUS_PLLCLK) && (pll_config == RCC_PLLSOURCE_HSE)))
30	mjames	350	{
50	mjames	351	if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != 0U) && (RCC_OscInitStruct->HSEState == RCC_HSE_OFF))
30	mjames	352	{
		353	return HAL_ERROR;
		354	}
		355	}
		356	else
		357	{
		358	/* Set the new HSE configuration ---------------------------------------*/
		359	__HAL_RCC_HSE_CONFIG(RCC_OscInitStruct->HSEState);
		360
50	mjames	361	/* Check the HSE State */
30	mjames	362	if(RCC_OscInitStruct->HSEState != RCC_HSE_OFF)
		363	{
		364	/* Get Start Tick */
		365	tickstart = HAL_GetTick();
50	mjames	366
30	mjames	367	/* Wait till HSE is ready */
50	mjames	368	while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == 0U)
30	mjames	369	{
		370	if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE)
		371	{
		372	return HAL_TIMEOUT;
		373	}
		374	}
		375	}
		376	else
		377	{
		378	/* Get Start Tick */
		379	tickstart = HAL_GetTick();
50	mjames	380
30	mjames	381	/* Wait till HSE is disabled */
50	mjames	382	while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != 0U)
30	mjames	383	{
		384	if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE)
		385	{
		386	return HAL_TIMEOUT;
		387	}
		388	}
		389	}
		390	}
		391	}
50	mjames	392	/----------------------------- HSI Configuration --------------------------/
30	mjames	393	if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSI) == RCC_OSCILLATORTYPE_HSI)
		394	{
		395	/* Check the parameters */
		396	assert_param(IS_RCC_HSI(RCC_OscInitStruct->HSIState));
		397	assert_param(IS_RCC_CALIBRATION_VALUE(RCC_OscInitStruct->HSICalibrationValue));
50	mjames	398
		399	/* Check if HSI is used as system clock or as PLL source when PLL is selected as system clock */
		400	if((sysclk_source == RCC_SYSCLKSOURCE_STATUS_HSI)
		401	\|\| ((sysclk_source == RCC_SYSCLKSOURCE_STATUS_PLLCLK) && (pll_config == RCC_PLLSOURCE_HSI)))
30	mjames	402	{
		403	/* When HSI is used as system clock it will not disabled */
50	mjames	404	if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != 0U) && (RCC_OscInitStruct->HSIState != RCC_HSI_ON))
30	mjames	405	{
		406	return HAL_ERROR;
		407	}
		408	/* Otherwise, just the calibration is allowed */
		409	else
		410	{
		411	/* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/
		412	__HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue);
		413	}
		414	}
		415	else
		416	{
		417	/* Check the HSI State */
		418	if(RCC_OscInitStruct->HSIState != RCC_HSI_OFF)
		419	{
50	mjames	420	/* Enable the Internal High Speed oscillator (HSI). */
30	mjames	421	__HAL_RCC_HSI_ENABLE();
50	mjames	422
30	mjames	423	/* Get Start Tick */
		424	tickstart = HAL_GetTick();
50	mjames	425
30	mjames	426	/* Wait till HSI is ready */
50	mjames	427	while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == 0U)
30	mjames	428	{
		429	if((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE)
		430	{
		431	return HAL_TIMEOUT;
		432	}
		433	}
50	mjames	434
30	mjames	435	/* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/
		436	__HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue);
		437	}
		438	else
		439	{
		440	/* Disable the Internal High Speed oscillator (HSI). */
		441	__HAL_RCC_HSI_DISABLE();
50	mjames	442
30	mjames	443	/* Get Start Tick */
		444	tickstart = HAL_GetTick();
50	mjames	445
30	mjames	446	/* Wait till HSI is disabled */
50	mjames	447	while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != 0U)
30	mjames	448	{
		449	if((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE)
		450	{
		451	return HAL_TIMEOUT;
		452	}
		453	}
		454	}
		455	}
		456	}
50	mjames	457	/----------------------------- MSI Configuration --------------------------/
30	mjames	458	if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_MSI) == RCC_OSCILLATORTYPE_MSI)
		459	{
		460	/* When the MSI is used as system clock it will not be disabled */
50	mjames	461	if(sysclk_source == RCC_CFGR_SWS_MSI)
30	mjames	462	{
50	mjames	463	if((__HAL_RCC_GET_FLAG(RCC_FLAG_MSIRDY) != 0U) && (RCC_OscInitStruct->MSIState == RCC_MSI_OFF))
30	mjames	464	{
		465	return HAL_ERROR;
		466	}
		467	/* Otherwise, just the calibration and MSI range change are allowed */
		468	else
		469	{
		470	/* Check MSICalibrationValue and MSIClockRange input parameters */
		471	assert_param(IS_RCC_MSICALIBRATION_VALUE(RCC_OscInitStruct->MSICalibrationValue));
		472	assert_param(IS_RCC_MSI_CLOCK_RANGE(RCC_OscInitStruct->MSIClockRange));
		473
		474	/* To correctly read data from FLASH memory, the number of wait states (LATENCY)
		475	must be correctly programmed according to the frequency of the CPU clock
		476	(HCLK) and the supply voltage of the device. */
		477	if(RCC_OscInitStruct->MSIClockRange > __HAL_RCC_GET_MSI_RANGE())
		478	{
		479	/* First increase number of wait states update if necessary */
		480	if(RCC_SetFlashLatencyFromMSIRange(RCC_OscInitStruct->MSIClockRange) != HAL_OK)
		481	{
		482	return HAL_ERROR;
		483	}
		484
		485	/* Selects the Multiple Speed oscillator (MSI) clock range .*/
		486	__HAL_RCC_MSI_RANGE_CONFIG(RCC_OscInitStruct->MSIClockRange);
		487	/* Adjusts the Multiple Speed oscillator (MSI) calibration value.*/
		488	__HAL_RCC_MSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->MSICalibrationValue);
		489	}
		490	else
		491	{
		492	/* Else, keep current flash latency while decreasing applies */
		493	/* Selects the Multiple Speed oscillator (MSI) clock range .*/
		494	__HAL_RCC_MSI_RANGE_CONFIG(RCC_OscInitStruct->MSIClockRange);
		495	/* Adjusts the Multiple Speed oscillator (MSI) calibration value.*/
		496	__HAL_RCC_MSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->MSICalibrationValue);
		497
		498	/* Decrease number of wait states update if necessary */
		499	if(RCC_SetFlashLatencyFromMSIRange(RCC_OscInitStruct->MSIClockRange) != HAL_OK)
		500	{
		501	return HAL_ERROR;
50	mjames	502	}
30	mjames	503	}
		504
		505	/* Update the SystemCoreClock global variable */
50	mjames	506	SystemCoreClock = (32768U * (1UL << ((RCC_OscInitStruct->MSIClockRange >> RCC_ICSCR_MSIRANGE_Pos) + 1U)))
		507	>> AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> RCC_CFGR_HPRE_Pos)];
30	mjames	508
		509	/* Configure the source of time base considering new system clocks settings*/
50	mjames	510	status = HAL_InitTick(uwTickPrio);
		511	if(status != HAL_OK)
		512	{
		513	return status;
		514	}
30	mjames	515	}
		516	}
		517	else
		518	{
		519	/* Check MSI State */
		520	assert_param(IS_RCC_MSI(RCC_OscInitStruct->MSIState));
		521
		522	/* Check the MSI State */
		523	if(RCC_OscInitStruct->MSIState != RCC_MSI_OFF)
		524	{
		525	/* Enable the Multi Speed oscillator (MSI). */
		526	__HAL_RCC_MSI_ENABLE();
		527
		528	/* Get Start Tick */
		529	tickstart = HAL_GetTick();
		530
		531	/* Wait till MSI is ready */
50	mjames	532	while(__HAL_RCC_GET_FLAG(RCC_FLAG_MSIRDY) == 0U)
30	mjames	533	{
		534	if((HAL_GetTick() - tickstart) > MSI_TIMEOUT_VALUE)
		535	{
		536	return HAL_TIMEOUT;
		537	}
		538	}
		539	/* Check MSICalibrationValue and MSIClockRange input parameters */
		540	assert_param(IS_RCC_MSICALIBRATION_VALUE(RCC_OscInitStruct->MSICalibrationValue));
		541	assert_param(IS_RCC_MSI_CLOCK_RANGE(RCC_OscInitStruct->MSIClockRange));
		542
		543	/* Selects the Multiple Speed oscillator (MSI) clock range .*/
		544	__HAL_RCC_MSI_RANGE_CONFIG(RCC_OscInitStruct->MSIClockRange);
		545	/* Adjusts the Multiple Speed oscillator (MSI) calibration value.*/
		546	__HAL_RCC_MSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->MSICalibrationValue);
		547
		548	}
		549	else
		550	{
		551	/* Disable the Multi Speed oscillator (MSI). */
		552	__HAL_RCC_MSI_DISABLE();
		553
		554	/* Get Start Tick */
		555	tickstart = HAL_GetTick();
		556
		557	/* Wait till MSI is ready */
50	mjames	558	while(__HAL_RCC_GET_FLAG(RCC_FLAG_MSIRDY) != 0U)
30	mjames	559	{
		560	if((HAL_GetTick() - tickstart) > MSI_TIMEOUT_VALUE)
		561	{
		562	return HAL_TIMEOUT;
		563	}
		564	}
		565	}
		566	}
50	mjames	567	}
		568	/------------------------------ LSI Configuration -------------------------/
30	mjames	569	if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSI) == RCC_OSCILLATORTYPE_LSI)
		570	{
		571	/* Check the parameters */
		572	assert_param(IS_RCC_LSI(RCC_OscInitStruct->LSIState));
50	mjames	573
30	mjames	574	/* Check the LSI State */
		575	if(RCC_OscInitStruct->LSIState != RCC_LSI_OFF)
		576	{
		577	/* Enable the Internal Low Speed oscillator (LSI). */
		578	__HAL_RCC_LSI_ENABLE();
50	mjames	579
30	mjames	580	/* Get Start Tick */
		581	tickstart = HAL_GetTick();
50	mjames	582
		583	/* Wait till LSI is ready */
		584	while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) == 0U)
30	mjames	585	{
		586	if((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE)
		587	{
		588	return HAL_TIMEOUT;
		589	}
		590	}
		591	}
		592	else
		593	{
		594	/* Disable the Internal Low Speed oscillator (LSI). */
		595	__HAL_RCC_LSI_DISABLE();
50	mjames	596
30	mjames	597	/* Get Start Tick */
		598	tickstart = HAL_GetTick();
50	mjames	599
		600	/* Wait till LSI is disabled */
		601	while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) != 0U)
30	mjames	602	{
		603	if((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE)
		604	{
		605	return HAL_TIMEOUT;
		606	}
		607	}
		608	}
		609	}
50	mjames	610	/------------------------------ LSE Configuration -------------------------/
30	mjames	611	if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSE) == RCC_OSCILLATORTYPE_LSE)
		612	{
		613	FlagStatus pwrclkchanged = RESET;
50	mjames	614
30	mjames	615	/* Check the parameters */
		616	assert_param(IS_RCC_LSE(RCC_OscInitStruct->LSEState));
		617
		618	/* Update LSE configuration in Backup Domain control register */
		619	/* Requires to enable write access to Backup Domain of necessary */
		620	if(__HAL_RCC_PWR_IS_CLK_DISABLED())
		621	{
		622	__HAL_RCC_PWR_CLK_ENABLE();
		623	pwrclkchanged = SET;
		624	}
50	mjames	625
30	mjames	626	if(HAL_IS_BIT_CLR(PWR->CR, PWR_CR_DBP))
		627	{
		628	/* Enable write access to Backup domain */
		629	SET_BIT(PWR->CR, PWR_CR_DBP);
50	mjames	630
30	mjames	631	/* Wait for Backup domain Write protection disable */
		632	tickstart = HAL_GetTick();
		633
		634	while(HAL_IS_BIT_CLR(PWR->CR, PWR_CR_DBP))
		635	{
		636	if((HAL_GetTick() - tickstart) > RCC_DBP_TIMEOUT_VALUE)
		637	{
		638	return HAL_TIMEOUT;
		639	}
		640	}
		641	}
		642
		643	/* Set the new LSE configuration -----------------------------------------*/
		644	__HAL_RCC_LSE_CONFIG(RCC_OscInitStruct->LSEState);
		645	/* Check the LSE State */
		646	if(RCC_OscInitStruct->LSEState != RCC_LSE_OFF)
		647	{
		648	/* Get Start Tick */
		649	tickstart = HAL_GetTick();
50	mjames	650
		651	/* Wait till LSE is ready */
		652	while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == 0U)
30	mjames	653	{
		654	if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE)
		655	{
		656	return HAL_TIMEOUT;
		657	}
		658	}
		659	}
		660	else
		661	{
		662	/* Get Start Tick */
		663	tickstart = HAL_GetTick();
50	mjames	664
		665	/* Wait till LSE is disabled */
		666	while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) != 0U)
30	mjames	667	{
		668	if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE)
		669	{
		670	return HAL_TIMEOUT;
		671	}
		672	}
		673	}
		674
		675	/* Require to disable power clock if necessary */
		676	if(pwrclkchanged == SET)
		677	{
		678	__HAL_RCC_PWR_CLK_DISABLE();
		679	}
		680	}
		681
		682	/-------------------------------- PLL Configuration -----------------------/
		683	/* Check the parameters */
		684	assert_param(IS_RCC_PLL(RCC_OscInitStruct->PLL.PLLState));
		685	if ((RCC_OscInitStruct->PLL.PLLState) != RCC_PLL_NONE)
		686	{
		687	/* Check if the PLL is used as system clock or not */
50	mjames	688	if(sysclk_source != RCC_SYSCLKSOURCE_STATUS_PLLCLK)
		689	{
30	mjames	690	if((RCC_OscInitStruct->PLL.PLLState) == RCC_PLL_ON)
		691	{
		692	/* Check the parameters */
		693	assert_param(IS_RCC_PLLSOURCE(RCC_OscInitStruct->PLL.PLLSource));
		694	assert_param(IS_RCC_PLL_MUL(RCC_OscInitStruct->PLL.PLLMUL));
		695	assert_param(IS_RCC_PLL_DIV(RCC_OscInitStruct->PLL.PLLDIV));
50	mjames	696
30	mjames	697	/* Disable the main PLL. */
		698	__HAL_RCC_PLL_DISABLE();
50	mjames	699
30	mjames	700	/* Get Start Tick */
		701	tickstart = HAL_GetTick();
50	mjames	702
30	mjames	703	/* Wait till PLL is disabled */
50	mjames	704	while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != 0U)
30	mjames	705	{
		706	if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE)
		707	{
		708	return HAL_TIMEOUT;
		709	}
		710	}
		711
		712	/* Configure the main PLL clock source, multiplication and division factors. */
		713	__HAL_RCC_PLL_CONFIG(RCC_OscInitStruct->PLL.PLLSource,
		714	RCC_OscInitStruct->PLL.PLLMUL,
		715	RCC_OscInitStruct->PLL.PLLDIV);
		716	/* Enable the main PLL. */
		717	__HAL_RCC_PLL_ENABLE();
50	mjames	718
30	mjames	719	/* Get Start Tick */
		720	tickstart = HAL_GetTick();
50	mjames	721
30	mjames	722	/* Wait till PLL is ready */
50	mjames	723	while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == 0U)
30	mjames	724	{
		725	if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE)
		726	{
		727	return HAL_TIMEOUT;
		728	}
		729	}
		730	}
		731	else
		732	{
		733	/* Disable the main PLL. */
		734	__HAL_RCC_PLL_DISABLE();
50	mjames	735
30	mjames	736	/* Get Start Tick */
		737	tickstart = HAL_GetTick();
50	mjames	738
		739	/* Wait till PLL is disabled */
		740	while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != 0U)
30	mjames	741	{
		742	if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE)
		743	{
		744	return HAL_TIMEOUT;
		745	}
		746	}
		747	}
		748	}
		749	else
		750	{
50	mjames	751	/* Check if there is a request to disable the PLL used as System clock source */
		752	if((RCC_OscInitStruct->PLL.PLLState) == RCC_PLL_OFF)
		753	{
		754	return HAL_ERROR;
		755	}
		756	else
		757	{
		758	/* Do not return HAL_ERROR if request repeats the current configuration */
		759	pll_config = RCC->CFGR;
		760	if((READ_BIT(pll_config, RCC_CFGR_PLLSRC) != RCC_OscInitStruct->PLL.PLLSource) \|\|
		761	(READ_BIT(pll_config, RCC_CFGR_PLLMUL) != RCC_OscInitStruct->PLL.PLLMUL) \|\|
		762	(READ_BIT(pll_config, RCC_CFGR_PLLDIV) != RCC_OscInitStruct->PLL.PLLDIV))
		763	{
		764	return HAL_ERROR;
		765	}
		766	}
30	mjames	767	}
		768	}
50	mjames	769
30	mjames	770	return HAL_OK;
		771	}
		772
		773	/**
50	mjames	774	* @brief Initializes the CPU, AHB and APB buses clocks according to the specified
30	mjames	775	* parameters in the RCC_ClkInitStruct.
		776	* @param RCC_ClkInitStruct pointer to an RCC_OscInitTypeDef structure that
		777	* contains the configuration information for the RCC peripheral.
50	mjames	778	* @param FLatency FLASH Latency
30	mjames	779	* The value of this parameter depend on device used within the same series
50	mjames	780	* @note The SystemCoreClock CMSIS variable is used to store System Clock Frequency
30	mjames	781	* and updated by @ref HAL_RCC_GetHCLKFreq() function called within this function
		782	*
		783	* @note The MSI is used (enabled by hardware) as system clock source after
		784	* start-up from Reset, wake-up from STOP and STANDBY mode, or in case
		785	* of failure of the HSE used directly or indirectly as system clock
		786	* (if the Clock Security System CSS is enabled).
50	mjames	787	*
30	mjames	788	* @note A switch from one clock source to another occurs only if the target
50	mjames	789	* clock source is ready (clock stable after start-up delay or PLL locked).
30	mjames	790	* If a clock source which is not yet ready is selected, the switch will
50	mjames	791	* occur when the clock source will be ready.
30	mjames	792	* You can use @ref HAL_RCC_GetClockConfig() function to know which clock is
		793	* currently used as system clock source.
		794	* @note Depending on the device voltage range, the software has to set correctly
		795	* HPRE[3:0] bits to ensure that HCLK not exceed the maximum allowed frequency
		796	* (for more details refer to section above "Initialization/de-initialization functions")
		797	* @retval HAL status
		798	*/
		799	HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t FLatency)
		800	{
50	mjames	801	uint32_t tickstart;
		802	HAL_StatusTypeDef status;
		803
30	mjames	804	/* Check the parameters */
50	mjames	805	if(RCC_ClkInitStruct == NULL)
		806	{
		807	return HAL_ERROR;
		808	}
		809
30	mjames	810	assert_param(IS_FLASH_LATENCY(FLatency));
		811
50	mjames	812	/* To correctly read data from FLASH memory, the number of wait states (LATENCY)
		813	must be correctly programmed according to the frequency of the CPU clock
30	mjames	814	(HCLK) and the supply voltage of the device. */
		815
		816	/* Increasing the number of wait states because of higher CPU frequency */
50	mjames	817	if(FLatency > __HAL_FLASH_GET_LATENCY())
		818	{
30	mjames	819	/* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */
		820	__HAL_FLASH_SET_LATENCY(FLatency);
50	mjames	821
30	mjames	822	/* Check that the new number of wait states is taken into account to access the Flash
		823	memory by reading the FLASH_ACR register */
50	mjames	824	if(__HAL_FLASH_GET_LATENCY() != FLatency)
30	mjames	825	{
		826	return HAL_ERROR;
		827	}
		828	}
		829
		830	/-------------------------- HCLK Configuration --------------------------/
		831	if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_HCLK) == RCC_CLOCKTYPE_HCLK)
		832	{
		833	assert_param(IS_RCC_HCLK(RCC_ClkInitStruct->AHBCLKDivider));
		834	MODIFY_REG(RCC->CFGR, RCC_CFGR_HPRE, RCC_ClkInitStruct->AHBCLKDivider);
		835	}
		836
50	mjames	837	/------------------------- SYSCLK Configuration ---------------------------/
30	mjames	838	if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_SYSCLK) == RCC_CLOCKTYPE_SYSCLK)
50	mjames	839	{
30	mjames	840	assert_param(IS_RCC_SYSCLKSOURCE(RCC_ClkInitStruct->SYSCLKSource));
50	mjames	841
30	mjames	842	/* HSE is selected as System Clock Source */
		843	if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE)
		844	{
50	mjames	845	/* Check the HSE ready flag */
		846	if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == 0U)
30	mjames	847	{
		848	return HAL_ERROR;
		849	}
		850	}
		851	/* PLL is selected as System Clock Source */
		852	else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK)
		853	{
50	mjames	854	/* Check the PLL ready flag */
		855	if(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == 0U)
30	mjames	856	{
		857	return HAL_ERROR;
		858	}
		859	}
		860	/* HSI is selected as System Clock Source */
		861	else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSI)
		862	{
50	mjames	863	/* Check the HSI ready flag */
		864	if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == 0U)
30	mjames	865	{
		866	return HAL_ERROR;
		867	}
		868	}
		869	/* MSI is selected as System Clock Source */
		870	else
		871	{
50	mjames	872	/* Check the MSI ready flag */
		873	if(__HAL_RCC_GET_FLAG(RCC_FLAG_MSIRDY) == 0U)
30	mjames	874	{
		875	return HAL_ERROR;
		876	}
		877	}
		878	__HAL_RCC_SYSCLK_CONFIG(RCC_ClkInitStruct->SYSCLKSource);
		879
		880	/* Get Start Tick */
		881	tickstart = HAL_GetTick();
50	mjames	882
30	mjames	883	if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE)
		884	{
		885	while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_HSE)
		886	{
		887	if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE)
		888	{
		889	return HAL_TIMEOUT;
		890	}
		891	}
		892	}
		893	else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK)
		894	{
		895	while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_PLLCLK)
		896	{
		897	if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE)
		898	{
		899	return HAL_TIMEOUT;
		900	}
		901	}
		902	}
		903	else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSI)
		904	{
		905	while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_HSI)
		906	{
		907	if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE)
		908	{
		909	return HAL_TIMEOUT;
		910	}
		911	}
50	mjames	912	}
30	mjames	913	else
		914	{
		915	while(__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_MSI)
		916	{
		917	if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE)
		918	{
		919	return HAL_TIMEOUT;
		920	}
		921	}
		922	}
50	mjames	923	}
30	mjames	924	/* Decreasing the number of wait states because of lower CPU frequency */
50	mjames	925	if(FLatency < __HAL_FLASH_GET_LATENCY())
		926	{
30	mjames	927	/* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */
		928	__HAL_FLASH_SET_LATENCY(FLatency);
50	mjames	929
30	mjames	930	/* Check that the new number of wait states is taken into account to access the Flash
		931	memory by reading the FLASH_ACR register */
50	mjames	932	if(__HAL_FLASH_GET_LATENCY() != FLatency)
30	mjames	933	{
		934	return HAL_ERROR;
		935	}
50	mjames	936	}
30	mjames	937
50	mjames	938	/-------------------------- PCLK1 Configuration ---------------------------/
30	mjames	939	if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK1) == RCC_CLOCKTYPE_PCLK1)
		940	{
		941	assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB1CLKDivider));
		942	MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE1, RCC_ClkInitStruct->APB1CLKDivider);
		943	}
50	mjames	944
		945	/-------------------------- PCLK2 Configuration ---------------------------/
30	mjames	946	if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK2) == RCC_CLOCKTYPE_PCLK2)
		947	{
		948	assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB2CLKDivider));
50	mjames	949	MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE2, ((RCC_ClkInitStruct->APB2CLKDivider) << 3U));
30	mjames	950	}
50	mjames	951
30	mjames	952	/* Update the SystemCoreClock global variable */
50	mjames	953	SystemCoreClock = HAL_RCC_GetSysClockFreq() >> AHBPrescTable[(RCC->CFGR & RCC_CFGR_HPRE)>> RCC_CFGR_HPRE_Pos];
30	mjames	954
		955	/* Configure the source of time base considering new system clocks settings*/
50	mjames	956	status = HAL_InitTick(uwTickPrio);
		957
		958	return status;
30	mjames	959	}
		960
		961	/**
		962	* @}
		963	*/
		964
		965	/** @defgroup RCC_Exported_Functions_Group2 Peripheral Control functions
		966	* @brief RCC clocks control functions
		967	*
50	mjames	968	@verbatim
30	mjames	969	===============================================================================
		970	##### Peripheral Control functions #####
50	mjames	971	===============================================================================
30	mjames	972	[..]
50	mjames	973	This subsection provides a set of functions allowing to control the RCC Clocks
30	mjames	974	frequencies.
		975
		976	@endverbatim
		977	* @{
		978	*/
		979
		980	/**
		981	* @brief Selects the clock source to output on MCO pin.
		982	* @note MCO pin should be configured in alternate function mode.
		983	* @param RCC_MCOx specifies the output direction for the clock source.
		984	* This parameter can be one of the following values:
		985	* @arg @ref RCC_MCO1 Clock source to output on MCO1 pin(PA8).
		986	* @param RCC_MCOSource specifies the clock source to output.
		987	* This parameter can be one of the following values:
		988	* @arg @ref RCC_MCO1SOURCE_NOCLOCK No clock selected as MCO clock
		989	* @arg @ref RCC_MCO1SOURCE_SYSCLK System clock selected as MCO clock
		990	* @arg @ref RCC_MCO1SOURCE_HSI HSI selected as MCO clock
		991	* @arg @ref RCC_MCO1SOURCE_HSE HSE selected as MCO clock
50	mjames	992	* @arg @ref RCC_MCO1SOURCE_MSI MSI oscillator clock selected as MCO clock
30	mjames	993	* @arg @ref RCC_MCO1SOURCE_PLLCLK PLL clock selected as MCO clock
		994	* @arg @ref RCC_MCO1SOURCE_LSI LSI clock selected as MCO clock
		995	* @arg @ref RCC_MCO1SOURCE_LSE LSE clock selected as MCO clock
		996	* @param RCC_MCODiv specifies the MCO DIV.
		997	* This parameter can be one of the following values:
		998	* @arg @ref RCC_MCODIV_1 no division applied to MCO clock
		999	* @arg @ref RCC_MCODIV_2 division by 2 applied to MCO clock
		1000	* @arg @ref RCC_MCODIV_4 division by 4 applied to MCO clock
		1001	* @arg @ref RCC_MCODIV_8 division by 8 applied to MCO clock
		1002	* @arg @ref RCC_MCODIV_16 division by 16 applied to MCO clock
		1003	* @retval None
		1004	*/
		1005	void HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv)
		1006	{
50	mjames	1007	GPIO_InitTypeDef gpio;
30	mjames	1008
		1009	/* Check the parameters */
		1010	assert_param(IS_RCC_MCO(RCC_MCOx));
		1011	assert_param(IS_RCC_MCODIV(RCC_MCODiv));
		1012	assert_param(IS_RCC_MCO1SOURCE(RCC_MCOSource));
50	mjames	1013
30	mjames	1014	/* Configure the MCO1 pin in alternate function mode */
		1015	gpio.Mode = GPIO_MODE_AF_PP;
		1016	gpio.Speed = GPIO_SPEED_FREQ_HIGH;
		1017	gpio.Pull = GPIO_NOPULL;
		1018	gpio.Pin = MCO1_PIN;
		1019	gpio.Alternate = GPIO_AF0_MCO;
		1020
		1021	/* MCO1 Clock Enable */
		1022	MCO1_CLK_ENABLE();
50	mjames	1023
30	mjames	1024	HAL_GPIO_Init(MCO1_GPIO_PORT, &gpio);
50	mjames	1025
30	mjames	1026	/* Configure the MCO clock source */
		1027	__HAL_RCC_MCO1_CONFIG(RCC_MCOSource, RCC_MCODiv);
		1028	}
		1029
		1030	/**
		1031	* @brief Enables the Clock Security System.
		1032	* @note If a failure is detected on the HSE oscillator clock, this oscillator
		1033	* is automatically disabled and an interrupt is generated to inform the
		1034	* software about the failure (Clock Security System Interrupt, CSSI),
50	mjames	1035	* allowing the MCU to perform rescue operations. The CSSI is linked to
		1036	* the Cortex-M3 NMI (Non-Maskable Interrupt) exception vector.
30	mjames	1037	* @retval None
		1038	*/
		1039	void HAL_RCC_EnableCSS(void)
		1040	{
		1041	(__IO uint32_t ) RCC_CR_CSSON_BB = (uint32_t)ENABLE;
		1042	}
		1043
		1044	/**
		1045	* @brief Disables the Clock Security System.
		1046	* @retval None
		1047	*/
		1048	void HAL_RCC_DisableCSS(void)
		1049	{
		1050	(__IO uint32_t ) RCC_CR_CSSON_BB = (uint32_t)DISABLE;
		1051	}
		1052
		1053	/**
50	mjames	1054	* @brief Returns the SYSCLK frequency
		1055	* @note The system frequency computed by this function is not the real
		1056	* frequency in the chip. It is calculated based on the predefined
30	mjames	1057	* constant and the selected clock source:
		1058	* @note If SYSCLK source is MSI, function returns a value based on MSI
		1059	* Value as defined by the MSI range.
		1060	* @note If SYSCLK source is HSI, function returns values based on HSI_VALUE(*)
		1061	* @note If SYSCLK source is HSE, function returns a value based on HSE_VALUE(**)
50	mjames	1062	* @note If SYSCLK source is PLL, function returns a value based on HSE_VALUE(**)
		1063	* or HSI_VALUE(*) multiplied/divided by the PLL factors.
30	mjames	1064	* @note (*) HSI_VALUE is a constant defined in stm32l1xx_hal_conf.h file (default value
		1065	* 16 MHz) but the real value may vary depending on the variations
		1066	* in voltage and temperature.
		1067	* @note (**) HSE_VALUE is a constant defined in stm32l1xx_hal_conf.h file (default value
		1068	* 8 MHz), user has to ensure that HSE_VALUE is same as the real
		1069	* frequency of the crystal used. Otherwise, this function may
		1070	* have wrong result.
50	mjames	1071	*
30	mjames	1072	* @note The result of this function could be not correct when using fractional
		1073	* value for HSE crystal.
50	mjames	1074	*
		1075	* @note This function can be used by the user application to compute the
30	mjames	1076	* baud-rate for the communication peripherals or configure other parameters.
50	mjames	1077	*
30	mjames	1078	* @note Each time SYSCLK changes, this function must be called to update the
		1079	* right SYSCLK value. Otherwise, any configuration based on this function will be incorrect.
50	mjames	1080	*
30	mjames	1081	* @retval SYSCLK frequency
		1082	*/
		1083	uint32_t HAL_RCC_GetSysClockFreq(void)
		1084	{
50	mjames	1085	uint32_t tmpreg, pllm, plld, pllvco, msiclkrange, sysclockfreq;
		1086
30	mjames	1087	tmpreg = RCC->CFGR;
50	mjames	1088
30	mjames	1089	/* Get SYSCLK source -------------------------------------------------------*/
		1090	switch (tmpreg & RCC_CFGR_SWS)
		1091	{
		1092	case RCC_SYSCLKSOURCE_STATUS_HSI: /* HSI used as system clock source */
		1093	{
		1094	sysclockfreq = HSI_VALUE;
		1095	break;
		1096	}
		1097	case RCC_SYSCLKSOURCE_STATUS_HSE: /* HSE used as system clock */
		1098	{
		1099	sysclockfreq = HSE_VALUE;
		1100	break;
		1101	}
		1102	case RCC_SYSCLKSOURCE_STATUS_PLLCLK: /* PLL used as system clock */
		1103	{
50	mjames	1104	pllm = PLLMulTable[(uint32_t)(tmpreg & RCC_CFGR_PLLMUL) >> RCC_CFGR_PLLMUL_Pos];
		1105	plld = ((uint32_t)(tmpreg & RCC_CFGR_PLLDIV) >> RCC_CFGR_PLLDIV_Pos) + 1U;
30	mjames	1106	if (__HAL_RCC_GET_PLL_OSCSOURCE() != RCC_PLLSOURCE_HSI)
		1107	{
		1108	/* HSE used as PLL clock source */
50	mjames	1109	pllvco = (uint32_t)(((uint64_t)HSE_VALUE * (uint64_t)pllm) / (uint64_t)plld);
30	mjames	1110	}
		1111	else
		1112	{
		1113	/* HSI used as PLL clock source */
50	mjames	1114	pllvco = (uint32_t)(((uint64_t)HSI_VALUE * (uint64_t)pllm) / (uint64_t)plld);
30	mjames	1115	}
		1116	sysclockfreq = pllvco;
		1117	break;
		1118	}
		1119	case RCC_SYSCLKSOURCE_STATUS_MSI: /* MSI used as system clock source */
		1120	default: /* MSI used as system clock */
		1121	{
50	mjames	1122	msiclkrange = (RCC->ICSCR & RCC_ICSCR_MSIRANGE ) >> RCC_ICSCR_MSIRANGE_Pos;
		1123	sysclockfreq = (32768U * (1UL << (msiclkrange + 1U)));
30	mjames	1124	break;
		1125	}
		1126	}
		1127	return sysclockfreq;
		1128	}
		1129
		1130	/**
50	mjames	1131	* @brief Returns the HCLK frequency
30	mjames	1132	* @note Each time HCLK changes, this function must be called to update the
		1133	* right HCLK value. Otherwise, any configuration based on this function will be incorrect.
50	mjames	1134	*
		1135	* @note The SystemCoreClock CMSIS variable is used to store System Clock Frequency
30	mjames	1136	* and updated within this function
		1137	* @retval HCLK frequency
		1138	*/
		1139	uint32_t HAL_RCC_GetHCLKFreq(void)
		1140	{
		1141	return SystemCoreClock;
		1142	}
		1143
		1144	/**
50	mjames	1145	* @brief Returns the PCLK1 frequency
30	mjames	1146	* @note Each time PCLK1 changes, this function must be called to update the
		1147	* right PCLK1 value. Otherwise, any configuration based on this function will be incorrect.
		1148	* @retval PCLK1 frequency
		1149	*/
		1150	uint32_t HAL_RCC_GetPCLK1Freq(void)
		1151	{
		1152	/* Get HCLK source and Compute PCLK1 frequency ---------------------------*/
50	mjames	1153	return (HAL_RCC_GetHCLKFreq() >> APBPrescTable[(RCC->CFGR & RCC_CFGR_PPRE1) >> RCC_CFGR_PPRE1_Pos]);
		1154	}
30	mjames	1155
		1156	/**
50	mjames	1157	* @brief Returns the PCLK2 frequency
30	mjames	1158	* @note Each time PCLK2 changes, this function must be called to update the
		1159	* right PCLK2 value. Otherwise, any configuration based on this function will be incorrect.
		1160	* @retval PCLK2 frequency
		1161	*/
		1162	uint32_t HAL_RCC_GetPCLK2Freq(void)
		1163	{
		1164	/* Get HCLK source and Compute PCLK2 frequency ---------------------------*/
50	mjames	1165	return (HAL_RCC_GetHCLKFreq()>> APBPrescTable[(RCC->CFGR & RCC_CFGR_PPRE2) >> RCC_CFGR_PPRE2_Pos]);
		1166	}
30	mjames	1167
		1168	/**
50	mjames	1169	* @brief Configures the RCC_OscInitStruct according to the internal
30	mjames	1170	* RCC configuration registers.
50	mjames	1171	* @param RCC_OscInitStruct pointer to an RCC_OscInitTypeDef structure that
30	mjames	1172	* will be configured.
		1173	* @retval None
		1174	*/
		1175	void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct)
		1176	{
		1177	/* Check the parameters */
50	mjames	1178	assert_param(RCC_OscInitStruct != (void *)NULL);
30	mjames	1179
		1180	/* Set all possible values for the Oscillator type parameter ---------------*/
		1181	RCC_OscInitStruct->OscillatorType = RCC_OSCILLATORTYPE_HSE \| RCC_OSCILLATORTYPE_HSI \
		1182	\| RCC_OSCILLATORTYPE_LSE \| RCC_OSCILLATORTYPE_LSI \| RCC_OSCILLATORTYPE_MSI;
		1183
		1184
		1185	/* Get the HSE configuration -----------------------------------------------*/
		1186	if((RCC->CR &RCC_CR_HSEBYP) == RCC_CR_HSEBYP)
		1187	{
		1188	RCC_OscInitStruct->HSEState = RCC_HSE_BYPASS;
		1189	}
		1190	else if((RCC->CR &RCC_CR_HSEON) == RCC_CR_HSEON)
		1191	{
		1192	RCC_OscInitStruct->HSEState = RCC_HSE_ON;
		1193	}
		1194	else
		1195	{
		1196	RCC_OscInitStruct->HSEState = RCC_HSE_OFF;
		1197	}
		1198
		1199	/* Get the HSI configuration -----------------------------------------------*/
		1200	if((RCC->CR &RCC_CR_HSION) == RCC_CR_HSION)
		1201	{
		1202	RCC_OscInitStruct->HSIState = RCC_HSI_ON;
		1203	}
		1204	else
		1205	{
		1206	RCC_OscInitStruct->HSIState = RCC_HSI_OFF;
		1207	}
50	mjames	1208
		1209	RCC_OscInitStruct->HSICalibrationValue = (uint32_t)((RCC->ICSCR & RCC_ICSCR_HSITRIM) >> RCC_ICSCR_HSITRIM_Pos);
		1210
30	mjames	1211	/* Get the MSI configuration -----------------------------------------------*/
		1212	if((RCC->CR &RCC_CR_MSION) == RCC_CR_MSION)
		1213	{
		1214	RCC_OscInitStruct->MSIState = RCC_MSI_ON;
		1215	}
		1216	else
		1217	{
		1218	RCC_OscInitStruct->MSIState = RCC_MSI_OFF;
		1219	}
50	mjames	1220
		1221	RCC_OscInitStruct->MSICalibrationValue = (uint32_t)((RCC->ICSCR & RCC_ICSCR_MSITRIM) >> RCC_ICSCR_MSITRIM_Pos);
30	mjames	1222	RCC_OscInitStruct->MSIClockRange = (uint32_t)((RCC->ICSCR & RCC_ICSCR_MSIRANGE));
50	mjames	1223
30	mjames	1224	/* Get the LSE configuration -----------------------------------------------*/
		1225	if((RCC->CSR &RCC_CSR_LSEBYP) == RCC_CSR_LSEBYP)
		1226	{
		1227	RCC_OscInitStruct->LSEState = RCC_LSE_BYPASS;
		1228	}
		1229	else if((RCC->CSR &RCC_CSR_LSEON) == RCC_CSR_LSEON)
		1230	{
		1231	RCC_OscInitStruct->LSEState = RCC_LSE_ON;
		1232	}
		1233	else
		1234	{
		1235	RCC_OscInitStruct->LSEState = RCC_LSE_OFF;
		1236	}
50	mjames	1237
30	mjames	1238	/* Get the LSI configuration -----------------------------------------------*/
		1239	if((RCC->CSR &RCC_CSR_LSION) == RCC_CSR_LSION)
		1240	{
		1241	RCC_OscInitStruct->LSIState = RCC_LSI_ON;
		1242	}
		1243	else
		1244	{
		1245	RCC_OscInitStruct->LSIState = RCC_LSI_OFF;
		1246	}
		1247
50	mjames	1248
30	mjames	1249	/* Get the PLL configuration -----------------------------------------------*/
		1250	if((RCC->CR &RCC_CR_PLLON) == RCC_CR_PLLON)
		1251	{
		1252	RCC_OscInitStruct->PLL.PLLState = RCC_PLL_ON;
		1253	}
		1254	else
		1255	{
		1256	RCC_OscInitStruct->PLL.PLLState = RCC_PLL_OFF;
		1257	}
		1258	RCC_OscInitStruct->PLL.PLLSource = (uint32_t)(RCC->CFGR & RCC_CFGR_PLLSRC);
		1259	RCC_OscInitStruct->PLL.PLLMUL = (uint32_t)(RCC->CFGR & RCC_CFGR_PLLMUL);
		1260	RCC_OscInitStruct->PLL.PLLDIV = (uint32_t)(RCC->CFGR & RCC_CFGR_PLLDIV);
		1261	}
		1262
		1263	/**
50	mjames	1264	* @brief Get the RCC_ClkInitStruct according to the internal
30	mjames	1265	* RCC configuration registers.
50	mjames	1266	* @param RCC_ClkInitStruct pointer to an RCC_ClkInitTypeDef structure that
30	mjames	1267	* contains the current clock configuration.
		1268	* @param pFLatency Pointer on the Flash Latency.
		1269	* @retval None
		1270	*/
		1271	void HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef RCC_ClkInitStruct, uint32_t pFLatency)
		1272	{
		1273	/* Check the parameters */
50	mjames	1274	assert_param(RCC_ClkInitStruct != (void *)NULL);
		1275	assert_param(pFLatency != (void *)NULL);
30	mjames	1276
		1277	/* Set all possible values for the Clock type parameter --------------------*/
		1278	RCC_ClkInitStruct->ClockType = RCC_CLOCKTYPE_SYSCLK \| RCC_CLOCKTYPE_HCLK \| RCC_CLOCKTYPE_PCLK1 \| RCC_CLOCKTYPE_PCLK2;
50	mjames	1279
		1280	/* Get the SYSCLK configuration --------------------------------------------*/
30	mjames	1281	RCC_ClkInitStruct->SYSCLKSource = (uint32_t)(RCC->CFGR & RCC_CFGR_SW);
50	mjames	1282
		1283	/* Get the HCLK configuration ----------------------------------------------*/
		1284	RCC_ClkInitStruct->AHBCLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_HPRE);
		1285
		1286	/* Get the APB1 configuration ----------------------------------------------*/
		1287	RCC_ClkInitStruct->APB1CLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_PPRE1);
		1288
		1289	/* Get the APB2 configuration ----------------------------------------------*/
		1290	RCC_ClkInitStruct->APB2CLKDivider = (uint32_t)((RCC->CFGR & RCC_CFGR_PPRE2) >> 3U);
		1291
		1292	/* Get the Flash Wait State (Latency) configuration ------------------------*/
		1293	*pFLatency = __HAL_FLASH_GET_LATENCY();
30	mjames	1294	}
		1295
		1296	/**
		1297	* @brief This function handles the RCC CSS interrupt request.
		1298	* @note This API should be called under the NMI_Handler().
		1299	* @retval None
		1300	*/
		1301	void HAL_RCC_NMI_IRQHandler(void)
		1302	{
		1303	/* Check RCC CSSF flag */
		1304	if(__HAL_RCC_GET_IT(RCC_IT_CSS))
		1305	{
		1306	/* RCC Clock Security System interrupt user callback */
		1307	HAL_RCC_CSSCallback();
50	mjames	1308
30	mjames	1309	/* Clear RCC CSS pending bit */
		1310	__HAL_RCC_CLEAR_IT(RCC_IT_CSS);
		1311	}
		1312	}
		1313
		1314	/**
		1315	* @brief RCC Clock Security System interrupt callback
		1316	* @retval none
		1317	*/
		1318	__weak void HAL_RCC_CSSCallback(void)
		1319	{
		1320	/* NOTE : This function Should not be modified, when the callback is needed,
		1321	the HAL_RCC_CSSCallback could be implemented in the user file
50	mjames	1322	*/
30	mjames	1323	}
		1324
		1325	/**
		1326	* @}
		1327	*/
		1328
		1329	/**
		1330	* @}
		1331	*/
		1332
		1333	/* Private function prototypes -----------------------------------------------*/
		1334	/** @addtogroup RCC_Private_Functions
		1335	* @{
		1336	*/
		1337	/**
50	mjames	1338	* @brief Update number of Flash wait states in line with MSI range and current
30	mjames	1339	voltage range
		1340	* @param MSIrange MSI range value from RCC_MSIRANGE_0 to RCC_MSIRANGE_6
		1341	* @retval HAL status
		1342	*/
		1343	static HAL_StatusTypeDef RCC_SetFlashLatencyFromMSIRange(uint32_t MSIrange)
		1344	{
50	mjames	1345	uint32_t vos;
30	mjames	1346	uint32_t latency = FLASH_LATENCY_0; /* default value 0WS */
		1347
		1348	/* HCLK can reach 4 MHz only if AHB prescaler = 1 */
		1349	if (READ_BIT(RCC->CFGR, RCC_CFGR_HPRE) == RCC_SYSCLK_DIV1)
		1350	{
		1351	if(__HAL_RCC_PWR_IS_CLK_ENABLED())
		1352	{
50	mjames	1353	vos = READ_BIT(PWR->CR, PWR_CR_VOS);
30	mjames	1354	}
		1355	else
		1356	{
		1357	__HAL_RCC_PWR_CLK_ENABLE();
50	mjames	1358	vos = READ_BIT(PWR->CR, PWR_CR_VOS);
30	mjames	1359	__HAL_RCC_PWR_CLK_DISABLE();
		1360	}
50	mjames	1361
30	mjames	1362	/* Check if need to set latency 1 only for Range 3 & HCLK = 4MHz */
		1363	if((vos == PWR_REGULATOR_VOLTAGE_SCALE3) && (MSIrange == RCC_MSIRANGE_6))
		1364	{
		1365	latency = FLASH_LATENCY_1; /* 1WS */
		1366	}
		1367	}
50	mjames	1368
30	mjames	1369	__HAL_FLASH_SET_LATENCY(latency);
50	mjames	1370
30	mjames	1371	/* Check that the new number of wait states is taken into account to access the Flash
		1372	memory by reading the FLASH_ACR register */
50	mjames	1373	if(__HAL_FLASH_GET_LATENCY() != latency)
30	mjames	1374	{
		1375	return HAL_ERROR;
		1376	}
50	mjames	1377
30	mjames	1378	return HAL_OK;
		1379	}
		1380
		1381	/**
		1382	* @}
		1383	*/
50	mjames	1384
30	mjames	1385	#endif /* HAL_RCC_MODULE_ENABLED */
		1386	/**
		1387	* @}
		1388	*/
		1389
		1390	/**
		1391	* @}
		1392	*/
		1393
		1394	/********************** (C) COPYRIGHT STMicroelectronics *END OF FILE**/

Subversion Repositories DashDisplay

(root)/branches/Dashboard_L152_v2/Drivers/STM32L1xx_HAL_Driver/Src/stm32l1xx_hal_rcc.c – Rev 50